User Manual
Contents
1. the aspect ratios between the Exactly similarly attach the right side velvet frames to framework The elastic joint of left and right horizontal terminal stops are adjusted simply by releasing the control button to match the frames have been designed to be tight After matching the frame ends by hand as instructed in a tip below the aspect ratio of each media parallel positions with each other can be fine tuned by the two Cap Screws m5 x 30 Fig 13a which are pushing the both frame ends upwards Finally attach the lower horizontal frames to their places Still remove the cover sheet from the circular IR window of left bottom frame The screen with the masking system is now ready for the use TIP A tight center joint of horizontal frames can be connected together without difficulty by pulling the both center ends away from framework bars until they match to each other after which they can be released to go back down against the framework Fig 13b Before doing this the both frames must have been attached from center to the framework bars Fig 12b Top view STEP 14 Now power the system up from either left or right side motor control board Fig 8b and Fig 14 By pressing and holding the OPEN button of remote controller drive the masks to full open 2 40 1 position The opto electrical sensors stop the masks automatically after they2. top and bottom Fig 9 Prepare to attach holders are inserted before the screw can be tightened against the holder thread the mask bar to both upper and lower slide In corner the two Cap Screws brackets using Cap Screws m6 x 12 m4 x 35 are used for pushing marked by b in a close up Tighten the four the elastic joint of corner screws securely with L Wrench 4mm seamlessly together Fig 12c Before tightening the frame Now push the yellow switches of two ends in corner are first detector boards which are locating on the adjusted by hand to match bottom left framework bar marked by in each other By using the L Fig 9 to ON position After this the left wrench 3mm tighten the side mask is not reacting to remote screws to an extent that the controller until the velvet frames have velvet joint becomes firmly been installed in STEP 12 and 13 together STEP 10 Connect the loosen wire ends of right bottom framework bar to the receiver board Fig 10 and Fig 9a Make sure the connectors snap securely to each other y aw aum 7 LL LE EE AO OE LE EE A A A A AI EE OT A OT A A CR 8 STEP 11 Redo the STEP 8 and STEP 9 exactly similarly now to the right side of screen Again make sure the yellow switches of two detector boards on the right part of screen becomes to ON position after performing the steps Assembly Instructions Masking System STEP 13 You are done Enjoy your new 2 40 1 setup In the use
3. 5e to an extent which prevents the bar falling from the Wall Socket Finally do the same procedure as mirror image for the bottom horizontal framework bars which are much similar to the upper bars except for the electrical control boards and wiring they include Fig 8 Bottom view STEP 8 Attach the connector ends on left bottom together as shown in Fig 8a Make sure the parts snap securely to each other Now connect the power for the first time to the socket marked by b in Fig 8 There is an extra notch on a framework slot under the aluminum bracket Fig 8c to offer enough space to feed the DC plug into the socket Masking System Assembly Instructions STEP 9 By pressing and holding the CLOSE STEP 12 button of Remote Controller pointing it to Starting from left vertical Velvet Frame attach the frame to the vertical framework bar only from center the receiver board Fig 9a and holder of frame String the Cap Screw m5 x 30 through the hole and using L wrench 4mm tighten the simultaneously pulling the left mask from screw securely against the frame holder exactly as shown in Fig 12a velvet frame is drawn transparent in the velvet bar drive the mask fabric close a close up pictures Similarly only from center attach the upper left horizontal frame to the horizontal until the bar reaches the sliding brackets in framework bar Fig 12b There are three slots in the horizontal framework bar to where the frame
4. Assembly Instructions INSTALLATION INSTRUCTIONS Carefully remove and unwrap all the contents of box Referring to the parts list make sure you have everything needed to proceed with the installation of the masking system If any parts are missing contact Prismasonic immediately Inspect the parts to make sure there are no shipping defects If you notice a problem with the item itself or the screen s mechanical system contact Prismasonic immediately Part List Wooden Assemblies E Framework Bar 6 pcs E Velvet Frames 17 cm 6 pcs Aluminum Brackets Extension Bracket 2 pcs Frame Holder M 78 pcs Wall Plate 7 pcs Wall Plate Side 2 pcs Wall Mount 2 pcs Wall Mount Side 4 pcs Wall Socket 16 mm 4 pcs Wall Socket L 76 mm 4 pcs 116 100 mm 4 pcs 136 131 mm 4 pcs 156 Hardware Cap Screw M4 x 35 8 pcs Cap Screw M5 x 16 8 pcs Cap Screw M5 x 30 10 pcs Cap Screw M6 x 12 8 pcs Cap Screw M6 x 16 4 pcs Cap Screw clear M6 x 20 78 pcs Cap Screw M8 x 16 4 pcs Set Screw M8 x 6 4 pcs Torx Screw black 12 pcs Torx Screw clear 4 pcs Tools amp Misc L wrench 3 mm L wrench 4mm Do not exist if ordered with a screen L wrench 5 mm Do not exist if ordered with a screen Torx Driver Do not exist if ordered with a screen Screw Driver Velvet Stickers 4 pcs Electrical Parts E Power Cord E Power Converter E Remote Controller Upgrade parts For
