VJ1010, VJ121X MANUAL
Contents
1. Store indoors e Do not unplug by pulling on cord To unplug grasp the plug not the cord e Do not use with damaged cord plug or other parts e If your Wet Dry Vac is not working as it should has missing parts has been dropped or damaged left outdoors or dropped into water return it to an independent service center e Do not pull or carry by cord use cord as handle close a door on cord or pull cord around sharp edges or corners e Do not run Wet Dry Vac over cord e Do not handle plug or the Wet Dry Vac with wet hands e To reduce the risk of health hazards from vapors or dusts do not vacuum toxic materials e Do not use or store near hazardous materials e Do not use this Wet Dry Vac with a torn filter or without the filter installed except when vacuuming liquids as described in the operation section of this manual e Do not allow to be used as a toy Close attention is necessary when used by or near children e To reduce the risk of injury from accidental starting unplug power cord before changing or cleaning filter e Do not leave Wet Dry Vac unattended when plugged in Unplug from outlet when not in use and before servicing e Turn off Wet Dry Vac before unplugging e Do not put any object into ventilation openings Do not vacuum with any ventilation openings blocked keep free of dust lint hair or anything that may reduce air flow e Keep hair loose clothing fingers and all parts of body away from openings and movin2. ED INSTEAD OF GROUNDING NO GROUNDING MEANS IS PROVIDED ON A DOUBLE INSULATED APPLIANCE NOR SHOULD A MEANS FOR GROUNDING BE ADDED SERVICING A DOUBLE INSULATED WET DRY VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL REPLACEMENT PARTS FOR A DOUBLE INSULATED WET DRY VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE YOUR DOUBLE INSULATED WET DRY VAC IS MARKED WITH THE WORDS DOUBLE INSULATED AND THE SYMBOL D SQUARE WITHIN A SQUARE MAY ALSO BE MARKED ON THE APPLIANCE e To reduce the risk of electric shock unplug before cleaning or servicing e DO NOT use without filters in place CAUTION TO REDUCE THE RISK OF INJURY FROM MOVING PARTS UNPLUG BEFORE SERVICING EXTENSION CORDS When using an extension cord with your Wet Dry Vac refer to the following table to determine the required A W G wire size Before using the cleaner make sure the power cord and extension cord are in good working conditions Make repairs or replacements before using the vacuum cleaner Only use extension cords that are rated for outdoor use Length of Extension Cord 25 Feet 7 5 50 Feet 15 25 100 Feet 30 5 150 Feet 110V 120V Meter Meters Meters 45 7 Meters o ee te pu 4 UNPACKI NG AND CHECKING CARTON CONTENTS Remove entire contents of carton Check each item against the carton contents list Carton contents lists Key De SCDUON wi casccevtniwsncosensiccweens Qty A Vac Ass
3. ICALLY DISCLAIMS ANY IMPLIED WARRANTIES INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you SAFETY INSTRUCTIONS amp WARNINGS IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions before using this vacuum Read and understand this owner s manual and all labels on the Wet Dry Vacuum cleaner before operating Safety is a combination of common sense staying alert and knowing how your vacuum works Use this Wet Dry Vac only as described in this manual To reduce the risk of personal injury or damage to your Wet Dry Vac use only CHANNELLOCK recommended accessories For Household Use Only SAVE TH IS MAN UAL FOR FUTURE REFERENCE WARN I N G TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY e Do not run vac unattended e Do not vacuum or use this Wet Dry Vac near flammable liquids gases or explosive vapors like gasoline or other fuels lighter fluids cleaners oil based paints natural gas hydrogen or explosive dusts like coal dust magnesium dust grain dust or gun power Sparks inside the motor can ignite flammable vapors or dust e Do not vacuum anything that is burning or smoking such as cigarettes matches or hot ashes e Keep cord away from heated surfaces e Do not expose to rain
