Home

Chapter 3

1. It is suggested that the computer used for the Player program has at least an 800MHz Pentium III Intel Pentium Dual Core 2 2GHz recommended If your CPU is slower than this video clips recorded at maximum speed with very high image quality will be played back slowly Also DirectX 9 0 or higher is required to install and the VGA card with 16MB or higher video RAM is recommended for proper operation Proper image display depends on the display settings of your PC If you are experiencing display problems click the right mouse button on the background screen and select Properties Settings then set the Color quality to 32 bit Then select Advanced Troubleshoot and then set the Hardware Acceleration to Full Please make sure that DirectX version 9 0 or higher has been installed if the display problem continues To check the version of DirectX click Start RUN and type dxdiag then hit the enter key which will display DirectX Diagnostic Tool dialog box Then move to the Display tab and make sure DirectDraw Acceleration is set to Enabled Test DirectDraw by selecting the DirectDraw Test button when using the Microsoft Windows XP operating system Please check the driver version of the video card and update it to the latest version available If you still have display problems after changing all display settings as described above try replacing the video card Video cards with an ATI chipset are recommended If you se
2. Map Editor p 71 for details about map registration Map monitoring is supported in the Live panel maximum 4 and Map panel If the Live or Map tab is not on the tab panel go to the System menu click New Tab and then Live or Map 44 iRAS Remote Administration System Select a desired map from the M ap list and drag and drop it on nas Remote Administration System admin Live 1 Map1 System View Playback About the Live screen The selected map is displayed on the screen You can move a map to the desired location on the Live screen without disconnecting the current connection while monitoring video Selecting an input output device on the map and dragging and dropping it on the Live screen Play panel or Device Status panel allows you to monitor or play back video or to monitor device status Live 1 BANK 1 RAS Remote Administration System admin Live 1 Mapi System View Playback About Live 1 BANK 1 Hovering the mouse cursor over the input output device on the map displays the event detection and status of the input output device When the input output device detects any event or is not working properly the following icons appear sequentially to the maximum of 4 at a time some event icons may not be supported depending on the specifications and version of the device Unplugged dn Event Off Irregular e Motion Video Blind Es Video Loss x Object Detection e Video Analytics Detection
3. Click the Live tab on the tab panel Select a site to connect MEESCH from the Site list and drag and drop it on the Live screen ai ia ii jii Live video from the selected site is displayed on the screen You can move a camera screen to the desired location on the Live screen without disconnecting the current connection while monitoring video Select a camera screen and drag and drop it on the desired location NOTE The iRAS system performance might seriously deteriorate when simultaneously monitoring or playing back video with 1280x720 or higher resolution on more than one camera screen Panel Toolbar The panel toolbar at the bottom allows you to control the Live panel e E Save to User Layout Saves the current screen format A 72D Screen Format Changes the screen format Clicking the M button displays more screen formats Clicking the D or Di button moves to the previous or next camera groups e El Layout Sequence Starts or stops layout sequence Refer to Layout Sequence Monitoring p 40 for details e Ed Hotspot Sets up a selected camera screen as a hotspot screen Refer to Hotspot Setup p 38 for details e E Event Spot Sets up a selected camera screen as an event spot screen Refer to Event Spot Setup p 38 for details 37 User s Manual e E Map Event Spot Sets up a selected camera screen as a map event spot screen Refer to Map Event Spot Setup p 39 for details Expor
4. Health Log Displays log entries of the system health monitoring for the registered devices Device System Log Displays system log entries from the devices Device Event Log Displays event log entries from the devices If the device is a network camera or network video transmitter not all event logs are displayed but only the events that occurred while recording on an SD SDHC memory card is enabled Admin Service Log Displays log entries from the administration service Ask your dealer or distributor for details Monitoring Service Log Displays log entries for monitoring service Ask your dealer or distributor for details Incremental Search Allows you to search for a log Entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found within the selected group As you enter more text the results narrow Report Toolbar The toolbar at the bottom of the panel allows you to search for the desired log entries 69 User s Manual TAS E e Fom 200 0225 te EE Tos E ET ETS H First ES e From To Set up the date and time of the log entry to search Enter a specific date and time or select First or Last Clicking the 1 Hour 6 Hour Today 3 Day or 1 Week button adjusts the time interval between From and To Selecting First or Last searches log entries from the first or to the last e D Condition Selects a log type
5. Trip Zone Tampering 8 Audio Detection ID Alarm In Alarm Out Event detection is displayed according to the event detection settings and Irregular is based on the system check settings on the device that the input output device is connected Event detection and status are displayed in unique colors if you have set up status color during the map setup When more than one event or status is detected at the same time the color reflecting each event detection or status is displayed sequentially Path n You can monitor video from multiple cameras sequentially on a map in the same camera screen during map monitoring A path sequence should be set up for path sequence monitoring Refer to 11 2 Setting up Map Path Sequence p 74 for details about the path sequence setup 45 User s Manual Select a desired path of the path ras Remote Administration System admin Live 1 Mapi sequence from the map and drag and SV ee drop it on the Live screen Video from the cameras associated to the path sequence is displayed sequentially during the preset duration period Site 6 3 Controlling Cameras A control toolbar and a screen menu are provided for controlling camera Control Toolbar When selecting a camera screen and hovering the mouse cursor over the camera screen the control toolbar 1s displayed over that camera screen The control toolbar allows you to control the selected camera Hovering the mouse cursor over a bu
6. System Overview Menu Refer to Menu p 14 for details Site List Allows you to connect to the registered site by using the mouse drag and drop Refer to Site List p 15 for details Instant Event List Displays a list of events notified from registered devices Clicking the w button displays the Emergency Event panel Refer to 5 9 Instant Event p 32 and Chapter 8 Event Handling p 63 for details Live Popup List Displays the list of live popup screens currently displayed on the monitor Refer to 6 4 Controlling Maps Live Popup p 51 for details about the live popup screen Panel Toolbar Timetable Displays the toolbar or timetable depending on the panel Refer to 6 3 Controlling Cameras p 46 or Chapter 7 Recorded Video Playback amp Exportation p 53 for details Panel Allows you to select which panel to use Refer to Panel p 16 for details 13 User s Manual Menu 7 RAS Remote Administration System admin Live 1 e New Tab Adds panels A maximum of 8 panels are supported for Live and Play panels altogether and 2 panels for Map panel One of each is supported for Report Health and Status panels Playback System About New Tab Remove gt View Live 1 1 Ctrl E S Ctrl P Remove Removes selected devices or cameras or all cameras from Live or Play screen Export Print RAS Setup gt e
7. USER SMANUAL iRAS Remote Administration System Table of Contents G apter En de ele de WEE 1 Med PO AUIS aguilera 1 El ee E E le RE 3 24 Producto Malaria elia ea 3 le Ee o loco 3 System Requirements 3 2 2 ee Mere EE 3 2 rinsaldare ir ia 5 Chapter EECHER ee 7 Logistica 7 3 2 Registering Devices ricca 7 3 3 Live Video Monto Misco nt 10 3 4 Playing Recorded VIDEO eta 11 Chapter 4 System Overvi W ii 13 A anal 14 ole Liste elle 15 lte O A TO aai 16 Chapiero O EUD a a a lai 17 Sul Devo ani erat E vad resbala e 17 Managing Devices 18 PA eee IT RAI E N 23 User Management 24 5 3 Panie 52160 AAA PP E E T 26 SE LUMI acta en in gy ec ean tr ceca Ae lnc E aie 27 A II A 28 SA a eo eee ee 29 5 7 Video ENnanco me dealer 30 Se Replica 31 Sal a a a a a a a 32 BVO ING WORK eege Ee 33 AMA dai 34 5 12 Backup Restos a a oe 35 Chapter 6 Live Video Monitoring 37 S biet Weigel EE 37 Layout Monto MING 39 Layout Sequence Monitoring snsannnnnnennnnnnosennennrnnnrrnsnnnnressnnrrnrsnnrerensnnenee 40 Camera Sequence Monitoring i 43 6 2 Map MOON sasaki oe 44 6 3 CONTORNO E AMAS ii dit 46 PACO TO sr a ln date ur as lb rd e 47 User s Manual ZOOM COMO rn 48 Made Eterna aa 49 TEXTO VIEW dilatan nocilla 49 6 4 COntroling Maps ela 49 HVE RODUD iaa ara 51 Chapter 7 Recorded Video Playback amp Exportation nnannnnennnnennenen
8. edi Remember my ID on this computer Check the box if you EZ Remember my ID on this computer want to save your ID for logging on GE e Restore last Live sessions Check the box if you want to restore OK the previous live monitoring sessions in the current Live panels 3 2 Registering Devices You must register devices on the iRAS program and add the devices to a device group in order to perform any operation 1 Go to the System menu Select IRAS Setup Select Device System View Playback About New Tab Remove Export Ctrl E Print Ctrl P User Panic Record System Ctrl Shift S Screen Format Exit Screen Display Video Enhancement Report Instant Event Network Map Backup Restore Lock Ctri Alt L 2 Click All Devices in the Site panel and then the F button at the bottom of the Site List panel The Device Scan window appears User s Manual eN Auto Scan LAN y select All Name 10 0 113 71 Description Description Description e Protocol Select the protocol or manufacturer of the device to scan e Scan Mode Select the scan mode Clicking the Start Scan button displays the results in the list If the IP address range of the device is different from that of the RAS system the RAS program considers the IP address invalid In this case you must change the device s IP address to register the device Auto Scan LAN List
9. second eve O i The name will be updated automatically when the name of the device to which the input output device is connected is updated Associated Audio Channel Select the audio channel to associate with the camera for audio recording supported only for a camera Device Type Alarm In The selected audio channel will be recorded when video from a the camera is recorded Associated Device Select a camera channel to associate with the alarm in or audio in device for display on the event spot screen supported only for an alarm in or audio in device Video from the selected camera channel will be displayed on the event spot screen when an alarm in or audio in event is detected Additional Information The User menu allows you to register and manage users or user groups 23 User s Manual Name Description e Group Group Panel Displays a user group list The Administrators group has authority to perform all functions and the authority settings cannot be edited e Name ID Email Phone Description User List Panel Displays the list and information about users registered in each group e Incremental Search Allows you to search for a user registered in each group Selecting a group in the Group Panel and entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found within the selected group AS you enter more text the resu
10. to start the installation Unpacking packages NOTE NET Framework and the Visual C Runtime Libraries are installed automatically and it may take some time This installation step will be skipped if the programs are already installed on your computer iRAS Remote Administration System 7 When the following screen appears click the Close button Gigs to complete the installation Installation Complete RAS has been installed successfully Click Close to exit 8 There is no default password It is recommended that you REESE set up a password for security before using this program KR You can add user account and change password at System gt iRAS Setup gt User category OK 1 Stop running the iRAS program first NOTE The iRAS software might not be uninstalled correctly if you uninstall it while the program is running CAUTION The iRAS software should be uninstalled following the procedures below If you delete the installation folder manually the iRAS software cannot be uninstalled or reinstalled 2 Go to the Start Menu and click IRAS Click Uninstall iRAS 3 Click Yes when the following screen appears Uninstall iRAS Are you sure you want to uninstall this product OK Cancel 4 Click the Remove All or Do not remove button when the following screen appears Clicking the Remove All button deletes all saved data including panic recorded video and previous settings in the system C
11. KEE EE from the Site list and drag and drop it on the Play screen st i AE Recorded video from the selected site is displayed on the screen You can move a camera screen to the desired location on the Play screen without stopping the current playback while playing back video Select a camera screen and drag and drop it on the desired location Site Play 1 If a layout is registered on the RAS program you can play video in the layout format by selecting a desired layout from the Layout list and dragging and dropping it on the Play screen Refer to 6 1 Monitoring Video Layout Monitoring Registering Layouts p 39 for details about the registration of a layout NOTES e The iRAS system performance might seriously deteriorate when simultaneously monitoring or playing back video with 1280x720 or higher resolution on more than one camera screen e A layout in this manual refers to a screen organization created by arranging specific cameras in a specific screen format 3 A panel toolbar a timetable a control toolbar and a screen menu are provided for playing back recorded video Panel Toolbar The toolbar at the bottom of the panel allows you to search and play back recorded video NOTE The toolbar may be different and some functions below may not be supported depending on the specifications and version of the device 53 User s Manual 54 O O Event Search Time Lapse Search Switches search mode between even
12. as follows When searching for video recorded on an SD SDHC memory card not all events are searched but only the events that occurred while recording on an SD SDHC memory card is enabled Date Time e Clicking an event from the list displays the event recorded video on the screen if the events were recorded during Event recording Clicking the button in the top right corner of the event list displays next results Control Toolbar The control toolbar is displayed over a selected camera screen when hovering the mouse cursor over the camera screen Hovering the mouse cursor over each button displays a tooltip for the button e CG Object Motion Search Allows you to search for changes or motion in recorded images in the device or the iRAS system Refer to Object Motion Search p 57 for details e Image Zoom Zooms in on the image Refer to Zoom Control p 58 for details e 3 Color Control Adjusts the brightness contrast saturation and hue of the current video Clicking the e button cancels the adjustment and reloads the original image This change will not be applied to the recorded video e EA Image Effect Adjusts the image effect Refer to Image Effect p 58 for details e 4 Audio Play Plays audio when playing back video that has recorded audio 1x1 screen format only PI reen Men The screen menu is displayed when selecting a camera screen and clicking the right mouse button EEN e Image Zoom Func
13. at a time by selecting the icons or links and clicking the icon alignment button kd Position Aligns one or more icons to the center vertically or horizontally on the background image 72 iRAS Remote Administration System e 54 86 O B A H Position Aligns two or more icons to the top or bottom to the vertical or horizontal center or to the left or right based on the last selected icon e D H Distance Equalizes the distance between each icon of three or more icons e B G B Size Equalizes the width height or size of two or more icons supported only for icons that are of the same type but of a different width height ratio Property You can set up properties of the canvas or input output device icons or map links on the canvas Select the canvas icons or map links and then each field of the property You can enter or select a value from the drop down list General General Text test Name Alarm In Font Microsoft Sans Serif lcon Alarm In Sensor General Font Size 9 Ratio 50 Name BANK 1 Text Color W 000 Map Attributes X Coordinate 416 X Coordinate 139 Background Color 255 255 255 Root Map Not Use Y Coordinate 75 Y Coordinate 401 Align Text Left Top Canvas Width 32 Width 128 Bold Not Use Width 800 Height 32 Height 32 Italic Not Use Height 600 Associated Camera Select target Text Color _ 255 255 255 Underline Not Use Color 255 255 255 Halo effect Not Use Background Color MY 85 110 215 St
