MINICUBE2 Setuo Manual IF
Contents
1. a V850 or 78KO microcontroller Set to M1 when the target device is a 78KOS or 78KOR microcontroller Power select switch Target system _ 2 I MINICUBE2 PEEL cocci TEE orionas TA i m mj Ct ii Connect to host machine using USB cable Mode select switch Power select switch s i M Set to T when the power supply of the target system is used recommended pana gt e i bad Set to 3 when 3 V is supplied to the target system current rating 100 mA MINICUBE2 USB cable Hostimachina Set to 5 when 5 V is supplied to the target system current rating 100 mA Note 1 A 20 MHz clock is mounted on the 78KO OCD board at ship ment To change the setting refer to the user s manual Note 2 A 10 pin target cable can also be used to perform on chip de bugging for a 78KO microcontroller lt 2 gt Connection Do not turn on power to the target system before connection Connect hardware in the order shown below Connect the 78KO OCD board tet enclosed by a dashed line to MINICUBE2 in advance when performing on chip debugging for a 78KO microcontroller not necessary when performing flash programming After connection the mode LED lt 3 gt Power application to target system Turn power on to the target system On chip debugging gt Securing the user resources and setting the security ID Before on chip debugging is performed with MINICUBE2 the user resources such as memory spaces must be se2. DS see figure right hand MINICUBE2 software page http www necel com micro ods eng tool MINICUBE2_Software list html If the firmware version is not the latest refer to the MINICUBE2 diagnos tic tool user s manual and update the firmware After self testing and firmware version checking are completed discon nect MINICUBE2 and the host machine once Setting and Connecting Hardware Perform settings on MINICUBE2 and then connect MINICUBE2 to the target system The following description assumes that the target system circuits have already been connected For information on target system circuit design refer to the MINICUBE2 user s manual RE MINICUBE2 Diagnostic Tool SELF TEST FAW MINIGUBE2 Information MINICUBE2 41004 FAW v1 00 Firmware version lt 1 gt MINICUBE2 utilities startup Connect MINICUBE2 which is in the state just after purchase to the host machine as shown in the right hand figure and then start the MINI CUBE2 diagnostic tool from the Start menu OK i l bos PTET TTT tees PTTL TTL EEE START MINICUBE2 st USB cable Host machine see figure right hand is lit For the meaning of the mode LED light refer to the MINICUBE2 user s manual lt Mode LED J anua p lt 1 gt Switch setting Set the switches on the MINICUBE2 main unit see following figure as follows g N Mode select switch ma gt Set to M2 when the target device is Pennan S 16 pin target cableNote 2
3. For information on the circuit connection refer to the MINICUBE2 user s manual lt 3 gt Software provided by NEC Electronics partners When using software provided by an NEC Electronics partner refer to the documents prepared by the company lt 4 gt Optional products A target board for a trial use is available for MINICUBE2 used with one of the following devices A connector for MINICUBE2 is mounted on this board so you can start checking of the device operation soon after opening the package lt 2 gt Troubleshooting If there seems to be any problem with the MINICUBE2 operation use the following check tools to discover the problem MINICUBE2 utilities MINICUBE2 diagnostic tool OCD checker tool for checking target system commu nication If the above tools cannot resolve the problem see the FAQ on the website or access the following URL for con sulting gt lt V850 microcontrollers 78K microcontrollers http www necel com en contact contact_e html V8S0ES KG2 78KO LG2 V850ES HG2 78K0 KF2 V850ES JG2 78KOS KB1 V850ES IE2 78KOR KG3 More devices will be supported in the future For order ing information and other optional products refer to MINICUBE2 information site 1 Preface lt 2 gt For where to inquire access the following NEC Electronics website http www necel com en contact contact_e html
4. INICUBE2 to the host machine until in stallation of software is completed lt 1 gt Debugger A debugger is required to perform on chip debugging Download integrated debugger IDxxQB which is supported by the tar get device from ODS Example Debugger for V850 microcontrollers ID850QB Debugger for 78KO microcontrollers ID78KO QB Run the executable file downloaded The installation wizard starts Fig ure 1 so install the debugger USB driver and MINICUBE2 utilities following the directions on the screen Figure 1 Install Wizard 500 50 Integrated Debugger 3 20 1085008 3 20 Documents M v850 IECUBE USB Driver V1 10 64KB M V850 MINICUBE USB Driver V1 10 64KB MINICUBE2 USB Driver 1 10 64KB MINICUBE Utilities 1 00 320KB MINICUBE Utilities 1 00 Documents 640KB lt ID850QB V850 Integrated Debugger V3 20 gt bugger provides user with variable Hodis in order t Available Space 9 573 104KB lt 2 gt Device file A device file is required to perform on chip debugging Download the device file corresponding to the target device from ODS and decompress the file Start Device File Installer Figure 2 from the Start menu and click the Install button Specify the folder where the decompressed files are stored specify NECSETUP INI _csetup INI in English version OS and then continue the subsequent procedures Document No U17966EJ4VOIFOO 4th edition Date Published November 2007 N P
5. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http Awww renesas com Send any inquiries to http www renesas com inquiry CENESAS 8 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is gr
6. anted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document b
7. ce equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions unde