4. SI Z87 1 OR IN CANADA CSAZ94 3 BEFORE USING BLOWER CAUTION TO REDUCE THE RISK OF HEARING DAMAGE WEAR EAR PROTECTION WHEN USING THE VAC BLOWER FOR EXTENDED HOURS OR WHEN USING IT IN NOISY AREAS WARNING KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS WARNING WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED Verify that the power cord is disconnected from the outlet fig 1 Remove noise diffuser from the blower port fig 2 While squeezing the locking lever lift the detachable blower from the vacuum lid fig 3 amp 4 Insert the adaptor into the blowing port and fit it the desired extension wands and or nozzles fig 5 amp 6 Ensure the power switch is turned off and plug into the power supply fig 7 Firmly hold the blower before turning it on Turn the motor on by flipping the switch to the I ON position fig 8 DRN MAI NTENANCE 1 Verify that the power cord is disconnected from the outlet fig 1 2 Disconnect the hose from the unit fig 2 3 Undo the latches and remove the power head from the container fig 3 4 Clear all dirt or debris from the container and hose fig 4 5 Clean the foam filter by washing it with water and mild soap fig 5 6 Check the hose attachments and power cord to verify that they have not been damaged BLOWER INTAKE gt L O e a O aa After using the blower examine the bottom of the blower for debris and blockages and rem
5. TM Operator s Manual Wet Dry Vacuum with Detachable Blower 12 Gallon Model No VBV1210 FOR YOUR SAFETY Read and understand this manual before use Keep this manual for future reference W 3084514 CONFORMS TO UL STD No 1017 Certified to CSA STD aee o A www channellockproducts com Part No VR01BZ 20 96 01 TABLE OF CONTENTS SECTION PAGE Warranty aeei n aia aaae aaie a eia e aaa aa a a hia diane do aria E aE aA 2 Safety Instructions and WarningS ssesesessssssisrsisisrtisrtrtrtrtttrttitttrtrttnrsrersrtrsrsrrtent 3 Double Insulation Instructions esssssssrssrsnrsrrrrnsrrrrerrrnrnstrrnsrnterntanrnrananrnrnennrnrnen 4 Extension Gordi eaa a E E A E aaa S Soe eae E A E aT 4 Unpacking and Checking Carton Contents ies osaeucguted usar aguaderseusaabeacaens badestouderecueownegueges 5 General Assembly Instructions 0202 0 chsa acest eax ede ae nian adie ade aera 6 Dry Vacuum Operation aa ctvvsdnriverraseeceteraondal oe die Dube toua stone Men aerate sues daiwa Liquid Vacuum Operation ox scicce ceisies aie see dacs Sis te rene terested eh aden Cae ee nae er ae eine 8 Blowing Operation aese ara a eai Sa ETEA Aa Genego say A MeN ace es EDENE 9 Mantena O a se Loa a a a a Eea AA tated tha Miocene ce a eae elas 9 Installing amp Cleaning Cartridge Filter ceccceeececeeeeeeeeeeeee eee sansa een ese estes eeegeaeeeeeaees 10 Installing amp Cleaning Foam Sleeve Filter ceccceeeeeeeeeeeeeceeeee
6. ded power cord and grounded power supply system DRY VACUUM OPERATION DRY VACUUMING WARNING BE SURE TO READ UNDERSTAND AND APPLY INFORMATION ENTITLED SAFETY INSTRUCTIONS amp WARNINGS DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES VAPORS OR EXPLOSIVE DUSTS IN THE AIR FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO LIGHTER FLUID SOLVENT TYPE CLEANERS OIL BASE PAINTS GASOLINE ALCOHOL OR AEROSOL SPRAYS EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO COAL MAGNESIUM GRAIN OR GUN POWDER TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST DO NOT VACUUM TOXIC MATERIALS 1 Verify that the power cord is disconnected from the outlet fig 1 2 In order to prepare your vacuum for dry vacuuming verify that the cartridge filter is securely mounted Make sure the filter is pushed in until it stops against the power head fig 2 Your Wet Dry Vac comes with the cartridge filter pre installed if not see page 10 for installation instructions 3 Place filter retainer on top of cartridge filter and tighten down by turning the retainer handle clockwise fig 3 4 Place the power head back on the container aligning the top section with the latches and snap into place fig 4 OPERATING INSTRUCTIONS DRY VACUUMING 5 Insert the locking end of the hose into the vacuum port on the front of the tank and lock in place Push the required attachment onto the free end of the hose or extension fig 5 6 Plug i
