029ManualCmB&N UK.FH9
Contents
1. 500 1 335mm x 335 mm LONG 625 WIDE 395 HIGH 170 LONG 680 WIDE 460 HIGH 240 8 2Kg 12 3 Kg OPTIONAL ACCESSORIES oo max 217 min 170 Frame Kit Four aluminium sections squares Screws etc to build a frame that replace the technical ceiling outlines Armstrong or similar and gives a professional ending and support in plaster ceilngs wood ceilings etc With a professional ending as support on your Cinema Mirror installations 505x595 mm 645x645 mm Inside Dimensions Outside Dimensions2. INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION Enema mirror 1 CONSIDERATIONS a figure 1 Cinema Mirror is an active optic set to be installed in false ceilings hiding the projection equipment and that through a pulsation it opens a floodgate of ew 335x335 mm allowing the projection of the image thanks to its two mirrors without causing the trapeze effect on the image For that Cinema Mirror and the k screen must be in the same plane or with a difference from 0 to 12 cm Fig 1 Some manufacturers of Data Video projectors include electronics for a trapeze correction higher than 272 which allows usto increase the level difference between the Cinema Mirror and the screen Always be sure to perpendicularly set the projected light with the projection screen j any difference may negatively affect the d projector s focal 20 cm image Fig 2 The optic mirrors of this equipment are protected by a plastic film to avoid accidents Remove this film when it is indicated by this manual Do not do so beforehand INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION BEFORE USING FOR THE FIRST TIME Before proceeding to the installation and manipulation read carefully this manual and
3. make any effort to stop or help the active mirror gate in its path the mechanics of the motor can be seriously damaged and the warranty of the product willbe lost If you observe any defect this may be due to the handling or lack of care during transport of Cinema Mirror Contact your distributor s technical service Activate the button for opening or closing not included on the Cinema Mirror The motor of the active mirror will be put into operation Remove the film that protects the optic mirrors during transport and pre installation Switch on the projector and wait a few minutes so that the projector reaches its maximum brightness The light or image thrown by the projector through the active mirror determines the place where the projection screen should be installed Remember that you can work on the projector zoom to fix the screen width Install the projection screen guided by the light spectrum thrown by the projector If you use a screen with black side margins theimagewill be better profiled as television sets do in their cathode ray tubes INSERT A VIDEO OR PC SIGNALIN THE INSTALLED PROJECTOR The control lever of red color regulates the position and opening of the active mirror Fig 3 detail 2 and consequently the projection height on the screen Place the control lever on the upper part Activate the motor with the installed push button Observe the image that is projected on the screen T
4. of 10 Metric mm If the equipment is adjustable mobile above the audience or excessive in weight for safety reasons it should be secured with a chain 4 mm link thickness or cable of 6 mm diameter steel from the equipmentto the building structure be it the ceiling floor or walls that support at least 10 times the weight of the equipment The equipment operation is for interior use in aventilated space The operating position is horizontal with the hatch facing downward The equipment will not be accessible during operation before accessing the means of connection or the inside of the equipment all electrical alimentation circuits of the equipment must be disconnected In the event of any questions contact the Technical Service or your distributor SAFETY The equipment should be examined every 90 days the structure fasteners movable parts mechanical cables electrical parts etc should be checked and lubricated if necessary Do notinstall this unit in an unstable place Do not alter neither modify this unit Do not use this unit in a bathroom neither near liquids or inflammable gases Donotconnecttheunit to an electrictension different from the one specified Do not force the storm doorin their opening or closing journey since the mechanics of the motor could be seriously damaged INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY
5. projection equipment will support an extra weight Reinforce the perimeter nextto the installation area Fig 4 with the accessories recommended by the manufacturer CHOOSE THE PLACE OF THE INSTALLATION The projectors do not have the same focus distance If you do not know the optic data of the projector readyto be installed proceed as follows Place the projector on a table Connect the electric current to the projector and switch on the projection equipment Leave it for a few minutes so that the projector reaches its maximum brightness Keeping the zoom control in the maximum opening bring the equipment closer to or move it further aw ay from the test wall that you have chosen until obtaining the desired screen image width In this case measure the distance between the lens and the image Put the zoomintheminimum opening and move the projector away until obtaining the same screen width than the obtained in the previous paragraph and measure the distance between the lens and the image Calculate the focal distance with the following formula Average optic center maximum zoom distance cm minimum zoom distance cm 2 The average optic centre determines the distance and the place to install the projector and in consequence Cinema Mirror You can get bigger precision if you deduct 20 cm of the journey from the projector lens to the active lens INSTRUCTIONSANDTIPS FORTHE INSTALL
