Home

IB940 USER`S MANUAL - IBT Technologies Inc.

1. e Intel Q965 Express Chipset Based Support LGA775 Intel Core 2 Duo Processors Support FSB 1066 800 533MHz Support up to 4GB DDRII 800 667 533 memory e 1 x Mini PCI Express Slot Support one 10 100 or two Gigabit LAN on board e 4x SATA II 1 x IDE 1x Floppy 6 x USB 2 0 2 x COM 1 x Parallel 5 1Ch Audio 1 x TMDS Dual channel LVDS support 18 24 bit ER EE mQalEi B 940 User s Manual 1 INTRODUCTION Checklist Your IB940 Core 2 Duo CPU Card package should include the items listed below The IB940 Card This User s manual 1 x IDE cable 1 x Floppy cable 1 x SATA cable 1 x TMDS cable 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket 1 Y Cable supporting a PS 2 Keyboard and a PS 2 Mouse Audio cable with bracket Audio 18K USB cable with bracket USB2K 4 1 CD containing the following e Chipset Drivers e Flash Memory Utility Optional SATA Power Cord PW34 B 940 User s Manual INTRODUCTION Eee Specifications Form Factor Full Size CPU Card PICMG1 0 Processor Support for Intel Core 2 Duo processor Conroe core in LGA775 socket FSB 533 800 1066 MHz Chipset Intel Broadwater Q965 Chipset consisting of e Intel Q965 Graphics Memory Controller Hub GMCH e Intel ICH8 ICH8DO UO Controller Hub BIOS e Award BIO
2. BIOS SETUP Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control CPU Clock Ratio Unlock Disabled ITEM HELP CPU Clock Ratio 8x Menu Level gt Auto Detect PCI Clk Disabled Spread Spectrum Disabled CPU Host SRC PCI Clock Default CPU Clock Ratio Unlock This field has a default setting of Disabled When enabled it allows the CPU clock ratio setting in the next field to be changed to a lower ratio Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock Spread Spectrum This field sets the value of the spread spectrum The default setting is Disabled This field is for CE testing use only CPU Host SRC PCI Clock This field has a default setting of Default B 940 User s Manual 43 BIOS SETUP BEEN Load Fail Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Load Optimized Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features Set Supervisor User Password These two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a passwo
3. Suspend Mode HDD Power Down Soft Off by PWR BTTN CPU THRM Throttling Wake Up by PCI card Power On by Ring Resume by Alarm Date of Month Alarm Time hh mm ss Alarm Reload Global Timer Events Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD COM LPT Port PCI PIRQ A D ACPI Function Power Management Setup Enabled ITEM HELP S3 STR User Define Menu Level gt V H SYNC Blank Yes Stop Grant 3 Disabled Disabled Instant Off 75 0 Disabled Disabled Disabled 0 0 0 0 Disabled Disabled Disabled Disabled Disabled Disabled Enable this function to support ACPI Advance Configuration and Power Interface ACPI Suspend The default setting of the ACPI Suspend mode is 3 STR Power Management This field allows you to select the type of power saving management modes There are four selections for Power Management Min Power Saving Max Power Saving User Define Minimum power management Maximum power management Each of the ranges is from 1 min to Ihr Except for HDD Power Down which ranges from 1 min to 15 min ss 38 B 940 User s Manual BIOS SETUP EE Video Off Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows BIOS to control the video display Blank Screen Writes blanks to the video buffer Video Off In
4. Watchdog Timer Configuration esses 55 D Digital VO Sample Code 59 B 940 User s Manual Wi Ee ATTENTION It is strongly recommended that only heatsinks that have corresponding metal backplates be used on the CPU card This is to avoid the CPU card being bent distorted causing the CPU card to become damaged A reference picture of a backplate and heatsink that has backplate are shown below B 940 User s Manual INTRODUCTION Introduction Product Description The IB940 CPU card is based on the Intel Q965 chipset and supports the Intel Core 2 Duo processor with 1066 800 533 MHz System Bus It supports the PCI Express x16 graphics interface for the latest high performance graphics cards The PCI Express x1 I O ports offer up to 3 5X the bandwidth over traditional PCI architecture delivering faster access to peripheral I O devices The Intel GMA 3000 graphics on board supports Dual Independent Display and delivers richer visual color and picture clarity without the need for additional discrete graphics cards and the integrated audio support enables premium digital sound and delivers advanced features such as multiple audio The CPU card also supports Dual Channel DDR2 memory in four DIMM sockets and delivers up to 12 8 GB s of bandwidth and 8 GB memory addressability for faster system responsiveness Dimensions of the board are 338mm x 126mm The main features of the CPU card are
5. 5 6 USBI Ground 7 8 ve ER EE EE dl B 940 User s Manual 21 INSTALLATIONS EE EE EE EE EE EE M J16 Intel 82562V 10 100 or Intel 82566DC GbE RJ 45 J16 is the 10 100 or Gigabit LAN RJ45 connector based on the Intel PCI Express 10 100 or GbE controller Note 10 100 LAN for 1B940 Gigabit LAN for IB940F J18 Wake On LAN Connector J18 is a 3 pin header for the Wake On LAN function on the CPU Card The following table shows the pin out assignments of this connector Wake On LAN will function properly only with an ATX power supply with 5VSB that has 1A Pin Signal Name 5VSB Ground LAN Wakeup J19 SPI Flash Connector factory use only J20 J21 LVDS Connectors 1st channel 2nd channel The LVDS connectors DF13 20 pin mating connectors are composed of the first channel J5 and second channel J10 to support 24 bit or 48 bit TX0 Tx ad 5va3av 8 Ee sa ENABKL Remarks Maximum current for 12V is 1A 22 B 940 User s Manual INSTALLATIONS J22 Panel Inverter Power Connector Pin Signal Name Remarks Maximum current is 1A J23 Intel PCI Express GbE RJ45 Connector J23 is the Gigabit LAN RJ45 connector based on the Intel PCI Express GbE controller IL Tl U46 x1 Mini PCI Express Slot B 940 User s Manual 23 INSTALLATIONS BEE This page is intentionally left blank BEES EE EE EE
6. entering a power saving mode or can awaken the system from such a mode When an I O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it interrupts itself and performs the service a EE EE EE EE EI 40 B 940 User s Manual BIOS SETUP EE PNP PCI Configurations This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Init Display First PCI Slot ITEM HELP Reset Configuration Data Disabled Menu Level Resources Controlled B Auto ESCD IRQ Resources Press Enter PCI VGA Palette Snoop Disabled INT Pin 1 Assignmen Au INT Pin 2 Assignmen Au INT Pin 3 Assignmen Au INT Pin 4 Assignmen Au INT Pin 5 Assignmen Au INT Pin 6 Assignmen Au INT Pin 7 Assignmen Au INT Pin 8 Assignmen Au e e o o o o o o PCI Express relative items Maximum Payload Size Init Display First The default setting is PCI Card Reset Configuration Data The default value is Disabled Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices with the use of a PnP operating system such as Windows 95 PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether or not MPEG I