7. e Assembly 1 15 TvaTxk oz o2 Vacuum Port Defector 4 VRO1PF 20 20 Power Head Blower Assembly 16 vro1ez 20 96 01 Operators Manual 1 VROIPF 10 08 Blower Filter 17 Fv6823 01 00 Hose tt 10 18 Fv6772 01 01 UtilityNozzle 01PF 10 09 VR21PF 20 20 ContainerLid 19 _ Fv6771 02 01__ Blower Nozzle i 20 _ Fv6901 01 01 Extension Wands a A 4 1 za vso1PF 13 00 Float amp FilterCage 1 g 1 21 vuospF 1200 Noise Diffuser 1 Em n cme n 4 a 6 Cee 8 Fv9546 02 00_ 9 Fv9546 01 20 22 Fvgso1 01 00 _ Foamsleeve 4 t 23 Fv6771 03 01 Car Nozzle 14 m Everrioror Crevice oor e Ce a 25 Fvesst 0401 Adaptor 1 Sy PE ee Cartridge filter Filter Retainer VROIPF 30 01 Container VB0IPF 2001 Draincap TvaTsi 18 00 Caster TVQTJC 14 00 Caster Foot 12
8. e eee eceeee entree eneeaaeeeeeges 11 TLOUBDIESNOOLING so iseer ca avian bal ne RU Aix eres cede E nian aoe ree date EE neest hs 11 Exploded View and Parts List ccecceeeeee eee ee ee eee ee eee ee eee ea ee esa sees sa ea ee eeeeeeeesaeeenegs 12 Thank you for purchasing this CHANNELLOCK wet dry vacuum cleaner Feel confident that with CHANNELLOCK you are obtaining a high quality product engineered for optimal performance This vacuum is capable of picking up liquids and dry materials FOR YOUR SAFETY CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS WARRANTY CHANNELLOCK takes pride in producing a high quality durable product This CHANNELLOCK product carries a limited two 2 year warranty against defects in workmanship and materials from date of purchase under normal household use If product is to be used for commercial industrial or rental use a 90 day limited warranty will apply Warranty does not apply to defects due to direct or indirect abuse negligence misuse accidents repairs or alterations and lack of maintenance Please keep your receipt as proof of purchase This warranty gives you specific legal rights and you may have other rights which vary form state to state For product service call Customer Service at 866 384 8432 DO IT BEST CORP IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE THE LIMITED WARRANTY IS THE ONLY WARRANTY THAT APPLIES TO THIS PRODUCT AND DO IT BEST CORP SPECIF
9. embly 1 B OSC iesin ne tancke tetera canain 1 C Utility Nozzle 1 D Caster Foot W Accessory Storage 4 E OS eer F 4 Screws Bag 1 G Foam Sleeve Filter 0 H Extension Wand 2 Car Claw ccccceceeeeeeeeeeeeeeees 1 J Concentrator Nozzle 65 1 K Crevice TOOl cceceeeeeeeeeees 1 L Cartridge Filter c eseeeeee 1 M Filter Retainer 0 ceeseeeees 1 N Adaptor 1 O DiffUS P 0 eeeceeee eneren 1 P Operators Manual 0 1 NOTE The hose and accessories for this vacuum are 2 5 inch diameter Cord Hook On Off Switch Handle Blowing Port Power Head Accessory Storage AON GA SA D mr Container Lid Cord Hook Latch an Vaccum Port Container Accessory Storage Caster Foot Blower Release Button Caster Drain 5 GENERAL ASSEMBLY INSTRUCTIONS A Philips head screw driver is required D WARNING DO NOT PLUG IN POWER CORD TO POWER OUTLET MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET DRY VAC UNPACKING YOUR WET DRY VACUUM amp GENERAL ASSEMBLY 1 Verify that the power cord is disconnected from the outlet fig 1 Undo the latches fig 2 2 3 Lift the power head off the container fig 3 4 Remove the contents from inside the container make sure you have all contents as listed on page 5 fig 4 5 Turn the container upside down and inser
10. g parts e To reduce the risk of falls use extra care when cleaning on stairs When using as blower e Direct air discharge only at work area e Do not use Wet Dry Vac as a sprayer e Do not direct air at bystanders e Keep children away when blowing e Wear safety goggles DOUBLE I NSULATION INSTRUCTIONS This Wet Dry Vac is double insulated eliminating the need for a separate grounding system Use only identical replacements parts Read the instructions for Servicing Double Insulated Wet Dry Vacs before servicing Use this Wet Dry Vac as described in this manual Observe the following warnings that appear on the motor housing of your Wet Dry Vac DOUBLE INSULATED GROUNDING NOT REQUIRED WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE TO RAIN STORE INDOORS WARNING FOR YOUR OWN SAFETY READ AND UNDERSTAND OPERATOR S MANUAL DO NOT RUN UNATTENDED DO NOT PICK UP HOT ASHES COALS TOXIC FLAMMABLE OR OTHER HAZARDOUS MATERIALS DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS CAUTION e Do not vacuum drywall dust or fireplace soot or ash with standard Wet Dry filter This is a very fine dust which will not be captured by the filter and may cause damage to motor When vacuuming fine dust use a fine dust filter sold separately WARNING SERVICING OF DOUBLE INSULATED WET DRY VACUUMM WITH A DOUBLE INSULATED WET DRY VACUUM TWO SYSTEMS OF INSULATION ARE PROVID