6. AND INSTALLATION 3 1 5 meters INCLUDED ACCESSORIES Connection Cable 230 VA C Connector for push button Push button not included Graded plate User Manual DEFINITION AND FUNCTION OF COMPONENTS 3 Protection case of the electric equipment 6 Passive lens 4 Protection caseofthe mechanic equipment 7 Active lens 1 Variable position table 5 Connection of the pushing button and 8 Closing connecting rod and parallelism 2 Position control lever of the active lens connection 230 VAC 9 Leveling supports of variable height ADJUSTING SCREW INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION Cihema t mirror E figure 4 INSTALLATION PROCEDURE Cinema Mirror has been built with the knowledge of technical ceiling features For this reason it has leveling supports see Fig 3 Detail 9 that adapt to the T ceiling profiles and allow you to install it without the use of tools If the ceiling is made of plaster wood glass etc and it does not have profiles adapt a HC 60 60 model ceiling frame kit An aluminium profile designed to adapt ceilings to Cinema Mirror and give access to the interior of the ceiling see accessory page Order it from your distributor BEFORE PROCEEDING TO INSTALL The area where Cinema Mirror will be installed next to the
7. ATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION d Cinema ___ mirror E INSTALLATION UNPACKAGING AND PROCESS OF ASEMBLY Open the box of the Cinema Mirror and take out the protection butt plates Take out the plastic covers Take out the rubber of protection of the floodgate of the active mirror Place a fabric table cloth on a board table bench etc to protect and take care of the paintwork onthe equipment gate Separate the bevel from the gate and leave it ready to beinstalled later in the ceiling finish Leave Cinema Mirror on the table cloth Q Projectors do not always have the optic in the same place it can be to the left centred orto the right For this reason Cinema Mirror is equipped with a tray called variable position table Fig 5 The variable position table has5 positions 1 centred 2 moved to the left 3moved to the right 4 turned 1802 and centred and 5 turned1802 and to the right Remove the 6 screws that secure the table to the Cinema Mirror chassis Secure the variable position table with its screws in the best place so that the projector rests on its support feet Place the projector on the variable position table horizontally centred relative to the passive mirror This will be its working place ADJUSTMENT OF THE PASSIVE MIRROR To centre in h
8. L RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION T gt 9 E figure 8 H H FINAL FINISH OF THE CEILING Once we are definitively satisfied with the image obtained we will proceed to closethe ceiling with the same material used by the maker of thetechnical ceiling If you use other materials try to use materials with avery low weight Consult the possibilities of painting or masking ofthe material used for a correct simulation with the original ceiling ATTENTION PLEASE The motor system active door is not prepared to carry heavy loads as for example parts in wood cork glass etc that one might wantto install on the door as decoration items If you desire this tryto modify the finish by painting or imitating the painting by means of avery thin foil to be able to integrate the finish of the door of the Cinema Mirror to the roof decoration in which it is installed Take the measurements in which the gate was located with the frame measurements A and B Fig 8 Mark the measurements A and B on the technical ceiling plate 60x60cm or replacement material Place the bevel on the marks A and B and draw the contour lines With a cutting tool remove the space that must be occupied by the gate The installer should locate his working position in thesquare of thetechnical ceiling plate adjacent to the Cinema Mirror installation Move the Cinema Mirror projector set as much asisnecess
9. acing the place where the projection screen will beinstalled Place the chassis onto the T shaped profiles of the technical roof or the HC 60 60 frame Kit and make coincide the 2 2 leveling supports of the chassis Figure 3 detail 9 with the technical roof profile IF THE INSTALLATION IS NOT EQUIPPED WITH A WORKABLE TECHNICAL CEILING BUILD YOUR OWN SPACE USING THE HC 60 60 MODEL CEILING FRAME KIT see accessory page Now the height of the chassis can vary and can be levelled with the roof To level them please unfasten the screws of the leveling supports which holdsthe chassis and screed the latter to the same height of the surface of the roof Fasten again and strongly the screws ATTENTION PLEASE The motor system active door isnot prepared to carry heavy loads as for example parts in wood cork glass etc that one might want to install on the door as decoration items If you desire this try to modify the finish by painting or imitating the painting by means of a very thin foil to be able to integrate the finish of the door of the Cinema Mirror to the roof decoration in which itis installed Install the projector on the variable position table Place the projector optic as close to the passive mirror as possible Place the projector optic centred relative to the passive mirror Connect apushing button not included of 1A 230 VA C to the supplied entrance connector Insert the connector of the
10. ary to install the modified technical plate Place the Cinema Mirror projector set in the space chosen Lightly press the bevel pins outwards and adjust them to the gate Check the light image on the screen Provide the finishing touches to the ceiling finish according to the characteristic requirements of the space MAINTENANCE The mechanics and mobile parts of the equipment don t specify of a severe maintenance but if it is convenient the application of alubricantin the mobile parts with a minimum periodicity of 90 days Revise the electric installation and its connections likewise revise the anchorage from the unit to the roof The optic lenses will clean with non abrasive cloths using neuter soaps or simply with common water TECHNICAL FEATURES INSTRUCTIONS AND TIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION TECHNICAL SPECIFICATIONS dimensions in mm max 43 min 24 ACTIVE MIRROR DOOR Supply Power Starter push button not included Noise level False ceiling minimum height Maximum height of floodgate slope Mirror opening time Motor reducer Minimum dimension of the hole to embed Mechanical Dimensions mm Packed Dimensions mm Net weight Gross weight 230 VA C 50 Hz 10W Instantaneous 1 A to 230 V A C lt 15dB From 170 mm to 217 mm 265mm 30