14. About Displays the software version and copyright information System View Playback About Site List Displays the list of registered sites e Incremental Search Allows you to search for a registered device or site Entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found As you enter more text the results narrow e All Devices Displays the list of devices registered on the iRAS program Clicking a device in the list and dragging and dropping it in the desired location on the screen allows you to monitor video from the cameras connected to the device or to play back recorded video from the cameras This is supported only for the users in the Administrator group Device Group Displays the list of registered device groups Clicking a device in the list and dragging and dropping it in the desired location on the screen allows you to monitor video from the cameras connected to the device or to play back recorded video from the cameras Refer to 6 1 Monitoring Video p 37 or 7 1 Playing back Recorded Video p 53 for details Layout Displays the list of registered layouts Clicking a layout in the list and dragging and dropping it on the screen starts layout monitoring or playback Refer to 6 1 Monitoring Video p 37 or 7 1 Playing back Recorded Video p 53 for details Layout Sequence Displays the list of registered layout sequ
15. Event Spot Sets up a selected camera screen as an event spot screen Refer to 6 1 Monitoring Video Event Spot Setup p 38 for details Set Map Event Spot Sets up a selected camera screen as a map event spot screen Refer to 6 1 Monitoring Video Map Event Spot Setup p 39 for details Layout Sequence Starts or stops the layout sequence Refer to 6 1 Monitoring Video Layout Sequence Monitoring p 40 for details Emergency Event Panel Displays the Emergency Event panel Refer to Chapter 8 Event Handling p 63 for details Remote Site Panel Displays or hides a site list in the floating panel or full screen This is supported for not every panel k Play Pause Plays or pauses playback of recorded video System View Playback About e Go To Selects a specific point of video to be played Refer to 7 1 Playing back Recorded Video Panel Toolbar p 53 for details e Step Playback Moves the video forward or backward in the frame or time unit Go to Step Playback gt Export Video File D Export Video File Exports recorded video as a self player file exe or an AVI file avi iRAS Remote Administration System e Snapshot on Motion Displays snapshot of images recorded during the event based recording event and pre event in the Play panel Refer to 7 1 Playing back Recorded Video Snapshot on Motion Event p 57 for details i Ras Remote Administration System admin Live 1 e
16. Panic Recording and Green for Irregular recording caused by temporary disconnection from the device Hour Segments Timetable some DVR models only Yellow color bar Indicates the current playback location of video on the timetable Pink color bar Gray color bar Indicates the segment of video that is currently displayed not displayed on the screen when time overlap occurs Clicking the E4 Additional Menu button in the Play panel allows you to change the segment to be displayed on the screen Click the Additional Menu button Select the Select Segment menu Select a desired segment gt The first image recorded within the selected segment is displayed on the screen NOTE If the iRAS system s or device s time and date have been reset to a time that is earlier than previously recorded video it is possible that there is more than one video segment in the same time range due to time overlap In this case you can individually play video recorded during the overlapping time by selecting a segment For example when the iRAS system or device has recorded video from one to five o clock and the user changes the time backward from five to three o clock and then continues recording until six o clock there will be two segments from three to five o clock 1 i E z LA Segment 2 f i 55 User s Manual e Event Search Mode When in the event search mode the event list is displayed at the bottom of the screen
17. Status panel H Panic Recording Starts or stops panic recording remotely supported only for DVRs with the panic recording function Rec From To Displays the recording period Status Displays the status of recording playback archiving exporting of recorded video fe Full Screen Displays the Status panel in full screen format 68 iRAS Remote Administration System Chapter 10 Log Search You can search log entries for the RAS program and the devices Log search is supported in the Report panel If the Report tab is not on the tab panel go to the System menu click New Tab and Report on System admir System View Playback O NewiTab ld Live Remove Play Ma istration System admin Report Export Ctrl E map print Cti P_ Report RAS Setup gt System View Playback About Health Site mopon Status Logout Lock Ctrl Alt L Exit The various types of log entries are displayed Clicking the right mouse button on a column header displays a menu and allows you to sort data as you want ration System admin Report Playback About Report ETA el _ _ __ _ 2012 10 31 15 31 54 LogIn admin 2012 10 31 15 31 46 Client Start 2012 10 31 14 33 05 Add to Live tab lt no name gt lt no name gt admin e Log type Select a log type to search from the drop down list User Log Displays log entries from the iRAS program
18. The Export Video File window appears and allows you to export video of the selected period as a self player file exe or an AVI file avi Refer to Exporting as a Self Player File p 59 and Exporting as an AVI File p 61 for details e Export Video File Sets up the section of video to be exported by entering the date and time manually Select Export Video File from the export menu The Export Video File window appears and allows you to export video for the period as a self player file exe or an AVI file avi Refer to Exporting as a Self Player File p 59 and Exporting as an AVI File p 61 for details e Reserved Self Player Displays the list of reservations of exporting as a self player file Clicking the El button performs the reserved exporting manually and clicking the if button cancels the reservation Refer to Exporting as a Self Player File p 59 for details about reservation of exporting as a self player file Exporting as a Self Player File The recorded video is exported as a self player file exe o De lt n0 name e From To Enter the date and time of video to export From i Fist S Selecting First sets the date and time to the date and Ll 5 time of the first recorded video Selecting Last sets A E lini the date and time to the date and time of the last Ao recorded video Clicking the EI Minute 3 HA Minute 10 Minute 30 Minute or 4 60 ZJE Info Desk Minute button increases or decreases by t
19. Toolbar p 46 for details Reload e List Displays the list of the previous or next connected maps Selecting a map Auto Focusing from the list moves to the selected map e Reload Reloads the connection of the current map e Focusing Event Focusing Duration Allows you to set up auto focusing events Actual Size x1 d i A and duration Refer to 5 11 Map p 34 for details Zoom In e Remove Disconnects the current connection Remove Live Popup H reen You can monitor live video from a camera with a detected event during map monitoring Popup screens appear based on the settings in Map Editor Event property Live Popup action when events are detected The Live Popup list displays the list of live popup screens currently displayed on the monitor When selecting a popup screen and hovering the mouse cursor over the popup screen the control toolbar is displayed over that popup screen The control toolbar allows you to control the camera Hovering the mouse cursor over a button displays a tooltip for the button Refer to 6 3 Controlling Cameras Control Toolbar p 49 for details about the toolbar buttons When clicking the right mouse button on the popup screen a popup screen menu is displayed The screen menu allows you to change the popup screen settings or to control the camera Items related to controlling a camera in the menu function the same way as those in the live screen menu Refer to 6 3 Controlling Cameras L
20. all saved data and the deleted data cannot be restored 82 iRAS Remote Administration System Index C CallbacK Port n een 32 Camera Control Toolbar 46 Clip STEE 60 Control TOODI Rana inde 56 D Device 1 7 E EVENE A a 13 64 Event ODO sra 38 H o ai 38 IRAS SCIUD tasas 14 IS ila 7 L LAVO eenn a 39 41 53 LIVE Populi rs 13 51 Live Screen MENU 46 M Map Control Toolbar ss sssssnnsssensssseessssesseess 49 Map Event DO literaria 39 Map Screen MENU ceci 50 V1 3 Mer Udala 13 p Panella 13 Panel Toolbar 37 53 panic recording seal 46 Path Seouence aminin mini n 45 Pilla 48 58 Play Screen MENU lla 56 Al a E E SN 51 Prese lion 48 R Report TODD ioni 69 S CR RR ERE 18 SERS Free cates 13 LEET cae canteens 18 Me QING ida 18 Snapshot on Motion Event 57 T Time Overlap 55 Timetable Event Uert 55 U User Group Panel 24 UserPanela lille 24 83 User s Manual lt Comielit _______ BB BOSS Passion and Innovation Via Don Arrigoni 5 24020 Rovetta S Lorenzo Bergamo http www comelitgroup com e mail export department comelit it 84 V1 3
21. are displayed immediately as matching text is found As you enter more text the results narrow e Selected Layout Sequence List Displays the list of layouts registered for the layout sequence Duration sec displays the duration for each layout to be displayed on the screen Clicking the Apply all button applies the duration setting to all layouts in the list Select a layout from Layout List click the button and the selected layout is added to Selected Layout Sequence List Clicking the OK button completes registration of the layout sequence iRAS Remote Administration System Camera Sequence Monitoring You can monitor video from multiple cameras in the same camera screen sequentially A camera sequence should be registered on the RAS program for camera sequence monitoring Refer to the following for details about camera sequence registration 1 Select a desired camera sequence from the Camera nas Remote Administration System admin Live 1 Inside 1 System View Playback About Sequence list and drag and drop it on the Live screen Video from cameras added to the camera sequence is displayed on the screen sequentially Site Live 1 2 Clicking the Y Camera Sequence button on the camera screen control toolbar stops or starts the camera sequence Example Camera Sequence Registerin mer n 1 Go to the System menu and click RAS Setup and select the Device menu 2 Click Camera Sequence in the Si
22. iRAS system considers the device as a new device Refer to Managing Devices p 18 for details about registering a device or device group or Chapter 6 Live Video Monitoring p 37 for details about registering a layout or sequence NOTE In this manual a site refers to a device group layout or sequence registered on the iRAS program site All Devices Displays devices registered in the RAS program Refer to 3 2 Registering Devices p 7 for details about registering devices Device Group Displays registered device groups You can monitor or play back recorded video from the cameras in device groups You must register devices in the RAS program and add the devices to a device group to perform any operation Refer to 3 2 Registering Devices p 7 for details about registering device groups Layout Displays the registered layouts You can monitor video from multiple cameras in a predefined layout Refer to 6 1 Monitoring Video Layout Monitoring p 39 for details Layout Sequence Displays the registered layout sequences You can monitor video from multiple cameras sequentially in more than one predefined layout Refer to 6 1 Monitoring Video Layout Sequence Monitoring p 40 for details Camera Sequence Displays the registered camera sequences You can monitor video from multiple cameras sequentially in the same camera screen Refer to 6 1 Monitoring Video Camera Sequence Monitoring p 43 for details Map Displays
23. if the setup file is available for the devices Select devices and click the Apply button at the bottom to apply the change rading Device ftwar If you have an upgrade file selecting Firmware Upgrade from the device menu allows you to upgrade the device s software remotely You can upgrade software of several devices at the same time Clicking the Multiple Firmware Upgrade button above the Site panel displays the following screen Hule Formare Upgrade Click the DI button at the top right corner and ibiza i Sica select an upgrade file If the device is a ee R ZS PC based DVR check the PC Based DVR box and click the DI button The list of available devices is displayed Selecting Show all devices displays all registered devices Select devices and click the Upgrade button at the bottom to start upgrading Editing In Device Information Click All Devices in the Site panel and then the arrow button Se beside each device name in the Site List panel Click the input output device in the list of video in alarm in out and audio in out supported by the device Clicking the LF button at the bottom of the Site List panel or clicking the right mouse button and selecting Edit Device from the menu displays the Edit Device window 22 iRAS Remote Administration System Name Preview Video Device Name Edit the name of the input output device You can use the same name for more than one input output device
24. that controls monitoring of live video and playback of recorded video from devices Remote monitoring of live images from devices Notification of events detected at devices and remote monitoring of the event detected video Panic recording of monitored images Remote software upgrades and system setup Display of device s system log information Map monitoring of live images Decompression algorithm for H 264 MPEG 4 and M JPEG Enhanced security using the SSL function Two way audio communication NOTES In this manual the device refers to a network camera network video transmitter or digital network video recorder DVR NVR This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssi org The software included in this product contains some Open Sources You may obtain the complete corresponding source code from us See the Open Source Guide on the software CD OpenSourceGuidel OpenSourceGuide pdf or as a printed document included along with this document User s Manual iRAS Remote Administration System Chapter 2 Installation 2 1 Product Information Package Contents e Installation CD e User s Manual System Requirements Recommended Requirements e Operating System Microsoft Windows 7 64 bit Home Premium Professional Ultimate Microsoft Windows 8 Pro Enterprise compatible e CPU Intel Core i5 3570K 3 30 GHz or faster e RA
25. the device e Map Link Sets the properties of the map link Name Sets the name of the map link The name will be displayed on the map link X Coordinate Y Coordinate Width Height Sets the position and size of the map link You can also sets the position and size by using the mouse drag and drop on the canvas Text Color Background Color Sets the text color and background color of the map link Opacity Sets the opacity of the background color of the map link Align Text Aligns the name text of the map link Information Displays the map name e Text Box Sets the properties of the text box Text Sets the text The text will be displayed on the map 73 User s Manual p Font Font Size Sets the font and font size Text Color Background Color Sets the text color and background color of the text box Align Text Aligns the text Bold Italic Underline Strikethrough Makes the text bold italicizes the text underlines the text draws a line through the text X Coordinate Y Coordinate Width Height Sets the position and size of the text box You can also sets the position and size by using the mouse drag and drop on the canvas h n It allows you to set up a path sequence and monitor video from multiple cameras sequentially in the same camera screen during map monitoring A path sequence should be set up for each camera on the canvas for path sequence monitoring Click th
