1432 Kb Manual_LS40
Contents
1. LIGHTING PROFESSIONAL MOVING HEAD USER MANUAL CLASSE LE HO KEEP THIS MANUAL FOR FUTURE NEEDS CE Thank you for your patronage We are confident that our excellent products and service can satisfy you For your own safety please read this user manual carefully before installing the device In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly CAUTION Keep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION Thank you for having chosen this professional LED moving head You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find 1 One XLR connection cable 2 One omega clamps 3 One safety rope 4 Manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features LED type SST 50 Extremely Long Life 100 000 hr and lower power consumption 3 DMX channel mode 10 12 14 channels 3 operational modes DMX 512 Master Slave amp Sound Active e 630 0r540 pan 270 tilt 8 bit Strobe ef2. lt E lt A gt SS ee WE Z CA S SEES Ze SZ LoS N V a A A EROS Mounting points Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury 7 Classe LS 40 v1 0 DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal ey f j le SA 120 Ohms nl lt DMX512 DMX controller Address 25 Address 13 Address 1 DMX 512 connection with DMX terminator For installations where the DMX cabl
3. after the user enter this manual if select Auto Program CH 22 means in this User s mode the Dimmer is in Channel 16 User mode With this function you can create user defined channel orders Preset User mode With this function you can adjust the rest user defined channel order Edit program Select program With this function you can select the program for the Program Run Edit program With this function you can edit the internal programs Edit scenes With this function you can edit the scenes of the internal programs Auto scenes rec The moving head features an integrated DMX recorder by which you can transmit the programmed scenes from your DMX controller to the moving head Adjust the desired scene numbers via the encoder from to When you call up the scenes at your controller they will automatically be transmitted to the moving head Excursion A Master unit can send up to 3 different data groups to the Slave units i e a Master unit can start 3 different Slave units which run 3 different programs The Master unit sends the 3 program parts in a continuous loop Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned to If e g a Slave unit is set to Slave 1 in the menu Set to Slave the Mas
4. desired program under Select program You can set the number of steps under Edit program You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time Music control With this function you can run the internal program sound controlled Information Time information Current Time With this function you can display the temporary running time of the device from the last power on The display shows XXXX XXXX stands for the number of hours The counter is resetted after turning the device off Total life Hours With this function you can display the running time of the device The display shows UXXXX XXXX stands for the number of hours Temp Info Head Temp With this function you can display the temperature on the display board of the base near CM Y filter in Celsius Software version With this function you can display the software version of the device Select Software version by turning the encoder Press the encoder the display shows V X X X X stands for the version number e g V 1 0 V 2 6 Turn the encoder in order to read the version of every individual IC Press the Mode Esc button in order to return to the main menu ll Classe LS 40 v1 0 PERSONALITY Status Settings Address via DMX With this function you can adjust the desired DMX address via an external controller Se
5. of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the move head which is a 12 channel fixture you should set the starting address of the first unit to 1 the second unit to 13 12 1 the third to 25 12 13 and so on Control Board The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Mode esc button until the display starts flashing Browse through the menu by pressing the Up button or Down button Press the Enter button in order to select the desired menu You can change the selection by pressing the Up button or Down button Confirm every selection by pressing the Enter button You can leave every mode by pressing the Mode esc button The functions provided are described in the following sections To access the display menu via the internal battery press the UP or DOWN button The display will automatically switch off about 10 seconds after the last actuation of the buttons Set Dmx Address A001 AXXX DMX address setting 3 2 Value Display PAN DMX value display s Set To Slave Slavel Slave2 Slave3 Slave setting L Auto Program Master Alone Auto program Music Control Master Alone Music control Time Information Current Time XXXX Hours Power on running time Total Life Hours
