GT23 General Description
Contents
1. 5 3 Mounting Position When mounting the GOT the following clearances must be maintained from other structures and devices Some cables may need to be longer than the specified dimensions when connecting to the GOT Therefore consider the connector dimensions and bending radius of the cable as well for installation For the lead in allowance for cables at the bottom of the GOT refer to the GOT2000 Series User s Manual Hardware Us Panel thickness 1 6 to 4mm 0 06 to 0 16 inch According to the dimensions in the following table leave clearances between the GOT and the other devices The values enclosed in square brackets apply to the case where no other equipment generating radiated noise such as a contactor or heat is installed near the GOT However keep the ambient temperature of the GOT to 55 C or lower Unit mm inch C When the SD card is not used When the SD card is used GT2310 50 1 97 48 1 89 78 3 07 or more 50 1 97 50 1 97 100 3 94 or more or more 20 0 79 or or more or more or more 18 0 71 18 0 71 or more 20 0 79 or 20 0 79 or 20 0 79 or or more more GT2308 more more more 50 1 97 or more 1 When opening or closing the battery cover 72 2 83 or more 5 4 Control Panel Inside Temperature and Installation Angle When installing the GOT to a panel set the display section as shown below Using the GOT with the install2. static electricity from human body etc Not doing so can cause the unit to fail or malfunction Use the battery manufactured by Mitsubishi Electric Corporation Use of other batteries may cause a risk of fire or explosion Dispose of used battery promptly Keep away from children Do not disassemble and do not dispose of in fire Be sure to shut off all phases of the external power supply before replacing the battery or using the dip switch of the terminating resistor Not doing so can cause the unit to fail or malfunction by static electricity TOUCH PANEL PRECAUTIONS CAUTION For the analog resistive film type touch panels normally the adjustment is not required However the difference between a touched position and the object position may occur as the period of use elapses When any difference between a touched position and the object position occurs execute the touch panel calibration When any difference between a touched position and the object position occurs other object may be activated This may cause an unexpected operation due to incorrect output or malfunction PRECAUTIONS WHEN THE DATA STORAGE IS IN USE 7 WARNING Ifthe SD card mounted on drive A of the GOT is removed while the GOT is accessed processing for the GOT might be interrupted about for 20 seconds The GOT cannot be operated during this period The functions that run in the background including a screen updating alarm logging scr
3. Directive s requirements for isolation between the primary and secondary circuits 2 Insulation requirements Dielectric withstand voltages are shown in the following table Reinforced Insulation Withstand Voltage Installation Category II source IEC664 Rated voltage of hazafdo s Surge withstand voltage 1 2 50us voltage area 150 VAC or below 2500V 300 VAC or below 4000V 4 3 EMC Directive Compliant System Configuration 4 3 1 GOT Use any of the GOTs with which CE mark logo is printed on the rating plate All GT23 models support the EMC Directive 4 3 2 Cables Modify the cables including user produced cable to ensure compliance with the EMC Directive For details refer to Section 4 4 2 In addition for the cables to be used refer to the GOT2000 Series Connection Manual 4 4 EMC Directive Compliant System Configuration Wire and connect the GOT2000 series equipment as instructed below If the GOT2000 series equipment is configured in a way different from the following instructions the system may not comply with the EMC Directive 4 4 1 Power and ground wires wiring method 1 Power and ground wires wiring method Connect the power wire and connection cable as shown in the illustration Lead the power wire and ground wire as shown in Section 4 1 2 2 Be sure to ground the LG cable and FG cable 100 240VAC GOT power section 24VDC GOT power section INPUT INPUT Jioo 2aovecch L 24VDC oh LS
4. J gt 166 6 54 olm 2 oO Unit mm inch 4 EMC AND LOW VOLTAGE DIRECTIVE For the products sold in European countries the conformance to the EMC Directive which is one of the European Directives has been a legal obligation since 1996 Also conformance to the Low Voltage Directive another European Directives has been a legal obligation since 1997 Manufacturers who recognize their products must conform to the EMC and Low Voltage Directive are required to declare that their products conform to these Directives and put a CE mark on their products Authorized representative in Europe Authorized representative in Europe is shown below Name Mitsubishi Electric Europe BV Address Gothaer strase 8 40880 Ratingen Germany 4 1 Requirements to Meet EMC Directive EMC Directives are those which require any strong electromagnetic force is not output to the external Emission electromagnetic interference and It is not influenced by the electromagnetic wave from the external Immunity electromagnetic sensitivity Items4 1 1 through4 4 3 summarize the precautions to use GOT and configure the mechanical unit in order to match the EMC directives Though the data described herein are produced with our best on the basis of the requirement items and standards of the restrictions gathered by Mitsubishi they do not completely guaranteed that all mechanical unit manufactured according to the data do