26. the selection If you Image Processing gt want to exit the current item setting press the Menu button and releases Motion Object Search the selection Aspect Ratio Save Still Image Remove 8 Refer to 12 4 Network Keyboard Buttons Buttons for RAS System Control p 79 for the explanations about other functions 12 4 Network Keyboard Buttons The following is an explanation of the network keyboard buttons used to control the RAS system Refer to the network keyboard user s manual regarding buttons for PTZ control Buttons for Operation Commands Bu De n on e ID MON PANE DEV DEVI Selects a monitor camera screen panel Number 1 to 9 tab or iRAS system to control ei Numero e Does not function as a command button Shift SHIFT gt Button Performs the secondary function for buttons that o two functions ese eE e ESC Cancels a command during its operation 78 iRAS Remote Administration System Connection e RAS system ID gt Connects to the iRAS system Disconnection e SHIFT amp Releases the connection to the RAS system Panel Tab e TabID gt Selects the panel tab e Camera Screen ID PANE Selects the camera screen e Monitor ID Selects the monitor e Releases the connection of the currently selected camera screen or device e Fl Displays monitor ID when using more than one monitor e F7 SHIFT amp F3 Displays or hides th
27. to search Search Starts searching log entries based on search conditions Full Screen Displays the Report panel in full screen format e E Export Exports the searched log entries as a text file txt or a CSV file csv System and service log entries can also be exported as an encrypted HTML file html which will ask you to enter a password to view the file e B Print Prints the searched log entries e More Displays more results 70 iRAS Remote Administration System Chapter 11 Map Editor You can register a map to monitor video from cameras event detection and input output device s status of devices registered on the RAS program on a map on the RAS system 11 1 Registering Map 1 Go to the System menu Select IRAS Setup Select Device 2 Click Map in the Site panel and then the F button at the bottom of the Site List panel on the right The Map Editor window appears Name 3 Select an input output device connected to a device or a sub map in the Site panel and drag and drop it on the canvas 4 Set up the map Refer to 11 2 Setting up Map p 72 for details 5 Entering a map name and clicking the OK button completes registration of the map 71 User s Manual LI 255 255 255 Original Ratio Site Displays a list of registered devices and map You can search for a registered device and map by entering text beside the H icon Entering text th
28. up the position of side panels and the position of the root map list in the Map panel Live Default Playback Default Map Default The default screen formats for the Live Play and Map screens are displayed Clicking the Format Setup button allows you to change the default screen format Change the screen format based on the selected camera Displays video from a camera selected from the current screen format in the first camera screen of the new screen format when you change screen formats iRAS Remote Administration System 5 6 Screen Displa Display OSD Opacty cf E OSD Magnification H Display Text Border always Live y Camera Title Title Bar M Status Icon PTZ M Date E Time Event Alert I Motion Block H Site Name Text In Message Event Alert Owel Time EMOS sec Playback Camera Title I Title Bar Status Icon Date Time H Site Name Text In Message Position Control ToolBar Opacity eZ e Display OSD Sets up the OSD display setting and information to be displayed on a camera screen The Opacity slide bar allows you to adjust the opacity of OSD On Screen Display Checking OSD Magnification box changes the OSD size depending on the screen size Checking Display Text Border always box puts a black border on the texts of text OSDs such as a camera title date etc See below about OSD information le Camera Title Displays the camera name set in the iRAS program Title Bar Separates the title display
29. using the RTP protocol depending on the network environment Select whether or not to display the broken frames in Live or Play panels Buffering Frame Count Set up the number of buffering frames to use for the RTP protocol The higher the number is the less the video stutter The lower the number is the higher the real time monitoring 33 User s Manual Use Network Keyboard Allows you to control the RAS program by using a network keyboard Set up the port number that the RAS program will use when it is controlled by a network keyboard Selecting Use large mouse cursor enlarges the mouse cursor size Map Setup I Activate Auto Focusing Focusing Event v L O v SOO E O Focusing Duration Focus Minimum Dwell Zoom Finder Map Event Spot Event monitoring dwell Minimum monitoring dwell Instant Viewer Duration Activate Auto Focusing Enlarges the area where the event detected device is placed when an event 1s detected Focusing Event Select a desired event for auto focusing Focusing Duration Set up the duration for auto focusing to last Focusing Minimum Dwell Set up the duration for auto focus to last for the first detected event when events are detected in more than one device consecutively Auto focusing moves to the later detected event after the preset time expires e Zoom Finder Displays or hides the PIP screen The rectangle in the PIP screen indicates the enlarg
30. your system try each level until the image displays properly Screen Size Changes the screen size of the player program Aspect Ratio Changes the image aspect ratio displayed on each camera screen OSD Setup Selects options to be displayed on the screen Enable Audio Plays audio while playing back recorded video that has recorded audio 1x1 screen format only Anti Aliasing Screen Enhances image display quality on the screen by smoothing stair stepping aliasing effects in the enlarged image If video plays slow because of your CPU s slow speed releasing the Anti Aliasing Screen option might improve playback speed Play Speed Control Drawing Mode Ej Saves the current images Save as Image Save as Image Saves the current image as a bitmap or JPEG file Save as Image Actual Size Saves the current image as a bitmap or JPEG Save as Video file in its actual size 1x1 screen format only Save as Video Saves video of desired time range as an AVI file Selects the image size option to enlarge the image or display the image in its actual size 1x1 screen format only You can move the enlarged image by clicking the left mouse button and dragging Displays the image in the full screen O Q Is displayed at the bottom right corner of the screen amp indicates that the clip file has not been tampered with and Q indicates that the system has detected tampering and playback stops Export
31. Export Print Exports or prints images or lists displayed on the panel on the selected tab not supported for all panels RAS Setup Allows you to change the basic settings of the RAS program Refer to Chapter 5 Setup p 17 for details Login Logout Logs in or logs out the iRAS program Lock Locks the iRAS program When the iRAS program is locked you cannot operate the iRAS program Entering a password releases the lock Exit Exits the iRAS program Logout Lock Ctri Alt L e Exit View D iRAS Remote Administration System admin Live 1 O Save to User Layout Saves the current screen format e Full Screen Displays the selected Live or Play panel in full screen format System View Playback About Full Screen Alt Enter Full Screen ToolBar Ctrl Alt Enter Ctrl F Ctrl Ctrl Screen Format Show Previous Cameras Show Next Cameras Set Hotspot Set Event Spot Full Screen Toolbar Displays the selected Live or Play panel in full screen format with a panel toolbar Screen Format Allows you to change the screen format Show Previous Cameras Show Next Cameras Moves to the PI iRAS Remote Administration System admin Live 1 Inside o 14 Set Map Event Spot previous or next camera group e Set Hotspot Sets up a selected camera screen as a hotspot screen Refer to 6 1 Monitoring Video Hotspot Setup p 38 for details Ctrl Alt E Emergency Event Panel Set
32. M 4GB or more e VGA ATI Radeon HD 7700 or NVIDIA GeForce GTX650 or higher 1280x1024 32bpp or higher multi monitor e Hard Disk Drive 6 GB or more free space e LAN Gigabit Ethernet or faster Minimum Requirements e Operating System Microsoft Windows XP Home SP 3 e CPU Intel Core 2 Duo E7200 2 53 GHz or faster e RAM 1 5 GB or more e VGA ATI Radeon HD 2400 or NVIDIA GeForce FX5500 or higher 1024x768 24bpp or higher e Hard Disk Drive 1 GB or more free space e LAN 10 100 Mbps Ethernet or faster NOTE The iRAS program operates under 32 bit operating system When you install it under 64 bit of Microsoft Windows Vista or later operating system it is installed and operates in 32 bit compatibility mode 2 2 Installation NOTE Disable your PC s Windows power saving function Start menu Power Options set both Turn off the display and Put the computer to sleep to Never Power Options Power Schemes tab set both Turn off monitor and Turn off hard disks to Never when using the Microsoft Windows XP operating system CAUTION If an older version of iRAS software is installed on your computer a screen appears asking you to upgrade the software In this case you are required to upgrade the software according to the instructions in the screen 1 Insert the software CD in the PC 2 Run the setup exe file in the Setup folder of the software CD NOTE The User Account Control window might app
33. NC Virtual Network Computing remote connection Port E password MM e Port Password Enter a port number and password E Scale to window size set in the device for VNC remote connection Auto Reconnect e Scale to window size Scales the VNC Viewer screen to fit window size Auto Reconnect Reconnects automatically when the VNC remote connection is released Detailed Information It displays the device s registration information Information Detailed Information e Group Service Displays the list of device groups ami and services that the device is registered on e Device Type Displays the device type Description hanging Device ing Remotel Selecting Remote Setup Device from the device menu allows you to change the device s settings remotely Changing the device s settings remotely might not be available for some settings Refer to the device s user manual for details about the settings You can change settings of several devices at the same time using a setup file Clicking the 4 Multiple Remote Setup button above the Site panel displays the following screen 21 User s Manual POD METAS sori J Click the DI button at the top right corner and Diii select a setup file The list of available devices AA des sa is displayed This function might not be n uu supported depending on the device model and the devices that this function is not supported for will not be displayed in the list even
34. The event spot screen is surrounded by a blue outline 3 When an event is detected video from the event detected is displayed on the event spot screen CAMS gt An eventis detected gt 38 iRAS Remote Administration System Map Event Spot Setup NOTE The map event spot in the RAS program is a predefined camera screen in which video from a camera which an event is detected among cameras on a map can be monitored with emphasis The map event spot screen is surrounded by a gray outline 1 Select a camera screen to set up as a map event spot screen on the current monitoring screen 2 Click the Ed Map Event Spot button on the toolbar at the bottom of the Live panel and the current connection in the selected camera screen is released The map event spot screen is surrounded by a gray outline 3 When an event is detected video from the event detected is displayed on the map event spot screen 3 CAM CAM CAM 4 5 6 ge CAM Map CAMS CAM3 gt An event is detected gt a 4 5 6 3 CAM CAM CAM 4 5 6 Layout Monitoring You can monitor video from multiple cameras in a predefined layout A layout should be registered on the RAS program for layout monitoring Refer to the following explanation for details about layout registration NOTE A layout in this manual refers to a screen organization created by arranging specific cameras in a specific screen format Select a desi
35. The playback speed varies with the amount the ring is turned fast forward and rewind e Controls the playback speed when playing back video recorded in devices 80 iRAS Remote Administration System Appendix OSD Information The OSD On Screen Display is displayed in each camera screen in the Live screen of the RAS program CAM1 STE a i 4 P e Camera Title Indicates the camera name set in the RAS program upper left corner of the screen y M e Listen or Talk Indicates the RAS system can receive audio from or sends n E te audio to the val upper right EE of the SESCH NE Ss P PTZ Indicates PTZ control is enabled upper right corner of the screen I EES e T Camera Sequence Indicates the cameras are being sequenced upper right 2009 06 04 18 02 02 corner of the screen e Orange Is displayed during Panic Recording Indicates video is being recorded in the iRAS system upper right corner of the screen e Zoom In Indicates video is zoomed in upper right corner of the screen e Color Control Indicates the color control function is used playback video only upper right corner of the screen e Image Effect Indicates the image effect function is used upper right corner of the screen e Freeze Indicates images on the screen is frozen by a network keyboard live images only upper right corner of the screen e Date Time Indicates the d
36. Z camera moves M to the position of the selected Preset Zoom Control Clicking the Image Zoom button on the control toolbar allows you to zoom in on the current video NOTE PIP is an abbreviation of Picture in Picture and describes a smaller screen within a screen Dragging the mouse on the camera screen moves the zoomed in area o Slide Bar Adjusts the enlargement ratio You can adjust the enlargement ratio also by using the mouse scroll wheel e La Actual Size Zoom Enters the actual size zoom mode In the actual size zoom mode the image is displayed in its original size regardless of the camera screen size or image s aspect ratio e Zoom Finder Displays or hides the PIP screen The rectangle in the PIP screen indicates the zoomed in area 48 iRAS Remote Administration System Image Effect Clicking the Fx Image Effect button on the control toolbar displays the image effect control toolbar and allows you to control image effect This change will be applied to only the video of the iRAS program and not to the device e gt Blur Blurs the image to reduce noise 2 Sharpen Sharpens an image di High Boost Increases the brightness and contrast of images Histogram Equalization Equalizes the image brightness to make it more natural El Edge Detection Extracts the image edge Ca Revert Cancels the adjustment and reloads the original image Text In Viewer C
37. age EEE O E Auto run iRAS at Windows startup i Auto Connect E Auto login at startup LJ E Auto Date Time Date Time 2012 10 31 17 28 24 pate Format SSSA e Language Select the language in which to run the iRAS program The change will be applied the next time the program is run 27 User s Manual Auto run RAS at Windows startup The RAS program automatically runs when logging onto Windows CPU Usage Popup An alert message will pop up when the CPU usage of the RAS system exceeds the assigned percentage Auto login at startup The RAS program automatically logs in with the login information from the previous connection when it starts Checking the Restore last Live sessions at auto login box restores the previous live monitoring sessions in the current Live panels Auto The RAS program automatically logs out or the RAS system is locked out depending on the setting when there are no mouse or keyboard inputs for the specified time Date Time Displays the current date and time Date Format Time Format Set up the system date time format Start Week On Set up the day of the week to start 5 5 Screen Format 28 General Side Pane Position Map Sitemap Position Screen Format Live Default Format Setup Playback Default Format Setup Map Default Format Setup M Change the screen format based on the selected camera Cancel Side Pane Position Map Sitemap Position Set
38. anel Clicking the OK button completes the device group registration 5 Check that the device was added to the device group correctly Click Device Group in the Site panel and then the arrow button Bai beside Device Group Clicking the registered group displays the list of devices added to the device group in the Site List panel a Group Address Type Description Selecting the registered device group and then the LT button at the bottom of the Site List panel displays the Edit Device Group window and allows you to edit the selected device group Refer to 5 1 Device Managing Devices p 18 for details 3 3 Live Video Monitoring Yo AARARARRARAARARO 2 Click the Live tab on the tab panel Select a site to connect MN SEO STE to from the Site list and drag and drop it on the Live screen sen i es pn Live video from the selected site is displayed on the screen Refer to Chapter 6 Live Video Monitoring p 37 for details Live 1 10 iRAS Remote Administration System Recorded Video ARRAAARARRARARAD 2 Click the Play tab on the tab panel Select a site to connect HA to from the Site list and then drag and drop it on the Play i i i er screen Recorded video from the selected site is displayed gt on the screen Refer to Chapter 7 Recorded Video Playback amp Exportation p 53 for details 11 User s Manual 12 iRAS Remote Administration System Chapter 4