7. you to connect external devices such as keyboard floppy disk drives hard disk drives printers etc The following table lists the connectors on IB940 and their respective functions Jumper Locations on IB940 ees se sees 13 CPU FANI CPU Fan Power Connector se se se se se ee ee ee ee 14 PWR FANI SYSTEM Fan Power Connectors se se se ee ee ee 14 VGA1 VGA CRT Connector esee enne 14 FDC1 Floppy Drive Connector eee 15 IDEI Primary IDE Connectors eene 15 S ATAI S ATA2 5 ATA3 S ATA4 SATA HDD Connectors 16 ATX1 12V 12V Power Connector ees sesse se se ee ee ee ee ER Re ee ee 16 J1 TMDS Panel Connector iese ese ee ee ee ee ee ee ee Re Re ee ee ee ee ee ee 16 J2 System Function Connector iese ees see eese 17 J3 Parallel Port Connector eise see ee ee ee Ee ee ee ee ee Re ee ee ee ee ee 19 JA JS COMI and COM 2 Serial Ports Connector esse esse ese se se ee 19 J6 Digital VO Connector 4 in 4 out 20 J7 Audio Connector for 5 1 channel 20 JS IrDA Connector OE NE 20 J9 External ATX Power Connector iese ss ese ee see se ee ee ee ee ee ee ee 20 J10 CD In Audio Connector ees esse se ee ee ee ee Re ee ee ee ee ee 21 J11 J12 External PS 2 Keyboard and Mouse Connector 21 J13 PS 2 Keyboard and Mouse Connector esses 21 J17 J15 J14 USBO USBI Connector eee 21 J16 Inte
8. EE EE EE 24 B 940 User s Manual BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board The topics covered in this chapter are as follows BIOS Introduction n aniline hind ey intone dane 26 oe EN UR MO ER IE TE HE 26 Standard CMOS Setup 28 Advanced BIOS Features se se se ee ee ee ee ee ee ee 31 Advanced Chipset Features 34 Integrated Peripherals eee metere 35 Power Management Setup 38 PNP PCI Configurations eese ener 41 PC Health Status enee rtt tenere it mese 42 Frequency Voltage Control 43 Load Fail Safe Defaults esee 44 Load Optimized Defaults esee 44 Set Supervisor User Password 44 Save amp Exit Setup iine bon a Rb ede tm e e Rede 44 Exit Without Saving ee se ese Ge ee Gee SA nennen enne 44 MEE EE EE EE EE EE EE EE EE EE n m x B 940 User s Manual 25 BIOS SETUP Cn EE EE ET BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel processors The BIOS provides critical low level support for a standard device such as disk drives serial ports and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The Award BIOS provides a Setup utility program for specifying the system confi
9. EM HELP SuperlO Device Press Enter USB Device Setting Press Enter Menu Level gt Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Enabled ITEM HELP IDE DMA transfer access Enabled IDE Primary Master PIO Auto Menu Level gt IDE Primary Slave PIO Auto IDE Primary Master UDMA Auto IDE Primary Slave UDMA Auto On Chip Secondary PCI IDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto LEGACY Mode Support Enabled Phoenix AwardBIOS CMOS Setup Utility SuperlO Device POWER ON Function BUTTON ONLY KB Power ON Password Enter Hot Key power ON Ctrl F1 Menu Level Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 UART Mode Select Normal Onboard Parallel Port 378 IRQ7 Parallel Port Mode SPP PWRON After PWR Fail Off Phoenix AwardBIOS CMOS Setup Utility USB Device Setting USB 1 0 Controller Enabled ITEM HELP USB 2 0 Controller Enabled Menu Level gt USB Keyboard Function Disabled USB Mouse Function Disabled USB Storage Function Enabled dox USB Mass Storage Device Boot Setting MEE i d B 940 User s Manual 35 BIOS SETUP BEE IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive IDE DMA Transfer Access This field b
10. HF LD unsigned char LD Unlock_W627HF outportb W627HF_INDEX_PORT W627HF REG LD outportb W627HF DATA PORT LD Lock W627HF void Set W627HF Rest unsigned char REG unsigned char DATA Unlock_W627HF outportb W627HF INDEX PORT REG outportb W627HF DATA PORT DATA Lock W627HF unsigned char Get W627HF Reg unsigned char REG unsigned char Result Unlock_W627HF outportb W627HF_INDEX_PORT REG Result inportb W627HF DATA PORT Lock W627HF return Result ER EE EE EE EE EE EE EE EE B 940 User s Manual 61 APPENDIX BEES File of the Main cpp THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE include lt dos h gt include lt conio h gt include lt stdio h gt include lt stdlib h gt include W627HF H void ClrKbBuf void int main void unsigned char GetDI unsigned char void SetDo unsigned char unsigned char int main void unsigned char ucDO 0 data for digital output unsigned char ucDI data for digital input unsigned char ucBuf char SIO SIO Init W627HF if SIO 0 printf Can not detect Winbond 83627HF 83627THF 83627EHF program abort n return 1 switch SIO E case 1 printf Winbond 83627HF is detected n break case 2 pri
11. IB940 LGA775 Core 2 Duo Intel Q965 Chipset Full Size CPU Card USER S MANUAL Version 1 0A Acknowledgments Award is a registered trademark of Award Software International Inc PS 2 is a trademark of International Business Machines Corporation Intel and Core 2 Duo are registered trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corporation Winbond is a registered trademark of Winbond Electronics Corporation All other product names or trademarks are properties of their respective owners A B 940 User s Manual Table of Contents Introduction 1 Product Descriptions sesse esse ses e a e eee 1 Bed dil RR m EE ER 2 eie leke RA EO EE HR EE N 3 Board DIMENSIONS sesse ese ee ee e AA ee ee ee A Installations ss 5 Installing the CPU 4 uit eria 6 Installing the Memor 7 Setting the Jumpers esse et ee Se GR rennen 8 Connectors on IB940 sss 12 BIOS Selup menaces ek 25 Drivers Installation 45 Intel Q965 Chipset Software Installation Utility 46 Intel Q965 Chipset Graphics Driver 48 Realtek Codec Audio Driver Installation 50 Intel LAN Drivers Installation 2 00 0 eeceeeeceenteeeeeeeees 51 Appendix EEN 53 A VO Port Address Map 53 B Interrupt Request Lines RO sesse ese ee ee ee 54 C