11. n the power cord into the outlet fig 6 7 Turn the motor on by flipping the switch to the l ON position fig 7 8 Once you have completed vacuuming flip the switch to the O OFF position and unplug the power cord from the outlet O OFF ON DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING LI QUI D VACUUM OPERATION LIQUID VACUUMING WARNING BE SURE TO READ UNDERSTAND AND APPLY INFORMATION ENTITLED SAFETY INSTRUCTIONS amp WARNINGS DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES VAPORS OR EXPLOSIVE DUSTS IN THE AIR FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO LIGHTER FLUID SOLVENT TYPE CLEANERS OIL BASE PAINTS GASOLINE ALCOHOL OR AEROSOL SPRAYS EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO COAL MAGNESIUM GRAIN OR GUN POWDER TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST DO NOT VACUUM TOXIC MATERIALS WARNING DO NOT PLUG IN POWER CORD TO POWER OUTLET MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET DRY VAC 1 Verify that the power cord is disconnected from the outlet fig 1 Verify that the container is clean and free of dust and dirt 2 Remove cartridge filter then carefully install the foam sleeve filter over the filter cage and place the power head back on the container fig 2 See filter installing instructions on page 11 DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING OPERATING INSTRUCTIONS WET VACUUMING 3 Fit the desired n
12. ntly tapping or brushing dirt off Cleaning should not be done indoors in living areas For optimal performance a new filter is recommended 4 Install cleaned or new filter into place as instructed above in steps 2 and 3 of Installing Cartridge Filter 5 Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage 10 IMPORTANT Clean or change the cartridge filter regularly for best performance ALWAYS USE CARTRIDGE FILTER FOR DRY VACUUMING If the machine is used with out the cartridge filter the motor will burn out and the warranty will be voided Always keep spare filters on hand NOTICE The filters included are made of high quality materials designed to stop small dust particles The cartridge filter should be used for dry pick up only A dry cartridge filter is necessary to pick up dust If the cartridge filter is wet it will clog quickly and be very difficult to clean Handle the filter carefully when removing it for cleaning and replacing it Check the filters for tears or small holes a small hole can let dust pass through and out of the cleaner Do not use a filter with holes or tears replace it immediately INSTALLING amp CLEANING FOAM SLEEVE FILTER Installing Foam Sleeve Filter On fig 2 amp 3 Verify that the power cord is disconnected from the outlet fig 1 Remove power head and place in upside down position Follow instructions to remove cloth filter Carefull
13. ove if found To clean the foam pad of the intake 1 Verify that the power cord is disconnected from the outlet fig 1 WARNING ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING THE POWER HEAD FROM THE CONTAINER Remove the four screws holding the intake shield and lift off the shield fig 2 Remove the foam pad from the blower and clean the foam pad with soapy water and allow to dry fig 3 Check the foam pad for reuse If you need to replace the foam pad consult the parts list of the manual Replace the foam pad on to the blower aligning the wholes to the screw tabs fig 4 Reinstall the intake shield and the four screws fig 5 ou WP INSTALLING amp CLEANING CARTRIDGE FILTER Installing Cartridge Filter 1 Verify that the power cord is disconnected from the outlet 2 Remove lid and power head and place in upside down position 3 Install the cartridge filter over the filter cage with the flat end of the filter towards the vacuum lid Carefully push filter in until it stops against the lid fig 2 amp 3 4 Place filter retainer on top of cartridge filter over the raise lip and tighten down by turning retainer clockwise do not over tighten fig 3 amp 4 Removing and Cleaning Cartridge Filter 1 Unlock and remove the filter retainer by tuning retainer handle counter clockwise 2 Carefully hold and pull the cartridge filter up for removal fig 6 3 Clean the cartridge filter by ge