6. select the desired microphone sensitivity from 0 to 99 Hibernation Standby mode The lamp and step motors will be power off if the fixture stay without DMX signal for 15 mins Factory default And the fixture will be reset before working once it receive DMX signal again 1 Tap lt MODE ESC gt button access the main menu Tap the lt Up Down gt button until Personality is displayed Press ENTER the display will show Personality Tap the lt Up Down gt button until the display will show Status setting Press ENTER the display will show Status setting 2 Press lt Up Down gt the display will show Hibernation 3 Press lt ENTER the display will show Hibernation 4 The display show 15M Press lt Up Down gt the display will show 01M 02M 12 Classe LS 40 v1 0 99M or OFF 5 Press lt ENTER gt to confirm or press lt MODE ESC gt to return to the main menu Fans Control With this function you can set the speed of the running fans The selections have Auto high and low Display Setting Shut off time With this function you can shut off the LCD display after 2 to 59 minutes Turn the encoder in order to select the desired shut off time Locked keys the display With this function you can activate the automatic keylock function If this function is activated the keys will be locked automatically after exiting the edit mode for 15 seconds ke
7. the excessive lube splashes during the gobo rotating 4 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply AC 100V 240V 50Hz 60Hz Power consumption 90W Packing dimensions 41 x 31 5 x 53cm Net weight 9 2KGS Gross weight 11 7 KGS Remark errors and omissions for every information given in this manual excepted All information is subject to change without prior notice 20 Classe LS 40 v1 0
8. SE DMX channel s functions and their values 14 DMX channels Mode Channel Value Function St Ba Ex Color Wheel 0 14 Open white 15 29 Colorl 30 44 Color2 45 59 Color3 60 74 Color4 I 1 1 75 89 Color5 90 104 Color6 105 119 Color7 120 127 Color8 128 189 Forwards rainbow effect from fast to slow 190 193 No rotation 194 255 Backwards rainbow effect from slow to fast gt Color Wheel Fine 0 255 Color Wheel colour change to any position Fine Rotating gobos cont rotation 0 9 Open 10 19 Rot gobo 1 20 29 Rot gobo 2 2 2 3 30 39 Rot gobo 3 40 49 Rot gobo 4 50 59 Rot gobo 5 60 69 Rot gobo 6 70 79 Rot gobo 7 16 Classe LS 40 v1 0 80 95 Rot gobo 1 shake 96 111 Rot gobo2 shake 112 127 Rot gobo3 shake 128 143 Rot gobo4 shake 144 159 Rot gobo 5 shake 160 175 Rot gobo6 shake 176 191 Rot gobo7 shake 192 255 Rot gobo wheel cont rotation slow to fast Rotating gobo index rotating gobo rotation 0 127 Gobo indexing 128 189 Forwards gobo rotation from fast to slow 190 193 No rotation 194 255 Backwards gobo rotation from slow to fast Rotating gobo indexing Fine 0 255 Fine indexing Speed pan tilt movement 0 225 max to min speed 226 235 blackout by movement 236 245 blackout by all wheel changing 246 255 no fu
9. Strobe error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The TILT movement is not located in the default position after the reset 19 Classe LS 40 v1 0 CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 To make sure the smooth gobo rotation we suggest adding proper lube to the wheel each three month avoiding
10. XXXX Hours Fixture running time B Temperature Info Head Temperature XXX C F Temperature in the head E Software Version Ver1 0 Software version of each IC Status Settings Address via DMX ON OFF Add via DMX No DMX Status Close Hold Auto Music Auto run if no DMX Pan Reverse ON OFF Pan Reverse movement gt Tilt Reverse ON OFF Tilt Reverse movement E Pan Degree 630 540 Pan Degree Select z Feedback ON OFF Movement Feedback En Movement Speed Speed 1 4 switch Mic Sensitivity 0 99 Movement Mode Select Hibernation OFF 1 99M 15M Sensitivity of Mic Stand by mode Classe LS 40 v1 0 Fans Control Auto Fans Speed High Fans Speed Low Fans Speed Fans Speed Mode Select Display Setting Shutoff Time 02 59m OFF 05m Display shutoff time Key Lock ON OFF Key Lock Temperature C F Celsius Temperature switch Fahrenheit between C F Initial Effect PAN PAN XXX Initial effect position Reset Default ON OFF Restore factory set s Reset All Reset all motors S Reset Pan amp Tilt Reset Pan Tilt E Reset Colors Reset color wheel 9 Reset Gobos Reset gobos C Reset Others Reset other motors Test Channel PAN Test function Z Manual Control PAN PAN XXX Fine adjustment of the lamp 9 Calibrate Values Password Password XXX Calbrate and adjust the ii Color wheel Color wheel XXX effects to standard right position Password 050 U
11. agnet missing or the stepping motor is defective or its driving IC on the main PCB The color wheel is not located in the default position after the reset Gobo Rot Er Gobo Rot error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The Gobo Rot 1 is not located in the default position after the reset PAN movement Er PAN yoke movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunction sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The PAN movement is not located in the default position after the reset TILT movement Er TILT head movement error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The TILT movement is not located in the default position after the reset Prism Er Prism error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The TILT movement is not located in the default position after the reset Strobe Er
12. e device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury 4 Classe LS 40 v1 0 CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug Installation via the Omega holders 2 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener a Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the 13 hole in the middle of the bracket b Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise c Install the second Omega holder d Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw Notice this step is quite important to ensure that the fixture will not drop out by the damage of the clamp 5 Classe LS 40 v1 0 Dimensional Drawings 6 Classe LS 40 v1 0 Layout Drawings RS NE ERR Nee SEE d VA AXA XAA XAXA XA ea a ae a ee ek TET N ZZ AA SAn a gt ZS w ASSI PN NS