12. IXED memory Size SDVO Device Setting SDVO LVDS Protocol SDVO Panel Number Boot Display Enabled ITEM HELP Disabled Menu Level gt Press Enter Auto 8MB DVMT 128MB None 1 Ch SPWG 18bit 1024 x 768 Auto System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Memory Hole At 15M 16M In order to improve performance certain space in memory can be reserved for ISA cards This memory must be mapped into the memory space below 16 MB The choices are Enabled and Disabled On Chip VGA Setting The fields under the On Chip VGA Setting and their default settings are PEG On Chip VGA Control Auto On Chip Frame Buffer Size 8MB DVMT Mode DVMT DVMT Fixed Memory Size 128MB SDVO Device Setting The default setting is None and other options are LVDS LVDS DVI and DVI Boot Display The default setting is Auto and other options are CRT LVDS CRT LVDS DVI and CRT DVI MEE EE EE H gg EE EE EE 34 B 940 User s Manual BIOS SETUP SEE Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals The first screen shows three main items for user to select Once an item selected a submenu appears Details follow Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Device Press Enter IT
13. LLATIONS JBAT1 Clear CMOS Contents Use JBAT1 a 3 pin header to clear the CMOS contents Note that the ATX power connector should be disconnected from the CPU Card before clearing CMOS Pin 1 2 Short Closed Normal Pin 2 3 Short Closed Clear CMOS JP1 JP2 JP3 RS232 422 485 COM2 Selection COMI is fixed for RS 232 use only COM2 is selectable for RS232 RS 422 and RS 485 ID394 COM3 and COMA are fixed for RS 232 use only The following table describes the jumper settings for COM2 selection COM2 Function ee JP1 3 4 Jumper Setting JP2 pin closed 1 3 amp 2 4 JP3 1 3 amp 2 4 JP4 JP5 COM1 COM2 RS232 5V 12V Power Setting EE N Phe ee ao 7 1 2 Short Closed 12V Pin 3 4 Short Closed Pin 5 6 Short Closed 10 B 940 User s Manual INSTALLATIONS JP7 Processor Setting Pin 1 2 Shor Short Closed Celeron D Pin 1 2 Core 2 Duo TT Open Pentium D Pentium 4 HT JP8 LVDS Panel Power Select Setting Panel Voltage Pin 1 2 3 3V default Short Closed Pin 2 3 Short Closed J25 Power Supply Type Select Use J25 a 3 pin header to select between AT and ATX power supply l Pin 1 2 ATX 12d Short Closed Pin 2 3 AT c d Short Closed ER A EE EN B 940 User s Manual 11 INSTALLATIONS PS Connectors on IB940 The connectors on IB940 allows
14. Parallel Port These fields allow you to select the onboard serial and parallel ports and their addresses The default values for these ports are Serial Port 1 3F8 IRQ4 Serial Port 2 2F8 IRQ3 Parallel Port 378H IRQ7 UART Mode Select This field determines the UART 2 mode in your computer The default value is Normal Other options include IrDA and ASKIR Parallel Port Mode This field allows you to determine parallel port mode function SPP Standard Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port PWRON After PWR Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation USB 1 0 Controller The options for this field are Enabled and Disabled By default this field is set to Enabled USB 2 0 Controller The options for this field are Enabled and Disabled By default this field is set to Enabled In order to use USB 2 0 necessary OS drivers must be installed first Please update your system to Windows 2000 SP4 or Windows XP SP2 USB Keyboard Mouse Storage Function The options for this field are Enabled and Disabled By default this field is set to Disabled MEE EE EE EE EE EE EE uen id B 940 User s Manual 37 BIOS SETUP Power Management Setup Phoenix AwardBIOS CMOS Setup Utility ACPI Function ACPI Suspend Power Management Video Off Method Video Off In Suspend Suspend Type Modem Use IRQ
15. S footprint for both SPI amp LPC I F e Support for ACPI SMBIOS Memory 2x 240 pin DDRII 533 667 800 DIMM sockets supports single channel max 4 GB Video Intel Q965 integrated graphics subsystem GMA3000 DVI Chrontel CH7307C x1 for DVI LVDS Chrontel CH7308B x1 for 24 bit single dual channel LVDS LAN LAN1 dual footprint support option e Intel 82566DM Nineveh 10 100 1000 IB940F e Intel 82562V Ekron N 10 100 IB940 LAN2 Intel 82573L PCl e gigabit LAN IB940F Audio Intel ICH8 built in high definition audio w Realtek ALC888 Codec supports 5 1 CH audio line out line in amp mic LPC VO Winbond W83627EHG IrDA x1 Parallel x1 COM1 RS232 COM RS232 422 485 floppy Hardware monitor 3 thermal inputs 4 voltage monitor inputs amp 2 fan headers USB Intel ICH8 built in two High Speed USB host controller supports 6 USB 2 0 ports support for USB port disable w over current protection SATA II Intel ICH8 built in SATA II controller 3 0Gb sec w 4 ports IDE JMicron JM368 PCl e to PATA x1 for 1 PATA channel PCI to ISA ITE IT8888G x1 for high drive ISA bus bridge Expansion Mini PCl express socket x1 for Wireless LAN or other module Edge Connector e PS 2 connector x1 for PS 2 keyboard amp Mouse DB15 x1 for VGA RJ45 x2 for LAN 1 2 On Board e Standard SATA 7 pin shrouded vertical connector x4 Headers e 40 pins 0 1 pitch standard box header x1 for IDE Connectors e DF13 20 header x2 for LVDS e DF11 20 head
16. SA VESA VGA cards can work with PCI VGA When this field is enabled a PCI VGA can work with an MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with an MPEG ISA VESA card Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 128 EE EE EE EE EE EE EE EE EE IN B 940 User s Manual 41 BIOS SETUP DEENEN PC Health Status Phoenix AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature Disabled ITEM HELP CPU Warning Temperature Disabled System Temp 32 C 89 F CPU Temp 39 C 102 F Menu Level gt System Fan Speed 4000 RPM CPU Fan Speed 4000 RPM Vcore 1 24 V 12 V 12 03 V 18V 192 V 5 v 4 99 3 3V 3 15 VBAT V 3 13 5VSB V 5 29 CPU Warning Temperature This field allows the user to set the temperature so that when the temperature is reached the system sounds a warning This function can help prevent damage to the system that is caused by overheating Shutdown Temperature This field allows the user to set the temperature by which the system automatically shuts down once the threshold temperature is reached This function can help prevent damage to the system that is caused by overheating Temperatures Fan Speeds Voltages These fields are the parameters of the hardware monitoring function feature of the board The values are read only values as monitored by the system and show the PC health status a EE EE EE EE EE EE 42 B 940 User s Manual
17. Suspend When enabled the video is off in suspend mode Suspend Type The default setting for the Suspend Type field is Stop Grant Modem Use IRQ This field sets the IRQ used by the Modem By default the setting is 3 Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWRBTN This field defines the power off mode when using an ATX power supply The Instant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds CPU THRM Throttling When the system enters Doze mode the CPU clock runs only part of the time You may select the percent of time that the clock runs Wake Up by PCI card The default setting is Disabled Power On by Ring The default setting is Disabled BEE EE EE EE EE EE EE EE EE EE EI B 940 User s Manual 39 BIOS SETUP BEEN Resume by Alarm This field enables or disables the resumption of the system operation When enabled the user is allowed to set the Date and Time Reload Global Timer Events The HDD FDD COM LPT Ports and PCI PIRQ are I O events that can prevent the system from