5. Shanghai 200003 China Tel 86 21 6120 0808 Taiwan Setsuyo Enterprise Co Ltd 6F No 105 Wu Kung 3rd Rd Wu Ku Hsiang Taipei Hsine Taiwan Tel 886 2 2299 2499 Korea Mitsubishi Electric Automation Korea Co Ltd 1480 6 Gayang dong Gangseo ku Seoul 157 200 Korea Tel 82 2 3660 9552 Singapore Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Tel 65 6470 2460 Thailand Mitsubishi Electric Automation Thailand Co Ltd Bang Chan Industrial Estate No 111 Moo 4 Serithai Rd T Kannayao A Kannayao Bangkok 10230 Thailand Tel 66 2 517 1326 Indonesia P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 P O Box 5045 Jakarta 11050 Indonesia Tel 62 21 6630833 India Messung Systems Pvt Ltd Electronic Sadan NO III Unit No15 M I D C Bhosari Pune 411026 India Tel 91 20 2712 3130 Australia Mitsubishi Electric Australia Pty Ltd 348 Victoria Road Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifications subject to change with
6. doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction DESIGN PRECAUTIONS A CAUTION Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm apart Not doing so noise can cause a malfunction Do not press the GOT display section with a pointed material as a pen or driver Doing so can result in a damage or failure of the display section When the GOT is connected to the Ethernet network the available IP address is restricted according to the system configuration When multiple GOTs are connected to the Ethernet network Do not set the IP address 192 168 3 18 for the GOTs and the controllers in the network e When a single GOT is connected to the Ethernet network Do not set the IP address 192 168 3 18 for the controllers except the GOT in the network Doing so can cause the IP address duplication The duplication can negatively affect th
7. shut down the noise generated from GOT on the control panel 1 Control Panel a The control panel must be conductive b When fixing a top or bottom plate of the control panel with bolts do not coat the plate and bolt surfaces so that they will come into contact And connect the door and box using a thick grounding cable in order to ensure the low impedance under high frequency c When using an inner plate to ensure electric conductivity with the control panel do not coat the fixing bolt area of the inner plate and control panel to ensure conductivity in the largest area as possible d Ground the control panel using a thick grounding cable in order to ensure the low impedance under high frequency e The diameter of cable holes in the control panel must be 10cm 3 94in In order to reduce the chance of radio waves leaking out ensure that the space between the control panel and its door is small as possible Paste the EMI gasket directly on the painted surface to seal the space so that the leak of electric wave can be suppressed Our test has been carried out on a panel having the damping characteristics of 37dB max and 30dB mean measured by 3m method with 30 to 300MHz 2 Connection of power and ground wires Ground and power supply wires for the GOT must be connected as described below a Provide a grounding point near the GOT Short circuit the LG and FG terminals of the GOT LG line ground FG frame grou
8. the screws or the GOT WIRING PRECAUTIONS CAUTION Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction Plug the communication cable into the GOT interface or the connector of the connected unit and tighten the mounting screws and the terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit TEST OPERATION PRECAUTIONS 7 WARNING Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident STARTUP MAINTENANCE PRECAUTIONS 7 WARNING When power is on do not touch the terminals Doing so can cause an electric shock or malfunction Correctly connect the battery connector Do not charge disassemble heat short circuit solder or throw the battery into the fire Doing so will cause the battery to produce heat ex