14. ozzle to the vacuum hose fig 3 4 Verify that the switch is in the O OFF position before plugging the power cord into the outlet fig 4 5 Turn the motor on by flipping the switch to the P ON position fig 5 6 After use empty the container by unscrewing the drain cap Drain liquids into a suitable receptacle or drain Remember to refit the drain cap to the container after draining container fig 6 IMPORTANT When vacuuming large quantities of liquids do not immerse the nozzle completely in the liquid leave a gap at the tip of the nozzle opening to allow air inflow The machine is fitted with a float valve that stops the suction action when the container reaches its maximum capacity You will notice an increase in motor speed When this happens turn off the machine disconnect from power supply and drain the liquid into a suitable receptacle or drain To continue vacuuming refit the container with the drain cap After wet vacuuming turn the machine off and remove plug from power supply Empty the container clean and dry the inside and outside before storage REMEMBER The foam filter must be removed after wet vacuuming and a cartridge filter must be installed before dry vacuuming again This Wet Dry Vac converts to a detachable blower that can be used for leaf blowing in yards decks and patios To use the detachable blower feature follow the instructions listed WARNING ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH AN
15. t the four caster feet into the slots on the container and tighten with supplied screws Verify that the casters are mounted correctly Do not over tighten screw fig 5 6 Your vacuum comes ready for dry vacuum cleaning If cartridge filter is not installed refer to page 10 for filter installation fig 6 amp fig 7 7 For wet vacuum cleaning install the supplied foam filter fig 8 See page 11 for filter installation 8 Place the power head back on the container aligning the top section with the latches and snap into place Keep in mind to position the power head so that the blower port is towards the rear fig 9 9 Insert the locking end of the hose into the port of the container and lock in to place fig 10 10 Choose the desired wands or accessories and push onto the hose fig 11 NOISE DIFFUSER For quiet operation during vacuuming install the noise diffuser into the blower port by inserting the locking end of the diffuser into the blower port and turning clockwise to lock into place POLARIZED PLUG To reduce the risk of electrical shock this appliance has a polarized plug one with the blade wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Double insulation o eliminates the need for the three wire groun
16. y slide foam sleeve filter down over the filter cage making sure the whole cage is covered 4 Replace the power head on to the container Cleaning Foam Sleeve Filter 1 With the removed power head in the upside down position carefully remove foam sleeve filter fig 4 2 Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water fig 5 3 Allow filter to air dry before installing and using again TROUBLESHOOTING WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK UNPLUG BEFORE TROUBLESHOOTING Symptom Possible Causes Corrective Action Vacuum will not operate 1 No power supply 1 Check power supply cord breakers fuses 2 Faulty power cord 2 Unplug and check the power cord If damaged have it repaired by a professional 3 Container full 3 Empty container Dust comes out from motor cover 1 The cartridge filter is missing or damaged 1 Attach or replace cartridge filter Reduced efficiency and motor speed vibration 1 There is a blockage in the nozzle hose or the container inlet The cartridge filter is clogged by fine dust 1 Check nozzle hose and container inlets for blockage Take off the filter and clean it Or install a new cartridge filter EXPLODED VIEW AND PARTS VBV1210 Manual Parts List 1 wopate o1 12 Power Switch 14 14 TVQTXK 06 01__ Vacuum PortAssembly 4 2 VRoIPF 10 10_ Handi
Download Pdf Manuals
Related Search