18. Version Uninstall HDM Creating key HKLM SOFTWARE Microsoft Windows CurrentVersion Uninstall HDM Installing Driver Intel R Q965 Q963 Express Chipset Family Version 6 14 10 4785 Installation has completed Click Next to continue gt Next Intel R Installatian Framework 6 The Setup process is now complete Click Finish to restart the computer and for changes to take effect eC B 940 User s Manual 49 DRIVERS INSTALLATION Realtek Codec Audio Driver Installation 1 Insert the CD that comes with the board and the screen below would appear Click Intel R Q965 Chipset Drivers then Realtek High Definition Codec Audio Driver 2 When the Welcome screen appears click Next to continue Realtek High Definition Audio Driver Setup 2 19 Welcome to the InstallShield Wizard for Realtek High Definition Audio Driver install Realtek High Defi InstallShield 3 The Setup process is now complete Restart the computer when prompted for changes to take effect EE EE EE EE EE EE EE EE EE EE 50 B 940 User s Manual DRIVERS INSTALLATION Intel LAN Drivers Installation Follow the steps below to start installing the Intel PCI Express Gigabit LAN drivers 1 Insert the CD that comes with the board On the initial screen Click Intel R Q965 Chipset Drivers then Intel R PRO LAN Network Drivers 2 On the next screen click Install Drivers to start the drivers installation I
19. ard CMOS Features Date mm dd yy Fri Oct 20 2006 Item Help Time hh mm ss 16 11 00 Menu Level gt IDE Channel 0 Master None Change the day month IDE Channel 0 Slave None Year and century IDE Channel 1 Master None IDE Channel 1 Slave None IDE Channel 2 Master None IDE Channel 3 Master None IDE Channel 4 Master None IDE Channel 4 Slave None Drive A 1 44M 3 5 in Drive B None Video EGA VGA Halt On All But Keyboard Base Memory 640K Extended Memory 2086912K Total Memory 2087936K At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the F1 key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1 to 12 Date 1to31 Year 1999 to 2099 Bee EE EE EE G 28 B 940 User s Manual BIOS SETUP Ts EET To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time Time The time format is Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt or keys to set the current time IDE Channel Master Slave The onboard Seria
20. below from left to right on how to place the processor into the CPU socket Please note that the cover of the LGA775 socket must always be installed during transport to avoid damage to the socket NN AALIULLAALILLALLLLAALLLILLLLLLA ALLILLDZ OLLLLLLO LUVLUA L LHlclo 6 B 940 User s Manual INSTALLATIONS Installing the Memory The IB940 CPU Card supports four DDR2 memory sockets for a maximum total memory of 4GB in DDR memory type It supports DDR2 533 667 800 Basically the system memory interface has the following features Supports two 64 bit wide DDR data channels Available bandwidth up to 6 4GB s DDR2 800 for single channel mode Supports 256Mb 512Mb 1Gb DDR2 technologies Supports only x8 x16 DDR2 devices with four banks Supports only unbuffered DIMMs Supports opportunistic refresh Up to 32 simultaneously open pages four per row four rows maximum Installing and Removing Memory Modules To install the DDR2 modules locate the memory slot on the board and perform the following steps 1 Hold the DDR2 module so that the key of the DDR2 module align with those on the memory slot 2 Gently push the DDR2 module in an upright position until the clips of the slot close to hold the DDR2 module in place when the DDR module touches the bottom of the slot 3 To remove the DDR2 module press the clips with both hands DDR2 Modul
21. char Get W627EHF Reg unsigned char REG unsigned char Result Unlock_W627EHF outportb W627EHF INDEX PORT REG Result inportb W627EHF DATA PORT Lock W627EHFQ return Result THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE ifndef W627EHF H define __W627EHF_H 1 W627EHF_INDEX_PORT W627EHF_BASE W627EHF_DATA_PORT W627EHF_BASE 1 W627EHF_REG_LD 0x07 define W627EHF_UNLOCK define W627EHF_LOCK NE unsigned int Init_W627EHF void void Set_W627EHF_LD unsigned char void Set_W627EHF_Reg unsigned char unsigned char unsigned char Get_W627EHF_Reg unsigned char endif __W627EHF_H BEE EE EE EE al 58 B 940 User s Manual APPENDIX D Digital I O Sample Code Filename W627hf h THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE ifndef __W627HF_H define W627HF_H 1 ss define W627HF INDEX PORT W627HF BASE define W627HF DATA PORT W627HF_BASE 1 MEE define W627HF REG LD 0x07 define W627HF UNLOCK define W627HF LOCK NE unsigned int Init_W627HF void void Set_W627HF_LD unsigned char void Set_W627HF_Reg unsigne
22. d char unsigned char unsigned char Get_W627HF_Reg unsigned char endif __W627HF_H MEE EE EE EE EE EE EE EE EI B 940 User s Manual 59 APPENDIX DEE Filename W627hf cpp THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE A unsigned int W627HF BASE void Unlock W627HF void void Lock W627HF void unsigned int Init W627HF void unsigned int result ANA 1 627HF 2 627THF 4 627EHF A W627HF_BASE 0x2E W627HF_BASE 0x4E result Get_W627HF_Reg 0x20 if result 0x52 result 1 goto Init_Finish else if result 0x82 result 2 goto Init_Finish else if result 0x88 result 4 goto Init_Finish W627HF_BASE 0x4E W627HF_BASE 0x2E result Get_W627HF_Reg 0x20 if result 0x52 result 1 goto Init_Finish else if result 0x82 result 2 goto Init_Finish else if result 0x88 result 4 goto Init_Finish 60 B 940 User s Manual APPENDIX _ E EE Rr W627HF_BASE 0x00 result 0 Init_Finish return result void Unlock_W627HF void outportb W627HF_INDEX_PORT W627HF UNLOCK outportb W627HF INDEX PORT W627HF UNLOCK void Lock W627HF void outportb W627HF INDEX PORT W627HF LOCK void Set W627