39. area from an image display area at the top Status Icon Displays status OSD Orange During Panic Recording P In the PTZ mode In the zoom mode J During camera sequencing CP During two way audio communication 3 When the color control function is used playback video only Fi When the image effect function is used When images on the screen is frozen by a network keyboard live images only PTZ Displays direction control buttons which is displayed on the camera screen when controlling a PTZ camera Le Date el Time Displays the date and time of the RAS system Le Event Alert Event Alert Dwell Time Highlights the camera title bar in red when an event occurs in the device The alert will release after the event dwell time sec from the time an event is detected or when you select the camera screen if you set up the Event Alert Dwell Time setting to Manual Off Motion Block Displays the area where motion is detected with red blocks when a motion detection event occurs in the device supported only for network video transmitters le Site Name Displays the device name This will be displayed only when the device name is different from the camera title Le Text In Displays the text in information on the screen when a text in event occurs in the device 1x1 screen format only Le Message Displays a screen message Refer to 5 10 Network p 33 for details about the sc
40. at you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found As you enter more text the results narrow 1 Canvas Allows you to create a map by inserting a background image and placing input output device icons or map links from the Site list Setup Buttons Sets up the map Align Aligns the input output device icons or map links on the canvas M Text Box Inserts a box which allows you to enter text Mi Path Sequence Sets up a path sequence Refer to Path Sequence p 74 for details El Synchronize Map Objects Name Synchronizes the input output device s name based on the settings in the device El Background Image Inserts a background image on a canvas El Status Color Sets up a unique color for each event detection or status of input output devices EI Delete Selecting an input output device icon or a map link on the canvas and clicking this button deletes the icon or link from the canvas Property Sets up the property of the map canvas input output device icons or map links Event Action Sets up the event action of the input output device icons When you monitor video on the map and events are detected notification on the map is made based on the event action settings Icon Alignment You can adjust the alignment on the canvas and size of one or more input output device icons or map links
41. ate or time of the RAS system bottom of the screen e Event Alert Indicates an event detected highlights the camera title bar in red e Motion Block Indicates a motion event detected in the boxed area on image supported only for network video transmitters Troubleshooting Montesa Check that devices have been added to a device group e Check that you have authority for monitoring The connection was released during monitoring and the Check the device status and the network connections for the device and RAS system repeats IRAS system reconnecting e Check the camera connections in the device e Video display might lag because of system or network congestion e Check if the Device Real Time Monitoring option is enabled If it is disabled event related functions are supported only for the devices that are currently monitored No live video Event function does not work 81 User s Manual e Check the speaker and microphone connections in the device and the IRAS system e Check the audio input and output settings of the device e Two way audio communication is one to one communication If the device is already in audio communication with another system try again when the other audio communication is disconnected Two way audio communication is not available Cannot operate the iRAS program because of wrong ID and password e Uninstall and reinstall the RAS program You must delete
42. can adjust the enlargement ratio also by using the mouse scroll wheel e Lal Actual Size Zoom Enters the actual size zoom mode In the actual size zoom mode the image is displayed in its original size regardless of the camera screen size or image s aspect ratio e E Zoom Finder Displays or hides the PIP screen The rectangle in the PIP screen indicates the zoomed in area Image Effect Clicking the Fx Image Effect button on the control toolbar displays the image effect control toolbar and allows you to control image effect This change will not be applied to the recorded video e Blur Blurs the image to reduce noise e Sharpen Sharpens an image e A High Boost Increases the brightness and contrast of images e Histogram Equalization Equalizes the image brightness to make it more natural e El Edge Detection Extracts the image edge e Es Revert Cancels the adjustment and reloads the original image You can export recorded video to USB devices Click the J Export Video File button on the toolbar at the bottom of the panel and the export menu is displayed gt JE A B Export Video File Export Video File Reserved Self Player 58 iRAS Remote Administration System e A B Export Video File Sets up the section of video to be exported by using the timetable Select A B Export Video File from the export menu Click the starting point in the timetable and drag to the ending point
43. creen format for each layout sequentially Site 2 Clicking the Ed Layout Sequence button of the toolbar at the bottom of the panel stops or starts the layout sequence Example CAM CAM 4 2 CAM 5 3 3 4 4 5 6 Layout 1 Layout 2 cam 5 LZ cam 5 LZ CAM CAM 3 3 EEE CAM CAM CAM CAM CAM CAM 4 5 6 4 5 6 Layout Sequence Registering L n 1 Go to the System menu and click RAS Setup and select the Device menu 2 Click Layout Sequence in the Site panel and then the button at the bottom of the Site List panel on the right The Add Layout Sequence window appears 3 If no layout to be sequenced is registered click the Add Layout button The Add Layout window appears Register layouts to sequence referring to Layout Monitoring p 39 At least two layouts must be registered for sequencing 41 User s Manual 42 Selected Layout Sequence List Duration sec Apply all Layout Duration sec e Name Enter the layout sequence name e Public Private Displays the layout sequence to all users Public or to a current user only Private The admin user can see all layout sequences e Owner Displays the user ID of the person who created the layout sequence e Layout List Displays a list of registered layouts You can search for a registered layout by entering text beside the H icon Entering text that you want to search for causes the search results to be displayed Search results
44. deo from the event detected camera is displayed on the event spot screen when an event is notified in the Instant Event list Event monitoring dwell Set up the duration for video to be displayed on the event spot screen Minimum monitoring dwell Set up the event monitoring dwell time for the current event when other events are detected while event detected video is displayed Video from other events is displayed after the preset time expires 32 iRAS Remote Administration System General Il Use buffering for live Mega pixel images Live image no frames detect interval INotUse el Disconnection Message DVRNS Use FEN Service e effect unti the svetem is restarted RTP Incoming Port Range om Es 17999 S Don t display broken frames I Live H Playback Buffering Frame Count 3 RA Network Keyboard MM Use Network Keyboard Control Port Use buffering for live Mega pixel images Displays images on the screen more smoothly by using buffering when monitoring mega pixel video images Buffering may be delayed or real time monitoring may decrease depending on the network environment This function is supported only in a dual core CPU or higher systems for up to four cameras in each Live panel e Live image no frames detect interval Set up the interval to check video frame transfer from a device to the RAS system A message will be displayed on the camera screen when no video frame is transferred durin
45. dministration System e Remove Disconnects the current connection Snapshot on Motion Event Clicking the Snapshot on Motion Event button on the panel toolbar displays snapshot of images recorded during the event based recording event and pre event in the Play panel The timetable displays the recording information of the selected snapshot Clicking anywhere on the recorded data in the timetable displays a snapshot of the selected time Hovering the mouse cursor over each snapshot displays a popup viewer screen above the snapshot Cesa e Use Popup Viewer Enables display of the popup viewer screen Close Object Motion Search Clicking the amp Object Motion Search button on the control toolbar displays the object motion search panel at the bottom and allows you to search for changes or motion in recorded images in the device or the RAS system e E Draw Search Zone Allows you to define the area to search for changes or motion on the camera screen by dragging the mouse The search zone is displayed with red blocks e Erase Search Zone Allows you to erase the search zone set on the camera screen by dragging the mouse e B Set Ref Image Sets the image currently displayed on the camera screen as a reference image for change detection Object Search only View Ref Image Displays or hides a PIP screen with the reference image Object Search only Find Method Date Time Se
46. e RAS Setup screen Function 1 to 8 System menu RAS Setup e ES SHIFT amp EA Displays or hides the RAS program s software version Buttons for RAS System Control NOTE Some functions may not be supported depending on the connected device Panic Recording On e Camera Screen ID _ Starts panic recording for the selected T camera screen Panic Recording Off Camera Screen ID SHIFT amp Y Stops panic recording for the selected camera screen e Camera Screen ID gt Activates the alarm out 1 of the device Alarm Out On connected to the selected camera screen e Alarm out device No gt Activates the selected alarm out e Camera Screen ID gt SHIFT amp Deactivates alarm out 1 of the device connected to the selected camera screen Alarm Out Off e Alarm out device No SHIFT amp Deactivates the selected alarm out Allows you to change a screen format Select a screen format Bisel by using arrow buttons and enter button ES e SHIFT amp E3 Changes to the 1x1 screen format Pressing the button again returns to the previous screen format Moves to the next camera group Freeze Freezes the current live images on the screen e SHIFT amp Zooms in the current live images on the screen You Zoom can move the zoomed in area by using arrow buttons and enter button Full Screen e Panel tab ID gt Displays t
47. e W Path Sequence button Click each camera icon on the canvas in order of monitoring Click the right mouse button to finish the setting General Name Path Sequence 1 Color MN 50 100 255 Opacity 70 Width 5 Shape Ellipse Background Color J 0 0 255 Opacity 63 Margin ZA AA Reverse Associated Device CAM1 Disconnect Duration 10 CAM2 Duration 10 Event Action Name Sets the name of the path sequence Color Opacity Width Sets the color opacity width of the path displayed on the map Shape Sets the shape of the alert icon to distinguish a camera when displaying video from a camera set for the path sequence during map monitoring Background Color Opacity Margin Sets the color opacity margin of the alert icon when displaying video from a camera set for the path sequence during map monitoring Reverse Reverses the direction of the path sequence Associated Device Displays the list of cameras set for the path sequence Video from cameras in the list is displayed on the screen sequentially for the Duration period Clicking a camera in the list and the Disconnect button deletes the camera from the path sequence Y ou can set up event actions to be taken when events are detected by the input output devices Select the icon and then each field of the property You can enter or select a value from the drop down list 74 Event Action Click Instant Viewer Use Motion Detection Live Popup Event Sp
48. e enabled in the device Alarm In Displays the status of alarm in devices that are enabled in the device Recording Displays the recording status Recording Check Displays the recording check status Rec From To Displays the recording period 67 User s Manual 9 2 Status Monitorino Device status monitoring is supported in the Status panel If the Status tab is not on the tab panel go to the System menu click New Tab and Status Remove a e on System admin tatus Export Ctrl E Playback About Print Ctrl P Status iRAS Setup Login Logout Lock Ctri Alt L Exit Select a device to connect to from the Site list and drag and drop it on the Status panel The status of the selected device is displayed linistration System admin Status Playback About Status Version 22 0 13 14 15 Alarm Out System Check e Status Display Window Displays the status as icons Camera Displays the camera numbers Version Displays the system version information Event Displays the status of event detection When an event is detected the icon is displayed in corresponding color Hovering the mouse cursor over an icon displays the event type in a tooltip Alarm Out Displays status of the alarm out signals System Check Displays the function status of the device and recording e Function Buttons Ba Disconnect Disconnects the current connection on the
49. e mode is enabled the RAS system records over the oldest video data once all available storage space has been used When overwrite mode is disabled the RAS system strops recording once all available storage space has been used e Clear All Recorded Data Deletes all recorded data in the RAS system e Reconstruct Abnormal Recorded Timetable When any error occurs during recording the recorded data and the timetable information of the recorded data might not match and the timetable in the RAS program might display incorrect information In this situation clicking the button reconstructs the timetable to display recorded data correctly on the timetable in the iRAS program Overwrite recorded data when the disk is full Records over the oldest video data once all available storage space has been used e Use Panic Recording Enables panic recording Storage Path Allows you to set up the storage folder path for panic recording Capacity Sets up the storage capacity to be allocated to the hard disk drive Min 4GB to max 64GB You can do panic recording as follows Select a camera screen on the Live screen on which video to record is displayed and click the 9 Panic Recording button on the control toolbar The Panic Recording OSD is displayed at the top right corner of the camera screen and the system starts recording Clicking the Panic Recording button again stops recording 5 4 System General Langu
50. e proper stream based on the screen format Interactive Bandwidth Control Controls the network bandwidth by automatically adjusting the resolution and the frame rate of the device depending on a screen format 1x1 screen format the maximum resolution and frame rate supported by the device Multi screen format the resolution and frame rate decreased to an appropriate level for each screen format This function enhances the network bandwidth efficiency and decreases a drop in performance of the RAS system which might be caused by the network congestion For this function to work the device must be also set up to use the function This function works only for monitoring video Use H W Acceleration Enables hardware acceleration in the iRAS program It may enhance processing of HD high definition video This option is available only when hardware acceleration is enabled in your PC 5 8 Report Log List Number of results displayed on the list wo o Health Use Health Update Interval 30 minutes e Number of results displayed on the list Set up the number of log entries to be displayed at once in the case of Device Log maximum 100 logs at once regardless of the setting 31 User s Manual e Health Set up the status update interval in the Health panel Selecting the Use Health box enables or disables the Health panel 5 9 Instant Event Instant Event Time Range en Lee Minutes Instant Event li
51. ear when using the Microsoft Windows Vista or later operating system Click Allow and install the software following the instructions User s Manual 3 Select the language in which to run the program and then click OK f Language Selector NOTES e To properly display the selected language your PC s operating system should be set to support the selected language e To change the RAS program s language after the software has been installed run the RAS program Go to the System menu Select RAS Setup Click System 4 When the following screen appears click Next GU Welcome to the iRAS Setup Wizard The installer will guide you through the steps required to install RAS on your computer WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law 5 Designate the folder path to install the program IRAS Select Installation Folder The installer will install iRAS to the following folder To intall in this folder dick Next To install in a different folder enter it below or dick Browse Folder 6 When the following screens appear click Next Confirm Installation Installing iRAS The installer is ready to install iRAS on your computer RAS is being installed Click Next
