4-Port 10/100Mbps +1/2 100FX Fiber Port
Contents
1.2. 15km ISW 511TS15 IP Camera Winter season of Country Steel Factory ISW 511T 100Base FX Fiber optic 100Base TX UTP w 0 1 4 Weather Station Desert IP Camera a ISW 621TS15 ff ISW 621TS15 15km IP Camera Winter season of Country t 100Base FX Fiber optic I I 100Base TX UTP I Installation Steps Step 1 Unpack the Industrial Fast Ethernet Switch Step 2 Check the DIN Rail is screwed on the Industrial Fast Ethernet Switch Please refer to DIN Rail Mounting section for DIN Rail installation If you want to wall mount the Industrial Fast Ethernet Switch then please refer to Wall Mount Plate Mounting section for wall mount plate installation Step 3 To hang the Industrial Fast Ethernet Switch on the DIN Rail track or wall please refer to the Mounting Installation section 25 amp _ Step 4 Step 5 Step 6 Power on the Industrial Fast Ethernet Switch Please refer to the Wiring the Power Inputs section for power input The power LED on the Industrial Fast Ethernet Switch will light up Please refer to the LED Indicators section for meaning of LED lights Prepare the twisted pair straight through Category 5 cable for Ethernet connection Insert one side of Category 5 cables into the Industrial Fast Ethernet Switch Ethernet port RJ 45 port and another side of category 5 cables to the network devices Ethernet
3. Step 5 Lightly press the button of DIN Rail for remove it from the track y 2 2 2 Wall Mount Plate Mounting To install the Industrial Fast Ethernet Switch on the wall please follows the instructions described below Step 1 Step 2 Step 3 Step 4 Step 5 ob 22 Remove the DIN Rail from the Industrial Fast Ethernet Switch loose the screws to remove the DIN Rail Place the wall mount plate on the rear panel of the Industrial Fast Ethernet Switch Use the screws to screw the wall mount plate on the Industrial Fast Ethernet Switch Use the hook holes at the corners of the wall mount plate to hang the Industrial Fast Ethernet Switch on the wall To remove the wall mount plate reverse steps above 3 Application In this paragraph we will describe how to install Industrial Fast Ethernet Switch and the installation points for the attention Fiber Switch ISW 621S15 1CS 2100 BS I ISW 621S15 al Serial over Ethernet device fi5km fea ICA 601 g f V Maintenance Shop 100Base TX UTP I I _ 100Base FX Fiber optic I I DI DO ee Subway 1 4 Fiber Switch ISW 511S15 sj Serial Device ISW 511S15 Server 100Base TX UTP _ 1 00Basee FX Fiber optic Factory s DIDO I 23 Weather Station Desert PMR ISW 511TS15 ig ISW 511TS15 IP Camera Data Center
4. 1 The wire gauge for the terminal block should be in the range between 12 24 AWG 2 Alarm relay circuit accepts up to 30V max 3A currents Industrial Switch The closed circuit will apen when the failure occurs ATTER apene Fault Alarm Contacts 3 amp 4 19 e 2 2 Mounting Installation This section describes how to install the Industrial Fast Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented In the installation steps below this Manual use IGS 801 PLANET 8 Port Industrial Gigabit Switch as the example However the steps for PLANET Industrial Switch amp Industrial Media Converter are similar 2 2 1 Install DIN Rail Mounting The DIN Rail is screwed on the Industrial Fast Ethernet Switch when out of factory When need to replace the wall mount application with DIN Rail application on Industrial Fast Ethernet Switch please refer to following figures to screw the DIN Rail on the Industrial Fast Ethernet Switch To hang the Industrial Fast Ethernet Switch follow the below steps Step 1 Screw the DIN Rail on the Industrial Fast Ethernet Switch 4 20 Step 2 Lightly press the button of DIN Rail into the track ad Step 3 Check the DIN Rail is tightly on the track Step 4 Please refer to following procedures to remove the Industrial Fast Ethernet Switch from the track 21 _