9. FG H IRS CACO gt i m A a A 90mm or less 90mm or less 4 4 2 Processing connection cables Process the cable used with the GOT with the following method When processing the cable ferrite core and cable clamp are required The cable clamp used by Mitsubishi Electric for the EMC specification compatibility test is shown below e TDK corporation brand ZCAT3035 1330 Ferrite Core e Mitsubishi Electric Model AD75CK cable clamp e Japan Zipper Tubing Co Ltd Zipper tube SHNJ type 1 Ethernet connection Strip the outer insulation layer at both ends of the cable by the length shown below to expose the braided shield for grounding For grounding with cable clamps refer to Section 4 4 3 GOT side PLC personal computer side E 230 or less gle le 400 or less 9 06 15 75 Unit mm inch 2 CPU direct connection e Attach ferrite cores to the cable in the positions as illustrated below GOT side Ferrite Core PLC side ZCAT3035 1330 m m ae eee im 1 100 or less f T00 or less 3 94 M 3 94 Unit mm inch 3 Computer link connection e Peel the sheath with t
10. are MSE GT23 General Description GT2310 VTBD GT2308 VTBD GT2310 VTBA GT2308 VTBA Thank you for purchasing the GOT2000 Series Prior to use please read both this manual and the detailed manual thoroughly to fully understand the product MODEL GT23 U GD E Model code GOTE OOO IB NA 0800503ENG B 1309 MEE 1D7Ml4 ISAFETY PRECAUTIONSI Always read these precautions before using this equipment Before using this product please read this manual and the relevant J manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this prod uct In this manual the safety precautions are ranked as WARNING and CAUTION Indicates that incorrect handling may cause WARNING _ hazardous conditions resulting in death or l severe injury l Indicates that incorrect handling may cause l i CAUTION hazardous conditions resulting in medium or slight personal injury or physical damage j Note that the A CAUTION level may lead to a serious accident according to the circumstances Always follow the instructions of both levels because they are impor tant to personal safety Please save this manual to make it accessible when required and always forward it to the end user DESIGN PRECAUTIONS WARNING Some failures of the GOT communication un
11. ation angle other than the following deteriorates the GOT earlier When installing the GOT with the installation angle between 60 to 105 the temperature inside the control panel must be within 55 C When installing the GOT with the installation angle other than between 60 to 105 the temperature inside the control panel must be within 40 C Display section GOT K A e Panel or others J 6 MAINTENANCE AND INSPECTION Refer to the GOT2000 Series User s Manual Hardware for maintenance and inspection for the GOT Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties A For safe use e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the pr
12. between line and ground 0 5kV Power line between lines 0 5kV Data communication port 1kV Immunity test in IEC61000 4 6 which a noise Conducted RF inducted on the immunity power and signal lines is applied Power line 10V Data communication port 10V Test for checking normal operations under the circumstance exposed to the ferromagnetic field noise of the power supply frequency 50 60HZ IEC61000 4 8 Power supply frequency magnetic field immunity IEC61000 4 11 Instantaneous power failure and voltage dips immunity AC power type 0 5 cycle 0 interval 1 to 10s 250 300 cycle 0 10 12 cycle 40 25 30 cycle 70 Test for checking normal operations at instantaneous power failure 1 The GOT is an open type device device installed to another device and must be installed in a conductive control panel The above test items are conducted in the condition where the GOT is installed on the conductive control panel and combined with the Mitsubishi PLC 2 QP Quasi Peak Quasi peak value Mean Average value 3 The above test items are conducted in the following conditions 30M 230MHz QP 40dBu V m 10m in measurement range 230M 1000MHz QP 47dBuV m 10m in measurement range 4 1 2 Control panel The GOT is an open type device device installed to another device and must be installed in a conductive control panel It not only assure the safety but also has a large effect to
13. e GOT in the environment of oil or chemicals use the protective cover for oil Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT WIRING PRECAUTIONS N WARNING Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions CAUTION Make sure to ground the FG terminal and LG terminal of the GOT power supply section to the protective ground conductors dedicated to the GOT with a ground resistance of 100 Q or less When tightening the terminal screws use a Phillips head screwdriver No 2 Terminal screws which are not to be used must be tightened always at torque 0 5 Nem to 0 8 Nem Otherwise there will be a danger of short circuit against the solderless terminals Use applicable solderless terminals and tighten them with the specified torque If any solderless spade terminal is used it may be disconnected when the terminal screw comes loose resulting in failure Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product Not doing so can cause a fire or failure Tighten the terminal screws of the GOT power supply section in the specified torque range 0 5 Nem to 0 8 Nem Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of