52. ed Deinterlacing Enhances image display quality of interlaced video on the screen by eliminating horizontal scan lines or noise in areas with motion Select the desired deinterlace filter Anti Aliasing Enhances image display quality of video on the screen by eliminating stair stepping aliasing effects in the enlarged image 30 iRAS Remote Administration System Important Video Performance Gives priority to display speed over the display quality on the screen when displaying video Trim The Black noise Edges Trims the black line noise displayed at the edge of the image Improve Tearing Artifacts Improves tearing artifact caused when the monitor s scanning line retracing speed is slow 1x1 screen format only This might increase the CPU load Disable Transparent Window Disables using a transparent window style and opacifies windows including the control toolbar to correct the problem of transparent areas of the window flickering The change will be applied the next time the program is run Disable Desktop Window Manager DWM Disables Desktop Window Manager DWM that runs Windows Aero Disabling DWM is recommended if video often freezes when multiple monitors are used Dynamic Multistream Control Allows you to use a different stream depending on the screen format supported only for devices in which more than one stream is used Selecting Auto allows the iRAS program automatically to choose th
53. ed area When set to Auto the PIP screen is displayed only while a canvas is enlarged e Map Event Spot Video from the event detected camera is displayed on the map event spot screen when an event is detected Event monitoring dwell Set up the duration for video to be displayed on the map event spot screen Minimum monitoring dwell Set up the event monitoring dwell time for the current event when other events are detected while event detected video is displayed Video from other events is displayed after the preset time expires Instant Viewer Set up the duration for the instant view to be displayed Instant Viewer is displayed when clicking a camera on a map 34 iRAS Remote Administration System 5 12 Backup Restore It allows you to save the setting values of the RAS program as an iexp file or to apply the saved setting values to the current iRAS program 35 User s Manual 36 iRAS Remote Administration System Chapter 6 Live Video Monitoring You can monitor live video of each group The iRAS system displays video from devices based on the settings in the device on the Live screen 6 1 Monitoring Video Live video monitoring is supported in the Live panel maximum 4 If the Live tab is not on the tab panel go to the System menu click New Tab and then Live Remove gt ArT Export Ctrl E Playback Print Ctrl P RAS Setup gt Logout Lock Ctrl Alt L Exit
54. ences Clicking a layout sequence in the list and dragging and dropping it on the screen starts layout sequence monitoring Refer to 6 1 Monitoring Video Layout Sequence Monitoring p 40 for details Camera Sequence Displays the list of registered camera sequences Clicking a camera sequence in the list and dragging and dropping it in the desired location on the screen starts camera sequence monitoring Refer to 6 1 Monitoring Video Camera Sequence Monitoring p 43 for details Map Displays the list of registered maps Clicking a map in the list and dragging and dropping it in the desired location on the screen starts map monitoring Refer to 6 2 Map Monitoring p 44 for details HDP Displays the list of device s removable eSATA hard disk drives or SD SDHC memory cards connected to the iRAS system A SATA or IDE to USB 2 0 Converter is needed to connect the removable hard disk drive to the iRAS system an eSATA cable for the eSATA hard disk drive and an SD SDHC memory card reader for the SD SDHC memory card Ask your dealer or distributor for details Clicking the right mouse button in the list displays the storage information folder path drive type device model recording period storage capacity etc Panic Record Displays the list of devices if there is any device for which panic recording has been done 15 User s Manual Panel e Live Displays live images Refer to 6 1 Monitoring Video p 37 for detai
55. ent detected device is placed when any event is detected When events are detected in more than one device at the same time the canvas is enlarged as much as possible while still displaying all event detected devices When events are detected in more than one device consecutively the focusing moves to the later detected event after the preset time expires Refer to 5 11 Map p 34 for details about the auto focusing setting e Focusing Event Allows you to select a desired event for auto focusing e lal Actual Size x1 Displays a map in its original size regardless of the map screen size or canvas s aspect ratio e 5 Zoom Finder Displays or hides the PIP screen The rectangle in the PIP screen indicates the enlarged area When set to Auto the PIP screen is displayed only while a canvas is enlarged Zoom In Allows you to adjust the enlargement ratio of the canvas Example e When Zoom Finder is set to Off Map Monitoring Event Detection Auto Focusing e When Zoom Finder is set to Auto or On Map Monitoring Event Detection Map Screen Menu The screen menu is displayed when selecting a map screen and clicking the right mouse button The screen menu allows you to control the selected map 50 iRAS Remote Administration System Previous Next Auto Focusing Actual Size x1 Zoom Finder Zoom In These function the same as clicking the individual buttons on the control toolbar Refer to Control
56. enu click New Tab and Live Remove wer _ tem admin Live 1 Export Print RAS Setup Logout Exit 64 Lock Ctrl Alt L Ctrl E Ctrl P gt Playback About Live 1 1 iRAS Remote Administration System Click the Live tab in the tab panel Select a desired event nas Remote Administration System admin Live 1 Inside 1 System View Playback About from the event list and drag and drop it on the Live screen E e S gt Site Live video from the camera where the selected event occurred 1s ci ee displayed on the screen ae Sica Playing Video Playing event recorded video is supported in the Play panel If the Play tab is not on the tab panel go to the System menu click New Tab and Play Remove Export Ctrl E Playback About Print Ctrl P Play 1 RAS Setup D 1 Logout Lock Ctri Alt L Exit Click the Play tab on the tab panel gt Select a desired event nas Remote Administration System admin Play 1 from the event list and drag and drop it on the Play screen a e i The event recorded video is displayed on the screen Site Play 1 65 User s Manual 66 iRAS Remote Administration System Chapter 9 System Health amp Status Monitoring You can simultaneously check the system status and device status of registered devices 9 1 Health Monitorino System health monit
57. g the period e Disconnection Message Allows you to change the text of the screen message displayed when a device is disconnected or when you connect to the device Click the Setup button check the box beside each message and change the text e DVRNS Allows you to enter information of the DVRNS server on which a device is registered if there is a device that uses DVRNS DVR Name Service function If this setting is not correct registration of the device and connection to the device will not be made If a device to connect uses FEN For Easy Network service selecting the Use FEN Service option makes the DVRNS server operate as a FEN server to enable FEN service to work and the iRAS system connects to the device by using FEN service When FEN service works it might not be supported to connect to the device using the VNC Virtual Network Computing function depending on the network connection type e g UDP Hole Punching Relay of the device and iRAS system e RTP Incoming Port Range Set up the port range if a device which transmits images using the RTP protocol is registered Port range settings must be changed if the network firewall or local network allows only specific UDP RTP port numbers The port numbers should not conflict with the RTP port numbers of other streaming programs If an RTP port number conflicts with others monitoring may not be available e Dont display broken frames It is possible that frames will be broken or lost when
58. he hour segments timetable Save Still Image Saves the current image on the screen as an image file at its original size Export Image File Print Image Exports or prints the images currently displayed on the screen Export Panorama Screen Exports the images currently displayed on the screens E Export Video File Exports recorded video as a self player file exe or an AVI file avi Refer to 7 2 Exporting Recorded Video p 58 for details EJ Event on Play Displays the list of events if there is event recorded video among the video that is currently being played back Double clicking an event from the list displays the event recorded video Snapshot on Motion Event Displays snapshot of images recorded during the event based recording event and pre event in the Play panel Refer to Snapshot on Motion Event p 57 for details CA Step Playback Moves the video forward or backward based on the setting displayed between the El and A buttons Clicking the arrow between the D and A buttons allows you to change the interval the video moves KI A Fast Backward Fast Forward Plays back recorded video fast backward or fast forward O MAM Stop Play Stops or plays recorded video on the screen WD Jog Shuttle You can adjust the playback direction and speed by using the jog shuttle The vertical line in the jog shuttle indicates the current playback direction and speed Video is played backward when the vertica
59. he panel tab in full screen format 79 User s Manual Displays the Play panel and allows you to search and play back recorded video of the device connected to the selected camera screen in the Live panel is connected amp Returns to the previous Live panel Fast Backward Play 44 Plays video backward at high speed in the playback mode e SHIFT amp aa Plays video backward image by image in the playback mode e Plays back video Pressing the button while playing back video pauses the video Search Live Backward Step Fast Forward Play Plays video forward at high speed in the playback mode e SHIFT amp Plays video forward image by image in the playback Forward Step ade e Selects an item in the screen menu of the selected camera e Toggles the zoom size when in the zoom mode e Navigates through items in the screen menu of the selected camera Arrow Buttons screen e Moves the zoomed in area when in the zoom mode e Functions only when in the playback mode 5 Jog Dial Plays video forward or backward image by image by turning the jog dial clockwise or counterclockwise when playback video has been paused e Functions only when in the playback mode e Plays video when in the playback mode The shuttle ring is spring loaded and returns to the center position when released Turning Shuttle Ring the ring clockwise or counterclockwise plays video forward or backward
60. he quality Selecting this option enables the Quality setting below e Size Set up the file size for compressing the file Original Ratio Saves images with fitting within the screen size while maintaining their original ratio Fit to Screen Saves images with fitting to the screen size regardless of the aspect ratio regardless of the aspect ratio Fit to Screen Aspect Ratio Saves images with fitting to the screen size keeping the aspect ratio This might cause top and bottom or left and right side of images to be cropped depending on the screen size This aspect ratio is not supported and Original Ratio is applied for camera screens that the following function is activated Image Zoom Anti Aliasing Enhances image display quality for all cameras on the screen by eliminating stair stepping aliasing effects in the enlarged image e Keyframe Sets up the keyframe for compressing the file e Max File Size Sets up the maximum file size Save Split File Exports video by creating multiple files of the Max File Size units set above when the data file reaches the maximum file size If this option is not selected it exports only as much as the maximum file size View Proceeding Frames Displays a popup window showing the video currently being exported Playing AVI File Run the video player program and open the exported AVI file If the codec selected during exporting video as an AVI file is not installed yo
61. he selected pins amount from the time selected on the timetable Gen ca e Self Player AVI Select Self Player abia e Save Password Set up a password for playing ll back the exported video You will be asked to enter H indude Text In Data T H Exclude Player the password to initiate the Player program Hier asse Include Text In Data Includes text in data when saving video 1f the video was recorded with text in data Exclude Player Saves the recorded data without including the Self Player program The file size will be smaller and it will take less time to save but you will need to run the Self Player program ClipPlayer exe which is provided in the iRAS installation folder Client selfplayer to play the saved file This may not be supported depending on the specifications and version of the device Reservation Reserves a time to perform exporting In the reserved time the iRAS system performs exporting with the settings above 59 User s Manual PI in If Player Fil You do not need to install any special software to play video exported as a self player file because the self player file contains a player program Clip Player Double clicking the target file starts the Player program and video is displayed on the screen Clicking the slide bar at the bottom of the Player program displays the playback image of the selected time on the screen Clicking the K button exits the Player program NOTES 60
62. ice s Setting Remotely p 21 for details 17 User s Manual S Network Keyboard Setup Allows you to add remove and edit a network keyboard You can control the RAS program with a network keyboard Refer to Chapter 12 Controlling With a Network Keyboard p 75 for details Site Site Panel Displays site group lists supported by the RAS program See Site p 18 for details Name Group Address Type Description Site List Panel Displays the list and information about sites registered in each group Clicking the arrow button e beside each device name displays information of video in alarm in out and audio in out supported by the device o Incremental Search Allows you to search for a device or site registered in each group Selecting a group in the Site panel and entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found within the selected group As you enter more text the results narrow Add Remove LA Edit Allow you to add remove and edit a device or a site You can also delete sites from the group or to edit registration information by using the menu that is displayed when selecting a site and clicking the right mouse button If you select a device you can connect to it and change its settings or upgrade its software remotely If you delete a device from All Devices and register the device again the
63. ing as an AVI File The recorded video is exported as an AVI file avi 61 User s Manual Export Video File fom Fest ETS ENS 1 Minute 3 Minute 10 Minute 30 Minute 60 Minute O self Player O AVI MEY All Devices MY Info Desk VEN Info Desk MEA Inside 1 Ga CAMI Ga CAMAS via CAMI E CAM2 Il Include Audio Data ON 720 x 480 D1 v Anti Aliasing Ee CR A We Keyframe kc 120 Frames Quality ee VI RT cc 2 000 MBytes Save Split File View Proceeding Frames From To Enter the date and time of video to export Selecting First sets the date and time to the date and time of the first recorded video Selecting Last sets the date and time to the date and time of the last recorded video Clicking the 1 Minute 3 Minute 10 Minute 30 Minute or 60 Minute button increases or decreases the time by the selected amount from the time selected on the timetable Self Player AVI Select AVI Include Audio Data Includes audio data when saving video with recorded audio This option is not available when more than one camera is selected Audio might not be saved properly when the recording speed is set to less than 1 ips Codec Bitrate Quality Set up the desired values for compressing the file Encoding Based on Bitrate Encodes video based on the bitrate Selecting this option enables the Bitrate setting below Encoding Based on Video Quality Encodes video based on t