13. e has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1209 2 3 1 PIN 3 PIN 2 8 Classe LS 40 v1 0 Projector DMX start address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels
14. eping press the Mode Esc key for 3seconds if you want to deactivate the keylock status 1 Tap the UP button until LOCK is displayed and tap the ENTER button 2 Press the UP button to select ON to activate this function or OFF to deactivate this function Press ENTER to confirm 3 Press Mode Esc to return to the main menu Temperature C F With this function Display the temperature for Celsius or Fahrenheit Initial effect With this function Display initial effect position Reset Default With this function you can select restore factory set for ON or OFF the default is OFF Reset functions With this function you can reset the device via the Control Board You can select the different reset functions by turning the encoder Effect Adjust Test function of each channel With this function you can test each channel on its correct function Lamp adjustment With this function you can adjust the lamp more easily All effects will be canceled the shutter opens and the dimmer intensity will be set to 100 96 With the individual functions you can focus the light on a flat surface wall and erform the fine lamp adjustment Calibrate values With this function you can calibrate and adjust the effect wheels to their correct positions The password of calibrate values is 050 13 Classe LS 40 v1 0 Users Mode Set In this menu user can select different channels list by different sequence For example
15. fect with 1 13 flashes per second and pulse effect Color wheels 8dichroic filters plus open rainbow effect with adjustable speed in both directions Rotation gobo 7 interchangeable rotating gobos plus open Prism and prism rotating with 16 prism macros Linear dimmer in precise speed from 096 100 Friendly blue LCD display Rechargeable Back up Battrty for Display Preset program 7 built in programs can be called up via DMX controller Fan automatically adjust speed according to the LED temperature Software upload by optional accessory via DMX line l Classe LS 40 v1 0 Overview 1 Lens 2 Display 3 Mode Esc button Up button Down button Enter button Microphone Power supply O 00 N QN Aa Ff Fuse 10 Power switch 11 DMX out 12 DMX in 8 9 1041142 SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important f Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems 2 Classe LS 40 v1 0 If the device has been ex
16. ifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc the device was designed for indoor use only This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device A void brute force when installing or operating the device While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust Please don t project the beam onto combustible substances The minimum 3 Classe LS 40 v1 0 distance between light output from the projector and the illuminated surface must be more than 0 5 meter If you use the quick lock cam in hanging up the fixture please make sure the quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on
17. lect Address via DMX by turning the encoder Press the encoder the display shows ON or OFF Turn the encoder to select ON if you wish to enable this function or OFF if you don t Press the encoder to confirm Press the Mode Esc button in order to return to the main menu On the controller set the DM X value of channel 1 to 7 e Set the DM X value of channel 2 to 7 or 8 When set to 7 you can adjust the starting address between 1 and 255 When set to 8 you can adjust the starting address between 256 and 511 e Set the DM X value of channel 3 to the desired starting address If you want to set the starting address to 57 set channel 1 to 7 channel 2 to 7 and channel 3 to 57 If you want to set the starting address to 420 set channel 1 to 7 channel 2 to 8 and channel 3 to 164 256 164 420 Wait for approx 20 seconds and the unit will carry out a reset After that the new starting address is set No DMX Status With this function when the drive is not DMX signal it runs automatism close hold and music the default is hold Pan Reverse With this function you can reverse the Pan movement Tilt Reverse With this function you can reverse the Tilt movement Feedback With this function you can feedback switch of pan movement or tilt movement Movement Speed With this function you can select scan mode from 1 to 4 Mic Sensitivity With this function the default is 70 you can
18. nction PAN Movement 8bit 0 255 Pan Movement By 540 630 TILT Movement 8bit 0 255 Tilt Movement By 270 3 facet rotating prism Prism Gobo macros 0 31 open 32 63 3 facet prism 64 95 5 facet prism 96 127 trapezoid prism 128 135 Macro 1 136 143 Macro 2 144 151 Macro 3 152 159 Macro 4 160 167 Macro 5 168 175 Macro 6 176 183 Macro 7 184 191 Macro 8 192 199 Macro 9 200 207 Macro 10 208 215 Macro 11 216 223 Macro 12 224 231 Macro 13 232 239 Macro 14 Po e as Classe LS 40 v1 0 240 247 Macro 15 248 255 Macro 16 Shutter strobe 0 31 Led trun off 32 63 Led turn on 64 05 Strobe effect slow to fast 8 8 10 96 127 Led turn on 128 159 Pulse effect in sequences 160 191 Led turn on 192 223 Random strobe effect slow to fast 224 255 Led turn on 9 9 T Dimmer intensity 0 255 Intensity 0 to 100 Reset internal programs 0 19 Color amp Gobo change normal 20 29 Color change to any position 30 39 Color amp Gobo change to any position 40 59 No function 60 79 No function 80 84 All motor reset 85 87 Scan motor reset 88 90 Colors motor reset 91 93 Gobo motor reset MERE E 94 96 No function 97 99 Othe
