Home

manual

1. rates are set to 100 Then bind your receiver to the transmitter Initial transmitter EPA servo travel adjust settings pitch elevator 50 roll aileron 50 yaw rudder 100 Connecting your receiver to the flight control board Connect your throttle aileron elevator and rudder channels to the appropriately labeled ports on the flight control board see photos below for reference Direction of Forward Flight Roll Gyro Gain te S W V4 7 Pitch Gyro Gain Adjust Atmega328PA IC Yaw Gyro Gain Adjust In System Programming AIL ELE THR RUD ISP Header White Signal Receiver sold separately IMPORTANT ESC throttle range calibration Turn yaw pot to zero Turn on transmitter Move throttle stick to full position Turn on flight controller Wait until the ESC s beep twice after the initial beeps Plush ESCs Move throttle stick to low position ESCs beep Turn off flight controller Restore the yaw pot Checking transmitter channels Turn on transmitter and flight controller Set throttle to about 1 4 Motors should start Move pitch elevator stick forward Back motors should speed up If not reverse pitch elevator channel Move roll aileron stick to the left Right motors should speed up If not reverse roll aileron channel Move yaw rudder stick to the left Front and back motors should speed up If not reverse yaw rudder channel Ch
2. TURNIGY power systems Integrated PCB Micro Quad PNP WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result serious injury or damages to personal property This model is NOT a toy and It must be operated with caution Seek assistance from an experienced modeler if you are not confident with remote control models This product must not be operated by children without the supervision of a responsible adult As the user of this product you are solely responsible for damages to the product property or others This model is controlled by a radio signal subject to interference from many sources outside your control This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury e Never operate your model with low transmitter batteries e Always operate your model in an open area away from cars traffic or people e Carefully follow the directions and warnings for this and any optional support equipment chargers battery packs radio equipment etc e Keep all small parts and anything electrical out of the reach of children e Moisture causes damage to electronics Avoid water exposure to all equipment not specifically designed Do Not work on your Micro Quad while the battery is plugged in D
3. ard by holding the Yaw rudder stick full right Slowly increase throttle until your quad lifts off After landing be sure to disarm your quad by holding the yaw rudder stick full left NOTES Propeller Installation Install the propellers see photo below for reference Be sure to install propellers in the correct rotation direction see photo below for reference DO NOT INSTALL PROPELLERS UNTIL THE FINAL STAGE DO NOT WORK ON YOUR QUAD WHILE THE BATTERY IS PLUGGED IN
4. ecking gyro directions Turn on transmitter and flight controller Set throttle to about 1 4 Motors should start Tilt quad forward Forward motors should speed up If not reverse pitch gyro see next section for gyro reversing instructions Tilt quad to the left Left motors should speed up If not reverse roll gyro see next section for gyro reversing instructions Turn quad CW Front and back motors should speed up If not reverse yaw gyro see next section for gyro reversing instructions Reversing gyros if required 1 Set roll gain pot to zero Turn on flight controller LED flashes rapidly 10 times Move the stick for the gyro you want to reverse LED will blink continually Turn off flight controller If there is more gyros to be reversed go to step 2 otherwise set roll gain pot back NOU BRWN Pre Flight Check Transmitter throttle adjusting Turn on transmitter and flight controller If LED does not turn on and stay on lower your throttle trim If still no go you may need to reverse the throttle channel On Quad v4 7 firmware or above you need to arm your board by putting the left stick down and to the right for the LED to come on If this does not happen adjust your throttle and yaw trim down and to the right on your transmitter Lift off procedure Install propellers See Propeller Installation Place the quad on a flat surface Ensure it is safe to fly and arm the bo
5. o Not install the propellers until the final stages are complete and you are ready for the first flight Specification Width 250mm Height 85mm Motor 4 x Turnigy T1811 2900kv Brushless ESC 4 x Turnigy Plush 6A Props 4x 5x3 inch 2CW amp 2CCW Controller Hobbyking Multi Rotor Control Board X configuration Included in box 1 x Turnigy Integrated PCB Plug and Fly Micro Quad motors ESCs control board pre installed 4 x Propellers 2CW amp 2CCW 4 x Servo extension leads for connecting receiver to control board Required 500 900mAh 2S 7 4V Lipoly Battery 4 channel transmitter and receiver Battery Charger User Guide Thank you for purchasing the Turnigy Integrated PCB Plug and Fly Micro Quadcopter This PNF quad takes all of the guesswork out of choosing your electronics arriving with the motors ESCs and multi rotor control board pre installed You simply need to add your own 4ch transmitter receiver system 500 900mAh 7 4V lipoly battery and this quad is ready to fly The Turnigy PNF Micro Quadcopter comes pre setup out of the box but you will still need to configure your transmitter and conduct a pre flight check before attempting to fly Please follow the instructions below prior to your first flight with this model Setting up your transmitter Create a new model memory fixed wing mode and make sure that all mixes are disabled all trims are neutral and that all End Point Adjustments EPA and D R dual

manual

Contents

Download Pdf Manuals

Related Search

Related Contents