8. cured The security ID must be set in order to prevent the program from being read by an unauthorized person For details on these settings refer to the MINI CUBE2 user s manual If the flash memory of the target device has already been erased OxFF is written to the entire flash memory space the debugger starts without problem This enables checking of the target system circuit design Devices whose flash memory has been erased have the security ID OxFFFFFFFFFFFFFFFFFFFF 10 bytes The setting of security ID is unnecessary in 78KOS Flash programming Debugger startup Start the debugger from the Start menu For the operation after startup refer to user s manual of the debugger QB Programmer startup Start the QB Programmer from the Start menu For the operation after startup refer to user s manual of the QB Programmer The information in this document is current as of November 2007 The information is subject to change without notice For actual design in re fer to the latest publications of NEC Electronics data sheets or data books etc for the most up to date specifications of NEC Electronics products Not all products and or types are available in every country Please check with an NEC Electronics sales representative for availability and additional information No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics NEC Elec tro
9. gt lt 4 gt Parameter file A parameter file is required to perform flash programming Download the parameter file corresponding to the target device from ODS and decompress the file A prm file is decompressed in a folder Copy the decompressed parameter file to arbitrary folder Specify the copied parameter file when specifying a parameter file at the QB Programmer device setup procedure lt 5 gt USB driver recognition After installation of software is completed connect MINICUBE2 to the host machine The USB driver is then recognized With Windows XP the Found New Hardware wizard starts Select Install the software automatically Recommended and then proceed to the subsequent procedures NEC Electronics Corporation 2006 Self testing of MINICUBE2 and checking firmware Check if MINICUBE2 has an initial failure and the firmware is the latest If the firmware version is not the latest debugging of the target micro controller or flash programming may not be possible lt 2 gt Execution of self testing and checking of firmware version Click the Start button on the initial screen of the MINICUBE2 diagnostic tool Self testing then starts If MINICUBE2 TEST OK is displayed your MINICUBE2 is normal If not consult an NEC Electronics sales representative or distributor The firmware version is the latest if the displayed version matches the one shown under MINICUBE2 firmware posted on O
10. nics assumes no responsibility for any errors that may appear in this document NEC Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products No license express implied or otherwise is granted under any patents copyrights or other in tellectual property rights of NEC Electronics or others Descriptions of circuits software and other related information in this document are provided for illustrative purposes in semiconductor product Operation and application examples The incorporation of these circuits software and information in the design of a customer s equipment shall be done under the full responsibility of the customer NEC Electronics as sumes no responsibility for any losses incurred by customers or third par ties arising from the use of these circuits software and information Note 1 NEC Electronics as used in this statement means NEC Electronics Corporation and also includes its majority owned subsidiaries 2 NEC Electronics products means any product developed or manufac tured by or for NEC Electronics as defined above Information lt 1 gt Notes on target system circuit design A circuit dedicated to communication between MINI CUBE2 and the target device must be designed on the target system
11. r certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Elec
12. rinted in Japan Documents related to MINICUBE2 hardware are available at the above website The MINICUBE2 user s manual that appears in this leaflet is also available on this website lt 3 gt MINICUBE2 software NEC Electronics software for MINICUBE2 is available on the following website hereinafter referred to as ODS http www necel com micro ods eng Use of the latest version of software is recommended If you wish to receive an upgrade notification concerning the following software complete the registration for the upgrade notification service found on the ODS home page Debugger Device file Parameter file When using software provided by an NEC Electronics partner refer to the documents prepared by the partner company Figure 2 Device File Installer Device Name _ uPD 70F3259Y PD703107 u uPD70F3116 uPD70NB85E 4 uPD703102 J EC ELECTR uPD703002 E PROGRAM FILES NEC ELECTR uPD OF3318Y E PROGRAM FILES NEG ELECTR uPD NFA2AT F PROGRAM FIIFS NFG FIFOTR lt 3 gt Programming GUI QB Programmer The QB Programmer is required to perform flash programming Download the QB Programmer from ODS Run the executable file downloaded The installation wizard starts so install the QB Programmer USB driver and MINICUBE2 utilities fol lowing the directions on the screen It is not necessary to select com ponents that have already been installed in step lt 1
13. tronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics oa MINICUBE cZ On Chip Debug Emulator with Programming Function Preface Thank you for purchasing MINICUBE2 MINICUBE2 is an on chip debug emulator that can be used for flash memory programming as well as on chip debugging of NEC Electronics on chip flash memory microcontrollers Please entirely read this document first you will obtain an overview of information on preparation for using MINICUBE2 startup support and so on lt 1 gt Checking the package contents Check the package contents in accordance with the packing list sup plied with MINICUBE2 If there are any missing or damaged items consult an NEC Electronics sales representative or distributor lt 2 gt MINICUBE2 product information and documents For information on MINICUBE2 access the following NEC Electronics website hereinafter referred to as MINICUBE2 information site http www necel com micro english product sc allflash minicube2 html Software installation MINICUBE2 software must be installed before using MINICUBE2 The following explains how to install NEC Electronics software Caution Do not connect M
14. ut Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers offi
Download Pdf Manuals
Related Search