14. e application method of the Low Voltage Directive and the product compatibility 4 2 1 Standard subject to GOT Standard applied to GOT EN61131 2 Programmable controllers Equipment requirements and tests EN60950 1 Safety of Information Technology Equipment 4 2 2 Power supply The insulation specification of the GOT was designed assuming installation category Il Be sure to use the installation category II power supply to the GOT The installation category indicates the durability level against surge voltage generated by lightning strike Category has the lowest durability category IV has the highest durability 2 Category IV Category Ill Category II Category Installation category Category II indicates a power supply whose voltage has been reduced by two or more levels of isolating transformers from the public power distribution 4 2 3 Control panel Because the GOT is open type equipment device designed to be stored within another device be sure to use it only when installed in a control panel 1 Shock Protection In order to prevent those who are unfamiliar with power facility e g an operator from getting a shock make sure to take the following measures on the control panel a Store the GOT within the control panel locked and allow only those who are familiar with power facility to unlock the panel b Build the structure in order that the power supply will be shut off when the contr
15. e communication of the device with the IP address 192 168 318 The operation at the IP address duplication depends on the devices and the system Turn on the controllers and the network devices to be ready for communication before they communicate with the GOT Failure to do so can cause a communication error on the GOT When the GOT is subject to shock or vibration or some colors appear on the screen of the GOT the screen of the GOT might flicker Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT main unit to from the panel Not doing so can cause the unit to fail or malfunction Use the GOT in the environment that satisfies the general specifications described in this manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration When mounting the GOT to the control panel tighten the mounting screws in the specified torque range 0 36 Nem to 0 48 Nem with a Phillips head screwdriver No 2 Undertightening can cause the GOT to drop short circuit or malfunction Overtightening can cause a drop short circuit or malfunction due to the damage of the screws or the GOT Remove the protective film of the GOT When the user continues using the GOT with the protective film the film may not be removed Operate and store the GOT in environments without direct sunlight high temperature dust humidity and vibrations When using th
16. ed compatibility with Mitsubishi FA devices 4 Easy replacement 5 LED backlight 2 PART NAMES AND SETTINGS The following shows the part names for GT2310 and GT2308 Example GT2310 1 2 JA mn f d dr 1 Col il TE pra m 17 16 15 14 Description Display screen Displays the utility and the user created screen For operating the touch switches in the utility and the user Touch Pane created screen Lit in blue Power is properly supplied Lit in orange Screen saving Blinks in orange blue Backlight failure Not lit Power is not supplied POWER LED Unit installation fitting Mounting fixtures for fixing the GOT to the control panel Installation switch Used for OS installations at the GOT startup Lit SD card mounted Blinking SC card accessed No lit SD card not mounted or SD card mounted removable SD card access LED SD card interface For installing a SD card With a switching function for accepting and stopping the access to the SD card When the cover is opened Access is prohibited When the cover is closed Access is allowed SD card cover For connecting a USB mouse connecting a USB keyboard USB interface Host data transfer and data storage connector type TYPE A USB interface Device i connecting a personal computer connector type Mini Hole for attaching a cable clamp for prev
17. enting USB cable Hole for attaching a from being pulled out cable clamp Recommended product RSG 130 VO made by KITAGAWA INDUSTRIES CO LTD Terminating resistor setting switch Inside cover For switching on and off of the terminating resistor for the RS 422 and RS 485 communication port Default Off Battery holder Houses the battery Power terminal Power input terminal LG terminal FG terminal For communicating with a controller or connecting a Ethernet interface personal computer connector type RJ 45 modular jack For communicating with a controller Connector type D sub RS 232 interface 9 pin male For communicating with a controller Connector type D sub 9 pin female 3 SPECIFICATIONS 3 1 General Specifications Item Specifications Operating ambient 0 to 55 C temperature Storage ambient temperature Operating ambient humidity Storage ambient humidity RS 422 485 interface 20 to 60 C 10 to 90 RH non condensing 10 to 90 RH non condensing Half Sweep amplitude count Compliant Under 5 to 8 4Hz 3 5mm 10 times with JIS B intermittent eachinX Vibration resistance 3502 and vibration 84t0150Hz 9 8m s2 Y and Z IEC directions 61131 2 Under 5 to 8 4Hz 1 75mm continuous z vibration 8 4to150Hz 4 9m s Compliant with JIS B 3502 and IEC 61131 2 147 m s2 15G 3 times each in X Y and Z directions Ope