23. ded that you exit al Windows programs before continuing Intel R Installation Framewor 48 B 940 User s Manual DRIVERS INSTALLATION 3 Click Yes to accept the software license agreement and proceed with the installation process 4 On Readme File Information screen click Next to continue Intel R Graphics Media Accelerator Driver a Fi P Readme File Information intel l n te Refer to the Readme file below to view the system requirements and installation information Press the Page Down key to view the rest of the file 3 Production Version Release le n Microsoft Windows 2000 Microsoft Windows XP Driver Revision Production Version 14 27 I Package 33119 I Graphics 6 14 10 4785 HDMI Audio 5 10 0 1026 Back Intel R Installation Framework 5 On Setup Progress screen click Next to continue the installation Intel R Graphics Media Accelerator Driver d intel Setup Progress Please wait while the following components are installed Copying file igxpun exe Copying file difxapi dll Copying file IScrNB bmp Copying file IScrNBR bmp Copying file HOMIENU dIl Creating key HKLMXSystem CurrentControlSet Control Windows SystemDirectorysC Creating key HKLM System CurrentControlSet Services ialm Devicel SystemDirec Creating key HKLM System CurrentControlSet Services ialm Devicel SystemDirec Creating key HKLM SOFTWARE Microsoft Windows Current
24. e Fixed as RS 232 1 2 J5 3 Configurable 4 as RS 232 5 RS 422 485 with jumpers T JP1 JP2 JP3 5 10 MEE EE EE EE EE EE EE EE EG B 940 User s Manual 19 INSTALLATIONS J6 Digital VO Connector 4 in 4 out This 10 pin digital VO connector supports TTL levels and is used to control external devices reguiring ON OFF circuitry SignalName Pin Pin LNENL 5 8 Ground MICI Ga MICI Dec J8 IrDA Connector J8 is used for an optional IrDA connector for wireless communication Pin Signal Name 1 5V 2 No connect 3 Ir RX 5 Ir TX J9 External ATX Power Connector Pin Signal Name Ground PS ON soft on off 5VSB Standby 45V C O 20 B 940 User s Manual INSTALLATIONS J10 CD In Audio Connector Pin Signal Name CD Audio R Ground Ground 4 CD Audio L J11 J12 External PS 2 Keyboard and Mouse Connector KB clock Mouse data KB data N C N C Ground Ground Vcc Vcc Mouse clock J13 PS 2 Keyboard and Mouse Connector J13 uses a Y cable with dual D connectors for a PS 2 keyboard and a PS 2 mouse Pin Signal Name 1 Keyboard data 2 Mouse data 3 Ground 4 5 Vcc Keyboard Clock 6 Mouse Clock J17 J15 J14 USBO USB1 Connector Signal Name Pin Pin Signal Name USBO
25. e Lock i Lock TE e ll m Lock Lock B 940 User s Manual 7 INSTALLATIONS Cee Se M Setting the Jumpers Jumpers are used on IB940 to select various settings and features according to your needs and applications Contact your supplier if you have doubts about the best configuration for your needs The following lists the connectors on IB940 and their respective functions Jumper Locations on B940 0 0 eee see see ke GR ee Ge Re Gee Re eke ee 9 JBATI Clear CMOS Contents seen 10 JP1 JP2 JP3 RS232 422 485 COMO Selection ee 10 JP4 JP5 COMI COM2 RS232 5V 12V Power Setting 10 JP Processor Setting L2 nnns eet ret e epe denotes 11 JP8 LVDS Panel Power Select 11 J25 Power Supply Type Select 11 RE EE EE 8 B 940 User s Manual INSTALLATIONS EE EE EE EE EE EE UE Jumper Locations on IB940 PTS N d B P d em N Es 2 5 mm S ee j og JP3 Jumpers RE nano S ee eR Page JBAT1 Clear CMOS Contents eese 10 JP1 JP2 JP3 RS232 422 485 COMO Selection sse 10 JP4 JP5 COMI COM2 RS232 5V 12V Power Setting 10 JP7 Processor Setting 11 JP8 LVDS Panel Power Select 11 J25 Power Supply Type Select 11 Er sic m KE B 940 User s Manual 9 INSTA
26. er x1 for DVI e 34 pins box header x1 for floppy e 26 pins box header x1 for printer e 5x2 pins box header x2 for COM1 2 e 4pins pin header x1 for CPU fan e 3 pins pin header x1 for system fan e 4X2 pins pin header x3 for USB1 6 RTC ICH8 built in RTC with on board lithium battery Watchdog Timer Yes 256 segments 0 1 2 255 sec min Digital lO 4 in and 4 out System Voltage 5V 3 3V 12V 12V amp 5VSB Board Size 338 x 122mm B 940 User s Manual INTRODUCTION Board Dimensions o 507 amp C 5 08 80 S x Dao vi voort 26 let mm ile var n l nmm HUTT E te Ei 388 17 TRL 338 25 CH 888 25 o 80 S BALL 6 9 sees 20 S9 20 06 VEOOL ee Lal ss 4 B 940 User s Manual INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB940 in order to set up a workable system The topics covered are Installing the CPU donee bte rte rete 6 Installing the Memor 7 Setting the Jumpers daa pee dolet pee 8 Connectors on IB940 ee ee ee ee ee ee Ge Se Ge RE 12 B 940 User s Manual 5 INSTALLATIONS Installing the CPU The IB940 CPU Card supports an LGA 775 processor socket for Intel Core 2 Duo processors The LGA 775 processor socket comes with a lever to secure the processor Refer to the pictures
27. field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up APIC Mode APIC stands for Advanced Programmable Interrupt Controller The default setting is Enabled MPS Version Control for OS This option is specifies the MPS Multiprocessor Specification version for the OS MPS version 1 4 added extended configuration tables to improve support for multiple PCI bus configurations and improve future expandability The default setting is 1 4 OS Select for DRAM 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends on certain BIOS calls to access memory The default setting is Non OS 2 Report No FDD for Win95 The default setting is Yes Small Logo EPA Show The EPA logo appears at the right side of the monitor screen when the system is boot up The default setting is Disabled B 940 User s Manual 33 BIOS SETUP BESSE Advanced Chipset Features This Setup menu controls the configuration of the chipset Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features System BIOS Cacheable Memory Hole at 15M 16M PCI Express Root Port Func VGA Setting PEG On Chip VGA Control On Chip Frame Buffer Size DVMT Mode DVMT F
28. gurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately activated Pressing the lt Del gt key immediately allows you to enter the Setup utility If you are a little bit late pressing the lt Del gt key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reser button or simultaneously pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items lt Enter gt to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and lt Esc gt to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices BEE EE EE EE EE EE EE 26 B 940 User s Manual BIOS SETUP Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exi
29. hat also becomes the identity of the device The following table lists the I O port addresses used Address 000h O1Fh 020h 03Fh 040h OSEh 060h 06Fh 070h 07Fh O80h 09Fh OAOh OBFh OCOh ODFh OFOh OFIh 1FOh 1F7h 278h 27Fh 2F8h 2FFh 2BOh 2DFh 378h 3FFh 360h 36Fh 3BOh 3BFh 3COh 3CFh EGA adapter 3D0h 3DFh 3FOh 3F7h 3F8h 3FFh B 940 User s Manual 53 APPENDIX B Interrupt Request Lines IRQ Peripheral devices use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on board BEE EE EE EE EE EE EE 54 B 940 User s Manual APPENDIX C Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count The WDT is suitable for use in the prevention of system lock up such as when software becomes trapped in a deadlock Under these sorts of circumstances the timer will count to zero and the selected outputs will be driven Under normal circumstance the user will restart the WDT at regular intervals before the timer counts to zero SAMPLE CODE THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE include lt stdio h gt include lt stdlib h gt include W627EHF H int ma