64. ive Screen Menu p 46 for details Layout gt Clicking the arrow button in the upper right corner displays Monitor alive popup menu The live popup menu allows you to Ignore Live Popup change the popup screen settings e Layout Select the display format of popup screens e Monitor Select the monitor on which popup screens are displayed if you use dual monitors e Ignore Live Popup Select a time span to disable the live popup function regardless of the settings in Map Editor Event property Live Popup action Duration e Disable Time Out Click if you want to close the popup screen manually regardless of the preset duration for the popup screen to be displayed Remove All Deletes the list 51 User s Manual 52 iRAS Remote Administration System Chapter 7 Recorded Video Playback amp Exportation You can play back recorded video or export recorded video to USB devices back Recorded Video 1 Search and playback of video recorded in a device or the RAS system are supported in the Play panel maximum 4 If the Play tab is not on the tab panel go to the System menu click New Tab and then Play Remove gt x x n yn System admin Play 1 Export Ctrl E Map Print Ctrl P Report Health Site Play 1 Status View Playback About RAS Setup AnI 1 Logout Lock Ctri Alt L Exit 2 Click the Play tab on the tab panel Select a site to connect
65. l line is to the left of center and video is played back forward when the vertical line is to the right of center The farther the position is from the center the faster video is played back Clicking the vertical line and dragging it to the desired position on the jog shuttle and holding it plays video at a constant speed Releasing the mouse button causes the vertical line to return to the center position Clicking the MA Play button plays video at normal speed Clicking the EJ Shuttle Lock button and dragging and dropping the vertical line to a desired position fixes the vertical line in that position Jog Shuttle You can adjust the playback speed by using the jog shuttle The vertical line in the jog shuttle indicates the current playback speed EJ Save to User Layout Saves the current screen format oe SEED Screen Format Changes the screen format Clicking the M button displays additional s screen ici Clicking the amp or button moves to the previous or next camera groups iRAS Remote Administration System Tim le Event Li e Time Lapse Search Mode When in the time lapse search mode the timetable is displayed at the bottom of the screen and it displays the recording information for each camera Clicking the A button in the top right corner of the timetable displays the recording information for all cameras Clicking the F button displays the recording information for the selected camera on the screen NOTE The
66. lect IRAS Setup gt Select Device Click E Network Keyboard Setup button and the Network Keyboard Scan window appears The way to register a network keyboard is identical to the way to register a device Refer to 3 2 Registering Devices p 7 about registering a device details Add Video Management System ID H Name Video Management System Connection Ethernet z IP Address Use DVRNS Control Port 8010 UserID Password Cancel Network Keyboard Scan ES le AN Auto Scan LAN Register the RAS system on the network keyboard Refer to the network keyboard user s manual for ID GRAS system ID The network keyboard assigns the ID automatically when the RAS system is registered and you can change the ID The ID is used to distinguish the IRAS system from other RAS systems when controlling 1t with a network keyboard so each must have a unique ID Name Set up aiRAS system name for your reference IP Address Enter the RAS system s IP address Do not check Use DVRNS Control Port Enter the Control port number set in the RAS System Check the Control port number in the System menu RAS Setup Network Network Keyboard setting User ID Password Enter the user ID and password for the connection to the RAS system 75 User s Manual 3 Enable a network keyboard in the RAS system by checking the Use Network Keyboard option Playback About Ne
67. lected the Exclude Playeroption when saving recorded video you must run the Self Player program ClipPlayer exe which is provided in the iRAS installation folder Client selfplayer to play the saved file Entrance Clip Player E Goes to the beginning of the video Goes to the end of the video Et Plays the video in fast reverse id Plays the video in fast forward Ell Goes backward one frame of the video II Goes forward one frame of the video ZI Plays the video at regular speed Shows the previous camera group if there is recorded video in the previous camera group based on the current screen format ER Cycles through the screen formats It cycles through 2x2 1 7 3x3 4x4 4x5 5x5 and 1 32 14 Shows the next camera group if there is recorded video in the next camera group based on the current screen format 3 Sets up the properties of the player program iRAS Remote Administration System Ak Print Prints the current image e Frame Info Displays Channel Title Time Type Size and Resolution information about the image Image Processing Controls brightness blur and sharpness of playback images oe 1x1 screen format only Aspect Ratio Play Speed Control Changes the playback speed Play or fast forward backward OSD Setup playback speed FF RW Y Enable Audio Drawing Mode Selects the draw mode level If you are not sure about the best Stee draw mode level for
68. licking the T Text In Viewer button on the control toolbar displays the text in viewer window and allows you to check the text in data in real time supported only when a text in event is detected The camera title bar is highlighted in blue when a text in event is detected All Attach Clicking the title bar in the Text In Viewer Save As window displays a text in popup menu Time Range 139 70 e All Attach Docks all text in viewer windows in one panel e Save As Saves the text in data as a text file txt e Time Range Set up the length of time for text in data to be displayed when a text in event occurs You can check the text in data in the text in viewer window within the established time range for the event 6 4 Controlling Maps A control toolbar and a screen menu are provided for controlling a map Control Toolbar When selecting a map and hovering the mouse cursor over the map the control toolbar is displayed over that map The control toolbar allows you to control the selected map Hovering the mouse cursor over a button displays a tooltip for the button 49 User s Manual e du Previous Map Next Map Moves to the previous or next connected map of the maps that have been connected to the current map screen Maps can be connected by using map link or by selecting a map from the map list and dragging and dropping it on the current map screen e SIE Auto Focusing Enlarges the area where the ev
69. licking the Do not remove button uninstalls the software without deleting any saved data in the system and keeps all saved data in the system c RAS RAS O Do you want to remove all saved data y iN A tilt Erased data cannot be restored Remove all Do not remove NOTE The deleted data cannot be restored once the data is deleted 5 Click the OK button to complete the uninstall process User s Manual iRAS Remote Administration System Chapter 3 Getting Started NOTE In this manual the iRAS system refers to a PC on which the iRAS program is running and the device refers to a network camera network video transmitter or digital network video recorder DVR NVR After installing the RAS software you will find two shortcut icons 2 of IRAS and RAS Run as administrator on the desktop Double click the RAS or RAS Run as administrator shortcut icon to run the RAS program You should double click the RAS Run as administrator shortcut icon if any device s removable eSATA hard disk drives or SD SDHC memory cards are connected to the RAS system 3 1 Log In You are required to log in as follows when running the program e User ID Password Enter your user ID and password The Enter user 1D and password default user ID is admin and there is no default password You can change the user ID and password in the User menu Refer ver CI to 5 2 User User Management p 24 for details
70. ls e Play Allows you to play back video recorded in a device or the RAS system Refer to Chapter 7 Recorded Video Playback 8 Exportation p 53 for details e Map Displays maps Refer to 6 2 Map Monitoring p 44 for details e Report Displays log entries of the RAS program Refer to Chapter 10 Log Search p 69 for details e Health Displays the results of self diagnostics for the devices in a device group Refer to 9 1 Health Monitoring p 67 for details e Status Displays the status of a desired device in real time Refer to 9 2 Status Monitoring p 68 for details NOTE You can change the panel name by clicking the right mouse button on each panel tab Adding Deleting Panel TI ad Goto the System menu Click New Tab Select a panel to add System View Playback Clicking the Ff button beside each tab deletes the panel Remove Play Map Export Ctrl E Print Ctrl P Report Health Status iRAS Setup gt Logout Lock Ctri Alt L Exit Floating Docking Panel Clicking a panel tab causes it to fly out and dragging it floats the panel on the screen Clicking the tab of a floating panel and dragging and dropping it to its original position docks the panel You can change the order of panel tabs by dragging and dropping with the mouse e Maximizing a floating panel Clicking the window maximize restore button in the upper right corner of the floating panel maximizes or re
71. lts narrow e Add Remove LA Edit Allow you to add remove and edit a user group or user User Management You can assign every user different authority levels for each function of the iRAS program The Administrators group has authority for all functions and the authority settings are not editable 1 Click the button at the bottom of the user group list The Add User Group window appears 24 iRAS Remote Administration System Device Access Authority Authority Description Information Device Access Authority Authority Select List Information Device Access Authority Authority Authority Allow Description e z y e Information tab Enters the user group name e Device Access Authority tab Grants or limits authority for the access to each device e Authority tab Grants or limits authority for each function Clicking the OK button completes registration of the user group 2 Click the added user group in the Group list and then the F button at the bottom of the user list The Add User window appears Administrators Password Confirm Password H No Password I Password Expiration Setup Period Month Email Phone Description 25 User s Manual e Name Enter the user name e ID Password Confirm Enter a unique user ID and password 8 to 16 characters without spaces for access to the RAS program No Password Allows you to log in withou
72. n menu allows you to control the selected camera 46 iRAS Remote Administration System PTZ Control Color Control Image Zoom Image Processing Alarm Out Listen Talk Audio Broadcast MultiStream Hotspot Event Spot PTZ Control Color Control IMage Zoom Listen Talk Panic Recording These function the same as clicking the individual buttons on the control toolbar Refer to Control Toolbar p 46 for details Image Processing Adjusts the image effect Refer to Image Effect p 49 for details Text In Viewer Pops up the text in viewer window supported only when a text in event is detected The camera title bar is highlighted in blue when a text in event is detected Refer to Text In Viewer p 49 for details Audio Broadcast Broadcasts audio to all devices in the current Live tab Alarm Out Activates or deactivates alarm out MultiStream Allows you to choose the desired stream if the device is in the multistream mode for live monitoring Map Event Spot praticit e Hotspot Sets up a selected camera screen as a hotspot screen Refer to Hotspot Setup p 38 for details e Event Spot Sets up a selected camera screen as an event spot screen Refer to Event Spot Setup p 38 for details e Map Event Spot Sets up a selected camera screen as a map event spot screen Refer to Map Event Spot Setup p 39 for details e Draw Motion Block Displays the area where motion is detected with red blocks when a mo
73. ned to the camera screen from the layout screen e E Hotspot Selecting a camera screen in the layout screen and clicking this button sets up the camera screen as a hotspot screen e E Event Spot Selecting a camera screen in the layout screen and clicking the button sets up the camera screen as an event spot screen Map Event Spot Selecting a camera screen in the layout screen and clicking the button sets up the camera screen as a map event spot screen e El Camera Sequence Selecting a camera screen in the layout screen and clicking this button allows you to create a camera sequence and assigns the created camera sequence to the camera screen Clicking the OK button completes registration of the layout Layout Sequence Monitoring You can monitor video from multiple cameras sequentially in more than one predefined layout A layout sequence should be registered on the RAS program for layout sequence monitoring Refer to the following for details about layout sequence registration 40 iRAS Remote Administration System NOTE A layout in this manual refers to a screen organization created by arranging specific cameras in a specific screen format 1 i Select a desired layout sequence from the Layout Sequence nas Remote Administration System admin Live 1 Inside 1 System View Playback About list and drag and drop it on the Live screen Video from cameras added to the layout sequence is displayed in the s
74. nneennenennne 53 7 1 Playing back Recorded Videon 53 Snapshot on Motion EVENt 57 Object Motion Search DI ZOOM CONTO NEE 58 Image te GE 58 7 2 Exporting Recorded Video 58 Exporting as a Self Player Elie i 59 EXporting as a AVI Pl ar crise tice ilaele 61 Chapter 8 Event Handlmg iii 63 Montong VICO lla 64 a a a 65 Chapter 9 System Health Status Monitoring 67 Sale alt MONO assale dla 67 9 2 Status MONO MN sail 68 Chapter 10 kod SC MONA A A AD 69 Chapter 11 Map Editada O 71 AeA ARO OTS TS TING Maio 71 e EE Mapas aa 72 Chapter 12 Controlling With a Network Keyboard nnaannnnnnennnnnnnnnnnnnnnnnnnenenne 75 A A A aa 75 12 2 SOMME CIN salon 76 12 3 ODE UNO see a dear oan 76 MONTO And VIDEO isla 76 Playing Back Recorded Video 77 12 4 Network Keyboard Buttons cccccccocncnncccconcconcncnonccnnononancnnnononancnnnnnnnnncnnnnnnnns 78 Buttons for Operation COMMAMNAS 78 Buttons for RAS System Control 79 TEE 81 OSbD Information seriali 81 Reiler eler lee DEE 81 iRAS Remote Administration System Chapter 1 Introduction This manual describes installation and operation of iRAS Remote Administration System software which is designed to be used with network cameras network video transmitters and digital network video recorders DVRs NVRs IRAS is a software
75. nsitivity Num of diff block Activation Time Sec Find Method Date Time Sensitivity Diff to ref image Activation Time Sec e Find Method Selects a search method Motion Search Searches for images with changes in the Search Zone between two consecutive images for example when there was movement 57 User s Manual Object Search Searches for images with changes which last for the Activation Time in the Search Zone when compared to the reference image for example when an object disappeared e Sensitivity Sets the sensitivity of the change detection The higher the number is the more sensitive It IS e Num of diff block Sets the minimum number of blocks that must be activated to be considered as a change Motion Search only e Diff to ref image Sets the minimum proportion of blocks that must be activated to be considered as a change Object Search only e Activation Time Sets the duration that the change must last to be considered as a change If a change is detected but does not last as long as the Activation Time the change is not considered as a change Zoom Control Clicking the amp Zoom button on the control toolbar allows you to zoom on the current video NOTE PIP is an abbreviation of Picture in Picture and indicates the smaller screen within a screen Dragging the mouse on the camera screen moves the zoomed in area e Slide Bar Adjusts the enlargement ratio You
76. onnected System Boot Up DI System Alive System Restart EI System Shut Down 5 Recorder Bad Disk S M A R T e Disk Bad E Disk Full m Disk Almost Full P Disk Config Change E Disk Temperature Panic Recording On Off E Fan Error On Off Emergency Event If a notify function that notifies an event when the event occurs is enabled for each event in a registered device the device considers an event as an emergency event when the event is detected The RAS system is notified emergency events from the device in the following cases e The device is set to notify this RAS system of emergency events However it is possible that emergency events do not occur if the device is connected for monitoring on the Live tab of the iRAS system depending on the specifications and version of the device e The device is not set to notify this RAS system of emergency events and the device is connected for monitoring on the Live tab of the RAS system e The device is not set to notify this RAS system of emergency events and the Device Real Time Monitoring option is enabled for the device in the iRAS system IRAS Setup gt Device gt device menu Edit Device gt Information tab Refer to 5 1 Device Managing Devices Editing Device Information Information p 20 for details about enabling the Device Real Time Monitoring option For this function to work a callback port should be set up correctly Refer to 5 9 Instant Event p 32 for details abou