19. posed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual mod
20. r motor reset 100 119 Internal program 1 120 139 Internal program 2 140 159 Internal program 3 160 179 Internal program 4 180 199 Internal program 5 200 219 Internal program 6 220 239 Internal program 7 240 255 Auto program by music T 13 Pan Fine 16bit 0 255 Fine control of Pan movement D 14 Tilt Fine 16bit 0 255 Fine control of Tilt movement 18 Classe LS 40 v1 0 ERROR MESSAGE When you turn on the fixture it will make a reset at first The display may show Err channel is XX while there are problems with one or more channels XX stands for channel 1 2 3 etc who has the testing sensor for positioning For example when the display shows Err channel is Color color it means there is some error in channel 1 If there are some errors on channel 1 channel 5 channel 6 at the same time you may see the error message Err channel is Color wheel Err channel is Pan movement Err channel is Tilt movement flash repeated for 2 times and then the fixture will generate a second reset If the fixture remain error message after performing reset more than 2 times only the channels which have errors can not work properly others can work as usual Please contact with dealer or manufacturer for service self repair is not allowed Color wheel Er Color wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunction sensor failed or m
21. same program as the master units Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 4 Program selection for Edit Program Select Edit program by turning the encoder Press the Enter button to confirm Select Edit program by turning the encoder Press the Enter button to confirm Turn the encoder to select the desired program With this function you can edit specific scenes into a specific program Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 5 Automatic Scene Recording Select Edit program by turning the encoder Press the Enter button to confirm Select Edit scenes by turning the encoder Turn the encoder to select the desired scene numbers You can program a maximum number of 250 Turn the encoder to select the desired scene numbers You can program a maximum number of 250 scenes Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu Example Program 2 includes scenes 10 11 12 13 Program 4 includes scenes 8 9 10 Program 6 includes scenes 12 13 14 15 16 Auto Pro Part 1 is Program 2 Auto Pro Part 2 is Program 3 Auto Pro Part 3 is Program 6 15 Classe LS 40 v1 0 v D o o o 3 o ee ea es ae INSTRUCTIONS ON U
22. ser Mode Standard Mode Users mode to change Basic Mode channel numbers 3 Extended Mode 2 User Mode A User Mode B 5 User Mode C 5 Edit User Mode Max Channel Max Channel XX Preset User modes PAN PAN CHO1 Select Programs Auto Pro Part 1 Program 1 10 Program 1 Select programs to be run Auto Pro Part2 Program 1 10 Program 2 Auto Pro Part 3 Program 1 10 Program 3 S Edit Program Program 1 Program Test STEP XX Testing program o Step 01 SCxxx Program in loop um Program 10 Step 64 SCxxx Save and exit a Edit Scenes Edit Scene 001 Pan Tilt Pan xxx Save and automatically Edit Scene Secne Time TIME xx xs return 250 Input By Outside manual scenes edit Rec Controller XX XX Automat scenes rec Default settings shaded 10 Classe LS 40 v1 0 Function Mode DMX address setting With this function you can adjust the desired DM X address via the Control Board Select Set DMX address via the encoder Press the encoder adjust the DMX address by turning the encoder Press the encoder to confirm Press the Mode Esc button in order return to the main menu Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel The display automatically shows the channel with a value changing Slave setting With this function you can define the device as slave Auto Program With this function you can run the internal program You can select the
23. ter unit sends Auto Program Part 1 to the Slave unit If set to Slave 2 the Slave unit receives Auto Program Part 2 To start a Auto Program please proceed as follows 1 Slave Setting Select Function Mode by turning the encoder Press the Enter button to confirm Select Set to slave by turning the encoder Press the Enter button to confirm Turn the encoder to select Slave 1 Slave 2 or Slave 3 Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 14 Classe LS 40 v1 0 2 Automatic Program Run Select Function Mode by turning the encoder Press the Enter button to confirm Select Auto Program by turning the encoder Press the Enter button to confirm Turn the encoder to select Master or Alone The selection Alone means Stand Alone mode and Master that the device is defined as master Press the Enter button to confirm Press the Mode Esc button in order to return to the main menu 3 Program selection for Auto Pro Part Select Edit program by turning the encoder Press the Enter button to confirm Select Select programs by turning the encoder Press the Enter button to confirm Turn the encoder to select Auto Pro Part 1 Auto Pro Part 2 or Auto Pro Part 3 and thus select which Slave program is to be sent Selection Part 1 means that the Slave unit runs the
24. the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Mounting the device CAUTION Please consider the GB7000 15 EN60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lighting is between 25 C to 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and th
Download Pdf Manuals
Related Search