18. es User s Manual Utility SH 081195ENG A 1D7MJ6 For detailed manuals refer to the PDF manuals stored in the DVD ROM or CD ROM for the drawing software used Relevant Manuals For relevant manuals refer to the Help or the PDF manuals stored in the DVD ROM or CD ROM for the drawing software used The latest manuals are also available from MITSUBISHI ELECTRIC FA Global Website http www MitsubishiElectric co jp fa 2013MITSUBISHI ELECTRIC CORPORATION Before using the GOT Connect the connector of the GOT to the connector of the battery GT11 50BAT sold separately Refer to the GOT2000 Series Users Manual Hardware for the connection instructions For details on the GOT specifications installing instructions wiring maintenance and inspection or checking procedure for the version and the compatible standard refer to the GOT2000 Series User s Manual Hardware Packing List The GOT product package includes the following Description Quantity GT23 Installation fitting GT23 General Description 1 FEATURES 1 Abundant standard equipment e Variety of connection with FA devices e SD card interface compatible with the SDHC card having a large capacity and allowing high speed communication e Connection with various peripheral devices with the USB host 2 Improved usability e Abundant troubleshooting e Easy and clear screen creation e PC like operation screen 3 Enhanc
19. he length shown below at both ends of the cable and expose the shield braided wire for grounding For grounding with cable clamps refer to Section 4 4 3 PLC side il 230 or less 40 40 230 or less 9 06 1 57 1 57 9 06 Unit mm inch 4 When connecting to PLC manufactured by other company microcomputer temperature controller inverter servo amplifier CNC MODBUS R RTU or MODBUS R TCP connection Produce the cable RS 232 cable RS 422 cable for connecting the GOT to a controller with reference to the GOT2000 Series Connection Manual Configure the system to meet the EMC Directive specifications for the connected device when connecting the GOT to a controller The following gives the instructions to ensure the machinery comply with the EMC Directive However the manufacturer of the machinery must finally determine how to make it comply with the EMC Directives if it is actually compliant with the EMC Directives a For RS 422 485 cable e Each signal wire excluding SG and FG should be made into a two power wires and connected then twisted e Make the SG wire more than two wires and connect b For RS 232 cable Use a twisted pair style for each signal wire except SG FG with SG Ry y SD D o a I 0 DIR yc xL DSR DSR y yaa y DIR sG L s6 e Attach the ferrite core to the cable in the position as illustrated below GOT side Ferr
20. ipts and others are also interrupted Since this interruption makes an impact to the system operation it might cause failure After checking the light off of SD card access LED remove the SD card CAUTION ifthe data storage mounted on the GOT is removed while the GOT is accessed the data storage and files are damaged To remove the data storage from the GOT check that the access to the data storage in SD card access LED the system signal and others is not performed When inserting a SD card into the GOT make sure to close the SD card cover Failure to do so causes the data not to be read or written When removing the SD card from the GOT make sure to support the SD card by hand as it may pop out Failure to do so may cause the SD card to drop from the GOT resulting in a failure or break When inserting a USB device into a USB interface of the GOT make sure to insert the device into the interface firmly Failure to do so may cause the USB device to drop from the GOT resulting in a failure or break Before removing the USB device from the GOT follow the procedure for removal on the utility screen of the GOT After the successful completion dialog is displayed remove the USB device by hand carefully Failure to do so may cause the USB device to drop from the GOT resulting in a failure or break DISPOSAL PRECAUTIONS CAUTION When disposing of this product treat it as industrial waste When disposing of batteries sepa