77. oring is supported in the Health panel If the Health tab is not on the tab panel go to the System menu click New Tab and Health System View Playback Remove Export Ctrl E Print Ctrl P Playback About Health iRAS Setup ogin D Total Problem Unreachable Heal Logout Lock Ctri Alt L Exit Playback About Health Total Problem e Unreachable Healthy 4 0 0 4 Healthy lt no name gt 10 0 1 0 1 Not Use Not Use Healthy lt no name gt 10 0 1 0 0 1 16 Not Use Healthy lt no name gt 10 0 INTil 1 Not Use e Summary List Displays the health monitoring status of devices for all device groups in summary Total Displays the number of devices in all device groups Problem Displays the number of devices where a problem is detected Unreachable Displays the number of devices that are not connected Healthy Displays the number of devices where no problem is detected Detailed List Displays the status of each device in detail Status Displays the status Healthy No Problem detected Problem Video loss event is detected alarm in device error or recording error Unreachable The device is not connected Problem Displays details regarding the problem Group Displays the list of device groups that the device is registered on Site Displays the device name Version Displays the system version information Cameras Displays the status of cameras that ar
78. ot Object Detection Live Popup Event Spot Video Loss Live Popup Video Blind Live Popup Event Spot Not Use Use Not Use Use Not Use Not Use Use e Click Sets the Instant Viewer window to be displayed when clicking the input output device icon on the map When clicking an alarm in icon clicking activates or deactivates alarm out e Motion Detection Object Detection Video Loss Video Blind Alarm In etc Enables or disables event actions to be taken when each event is detected The event actions will be disabled regardless of the settings below if you disabled the event actions of the input output devices during the map monitoring Disabling event actions Place the mouse cursor over the input output device on the map Click the right mouse button Select Ignore Event Action Live Popup Pops up video from a camera associated camera if the device is not a camera Event Spot Displays video from a camera associated camera if the device 1s not a camera on the event spot screen Event Sound Sounds by playing back a selected audio file wav iRAS Remote Administration System Chapter 12 Controlling With a Network Keyboard You can control the iRAS program by using the network keyboard art 40706 NOTE This function is supported only for this specific model of a network keyboard 12 1 Registerino 1 Register the network keyboard on the iRAS program Go to the System menu Se
79. ou can control the direction of the PTZ camera by clicking the arrow buttons on the direction control panel or by clicking and dragging the mouse on the camera screen e 3 Zoom In Out Zooms the camera lens in or out e Focus Far Near Focuses on near or far objects e Y Iris Open Close Opens or closes the iris of the camera lens e El E Set View Preset See PTZ Preset Control p 48 for an explanation of this function Auto Focus Automatically adjusts focus when the image is out of focus after the image is zoomed in or out only works for some models of Network Camera connections 47 User s Manual Advanced Menu Displays the Advanced Menu window and allows you to use more features that the PTZ camera supports Refer to the PTZ camera manufacturer s manual for details about additional features e Close Exits the PTZ mode and returns to the control toolbar PTZ Pr ntrol You can save camera directions as a Preset so that you can move the camera directly to a saved direction 1 Move the PTZ camera to the desired position 2 Click the El Set Preset button on the PTZ control toolbar and the Set Preset en DI Title window appears Enter a name for the Preset and click the OK button The current position is saved as the Preset name OK Cancel 3 Click the 4 View Preset button on the PTZ control toolbar and the View EZ Preset window appears Select the desired Preset and the PT
80. red layout from the Layout list and drag and drop nas Remote Administration System admin Live 1 Inside 1 it on the Live screen Video from cameras added to the Layout cine al ini i is displayed in the predefined screen format on the screen Site Registering Layouts 1 Go to the System menu and click RAS Setup and select the Device menu 2 Click Layout in the Site panel and then the zk button at the bottom of the Site List panel on the right The Add Layout window appears 39 User s Manual e Name Enter the layout name e Site Displays a list of registered devices cameras or camera sequences You can search for a registered device or camera sequence by entering text beside the H icon Entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found As you enter more text the results narrow e Public Private Displays the layout to all users Public or to a current user only Private The admin user can see all layouts e Owner Displays the user ID of the person who created the layout e Screen Format Select a screen format for the layout to be registered Select a device a camera or camera sequence to assign to the layout in the Site panel and drag and drop it in the desired camera screen of the layout screen Remove Selecting a camera screen in the layout screen and clicking this button deletes the camera assig
81. reen message 29 User s Manual e Position Allows you to change the position of the OSD 2009 06 04 17 53 00 Camera Title Status Icon Date Time Event Alert Motion Block Control Toolbar 5 7 Video Enhancement Video Enhancement GE Original Ratio y a s el TRIVIA Safe Mode y E Deinterlacing Simple Fast Filter Di Anti Aliasing M Important Video Performance Trim The Black noise Edges Wl Disable Transparent Window I Disable Desktop Window Manager DWM Dynamic MultiStream Control screen very Large MN ie Norma EN e H Interactive Bandwidth Control Cancel e Aspect Ratio Select the proper image aspect ratio Original Ratio Fits images within the screen size while maintaining their original ratio Fit to Screen Fits images to the screen size regardless of the aspect ratio Fit to Screen Aspect Ratio Fits images to the screen size keeping the aspect ratio This might cause top and bottom or left and right side of images to be cropped depending on the screen size This aspect ratio is not supported and Original Ratio is applied for camera screens that the following functions are activated Image Zoom Hotspot Event Spot Draw Motion Block Actual Size x1 Displays images in their original size e Color Space Select the color space standard to display video on the screen The color quality or display performance of video might be affected depending on the color space standard select
82. registration at iRAS program Refer to Editing Device Information Remote Desktop p 21 for details about registering the port number and password for the VNC remote connection at iRAS program This function may not be supported depending on the specifications and version of the device e Preview Video Allows you to preview the device s video e Remove Device Deletes the device from the RAS program Editing Device Information Select Edit Device from the device menu 19 User s Manual Information Information Detailed Information H Disable Device WM Device Name Sync Device Real Time Monitoring EN Auto Scan LAN v A 0003220caa 3b local 10 0 17 171 Port Type Port Password No Password e Address Type Select device s address type It allows you to change information for connection to the device e Name Edit the device name You can use the same name for more than one device Le Disable Device The RAS program no longer considers the device registered in the RAS program bel Device Name Sync Automatically applies the name set in the device to the iRAS program kel Device Real Time Monitoring The iRAS program updates the device s event information and device information automatically for all registered devices The connection to a device may not be available depending on the maximum number of simultaneous connections to the device when several RAS systems try to connec
83. rikethrough Not Use Image Position Original Ratio Information Opacity 80 X Coordinate 149 Information Name Align Text Left Y Coordinate 171 Image Width IP Address 4 Information Width 61 Image Height Device Num Name IK 1 Height 25 e Map Attributes Sets the properties of the map Root Map Displays a list of devices registered on the map at the right of the Map panel during the map monitoring supported only for the Map panel e Canvas Sets the properties of the canvas and background image inserted on the canvas Width Height Color Sets the width height and color of the canvas Image Position Sets the position of the background image Information Displays the width and height of the background image e Input Output Device Sets the properties of the input output device icon Name Sets the name of the device icon Icon Ratio Sets the image and ratio of the device icon X Coordinate Y Coordinate Width Height Sets the position and size of the device icon You can also sets the position and size by using the mouse drag and drop on the canvas Associated Camera Associates the device with a camera supported only for an alarm in or audio in device You can monitor video from the associated camera when an event is detected Halo Effect Sets the color of the background of the icon It allows you to more easily find the device icon on the map Information Displays the information about
84. s 10 0 127 121 Device Type E Apply to All Devices OK e Name Address Device Type Displays the name IP address and type of the selected device The name will be updated automatically when the name set in the device is changed if the Device Name Sync option is enabled during the Device setup e ID Password Enter the user ID and password which you set in the device in order to connect to that device remotely e Apply to All Devices Select to apply the same user ID and password to all selected devices if you selected more than one device and the selected devises have the same user ID and password NOTES e If the device is a DVR it might be necessary to enter the DVR port numbers depending on the specifications and version of the DVR e When registering a four channel network video transmitter all four cameras are automatically registered even if some of the four cameras are disabled 4 Click Device Group in the Site panel and then the F button at the bottom of the Site panel The Add Device Group window appears ene _rrrrrrrrrrt AT i Device Group n Select Devices Below Selected Device List Name a Name SB Info De Y 1 Cancel User s Manual e Name Enter the device group name e Location Select an upper group to which the device group will belong e Select Devices Below Selected Device List Check the box beside cameras in the left panel and the selected cameras are added to the right p
85. s devices in a LAN environment not supported for DVRs IP Address Allows you to enter the IP address of a device You can search more than one device at a time by entering a range of IP addresses It is recommended that the device not be networked via DHCP Dynamic Host Configuration Protocol If the device is networked via DHCP connection to the device may not be made properly depending on changes in the external network environment DVRNS Allows you to enter the device name registered on a DVRNS server if the device uses the DVR Name Service DVRNS function Ensure the DVRNS server information on which the device is registered is correct System menu RAS Setup gt Network DVRNS option If the DVRNS server information is not correct the device will not be found Domain Name Allows you to enter the device s domain name registered on a DNS server if the device uses the Domain Name Service Device Information File Allows you to import an xml file which has device connection information and lists the devices Ask your dealer or distributor for details about the xml file Select the devices to register by checking the box beside each device name in the list Selecting the Select All box selects all devices in the list 3 Click the Add Devices button at the bottom iRAS Remote Administration System Device Scan sis ___ 7 EN Auto Scan LAN Start Scan e Address e Description Name Addres
86. st shows recent events within the tnin the selected time range Column MA Event Time Callback Port 8000 10000 Live Text In Time Range en wi Minutes Event Sound DI Object Detection A Event Spot Event monitoring dwell 2 pae Sec Minimum monitoring dwell 3 e ei e Time Range Set up the length of time for an event notification to be displayed in the Instant Event List after notification of the event detection If the event list has 100 or fewer items the event list will remain on the Instant Event List even if the length of time has expired e Column Select the information to be displayed in Instant Event List e Callback Port Set up the port number to receive a callback message from the device The port number you enter should match the port number set on the device for remote callback e Live Text In Time Range Set up the length of time for a text in data to be displayed when a text in event occurs You can check the text in data in the text in viewer window within the time range since the text in event occurred Refer to 6 3 Controlling Cameras Text In Viewer p 49 for details about the text in viewer window e Event Sound Set up to sound by playing back an audio file when an event is notified in the Instant Event list Select a desired event and set up an audio file wav by clicking the BJ button Clicking the A button allows you to test the sound by playing back the selected audio file e Event Spot Vi
87. stores the window Only one of each panel type can be maximized e Displaying hiding a site list in the floating panel Clicking the right mouse button in the camera screen of the panel and selecting the Remote Site Panel from the screen menu displays or hides a site list in the floating panel This is supported for not every panel 16 iRAS Remote Administration System Chapter 5 Setup Go to the System menu Select RAS Setup Select Device nas Remote Administration System admin Live 1 IRAS Setup x System View Playback About AD New Ta b Live 1 Device l a Group Address Description Remove User Panic Record Export Ctrl E Pri nt Ctrl P System Screen Format RAS Setup Device Ctrl Shift D Screen Display User Video Enhancement Panic Record Report Login Logout pra System Ctrl Shift S eg Screen Format Map Exit Screen Display Video Enhancement Report Instant Event Network Map Lock Ctrl Alt L Backup Restore The Device menu allows you to register and manage sites a Group Address Description e Ed Multiple Firmware Upgrade Allows you to upgrade software for several devices at the same time Refer to Managing Devices Upgrading Device s Software p 22 for details Multiple Remote Setup Allows you to change settings of several devices at the same time using a setup file Refer to Managing Devices Changing Dev
88. t Print Image Allows you to export or print the images currently displayed on the screen Audio Broadcast Broadcasts audio to all devices in the current Live tab e Panic Recording Performs panic record for all video in the current Live tab Hotspot Setup NOTE The hotspot in the iRAS program is a predefined camera screen in which video from any camera among those currently displayed can be monitored with emphasis The hotspot screen is surrounded by a red outline 1 Select a camera screen to set up as a hotspot screen on the current monitoring screen 2 Click the E Hotspot button on the toolbar at the bottom of the Live panel and the current connection in the selected camera screen is released The hotspot screen is surrounded by a red outline 3 Select any camera on the screen Video from the selected camera is displayed on the hotspot screen and you can control the camera CAM cam N A 4 5 Event Spot Setup NOTE The event spot in the iRAS program is a predefined camera screen in which video from a camera which an event is detected among cameras currently displayed can be monitored with emphasis The event spot screen is surrounded by a blue outline 1 Select a camera screen to set up as an event spot screen on the current monitoring screen 2 Click the El Event Spot button on the toolbar at the bottom of the Live panel and the current connection in the selected camera screen is released
89. t a password when running the iRAS program Password Expiration Setup Set the password expiration period If the password has not been changed during the password expiration period you will be informed of it when you log on e E Mail Enter the email address of the user An email address must include the character to be a valid address e Phone Description Enter the telephone number and description of the user if you want Only numbers and are allowed when entering a telephone number Click the OK button at the bottom 3 Clicking the registered user group or a user in the list and then the LA button at the bottom allows you to edit the information 5 3 Panic Record It allows you to start or stop recording manually while monitoring video NOTE Panic record is available only when video is currently displayed on the Live tab For example if you change the screen format during panic record and monitoring video is hidden on the Live tab panic record will stop for the hidden video Total Space 0H 0 E Elek Recorded Time Overwrite Yes Recorded Clear All Recorded Data Free Space I Use Panic Recording Storage Path Capacity e Total Space Displays the total and remaining capacity of storage allocated for panic record e Recorded Time Displays the record period 26 iRAS Remote Administration System e Overwrite Displays whether overwrite mode is enabled or disabled When overwrit