30. in int argc char argv void copyright void void Enable WDT int void Di ls int main int argc char argv bleWDT void unsigned char bBuf unsigned char bTime char endptr copyright if argc 2 printf Parameter incorrect n return 1 if Init W627EHF 0 printf Winbond 83627HF is not detected program abort n return 1 bTime strtol argv 1 endptr 10 EE EE EE EE EE EE EE EE EE EE ET B 940 User s Manual 55 APPENDIX EE EE EE 2 printf System will reset after d seconds n bTime EnableWDT bTime return 0 eessen void copyright void printf n Winbond 83627EHF Watch Timer Tester AUTO DETECT n Usage W627E WD reset time Ex W627E WD 3 gt reset system after 3 second n W627E WD 0 gt disable watch dog timer MEE void Enable WDT int interval unsigned char bBuf bBuf Get W627EHF Reg 0x2D bBuf amp 10x01 Set W627EHF Reg 0x2D bBuf Enable WDTO Set W627EHF LD 0x08 switch to logic device 8 Set W627EHF Reg 0x30 0x01 enable timer bBuf Get W627EHF Reg OxF5 bBuf amp 10x08 Set W627EHF Rest OxF5 bBuf count mode is second Set W627EHF Rest OxF6 interval set timer Set W627EHF LD 0x08 switch to logic device 8 Set W627EHF Reg OxF6 0x00 clear watchdog timer Set W627EHF Reg 0x30 0x00 watchdog disabled ss 56 B 940 User
31. ion Control for OS OS Select For DRAM gt 64MB Report No FDD for Win95 Small Logo EPA Show Disabled CPU Feature Press Enter to configure the settings relevant to CPU Feature Hard Disk Boot Priority With the field there is the option to choose aside from the hard disks connected Bootable add in Cards which refers to other external devices Virus Warning If this option is enabled an alarm message will be displayed when trying to write on the boot sector or on the partition table on the disk which is typical of the virus CPU L1 L2 L3 Cache Cache memory is additional memory that is much faster than conventional DRAM system memory CPUs from 486 type on up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These items allow you to enable speed up memory access or disable the cache function By default these items are Enabled B 940 User s Manual 31 BIOS SETUP BEEN Hyper Threading Technology Hyper Threading Technology enables two logical processors on a single physical processor by replicating partitioning and sharing the resources within the Intel NetBurst microarchitecture pipeline Quick Power On Self Test When enabled this field speeds up the Power On Self Test POST after the system is turned on If it i
32. is an ATX Power Supply On Off Switch on the system that connects to the power switch on the case When pressed the power switch will force the system to power on When pressed again it will force the system to power off Reset Switch Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again Orientation is not required when making a connection to this header Hard Disk Drive LED Connector Pins 10 and 20 This connector connects to the hard drive activity LED on control panel This LED will flash when the HDD is being accessed Pin Signal Name fi 10 HDD Active 18 B 940 User s Manual J3 Parallel Port Connector The following table describes the pin out assignments of this connector Signal Name Pin Een Signal Name J3 INSTALLATIONS Line printer strobe 1 AutoFeed PDO parallel data 0 2 Error PD1 parallel data 1 3 Initialize PD2 parallel data 2 4 Select PD3 parallel data 3 5 Ground PD4 parallel data 4 6 Ground PDS parallel data 5 7 Ground PD6 parallel data 6 8 21 Ground PD7 parallel data 7 9 22 Ground ACK acknowledge 10 23 Ground Busy 11 24 Ground Paper empty 12 25 Ground Select 13 N A N A J4 J5 COM1 and COM2 Serial Ports Connector J4 and J5 both 10 pin headers are the onboard serial port connectors 10 H DH HH M Pin 10 Nat Used JA Pin Signal Nam
33. l 82562V 10 100 or Intel 82566DC GbE RJ 45 22 Note 10 100 LAN for IB940 Gigabit LAN for IB940F 22 J18 Wake On LAN ConnecCtOr sesse ses se ee ee ee ee ER ee ee ee ee ee ee 22 J19 SPI Flash Connector factory use only 22 J20 J21 LVDS Connectors 1st channel 2nd channel 22 J22 Panel Inverter Power Connector iese ese ee ee se se ee ee ee ee ee ee 23 J23 Intel PCI Express GbE RJ45 Connector ee se se see see see se ee 23 U46 x1 Mini PCI Express Slot eee 23 ss 12 B 940 User s Manual INSTALLATIONS Jumper Locations on IB940 EN J3 e ju DDRII2 Bee 998399 pu FANI NS To EE E Ji ES BZ1 Se FANT CR Bai NT es ED DDRIH SES Jo oom J7 DS E 8 E Oi DI Ce E d amp E g E xa E s A vip CPU1 EM J12 kel 9 m Si Jn Lig JBATI Mae x J20 J21 x 8 j n e a JP6 88 c LEON CH J19 J18 J17 k JP8 j ax yf N gt BAT N Po 8 ON Mi el 13 B 940 User s Manual INSTALLATIONS DESEN The connectors on IB940 allows you to connect external devices such as keyboard floppy disk drives hard disk drives printers etc The following table lists the connectors on IB940 and their respective functions CPU_FAN1 CPU Fan Power Connector Pin Signal Name Control Sense 12V Ground PWR_FAN1 SYSTEM Fan Power Connectors E 12V 3 Reston gets VGA1 VGA CRT Connec
34. l ATA connectors provide Primary and Secondary channels for connecting up to four Serial ATA hard disks Each channel can support up to two hard disks the first is the Master and the second is the Slave Press lt Enter gt to configure the hard disk The selections include Auto Manual and None Select Manual to define the drive information manually You will be asked to enter the following items Capacity Capacity size of the hard disk drive Cylinder Number of cylinders Head Number of read write heads Precomp Write precompensation Landing Zone Landing zone Sector Number of sectors The Access Mode selections are as follows CHS HD lt 528MB LBA HD gt 528MB and supports Logical Block Addressing Large for MS DOS only Auto Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are 360KB 1 2MB 720KB 1 44MB 2 88MB 5 25in 525in 35in 35m 3 5 im p M c o EE EE EG B 940 User s Manual 29 BIOS SETUP BEEN Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA For EGA VGA SEGA SVGA or PGA monitor adapters default CGA 40 Power up in 40 column mode CGA 80 Power up in 80 column mode MONO For Hercules or MDA adapters Halt On This field determine