5. disappear under the main velvet frames After this drive the masks to full close 1 33 1 position where they again automatically stop If the side mask travels from open to close are not quite synchronous to each other their speed can be further adjusted This is done with Screw Driver by opening 5 70 rounds to counter clock wise the trimmer screw of motor control board marked by a in Fig 14 but only at the side which was moving slower The iterative tuning back and forth can be performed to find the perfect synchrony Similarly the calibration can be done to the close to open movement Now however the trimmer screw marked by b in Fig 14 is closed 3 5 rounds to clock wise at the side which was moving faster And again the iterative tuning back and forth can be operated to find the synchrony Masks have been driven to full open 2 40 1 position NOTE The system is good to be powered down while adjusting the trimmer screws with screw driver hihi e wiii Ao zie e uF WH iHiiii ae kd mt s Ma Ss F vii O left side board right side board
6. en of part is pointing STEP 4 C 50 C AT50 first modify your existing screen according to Steps 1 5 of Cinoscreen C 50 C AT50 user manual The new parts which are needed for the modification are included to package Also make sure both two Wall Plates and all four Wall plate S are assembled to the wall screw hole according to Fig 1a of Cinoscreen C 50 C AT50 Da user manual even if the screen frame work 1 a attaches only to upper three plates Now attach the total four Wall Socket Ls to remaining screw holes of every four Wall Plate S Fig 4a and four Wall Sockets to both two Wall Plates Fig 4b Tighten the sockets securely and make sure the heels of sockets come in contact with the plates Next attach the Frame Holder M parts onto new 170 mm wide Velvet Frames By using Cap Screws clear m6 x 20 prepare to attach the new holders to frames exactly as shown in Fig 2 Tighten the screws securely using L wrench 4 mm In the horizontal frames the screw holes of new frame holders are pointing from center to side whilst in the vertical frames only the holder in the middle is pointing from center to side and the two others in side are pointing from side to center Masking System Assembly Instructions STEP 5 Starting from the horizontal Framework Bar at top left first attach the Wall Mount to Extension Bracket by using two Cap Screws m6 x 16 Fig 5a Next using three Torx Screw black connect the Exten
7. older models of Cinoscreen C50 C AT50 Corner Bracket modified 2 pcs Extension Bracket modified 1 pcs Wall Plate 7 pcs Wall Plate Side 2 pcs Wall Mount 7 pcs Wall Mount Side 2 pcs Wall Socket 16 mm 2 pcs Wall Socket L 76 mm 2 pcs 176 100 mm 2 pcs 136 131 mm 2 pcs 156 Cap Screw M6 x 16 4 pcs Set Screw M8 x 6 2 pcs Assembly Instructions Masking System Assembly Instructions STEP 3 STEP 1 First attach the four velvet stickers exactly as presented in Fig 3 All four First unpack the items from shipping tubes and boxes As shown with an arrows in Fig 1 stickers are in line right below the bottom horizontal screen framework bar remove the two delivery bars from each horizontal and vertical Framework Bars which The stickers at corners are also in contact with the side wall plates while the connect the two bars to each other Use L Wrench 3 mm for the screws to release the center ones are separated from the plates with a distance as informed in a bars picture The stickers are for preventing the parasitic reflections of opto electrical transmitters of mask travel detection from wall to system thus making the performance 100 reliable with all wall materials l l e Pie 635mm UE 635 mm 156 526mm Heke 526 mm 136 421mm 116 421mm 116 STEP 2 Direction to where the screw hole If you are upgrading the old version of Cinoscre
8. sion Bracket to the slot of framework bar Fig 5b After this by using Torx screw clear attach Wall Mount Side to the pre assembled corner bracket as shown in Fig 5c Finally string the wall mounts to Wall Sockets of Wall Plates exactly as shown in Fig 5 By using L Wrench 4 mm insert and tighten the Set Screw m6 x 8 in the screw hole at location d to an extent which prevents the bar falling from the socket STEP 7 To finalize the masking framework assembly attach the two vertical framework bar assemblies to the horizontal bars Fig 7 In every four corner use Cap Screw m8 x 16 marked with a in close up and two Cap Screws m5 x 16 marked with b in close up Tighten the screws securely using L Wrench 5 mm and L Wrench 4mm Make sure that after installation the loosen wire ends of both vertical bar assemblies are locating in bottom corners so that they can be further connected to the motor control boards NOTE The pre assembled bars which are assembled in top can be identified not including the electrical control boards on them d a N j ae Do F3 O a ths STEP 6 i ir i f MHH Now attach the top right Framework Bar Fig 6 First string the Wall Mount Side to Wall socket after which it F FN 2 h connect the other end to extension Bracket by three Torx Screws 5 x 35 Tighten the screws securely using Torx Driver Also now screw the Set Screw m6 x 8 to the screw hole at location Fig
Download Pdf Manuals
Related Search