Product Manual
Contents
1. Wall Mounting Optional Refer to the instructions that come with the base mounting kit To convert your LCD display from a desk mounted to a wall mounted display do the following 1 Verify that the Power button is turned Off then disconnect the power cord 2 Lay the LCD display face down on a towel or blanket 3 Remove the Plastic Covers from the back of the LCD display 4 Remove the four screws attaching the base Screw dimension M4 x 10mm 5 Remove the Rubber Plugs from inside the four VESA screw holes 6 Attach the mounting bracket from the VESA compatible wall mounting kit 100 mm x 100 mm distance 7 Attach the LCD display to the wall following the instructions in the wall mounting kit NOTE For use only with UL Listed Wall Mount Bracket with minimum weight load 12kg 21 Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar To assure you receive all the benefits of your Planar product and services register your Planar product today Visit our website to register your product at http www planar com support product_registration html Cables Replacement Lamps Accessories To find cables replacement lamps and accessories for your Planar projector LCD monitor touch screen or other Planar products visit our online store at www PlanarOnline com or find other stores who carry Planar products at http www planar com howtobuy Technical Supp2. DVI Dot Clock Max Resolution 1920X1080 60Hz een renege Few OFF Mode Analog 0 7Vp p Standard 750 Positive Digital DVI Digital Visual Interface Standard Rev 1 0 compliance Digital HDMI 1 3 PowerSource 100 240VAC50 60Fz Environmental Operating Temp 5 to 40 C Considerations Storage Temp 20 to 60 C Operating Humidity 15 to 90 560 88W X413 41 H X249 69 D Input Video Signal 17 FACTORY PRESET TIMING TABLE HORIZONTAL VERTICAL VGA TA XER 18 CONNECTOR PIN ASSIGNMENT 24 Pin Color Display Signal Cable PIN NO DESCRIPTION PIN NO DESCRIPTION TMDS Data 2 TMDS Data 3 TMDS Data 2 TMDS Data 2 4 Shield Ground for 5V a TI a I PN a L 74 4 TMDSDatad 16 Hot Plug Detect 5 TMDSData4 17 TMDS Data 0 6 DDC Clock 18 TMDS Data 0 b 28 3 O 20 ae PANA NE il es ee Paes i TMDS Data 0 5 DDC Data Shield TMDS Data 5 TMDS Data 1 TMDS Data 5 TMDS Data 1 TMDS Clock Shield TMDS Data 1 3 12 TMDS Data 3 24 TMDS Clock 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 9 7 10 11 12 19 19 Pin Color Display Signal Cable DESCRIPTION DESCRIPTION 1 TMDS Data 2 7 11 ITMDS Clock Shield 2 JIIMDS Data 2 12 TMDS Data 1 15 Shield DDC SCL DDC CEC Ground TMDS Data y aa Power max Shield 50mA Hot Plug Detect TMDS Clock S 6 Le 20
3. support FAQ 15 16 Error message amp possible solution 17 Appendix cara inne enema a 17 Specifications 17 Factory preset timing table 18 Connector pin assignment 19 20 Wall mounting optional 21 Product registration and technical support 22 For YOUR SAFETY Before operating the monitor please read this manual thoroughly This manual should be retained for future reference FCC Class B Radio Frequency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user
4. Image T VGA input noise Setup ony H Position Adjust the horizontal position of the picture VGA input only V Postion Adjust the vertical position of the picture VGA input only 10 Main Main Menu a Menu Description Item Icon Normal Color Temperature RGB value is nonadjustable ae Warm sisal Aran RGB value is nonadjustable fii Cool Color Temparaiung RGB value is nonadjustable RGB Color Te t sRGB 5 o 4 ampan ure RGB value is nonadjustable Color FA Temp Adjust R G B Y C M levels as desired User R Adjust Red Gain User G Adjust Green Gain User B Adjust Blue Gain User Y Adjust Red Green Yellow Gain User User C Adjust Green Green Cyan Gain User M Adjust Red Blue Magenta Gain Note When Color Temp is set to User Color Temp DCR Color Boost Picture Boost can be ad justed When Color Temp is set to Normal Color Temp DCR Color Boost Picture Boost are reset to factory presets Demonstrates Color Boost Enhancement in half of screen In this mode when Nature Skin Green Field sky Blue or Auto Detect are activated the enhanced boost will appear on the left side of the screen 11 Main Main Menu os Menu Description Item Icon Frame Size When Bright Adjust the size of the Frame Frame is on Brightness When Bright Brightness Adjustment for Enhance Area Frame is on Contrast When Bright Contrast Adjustment for Enhance Area P
5. PLANAR PX2411MW LCD Monitor USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders TABLE OF CONTENTS FOr your safety annn 1 Saret precautions Tak 2 Special notes on Icd monitors 7777777777777777 3 Before you operate the monitor 3 Features Se aa 3 Packing list 3 Installation instructions 4 Controls and connectors 5 Adjusting the viewing angle 6 OPEFAEIN GANSU UCTIONS sexta seme ese a aaa aaa aana 7 General instructions 7 How to adjust a setting 9 Adjusting the picture 10 13 Plug and play 14 Technical
6. ay remain after switching the image when the same image is displayed for hours In this case the screen is recovered slowly by changing the image or turning off the Power Switch for hours When the screen becomes black or flashing or cannot illuminate any more contact your dealer or service center to replace parts Don t repair the screen by yourself BEFORE YOU OPERATE THE MONITOR FEATURES 23 6 60 cm Wide ScreenTFT Color LCD Monitor Crisp Clear Display for Windows Recommened Resolutions 1920 1080 60Hz Ergonomic Design Space Saving Compact Case Design PACKAGE LIST The product package should include the following items Oi ee IE Na LCD Monitor Stand User s Guide Power Cable VGA Cable DVI Cable Audio Cable INSTALLATION INSTRUCTIONS STAND 1 Puta piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down 2 Install the Stand Base to the Monitor 3 Fix the Monitor with the Stand by the screw 2 firmly and the knob of the scew push down The knob of the screw push down 4 MAR 4 Screws for Stand Base fixinq Stand Base lt Remove gt 1 Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down 2 Pull up the knob of the scews and remove the screws and the Stand Base lt Stopper pin gt Please stand the monitor and t