35. nents for the Intel R chipset that is on this system It is strongly recommended that you exit all Windows programs before continuing IntelFi Installation Frameworks 3 Click Yes to accept the software license agreement and proceed with the installation process 4 On the Readme Information screen click Next to continue the installation 5 The Setup process is now complete Click Finish to restart the computer and for changes to take effect Intel R Chipset Software Installation Utility 8 1 1 1009 The Intel R Chipset Software Installation Utility is complete You must restart your computer for changes to take effect Would you like to restart your computer now Yes want to restart my computer now C No will restart my computer later Remove any disks from their drives and then click Finish Intel R Installation Frameworks B 940 User s Manual 47 DRIVERS INSTALLATION Intel Q965 Chipset Graphics Driver Follow the instructions below to complete the installation under Windows 2000 XP 1 Insert the CD that comes with the board and the screen below would appear Click Intel R Q965 Chipset Drivers then Intel R Q965 Chipset Family Graphics Driver Intel Graphics Media Accelerator Driver Welcome to the setup for the Intel R Graphics Media Accelerator Driver This program will install the Intel R Graphics Media Accelerator Driver on this computer It is strongly recommen
36. nnector Pin Signal Name Ground ei ol Ground 12V 12V J1 TMDS Panel Connector TMDS stands Transition Minimized Differential Signaling Signal Name Pins Pin Signal Name L OHTPG 9 Has B A nnt l 16 B 940 User s Manual INSTALLATIONS J2 System Function Connector J2 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status J1 is a 20 pin header that provides interfaces for the following functions Hard Disk Drive LED Reset Switch Not Defined ATX Power On Switch SMI Hardware Switch Power LED Speaker Speaker Pins 1 4 This connector provides an interface to a speaker for audio tone generation An 8 ohm speaker is recommended Signal Name Cae Speaker out No connect Ground 5V Power LED Pins 11 15 The power LED indicates the status of the main power switch Pin Signal Name 11 Power LED 12 No connect m n Ground No connect Ground B 940 User s Manual 17 INSTALLATIONS DESEN SMI Hardware Switch Pins 6 and 16 This connector supports the Green Switch on the control panel which when pressed will force the system into the power saving mode immediately 1 Signal Name H SMI Ground ATX Power ON Switch Pins 7 and 17 This 2 pin connector
37. ntel R PRO Network Connections Intel PRO Network Connections Intel PRO 100 1000 and 10 GbE Connections Install Drivers Install SNMP Make Driver Disk View User Guides View Release Notes B 940 User s Manual 51 DRIVERS INSTALLATION EEE 3 When the Welcome screen appears click Next to continue 4 In the License Agreement screen click I accept the terms in license agreement and Next to accept the software license agreement and proceed with the installation process 5 When the Setup Type screen appears click Complete and Next to continue ie Intel R PRO Network Connections InstallShield Wizard Setup Type Choose the setup type that best suits your needs intel Please select a setup type Installs drivers Intel R PROSet for Windows Device Manager and Advanced Networking Services O Custom Choose which program Features you want installed and where they will be installed Recommended For advanced users 6 When the Ready to Install the Program screen appears click Install to continue 7 The Setup process is now complete InstallShield Wizard Completed Click Finish to restart the computer and for changes to take effect a EEEEEELLLLERIILLILLLIIIIIILLILILLLALLALLLALLALLLLIILALAALALOLILLILLLLLLOO LILAETAAao UoUoL L L p AVN 52 B 940 User s Manual APPENDIX Appendix A I O Port Address Map Each peripheral device in the system is assigned a set of I O port addresses t
38. ntf Winbond 83627THF is detected n break case 4 printf Winbond 83627EHF is detected n break Abu 0 3 input signal Abt 4 7 output signal ucDI GetDI 0x0F get current DI status SetDo ucDO OxF0 set current DO status return 0 unsigned char GetDI unsigned char Mask BEE EE EE EE EE EE EE EE EE 62 B 940 User s Manual APPENDIX S gt gt gt E E S SE ESS S LLLILLLLLIILILA LAnnZZ unsigned char result Set W627HF LD 0x07 switch to logic device 7 Set W627HF Reg 0xFO0 Mask set the DIO direction result Get W627HF Reg 0xF1 amp Mask return result JR void SetDo unsigned char NewData unsigned char Mask Set_W627HF_LD 0x07 switch to logic device 7 Set_W627HF_Reg 0xFO0 Mask set the DIO direction Set_W627HF_Reg 0xF1 NewData amp Mask EE void ClrKbBuf void while kbhit getchO EE B 940 User s Manual 63 APPENDIX HEER EE ET This page is intentionally left blank BEE EE EE EE EE EE EI 64 B 940 User s Manual
39. rd highlight the type you want and press lt Enter gt The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the lt Enter gt key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely Save amp Exit Setup This option allows you to determine whether or not to accept the modifications If you type Y you will quit the setup utility and save all changes into the CMOS memory If you type N you will return to Setup utility Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing Y will quit the Setup utility without saving the modifications Typing N will return you to Setup utility BEE EE OA EE EE EE 44 B 940 User s Manual DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 2000 and Windows XP The software and drivers are included with the board If you find the items missing please contact the vendor where you made the purchase The contents of this section include the follo
40. s Manual APPENDIX THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE include W627EHF H include lt dos h gt unsigned int W627EHF_BASE void Unlock_W627EHF void void Lock_W627EHF void unsigned int Init_W627EHF void unsigned int result unsigned char ucDid W627EHF_BASE 0x2E result W627EHF_BASE ucDid Get_W627EHF_Reg 0x20 if ucDid 0x88 goto Int Finish W627EHF_BASE 0x4E result W627EHF_BASE ucDid Get_W627EHF_Reg 0x20 if ucDid 0x88 goto Int Finish W627EHF_BASE 0x00 result W627EHF_BASE Init_Finish return result ls void Unlock_W627EHF void outportb W627EHF_INDEX_PORT W627EHF UNLOCK outportb W627EHF INDEX PORT W627EHF UNLOCK oid Lock W627EHF void outportb W627EHF INDEX PORT W627EHF LOCK void Set W627EHF LD unsigned char LD Unlock_W627EHF outportb W627EHF_INDEX_PORT W627EHF_REG_LD outportb W627EHF_DATA_PORT LD EE EE d EE EE EE EE EE B 940 User s Manual 57 APPENDIX DESEN Lock W627EHF void Set W627EHF Reg unsigned char REG unsigned char DATA Unlock_W627EHF outportb W627EHF INDEX PORT REG outportb W627EHF DATA PORT DATA Lock W627EHFQ unsigned