11. eight the passive mirror Fig 3 detail 6 in relation to the lens of the projector remove thescrews that hold it to the chassis and move them up and down so that the centre of the mirror stays at the centre ofthe lens ofthe projector Tighten firmly but not to strong the axis of the mirror to the holes of the chassis to make possible an ulterior adjustment of the axis Place the graded plate supplied with the equipment on the Cinema Mirror profile Fig 6 1 figure 6 The passive mirror should be placed to 372 in relation to the base of the projector Please turn the passive mirror up so that the angles between the mirror and the template coindde in parallel Fasten stronglythe screws of the axis of the passive mirror INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION ELECTRICAL CONNECTION NOW CINEMA MIRROR IS READY TO BE INSTALLED IN THE CEILING INSTALLATION IN THE CEILING Remove the plate that coincides with the projector focal distance from the technical ceiling and leave it aside for its use later on the final finish ofthe ceiling If the ceiling is made of stucco wood glass etc install the HC60 60 ceiling frame kit beforehand Four T profiles to be assembled with its accessories so as to facilitate the perfect decorative finish of the ceiling Insert the Cinema Mirror with the optic mirrors f
12. follow conscientiously all the warnings and cautions that are described SAFETY RULES WARNING The equipment should be installed by installersspecialized in publiclocations Install and protect the line in accordance with the low tension electrical technical regulations as well asthe MIE BET 025 complementary technical instructions Installations in locations of public concurrence The equipment should be connected to ground protection All the required electric works of this equipment should be carried out by electricians qualified electronics or competent people according to the electrical technical regulations of each country The alimentation requires an automatic bipolar switch with MINIMUM 3 mm separation between contacts Flammable materials must not be placed within a radius of 1 meter of the equipment see instruction manual of video projector to be installed Secure and protect the alimentation cables and hoses gear material etc in such a way that they are not near moving parts or heat sources The equipment must be installed in the ceiling at a distance so that it is not within arms reach of a person Secured above the site itself or on a metallic bracket strong enough to hold theweight ofthe equipment plus the image projector The equipment should be secured to the bracket orthe ceiling using screws that must be able to withstand the weight of the equipment with the screw having a minimum diameter
13. o lowerthe image the control lever should be moved downward The motor actives and positions the active door as desired Repeat this operation until reaching the desired image height ATTENTION If the whole image is not represented on the projection screen this may be due to the fact that The projector zoom is closed eThe projector is very near the passive mirror The active mirror is excessively closed Correct these differences The image may not be parallel with the projection screen base due to height differences between the place of installation ofthe screen and that of the projector Fig 7A In the connecting rodsthat move the active mirror Fig 3 detail 8 there is a connecting rod active mirror regulation screw that corrects the defect If you wantto liftthe image move the connecting rod screw of the place affected upwards Fig 7B Rememberthe adjustmentelementsthat you have to obtain a cinema image Projector zoom and focus Vertically adjustable feet in the projector Trapeze correction manual automatic or electronic in the projector Passive mirror turn Active mirror movement Horizontal image control in the connecting rods Left right movement of the projection screen only some makers Regulation of the height extension of the projection screen nu U Ne o N INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERA
14. pushing button in the Cinema Mirror Connect the power source cable to the electric net and to protect with a bipolar ELECTRIC CURRENT INPUT switch not supplied with separation among contacts of 3 mm ELECTRIC DIAGRAM Connect the video DVD PC control signals etc following the instructions of the videoprojectormaker Secure the cables with flanges or plastic loops available in shops PHASE isn BROWN EARTH Cy YELLOW GREEN NEUTER N BLUE checking that they do not restrict the access and movement of the chassis on the technical ceiling Ts or supports Move the cables away from the area to facilitate the later handling of the videoprojector cleaning lamp replacement etc OPENING CLOSING BUTTON CONNECTION CLOSING SWITCH OPENING SWITCH povitneatneaeietatnny prtnnntennaatinene Perrier rere gt i i i _IMPULS RELAY Cinema t mirror E figure 7A figure 7B INSTRUCTIONSANDTIPS FORTHE INSTALLATION OF THE HC 37 53 MODEL CINEMA MIRROR GENERAL RECOMMENDATIONS FOR ASSEMBLY AND INSTALLATION HOW TO ADJUST THE IMAGE TO THE SCREEN ATTENTION DANGER Take out he rubber that blocks the door during the transport if you have not already made it before triggering the movement pushbutton ofthe active mirror gate make sure that there are no obstacles hindering its opening orclosing Do not
Download Pdf Manuals
Related Search