21. it or cable may keep the outputs on or off Some failures of a touch panel may cause malfunction of the input objects such as a touch switch An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction The GOT backlight failure disables the operation on the touch switch s When the GOT backlight has a failure the POWER LED blinks orange blue and the display section dims In such a case the input by the touch switch s is disabled The display section of the GOT is an analog resistive type touch panel If you touch the display section simultaneously in 2 points or more the switch that is located around the center of the touched point if any may operate Do not touch the display section in 2 points or more simultaneously Doing so may cause an accident due to incorrect output or malfunction When programs or parameters of the controller such as a PLC that is monitored by the GOT are changed be sure to reset the GOT or turn on the unit again after shutting off the power as soon as possible Not
22. ite Core PLC side ZCAT3035 1330 iil m M 100 or less a 100 or less 3 94 3 94 Unit mm inch 4 4 3 Grounding the cable Ground the cable and grounding wire to the control panel where the GOT and base unit are installed 1 Ground the braided shield portion of the cable to the control panel with the cable clamp AD75CK iT Braided shield U gt Cable clamps AT For the cable clamp attaching details elk refer to AD75CK type Cable Clamping Instruction Manual lt IB 68682 gt 2 Do not arrange the cable clamp adjacent to other cables which do not clamp Noise from the control panel may access the GOT from the cable clamp and cause adverse effects 5 INSTALLATION 5 1 Control Panel Inside Dimensions for Mounting GOT Install the GOT on the control panel out of the way for the equipment inside the control panel Do not install the GOT and the unit in prohibited areas for the installation Applicable cable Some cables may need to be longer than the specified dimensions when connecting to the GOT Therefore consider the connector dimensions and bending radius of the cable as well for installation 5 2 Panel Cutting Dimensions Panel thickness 1 6 to 4mm A 0 06 to 0 16 inch 289 11 38 200 7 87 2 0 08 2 0 08 0 0 0 0 m 227 8 94 176 6 93 2 0 08 2 0 08 0 0 0 0 Unit mm inch
23. ment is used In pollution degree 2 only non conductive pollution occurs but temporary conductivity may be produced due to condensation Refer to the GOT2000 Series User s Manual Hardware for details on the performance specifications of each GOT 3 2 Power Supply Specifications The following indicates the power supply specifications for GT23 Operation at momentary failure e Ifan instantaneous power failure occurs in the power supply and continues for more than the permissible period the GOT will be reset Make sure to power on the unit more than 5 seconds after power off 3 2 1 For GOTs powered from the 100 to 240VAC power supply Specifications GT2310 VTBA GT2308 VTBA AC100 to 240VAC 10 15 50 60Hz 5 44VA maximum load 30VA maximum load maximum load 18W or less 11W or less Power Stand alone 15W OW ption Stand alone with backlight off Power supply voltage Power frequency Input max apparent power 8W 6w 40A or less 4ms operating ambient temperature Inrush current 25 C maximum load Allowable momentary power failure ti 20 ms or less 100VAC or more ime 1 500Vp p noise voltage 14s noise width when measuring with a noise simulator under 25 to 60Hz noise frequency Noise immunity 1500VAC for 1 minute across power terminals and Dielectric withstand voltage earth 10M or more across power terminals and earth by a 500V DC insulatio
24. n resistance tester 0 75 mm2 to 2 mm Solderless terminal for M3 screw RAV1 25 3 V2 3 3 V2 N3A FV2 N3A Insulation resistance Applicable wire size Applicable solderless terminal Applicable tightening torque Terminal block terminal screw gt to 0 8 N m 3 2 2 For GOTs powered from the 24VDC power supply Specifications GT2310 VTBD GT2308 VTBD Power supply voltage DC24V 25 20 Maximum load 16W or less 11W or less Power Stand alone 13W 8W consu mption oo alone with backlight 7W eu 40A or less 2ms operating ambient temperature Inrush current 25 C maximum load Allowable momentary power failure 10 ms or less time 500Vp p noise voltage 14s noise width when measuring with a noise simulator under 25 to 60Hz noise frequency 350VAC for 1 minute across power terminals and earth 10M or more across power terminals and earth by a 500V DC insulation resistance tester 0 75 mm to 2 mm Solderless terminal for M3 screw RAV1 25 3 V2 3 3 V2 N3A FV2 N3A 0 5 Nem to 0 8 N m Noise immunity Dielectric withstand voltage Insulation resistance Applicable wire size Applicable solderless terminal Applicable tightening torque Terminal block terminal screw 3 3 External Dimensions GT2310 GT2308 D 303 11 93 o 241 9 49 lS 208 8 19 166 6 54 m T a T SH gl g eH
