Manuale utente Virtual DS
Contents
1. Virtual DS logomat VIRTUAL DS USER MANUAL Rev 3 0 Table of Contents Introduction SOFTWARE FUNCTIONS 1 MAIN SCREEN 1 1 Reader Details Maze WING AMOG MMM oanaudaaesecsctusse cubase a a a aai 1 3 Capture list 2 ADDING AND REMOVING A READER Zils PAGING REAGE NM a cues R a T 2 2 Removing a Reader 3 READER PROPERTIES 3 1 Match code and Auto learning 92 COPIE 174 lL 5 KEE eT I gE RTI Te et a ST et OY Nn E ET 33 HIGN Speed Mod tnin ana aal ti ails a sil lalia ba ewes Gente alia ala 3 4 Counters Reset 35 2 23 11 1 1 111018 A EA TT pele eaccanebancc t 3 5 1 Region of interest 4 READERS SUMMARY 5 RECIPES 6 PROGRAM SEHINGS nr a aima luts oh anes e eae aata taamal es seen deat ein cecuteueccnsseicesiges 11 This document is propriety of LOGOMAT s r l 2 Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 Introduction In addition to being a practical guide forthe use ofthe Virtual DS software this manual outlines the main features of the software itself The Virtual DS software allows you to manage and monitor multiple network connected Datalogic Matrix 210 cameras Each camera can control several types of code both 1D and 2D including Code 39 UPC EAN Pharmacode Datamaitrix ECC 200 and QR Code SOFTWARE FUNCTIONS The software allows you to perform the following2. Capture list filter item allows you to filter the images displayed in the capture list of the main screen You can view all acquisitions the good codes only or the no good codes only 3 3 High Speed Mode The reader may need to operate at extremely high speeds In these cases the operator panel may not be able to handle data as accurately It is therefore necessary to set the high speed mode In this mode the data transmission channel between the reader and the operator panel is interrupted the images and values being no longer displayed but the reader continues ifs normal operation Even in this mode you can always access the properties and edit the operating parameters of the reader A lightning like icon f is displayed on the main screen and in the summary to signal that this mode is being used 3 4 Counters Reset The last property is the Counters reset item By tapping the corresponding action button and entering the password if required you can reset the values of all counters related to this reader 3 5 Picture Settings By using the action button of the Picture Settings item you can access the Picture Settings screen where you can edit parameters such as the lighting type exposure time gain and gain multiplier Picture Settings Internal Lighting Mode High Power Strobed Exposure x 100 Us 20 Gain Gain Increasing x1 AUTO TEST PANEL The Auto Test and Panel buttons are located at the bottom of the sc
3. 92 168 1 254 but will not find readers from other networks even if connected to the same machine 2 2 Removing a Reader To remove a reader from the list of connected readers use the Remove button The reader will continue to work as normal but it will be no longer displayed and its counters will be removed Moreover you will no longer be able to access and modify its operating parameters If you need to re check the removed reader you can add it back using the Add button This document is propriety of LOGOMAT s r l Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of 5 LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 3 READER PROPERTIES Reader properties Reader Name Picture Settings AR AIDA Match Code Operating Mode One Shot Trigger Ext Trig Trailing Edge Trigger Active State By selecting the Properties button you will access the screen shown in the figure This screen contains a list of the main reader settings such as the name match code operating mode input output symbols used and counters Some properties are enabled and disabled according to the set values For example if the operating mode is set to Single the settings for the reading in progress will be disabled 3 1 Match code and Auto learning When you tap the Match Code text field the program will ask if you wish to perform automatic learning By selecting the Yes button th
4. e reader Special characters enables or disables display of special characters within the code Some codes may use special characters that cannot be displayed such as for example the paragraph mark or the lt GS1 gt separator By enabling this option these characters will be displayed in their hexadecimal form If the option is disabled they will not appear Read code color indicates the colour of the text if disolayed Label background if enabled adds a background to the date time and read code to improve readability Network interface allows you to select the network card to be used You must set this option if the computer has multiple network cards Select the one to which the readers are connected Language allows you to select the language of the program text Password allows you to change the password used by the program for the operations requiring it DEFAULT PASSWORD Ad1023 This document is propriety of LOGOMAT s r l Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of 1 1 LOGOMAT s r l
5. e reader will take an automatic shot and display the value read in the appropriate text box To accept this setting press the OK button From this point on if the read code matches the one stored during this procedure each acquisition will return a good result otherwise it will return a no good result If you do not wish to automatically learn the code you can answer No to the auto learning request and manually enter the value of the code to be recognized It should be noted that the and 2 characters have a placeholder value and are therefore interpreted in a particular way The character means any text For example a match code like ABC XYZ will make all codes beginning with ABC and ending with XYZ such as ABC1XYZ ABC12XYZ and ABC123XYZ good but will make codes with a different beginning or ending such as 12XYZ or ABC 123 bad The 2 character means any character For example a match code like ABC XYZ will make codes beginning with ABC ending with XYZ but featuring a single character in the middle good In this case codes such as ABC1 XYZ ABCSXYZ and ABC7XYZ are good but codes such as ABC 12XYZ ABC 123XYZ and ABC 12 are not This document is propriety of LOGOMAT s r l 6 Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 3 2 Capture List Filter The