90. t search and time lapse search Refer to Timetable Event List p 55 for details Search Filter Sets search conditions for event search Refer to the device s user manual for details about the search condition EJ Calendar Searches video for a specific date Selecting a date displays the recorded data for that date in the timetable The dates containing recorded images are enabled in the calendar El Move to Searches video for a specific time Go To Displays a time setup window Entering a specific time moves to the image for that time Move First Moves to the first recorded image in the data displayed in the timetable Move Last Move to the last recorded image in the data displayed in the timetable Additional Menu Displays a menu Data Source Selects the data source to be searched e Search on Local Searches recorded data on primary storage installed in the DVR e Search on Archive Searches archived data on backup storage installed in the DVR e Search on Other Searches recorded or archived data on Storage used for another DVR then installed in the DVR This may not be supported depending on the specifications and version of the DVR Select Segment Allows you to select a video segment when the DVR s time and date have been reset to a time that is earlier than previously recorded video and there is more than one video segment in the same time range due to time overlap supported only for DVRs which provide t
91. t setting up the callback port The Emergency Event panel appears automatically when emergency events are occurred or you can display the Emergency Event panel manually as follows 63 User s Manual Go to the View menu click Emergency Event Panel Or click the w button in the Instant Event List tem admin Live 1 View Playback About Full Screen Alt Enter Full Screen ToolBar Ctrl Alt Enter Ctrl F Ctrl Ctrl Time Screen Format Show Previous Cameras Show Next Cameras Beh gt P gt gt Set Hotspot Set Event Spot Set Map Event Spot E I sequence Emergency Event Panel Ctrl Alt E Remote Site Pane Mx Event Count 120 Last Event 2013 03 05 16 54 31 Inside 1 Auto Popup Device Date Time Site e Event Count Displays the total number of events in the list e Last Event Displays information of the recently occurred event e Auto Popup Pops up the Emergency Event panel automatically when the RAS system is notified of an event e Event Device Site Date Time Displays information of the event Selecting an event from the list and dragging and dropping it on the Live or Play screen displays on the screen live video or event recorded video from the camera where the selected event occurred Monitoring Video Monitoring video from a camera where an event is detected is supported in the Live panel maximum 4 If a Live tab is not on the tab panel go to the System m
92. t to the device simultaneously If this option is disabled the RAS program updates the information only for the devices that are currently being monitored Auto Scan LAN Allows you to enter the device s mDNS number when you edit the device s address IP Address Allows you to enter the device s IP address when you edit the device s address DVRNS If the device uses the DVRNS DVR Name Service function this allows you to enter the device name which is registered on the DVRNS server when you edit the device s address The name should match the one set during the DVRNS setup in the device Domain Name If the device uses the domain name service this allows you to enter the device s domain name registered on a DNS server when you edit the device s address e Address Edit the device s address based on the selected address type above e Port Edit the port numbers The port numbers you enter should match the port numbers set in the device for remote connection Admin remote monitoring Watch recording Record and two way audio communication Audio e ID Password Edit the user ID and password for connection to the device e Connection Test Click the button to test the connection to the device with the information entered above 20 iRAS Remote Administration System Remote Desktop It allows you to register a port number and password information RENSEDE Detailed Information for the V
93. te panel and then the F button at the bottom of the Site List panel on the right The Add Camera Sequence window appears 43 User s Manual Camera e Name Enter the camera sequence name e Public Private Displays the camera sequence to all users Public or to a current user only Private The admin user can see all camera sequences e Owner Displays the user ID of the person who created the camera sequence e Device List Displays a list of registered devices You can search for a registered device by entering text beside the 2 icon Entering text that you want to search for causes the search results to be displayed Search results are displayed immediately as matching text is found As you enter more text the results narrow e Selected Camera Sequence List Displays the list of cameras registered for the camera sequence Duration sec displays the duration for video from each camera to be displayed on the screen Clicking the Apply all button applies the duration setting to all cameras in the list Select a camera from Device List click the E button and the selected camera is added to Selected Camera Sequence List Clicking the OK button completes registration of the camera sequence 6 2 Map Monitorino You can monitor video from cameras event detection and input output device status on a map for devices registered on the iRAS program A map should be registered on the iRAS program for map monitoring Refer to Chapter 11
94. the registered maps You can monitor video from cameras event detection and input output device s status on a map Refer to 6 2 Map Monitoring p 44 for details Managing Devices You can edit or delete the device from a list You can also connect to a device to change its settings or upgrade its software remotely Go to the System menu Select IRAS Setup Select Device Click a device group in the Site panel and then click a device in the Site List panel Clicking the A button at the bottom of the Site List panel or clicking the right mouse button displays the device menu 18 iRAS Remote Administration System a Group Edit Device Remote Setup Device Firmware Upgrade Remote Desktop Preview Video Remove Device OR e Edit Device Allows you to change information for connection to the device Refer to Editing Device Information p 19 for details e Remote Setup Device Allows you to change the device s settings remotely Refer to Changing Device s Setting Remotely p 21 for details e Firmware Upgrade Allows you to upgrade the device s software remotely Refer to Upgrading Device s Software p 22 for details e Remote Desktop Allows you to connect to the device using the VNC Virtual Network Computing function For this feature to work the VNC function must be enabled in the device and a port number and password for the VNC remote connection must be registered during the device
95. timetable will differ depending on the model of the device timetable Current Playback Date Time Indicates the video time for the current playback location on the Recorded Period Displays the date and time period of the recorded data Clicking anywhere in the empty space and dragging it to the left or right moves to the earlier or later date or time Scrolling the mouse wheel while holding the Ctrl key on the keyboard zooms in and out the time section Camera Title Displays the camera title on the device Recorded Data Displays the recorded data by time in one minute or one hour segments depending e Minute Segments Timetable all devices except some DVR models Red vertical line Indicates the current playback location of video on the timetable Clicking the mouse on the desired time displays the first image recorded within the time Yellow separation line Separates segments when time overlap occurs In this case the recorded data in the time range located after the separation line is the latest Clicking the EJ Calendar button in the Play panel allows you to move to a specific segment directly Click the EJ Calendar button Select a date Select a segment The first image recorded within the selected segment is displayed on the screen The color of the bar Indicates different recording modes Blue for Time lapse Purple for Event Yellow for Pre event Red for
96. tion detection event occurs for the selected camera supported only for connection of network video transmitters Aspect Ratio Save Still Image Remove e Aspect Ratio Select the proper image aspect ratio Fit to Screen Displays images by fitting them to the screen size regardless of the aspect ratio Fitto Screen Aspect Ratio Displays images by fitting them to the screen size keeping the aspect ratio This might cause top and bottom or left and right side of images to be cropped depending on the screen size This aspect ratio is not supported and Original Ratio is applied for camera screens that the following functions are activated Image Zoom Hotspot Event Spot Draw Motion Block Original Ratio Displays images by fitting them within the screen size while maintaining their original ratio Half Size x0 5 to Quadruple Size x4 Selecting the desired image size displays images in the selected size Options are enabled if the selected camera screen can display images in that size e Save Still Image Saves the current image on the screen as an image file at its original size e Remove Disconnects the current connection PTZ Control Clicking the amp PTZ Control button on the control toolbar displays the PTZ control toolbar and allows you to control PTZ Depending on the PTZ camera specifications some features may not work e Direction Control Displays or hides the K Direction Control Panel Y
97. tions as the same as clicking the button in the control Image Processing gt toolbar See Control Toolbar p 56 for details acts rn e Image Effect Adjusts the image effect Refer to Image Effect p 58 ino i for details ottieni e Object Motion Search Allows you to search for changes or motion in the recorded images in the device or the iRAS system Refer to Object Motion Search p 57 for details e Image Processing Enhances playback images Refer to Control Toolbar p 56 for details e Aspect Ratio Select the proper image aspect ratio Fit to Screen Displays images by fitting them to the screen size regardless of the aspect ratio Fit to Screen Aspect Ratio Displays images by fitting them to the screen size keeping the aspect ratio This might cause top and bottom or left and right side of images to be cropped depending on the screen size This aspect ratio is not supported and Original Ratio is applied for camera screens that the following function is activated Image Zoom Original Ratio Displays images by fitting them within the screen size while maintaining their original ratio Half Size x0 5 to Quadruple Size x4 Selecting the desired image size displays images in the selected size Options are enabled when the selected camera screen can display images in that size Remove e Save Still Image Saves the current image on the screen as an image file at its original size 56 iRAS Remote A
98. tton displays a tooltip for the button e PTZ Control Allows you to control PTZ for a camera that supports PTZ control Refer to PTZ Control p 47 for details e f9 Color Control Adjusts the brightness contrast saturation and hue of the current video Clicking the G button cancels the adjustment and reloads the original image This change will be applied to both the video of the RAS program and the device e Image Effect Adjusts the image effect Refer to Image Effect p 49 for details e Image Zoom Zooms in on the image Refer to Zoom Control p 48 for details Camera Sequence Starts or stops camera sequence Refer to 6 1 Monitoring Video Camera Sequence Monitoring p 43 for details e 4 8 Listen Talk Receives audio from the device or sends audio to the device e T Text In Viewer Pops up the text in viewer window supported only when a text in event is detected The camera title bar is highlighted in blue when a text in event is detected Refer to Text In Viewer p 49 for details e Panic Recording Starts or stops the panic recording During panic recording the Panic Recording OSD is displayed in the upper right corner of the camera screen NOTE The panic recording is a function that allows you to manually record video which is currently being monitored Liv reen Men The screen menu is displayed when selecting a camera screen and clicking the right mouse button The scree
99. u will need to install the codec manually 62 iRAS Remote Administration System Chapter 8 Event Handling You can monitor live video from a camera where an event is detected or play back event recorded video if video of the selected event has been recorded The iRAS system is notified events from registered devices and displays the events in the Instant Event List in the following cases e The device is connected for monitoring on the Live tab of the RAS system e The Device Real Time Monitoring option is enabled for the device in the RAS system IRAS Setup gt Device gt device menu Edit Device gt Information tab Refer to 5 1 Device Managing Devices Editing Device Information Information p 20 for details about enabling the Device Real Time Monitoring option a cal a cal a cal a cal a cal a cal a cal a cal a Al a cal a cal a cal AR CA You can change the options of the event list display during RAS Setup Instant Event Refer to 5 9 Instant Event p 32 for details The description of event icons which are displayed in the event list is as follows some event icons may not be supported depending on the specifications and version of the device fe Motion Detection Video Blind CA Video Loss Object Detection B Audio Detection Video Analytics Detection Es Trip Zone Tampering ED Text In OZ Alarm In On Off m m Alarm In Bad Good OI External Storage In Out Device Connected Disc
100. ve video from the selected site is displayed on the screen Site Live 1 6 Press the Menu button The live screen menu is displayed 7 Moving to the desired item by using arrow buttons and pressing the enter button PTZ Control H selects the item in the menu or releases the selection If you want to exit Color Control the current item setting press the Menu button and releases the selection Image Zoom Image Processing gt Alarm Out Text In Viewer Listen Talk Audio Broadcast Panic Recording MultiStream Hotspot Event Spot Map Event Spot Draw Motion Block Aspect Ratio Save Still Image Remove 8 Refer to 12 4 Network Keyboard Buttons Buttons for RAS System Control p 79 for the explanations about other functions Playing Back Recorded Video 1 Press the Play tab ID on the network keyboard 1 17 User s Manual 2 Press the button 3 Press the camera screen ID 1 4 Press the PANE button 5 Select a site to connect to from the Site list and then drag HE Playback About and drop it on the Play screen by using the mouse connected to the network keyboard Recorded video from the selected site 1s displayed on the screen 6 Press the Menu button The play screen menu is displayed 7 Moving to the desired item by using arrow buttons and pressing the enter Image Zoom button selects the item in the menu or releases
101. w Tab Live 1 Remove Export Print iRAS Setup Device Ctrl Shift D User Panic Record Logout System Ctrl Shift S Screen Format Screen Display Video Enhancement Report Instant Event Network Map Lock Ctri Alt L Exit Backup Restore General Il Use buffering for live Mega pixel images Live image no frames detect interval INotUse Disconnection Message Setup DVRNS sever Ades EE port RTP Incoming Port Range om See Don t display broken frames H ive M Playback Buffering Frame Count EMS IA Network Keyboard Il Use Network Keyboard Control Port Cancel 12 2 Connectino Network K rd LCD Di a 1 Press the RAS system ID on the network keyboard 2 Press the button The network keyboard connects to the iRAS system When the connection is succeeded a unique ID is displayed on each camera screen and panel tab as follows System Ol ive 1 X Keel 3 Pressing the GHIET and button at the same time releases the connection Monitoring Video E 1 Press the Live tab ID on the network keyboard 76 iRAS Remote Administration System 2 Press the button 3 Press the camera screen ID 1 4 Press the PANE button 5 Select a site to connect to from the Site list and drag and HS drop it on the Live screen by using the mouse connected Ri iii pi to the network keyboard Li

Chapter 3

Contents

Download Pdf Manuals

Related Search

Related Contents