25. nd and ground them with the thickest and shortest wire possible The wire length must be 30cm 11 81in or shorter The LG and FG terminals function is to pass the noise generated in the PC system to the ground so an impedance that is as low as possible must be ensured As the wires are used to relieve the noise the wire itself carries a large noise content and thus short wiring means that the wire is prevented from acting as an antenna Note A long conductor will become a more efficient antenna at high frequency b The earth wire led from the earthing point must be twisted with the power supply wires By twisting with the earthing wire noise flowing from the power supply wires can be relieved to the earthing However if a filter is installed on the power supply wires the wires and the earthing wire may not need to be twisted 4 1 3 Noise filter power supply line filter The noise filter power supply line filter is a device effective to reduce conducted noise Except some models installation of a noise filter onto the power supply lines is not necessary However conducted noise can be reduced if it is installed The noise filter is generally effective for reducing conducted noise in the band of 10MHz or less Usage of the following filters is recommended Model name FN343 3 05 FN660 6 06 RSHN 2003 Manufacturer SCHAFFNER SCHAFFNER Rated current 3A 6A Rated voltage 250V The precautions required when in
26. not always match the above 4 1 1 EMC directive The standards of the EMC Directive are shown below Applied standard Standard value 30M 230MHz QP Electromagnetic 30dBu V m 30m in CISPR16 2 3 emissions from the measurement range 3 Radiated noise product are 230M 1000MHz QP measured 37dBu V m 30m in measurement range Test standard Test details 2 3 Electromagnetic 150k 500kHz QP 79dB CISPR16 2 1 emissions from the Mean 66dB Conducted noise product to the power 500k 30MHz QP 73dB line is measured Mean 60dB 2 Immunity test in IEC61000 4 2 which static Electrostatic electricity is applied immunity to the cabinet of the equipment 4kV Contact discharge 8kV Aerial discharge IEC61000 4 3 Immunity test in 80 1000MHz 10V m Radiated which field is 1 4 2GHz 3V m electromagnetic irradiated to the 2 0 2 7GHz 1V m field AM modulation product 80 AM modulation 1kHz Immunity test in Power line 2kV which burst noise is Digital I O 24V or higher 1kV applied to the power Digital I O 24V or less gt 250V line and signal lines Analog I O signal lines gt 250V IEC61000 4 4 Fast transient burst noise AC power type Power line between line and ground 2kV Power line between lines EN61131 2 1kV 2007 Immunity test in Data communication port IEC61000 4 5 which lightening 1kV Surge immunity surge is applied to DC power type the product Power line
27. oduct fails install appropriate backup or failsafe functions in the system Country Region Sales office Tel U S A Mitsubishi Electric Automation Inc 500 Corporate Woods Parkway Vernon Hills IL 60061 U S A Tel 1 847 478 2100 Brazil MELCO TEC Rep Com e Assessoria Tecnica Ltda Rua Correia Dias 184 Edificio Paraiso Trade Center 8 andar Paraiso Sao Paulo SP Brazil Tel 55 11 5908 8331 Germany Mitsubishi Electric Europe B V German Branch Gothaer Strasse 8 D 40880 Ratingen GERMANY Tel 49 2102 486 0 U K Mitsubishi Electric Europe B V UK Branch Travellers Lane Hatfield Hertfordshire AL10 8XB U K Tel 44 1707 276100 Italy Mitsubishi Electric Europe B V Italian Branch Centro Dir Colleoni Pal Perseo Ingr 2 Via Paracelso 12 I 20041 Agrate Brianza Milano Italy Tel 39 039 60531 Spain Mitsubishi Electric Europe B V Spanish Branch Carretera de Rubi 76 80 E 08190 Sant Cugat del Valles Barcelona Spain Tel 34 93 565 3131 France Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets F 92741 Nanterre Cedex France Tel 33 1 5568 5568 South Africa Circuit Breaker Industries Ltd Private Bag 2016 ZA 1600 Isando South Africa Tel 27 11 928 2000 Hong Kong Mitsubishi Electric Automation Hong Kong Ltd 10th Floor Manulife Tower 169 Electric Road North Point Hong Kong Tel 852 2887 8870 China Mitsubishi Electric Automation China Ltd 4 F Zhi Fu Plazz No 80 Xin Chang Road
28. ol panel is opened Dustproof and waterproof features The control panel also provides protection from dust water and other substances Insufficient ingression protection may lower the insulation withstand voltage resulting in insulation destruction The insulation in the GOT is designed to cope with the pollution level 2 so use in an environment with pollustion level 2 or better N Pollution level 1 An environment where the air is dry and conductive dust does not exist Pollution level 2 An environment where conductive dust does not usually exist but occasional temporary conductivity occurs due to the accumulated dust Generally this is the level for inside the control panel equivalent a control room or on the floor of a typical factory Pollution level 3 An environment where conductive dust exits and conductivity may be generated due to the accumulated dust An environment for a typical factory floor Pollution level 4 Continuous conductivity may occur due to rain snow etc An outdoor environment 4 2 4 Grounding The following are applicable ground terminals Use them in the grounded state Be sure to ground the GOT for ensuring the safety and complying with the EMC Directive Functional grounding L Improves the noise resistance 4 2 5 External wiring 1 External devices When a device with a hazardous voltage circuit is externally connected to the GOT select a model which complies with the Low Voltage