6. ge By tapping this button the reader switches to Live mode In this mode the reader acquires images in continuous mode and displays them on the screen This mode can be used for example to make mounting adjustments while always viewing the captured area To exit Live mode tap the Live button again 1 3 Capture list The capture list at the bottom of the screen allows you to view the last 50 captures of the selected reader The last 5 captures are always displayed To move through the list use the Previous and Following buttons To filter the captures refer to the appropriate item in the reader properties You can also delete the capture list at any time using the Reset list button This document is propriety of LOGOMAT s r l A Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 2 ADDING AND REMOVING A READER 2 1 Adding a Reader To connect a new reader use the Add button You can add the reader by directly entering the IP address or by performing an automatic search using the corresponding button Reader IP address Automatic search Cancel OK The automatic search finds readers in the operator panel network as long as they are properly configured For example if the operator panel belongs to the 192 168 1 x network the automatic search will find readers whose IP addresses range from 192 168 1 1 to 1
7. model number 212 110 212 110 IP Address 192 168 1 1 IP Address 192 168 1 2 Read 123456 i Read 123123 No read 7 No read 9 Good 123450 Good 123110 No good 6 No good 13 You can access this screen using the Summary button on the main screen In this section you can have an overall view of all connected readers with their main information You can add a new reader also from this section using the Add button It should be noted that if there is more than one connected reader this screen is displayed first upon starting the program To access the main screen of a reader select it by tapping the specific box This document is propriety of LOGOMAT s r l Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of 9 LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 5 RECIPES Recipes Recipe name Leaflets Symbology QR Code Match Code ABC123 Cartons Symbology QR Code Match Code XYZ456789 EI NEW SAVE SAVE AS LOAD ACTIVATE DELETE The Virtual DS software allows you to manage groups of settings and save them on a file so that they can be retrieved and transferred by the operator as necessary To do this access the Recipes screen using the dedicated button on the main screen By tapping the New button a new recipe will be created You can retrieve one of the previously saved recipes using the Open button The Save button is used to store the gr
8. operations e display and monitoring of multiple cameras at a time e display and editing of the main operating parameters of each camera e multiple programming of all cameras using recipes This document is propriety of LOGOMAT s r l Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of 3 LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 1 MAIN SCREEN Back button Forward button 13 11 2013 08 32 41 226 Information icon PROPERTIES inm z a Fa ARE lt Sao SS serine 08 32 20 928 08 32 26 066 08 32 30 009 08 32 37 977 08 32 41 226 All captures Followina P alr i From this screen you have an overall view of the selected reader Previous Reset list The last image acquired by the reader is displayed in the centre while the sequence of the latest captures is displayed at the bottom On the right there is the operations menu through which you can interact with the connected readers At the top you can see the name and the index of the reader to which we are connected You can move from one reader to another using the Forward and Back buttons 1 1 Reader Details By tapping the Information icon you can view detailed information on the selected reader such as the reader model firmware revision IP address MAC address and counters 1 2 Live Mode The Live button is displayed on the bottom left corner above the last acquired ima
9. oup of settings created on file The files are saved in the Virtual DS folder inside the My Documents folder The Save as button is used to store the group of settings too but with a different file name Using the Load button you can retrieve the values currently set on readers Using the Activate button the settings currently displayed are saved and transferred to the connected readers The Delete button deletes the selected recipe and the corresponding file This document is propriety of LOGOMAT s r l 10 Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 6 PROGRAM SETTINGS S otti n g c About Show capture date time Capture date time color SNOW read code Special characters Read code color Label background gt OFF Network interface 192169 1100 Language Italian The corresponding button on the main screen allows you to access the Settings screen Password The About button displays information about the Virtual DS software such as the version and contacts for assistance The list provides the program settings Show capture date time enables or disables display of the capture date and time on the main screen in the upper left corner Capture date time color indicates the colour of the text if displayed Show read code enables or disables display of the value of the code acquired by th
10. reen The Auto button will start the automatic image calibration procedure setting the values according to the best parameters evaluated by the reader based on the selected internal lighting mode The Test button will transfer the values set in the panel and take a shot with the newly transferred parameters You can then test the parameters and edit them from time to time before you confirm them using the OK button This document is propriety of LOGOMAT s r l Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of 7 LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 The Panel button moves the settings panel By default the panel is displayed above the image However for an overall view of the acquired image you can move the panel on the right side of the screen using this button 3 5 1 Region of interest User can also resize the region of interest in which the reader will try to read the code This operation increases the reader performance and reduces decoding time To do so resize the blu rectangle that wrap the camera picture moving each corner with the square shape markers This document is propriety of LOGOMAT s r l 8 Reproduction of all or any part of this document in any form is strictly forbidden without explicit permission of LOGOMAT s r l VIRTUAL DS USER MANUAL Rev 3 0 4 READERS SUMMARY Readers summary Leaflets CON Reader model number Reader
Download Pdf Manuals
Related Search