7. emperature When the brightness of the screen lowers after being used for a certain period and the function of the display is affected send it to our authorized service center for repair Horizontal or vertical disturbances Use win 95 98 2000 ME XP shut down theca cap mode Adjust CLOCK and FOCUS or perform hot key AUTO key No Plug amp Play Picture is fuzzy The power LED is ON orange but there s no video or no picture Poor brightness or contrast 15 TECHNICAL SUPPORT FAQ cont CLOCK pixel frequency controls the number of pixels scanned by one horizontal sweep If the frequency is not correct the screen shows vertical stripes and the picture has not correct width FOCUS adjusts the phase of the pixel clock signal With a wrong phase adjustment the picture has horizontal disturbances in light picture For FOCUS and CLOCK adjustment use dot pattern or win 95 98 2000 ME XP shut down mode pattern ERROR MESSAGE amp POSSIBLE SOLUTION CABLE NOT CONNECTED 1 Check that the signal cable is properly connected if the connector is loose tighten the connector s screws 2 Check the signal cable s connection pins for damage INPUT NOT SUPPORT Your computer has been set to unsuitable display mode set the computer to display mode given in the following table 16 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel 60cm 23 6 Pixel pitch 0 2715 H x 0 2715 V
8. he monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions e Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided e The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug e Unplug the unit during a lightening storm or when it will not be used for long period of time This will protect the monitor from damage due to power surges e Do not overload power strips and extension cords Overloading can result in fire or electric shock e Never push any object into the slot on the monitor cabinet It could shor
9. hen remove the stopper pin on the back of the stand slowly while Pushing top face of the stand before you install the monitor Careful attention is required as the monitor is sorung loaded and may expand quickly when removing it Stopper pin POWER CORD Power Source 1 Make sure that the power cord is the correct type required in your area 2 This LCD monitor has an External universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required 3 Connect the AC power cord into your LCD monitor s power input socket The AC power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your LCD monitor CONTROLS AND CONNECTORS SIGNAL CABLE Connecting the Signal Cable Plug one end of the signal cable to the LCD monitor and the other end to a computer or a video source Caution If the AC outlet is not grounded with three holes install the proper grounding adapter not supplied Figure 2 Connecting Cables Power Cable HDMI Cable DVI Cable D SUB Cable Audio cable ADJUSTING THE VIEWING ANGLE e For optimal viewing it is recommended to look at the full face of the monitor then adjust the monitor s angle to your own preference e Hold the stand so you do not topple the monitor when you change the monitors angle e Youare able to adjust the monitor s angle from 5
10. icture Frame is on Asat Hue When Bright Frame Hue Adjustment for Enhance Area is on Saturation When Bright Saturation Adjustment for Enhance Area Frame is on Position Adjust the horizontal position of the Frame When Bright ia si on Adjust the vertical position of the Frame Enhance Area function Bright Frame Note Bright Frame and Frame size settings are not stored Adjust the OSD timeout Set OSD display language English is default setting UH Position Adjust the horizontal position of the OSD Adjust the vertical position of the OSD OSD Setup OSD 12 Main Main Menu ict Menu Description Item Icon Input Select Select input source VGA DVI or HDMI Auto Adjust Auto Adjust the H V Position Focus and Clock of picture VGA Input Only Turns on or off the two way communication between the graphics card and the monitor DDC CI With DDC CI turned on some monitor setting Extra re can be adjusted through the graphics card a using a computer Reset Reset OSD settings Information Show the resolution H V Frequency and input port of current input signal 13 PLUG AND PLAY Plug amp Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The DDC2B is a bidirectiona
11. id into monitor which will result in the damage of component 8 HOW TO ADJUST A SETTING Sa Press the MENU button to activate the OSD window Press or to navigate through the functions Once the desired function is highlighted press the MENU button to activate it If the function selected has a sub menu press or again to navigate through the sub menu functions Once the desired function is highlighted press MENU button to activate it Press or to change the settings of the selected function To exit and save select the exit function If you want to adjust any other function repeat steps 2 3 Luminance it E lt gt Gamma lt j gt lt YN gt Figure5 The OSD Message ADJUSTING THE PICTURE Main Menu van ae Menu Description Item background Choose one of the following ECO mode settings Standard Brightness 90 Contrast 50 adjustable aik Text Brightness 20 Contrast 80 nonadjustable Luminance MTN Intemet Brightness 40 Contrast 80 nonadjustable Game Brightness 60 Contrast 80 nonadjustable Sports Brightness 100 Contrast 80 nonadjustable Movie Brightness 80 Contrast 80 nonadjustable Gamma Adjustment Enhances Contrast Ratio Note When this function is turned On you cannot adjust the current settings for Contrast Brightness ECO mode or Gamma Adjust picture Clock to reduce Vertical Line VGA input noise only Focus Adjust Picture Phase to reduce Horizontal Line