29. out notice Printed in Japan September 2013
30. plode or ignite resulting in injury and fire Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit CAUTION Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due toa cable connection fault When unplugging the cable connected to the unit do not hold and pull from the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault Do not drop the module or subject it to strong shock A module damage may result Do not drop or give an impact to the battery mounted to the unit Doing so may damage the battery causing the battery fluid to leak inside the battery If the battery is dropped or given an impact dispose of it without using Before touching the unit always touch grounded metals etc to discharge
31. rate them from other wastes according to the local regulations Refer to the GOT2000 Series User s Manual Hardware for details of the battery directive in the EU member states TRANSPORTATION PRECAUTIONS A CAUTION When transporting lithium batteries make sure to treat them based on the transport regulations Refer to the GOT2000 Series User s Manual Hardware for details of the regulated models Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation When fumigants that contain halogen materials such as fluorine chlorine bromine and iodine are used for disinfecting and protecting wooden packaging from insects they cause malfunction when entering our products Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products or treat packaging with methods other than fumigation heat method Additionally disinfect and protect wood from insects before packing products Vianuals The following shows manuals relevant to this product Detailed Manual Manual number Manual name Model code GOT2000 Series User s Manual Hardware SH 081194ENG A 1D7MJ5 GOT2000 Seri
32. rating No greasy fumes corrosive gas flammable gas excessive atmosphere conductive dust and direct sunlight Same as storage atmosphere Operating altitude 2000 m 6562 ft max Installation location Inside control panel Overvoltage category Pollution degree 4 2 or less Cooling method Self cooling Type D grounding 1009 or less Connect to panel if unable to ground Frequency Acceleration Shock resistance Il or less Grounding 1 If ambient temperature exceeds 40 c do not exceed absolute humidity 40 c 90 2 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude Om Oft Failure to observe this instruction may cause a malfunction When an air purge is made inside the control panel by adding pressure there may be a clearance between the surface sheet and the screen making it difficult to use the touch panel or the sheet may come off 3 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises Category II applies to equipment for which electrical power is supplied from fixed facilities The surge voltage withstand level for up to the rated voltage of 300 V is 2500 V 4 This index indicates the degree to which conductive material is generated in the environment where the equip
33. stalling a noise filter are described below 1 Do not install the input and output cables of the noise filter together to prevent the output side noise will be inducted into the input side cable where noise has been eliminated by the noise filer Input side Input side power supply side ipower sunni side Induction Filter Filter Output side Output side Las device side L device side e Installing the input and output cables e Separate the input cable from the output together will cause noise induction cable 2 Connect the noise filter s ground terminal to the control panel with the shortest cable as possible approx 10cm 3 94 in or less 4 2 Requirements for Compliance with the Low Voltage Directive The Low Voltage Directive requires each device which operates with power supply ranging from 50VAC to 1000V and 75VDC to 1500V to satisfy necessary safety items In the Sections from 4 2 1 to 4 2 5 cautions on installation and wiring of the GOT to conform to the Low Voltage Directive requires are described We have put the maximum effort to develop this material based on the requirements and standards of the Directive that we have collected However compatibility of the devices which are fabricated according to the contents of this manual to the above Directive is not guaranteed Each manufacturer who fabricates such device should make the final judgement about th
Download Pdf Manuals
Related Search