41. s set to Enabled BIOS will skip some items First Second Third Boot Device These fields determine the drive that the system searches first for an operating system The options available include LS 20 Hard Disk CDROM ZIP100 USB FDD USB ZIP USB CDROM and Disabled Boot Other Device These fields allow the system to search for an OS from other devices other than the ones selected in the First Second Third Boot Device Swap Floppy Drive The default setting is Disabled Boot up Floppy Seek The default setting is Disabled Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system Gate A20 Option This field allows you to select how Gate A20 is worked Gate A20 is a device used to address memory above 1 MB Typematic Rate Setting When disabled continually holding down a key on your keyboard will generate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds Settings are from 6 to 30 characters per second BEE EE EE EE 32 B 940 User s Manual BIOS SETUP SE Typematic Delay Msec When the typematic rate is enabled this item allows you to set the time interval for displaying the first and second characters By default this item is set to 250msec Security Option This
42. s whether or not the system will halt if an error is detected during power up No errors The system boot will not be halted for any error that may be detected All errors Whenever the BIOS detects a non fatal error the system will stop and you will be prompted All But Keyboard The system boot will not be halted for a keyboard error it will stop for all other errors All But Diskette The system boot will not be halted for a disk error it will stop for all other errors All But Disk Key The system boot will not be halted for a key board or disk error it will stop for all others I EE EE EE l 30 B 940 User s Manual BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature Hard Disk Boot Priority Virus Warning CPU L1 and L2 Cache CPU L3 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Drive Boot up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Typematic Rate Chars Sec Typematic Delay Msec Security Option APIC Mode Press Enter ITEM HELP Press Enter Disabled Menu Level gt Enabled Enabled Enabled Floppy Hard Disk CDROM Enabled Disabled Disabled On Fast Disabled 6 250 Setup Enabled MPS Vers
43. t Without Saving ESC Quit V 2 Select Item F10 Save amp Exit Setup Time Date Hard Disk Type The section below the setup items of the Main Menu displays the control keys for this menu At the bottom of the Main Menu just below the control keys section there is another section which displays information on the currently highlighted item in the list Note If the system cannot boot after making and saving system changes with Setup the Award BIOS supports an override to the CMOS settings that resets your system to its default Warning It is strongly recommended that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability Changing the defaults could cause the system to become unstable and crash in some cases B 940 User s Manual 27 BIOS SETUP DEENEN Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the motherboard is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged Phoenix AwardBIOS CMOS Setup Utility Stand
44. tor VGAI is a DB 15 VGA connector located beside the COMI port The following table shows the pin out assignments of this connector Signal Name Pins Pin Signal Name Red 1 2 Geen Re eNb J EECH D pope Hna EE EE r 14 B 940 User s Manual INSTALLATIONS FDC1 Floppy Drive Connector Signal Name Pin IDE1 Grund 9 21 Ground Pin Signal Name 6 Noconec 8 Imdex 22 Write data Track 00 Ground 29 IDE1 Primary IDE Connectors Signal Name Pin Pin Signal Name Reset IDE 30 Readdata Side 1 select Diskette change Ground Host data 7 Host data 8 Host data 6 Host data 9 Host data 5 Host data 10 Host data 4 Host data 11 Host data 3 Host data 12 Host data 2 Host data 13 Host data 1 Host data 14 Host data 0 Host data 15 Ground Protect pin DRQO Ground Host IOW Ground Host IOR Ground IOCHRDY Host ALE DACKO Ground IRQ14 No connect Address 1 No connect Address 0 Address 2 Chip select 0 Chip select 1 Activit B 940 User s Manual Ground 15 INSTALLATIONS S ATA1 S ATA2 S ATA3 S ATA4 SATA HDD Connectors Pin amp Signal Name eer EE ees ATX1 12V 12V Power Co
45. wing Intel Q965 Chipset Software Installation Utility 46 Intel Q965 Chipset Graphics Driver 48 Realtek Codec Audio Driver Installation 50 Intel LAN Drivers Installation eee 5 IMPORTANT NOTE After installing your Windows operating system Windows 2000 XP you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation ER EE EE EE H omddid B 940 User s Manual 45 DRIVERS INSTALLATION Intel Q965 Chipset Software Installation Utility The Intel Q965 Chipset Drivers should be installed first before the software drivers to enable Plug amp Play INF support for Intel chipset components Follow the instructions below to complete the installation under Windows 2000 XP Before installed Intel Chipset Software Installation Utility Please update your system to Windows 2000 SP4 or Windows XP SP1A 1 Insert the CD that comes with the board and the screen below would appear Click Intel R Q965 Chipset Drivers then Intel R Chipset Software Installation Utility 46 B 940 User s Manual DRIVERS INSTALLATION 2 When the Welcome screen appears click Next to continue Intel R Chipset Software Installation Utility 8 1 1 1009 Welcome to the Intel R Chipset Software Installation Utility This program will install the Plug and Play compo
46. y default is enabled OnChip Secondary PCI IDE This field by default is enabled IDE Primary Secondary Master Slave PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with the controller and CPU directly The system supports five modes numbered from 0 default to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode IDE Primary Secondary Master Slave UDMA These fields allow your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled LEGACY Mode Support When the Serial ATA SATA is set with the legacy mode enabled then the SATA is set to the conventional IDE mode Legacy mode is otherwise known as compatible mode Power ON Function This field is related to how the system is powered on such as with the use of conventional power button keyboard or hot keys The default is BUTTON ONLY KB Power ON Password This field allows users to set the password when keyboard power on is the mode of the Power ON function Hot Key Power ON This field sets certain keys also known as hot keys on the keyboard that can be used as a switch to power on the system Bi EE EE EE EE EE EE EI 36 B 940 User s Manual BIOS SETUP SE Onboard Serial

IB940 USER`S MANUAL - IBT Technologies Inc.

Contents

Download Pdf Manuals

Related Search

Related Contents