12. is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only PRECAUTIONS e Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement e Donot place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount t
13. l data channel based on the FC protocol The host can request EDID information over the DDC2B channel THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green monitor standards as set by the Video Electronics Standards Association VESA and The Swedish Confederation Employees NUTEK This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wallet plug with NEMA 5 15 style and is UL listed and CSA labeled The voltage rating for the power cord shall be 125 volts AC Supplied with units intended for connection to power outlet of personal computer Please use a cord set consisting of a minimum No 18 AWG type SJT or SVT three conductors flexible cord One end terminates with a grounding type a
14. ort Visit Planar at http www planar com support for product registration operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online troubleshooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANARI 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply 22 Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2009 Planar Systems Inc Planar is aregistered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice Q41G240193511A
15. t circuit parts causing a fire or electric shock Never spill liquids on the monitor e Do not attempt to service the monitor by yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel e To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 5A e The wall socket shall be installed near the equipment and shall be easily accessible Important Recycle Instruction Lamp s inside this product contain mercury and must be recycled or disposed of according to local state or federal laws For more information contact the electronic industries alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem NOTES Due to the nature of the fluorescent light the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears You may find slightly uneven brightness on the screen depending on the desktop pattern you use The LCD screen has effective pixels of 99 99 or more It may include blemishes of 0 01 or less such as a missing pixel or a pixel lit all of the time Due to the nature of the LCD screen an afterimage of the previous screen m
16. to21 Figure 3 NOTES e Do not touch the LCD screen when you change the angle It may cause damage or break the LCD screen e Careful attention is required not to catch your fingers or hands when you change the angle OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitoron or off The other control buttons are located at front panel of the monitor See Figure 4 By changing these settings the picture can be adjusted to your personal preferences e The power cord should be connected e Connect the video cable from the monitor to the video card e Press the power button to turn on the monitor position The power indicator will light up T t E e e y f Figure4 External Control Button button Menu Enter 6 Powerbutton FRONT PANEL CONTROL e Power Button Press this button to switch ON OFF monitors power Power Indicator Blue Power On mode Orange Off mode MENU ENTER Activates OSD menu or function adjust confirm ECO Activates the ECO control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated Volume Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated Source Auto Adjust Exit When the OSD is OFF pressing Auto Source button will toggle bet
17. ttachment plug rated 10A 250V CEE 22 male configuration The other end terminates with a molded on type connector body rated 10A 250V having standard CEE 22 female configuration Please note that power supply cord needs to use VDE 0602 0625 0821 approval power cord in European counties 14 TECHNICAL SUPPORT FAO Problem amp Question amp Problem amp Question PossibleSolution Solution Check L a E the Power Switch is in the ON Power LED is not on position Power Cord should be connected Check if the PC system is Plug amp Play compatible Check if the Video Card is Plug amp Play compatible Check if the D 15 plug pin of Video Cable is bent Adjust the Contrast and Brightness Controls pattern is present in the picture electrical interference Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitors video cable is properly connected to the computer Inspect monitor s video cable and make sure none of the pins are bent Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key Missing one of the primary colors make sure that none of the pins are bent Adjust pixel frequency CLOCK and FOCUS sized properly or press hot key AUTO Adjust RGB color or select color white does not look white t
18. ween sources Press continuously to select the input source indicated in the message bar Press Menu Enter button to change to the selected source Auto configure hot key VGA input only When the OSD is OFF press and hold down the button for 2 seconds to auto configure When OSD menu is ON this button will act as a Exit Key Exit OSD menu OSD Lock Function To lock the OSD press and hold the MENU button while the monitor is off and then press power button to turn the monitor on To un lock the OSD press and hold the MENU button while the monitor is off and then press power button to turn the monitor on NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor For maximum protection repackage your monitor as it was originally packed at the factory To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it Do not scratch the screen with hard things it may cause permanent damage Don t leak liqu
Download Pdf Manuals
Related Search