5. Contents INTRODUC TION RE EEE 6 1 1 Package Contents ssssssssssssnansssnsrrrnsnnnannnnssnrnnrnnnnnannasnnennne 6 1 2 How to Use This MEANUELuvuuavnasesnsmsmmea mme 6 1 3 Product Features sosna A 7 14 Product SD CINCALIOMS 25 2 sed sanien ie 8 NINE 14 TREN NN 14 2 1 1 Switch Front Panel seins 15 2 LED Ne 17 21 53 Switch Upper Panel Gaspar 17 2 1 4 Wiring the Power Inputs ssssssssseressssssnssssnssssnssnnne 18 2 1 5 Wiring the Fault Alarm Contact 19 222 Mounting Instalati cies dans us siennes 20 2 2 1 Install DIN Rail Mounting KG 20 2 2 2 Wall Mount Plate Mounting svoren 22 POMC AUION EEE EE iia 23 MT ON 27 4 1 Address Table aaranranvsnnnnnnrvnrsnnsnnnnnnrnnrnarnarnarnarnnrnnenannavnavner 27 4 2 Learning Lunden 27 4 3 Forwarding amp FENG HS 28 4 4 Store and Forward vvvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnen 28 4 5 ATEN den lee e ane 28 5 TROUBLESHOOTING ee 29 APPENDIX A NETWORKING CONNECTION 30 A 1 Switch s RJ 45 Pin Assignments uanrnnnrannernnrnnnnnnnnnnnnnnnnennne 30 A 2 RJ 45 cable Pin Assignments 52258 desis xessscsoirsentidarcemadencatan 30 1 INTRODUCTION 1 1 Package Contents Check the contents of your package for following parts e Industrial Fast Ethernet Switch x 1 e User s Manual x 1 e DIN Rail Kit x 1 e Wall Mount Kit x 1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton includ
6. Kit and Wall Mount Ear 9 1 Watts 31BTU Switch Specification Switch Processing Scheme Store and Forward Address Table 2K entries Buffer 1Mbit Back pressure for Half duplex Row Cone IEEE 802 3x Pause Frame for Full duplex Switch Fabric 1Gbps Throughput Packet Per Second Standards Conformance IEEE 802 3 Ethernet 10Base T IEEE 802 3u Fast Ethernet 100Base TX 100Base FX IEEE 802 3x Full duplex Flow control 0 74Mpps 64Bytes Standards Compliance IEC60068 2 32 Free Fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration era Operating 10 60 Degree C P Storage 40 85 Degree C Operating 5 to 90 Storage 5 to 90 Non condensing Regulation Compliance FCC Part 15 Class A CE Hardware Specification Ports 4 x 10 100Base TX Auto negotiation Auto MDI MDI X Copper 10Base T 2 pair UTP Cat 3 4 5 cable Cable 100meters max 100Base TX 2 pair UTP Cat 5 5e 6 cable 100meters max Humidity Operating 9 Ee 12 48V DC Redundant power with polarity Power Requirement reverse protection function Power Consumption Dissipation Installation DIN Rail Kit and Wall Mount Ear Switch Specification Switch Processing Scheme Store and Forward Buffer 1Mbit Flow Contra Back pressure for Half duplex IEEE 802 3x Pause Frame for Full duplex Switch Fabric 1Gbps Throughput Packet Per Second Standards Conformance IEEE 802 3 Ethernet 10Base T I
7. port RJ 45 port ex Switch PC or Server The UTP port RJ 45 LED on the Industrial Fast Ethernet Switch will light up when the cable connected with the network device Please refer to the LED Indicators section for LED light meaning Be sure the connected network devices support MDI MDI X If the network devices do not support MDI MDI Step 7 Step 8 i 26 X please use the crossover category 5 Cable to connect Insert fiber cable from the ISW 511 621 series or ISW 511T ISW 621T series to the fiber network TX RX must be paired at both ends The optical port LED on the Industrial Fast Ethernet Switch will light up when the cable connected with network device Please refer to the LED Indicators section for LED light meaning When all connections are set and the LEDs are light without any issue mean that the installation is complete 4 Switch Operation 4 1 Address Table The Industrial Fast Ethernet Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address Port No and etc This information comes from the learning process of Industrial Fast Ethernet Switch 4 2 Learning When one packet comes from any port of Industrial Fast Ethernet switch the Industrial Fast Ethernet Switch will record the source address port no and the other related information in address table This info
8. 4 Port 10 100Mbps 1 2 100FX Fiber Port Industrial Fast Ethernet Switch ISW 511 ISW 621 Series ISW 511T ISW 621T Series User s Manual Trademarks Copyright PLANET Technology Corp 2010 Contents subject revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipme
9. EEE 802 3u Fast Ethernet 100Base TX 100Base FX IEEE 802 3x Full duplex Flow control I 1o0Base FX 50 125um fiber Cable 9 125um fiber Fiber Optical fate 62 5 125um fiber 13 7 Watts 46BTU 0 74Mpps 64Bytes Standards Compliance IEC60068 2 32 Free Fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration Temperatur Operating 40 75 Degree C P Storage 40 85 Degree C Operating 5 to 90 Storage 5 to 90 Non condensing Regulation Compliance FCC Part 15 Class A CE Humidity Operating Hardware Specification 4 x 10 100Base TX Auto negotiation Auto MDI Ports MDLX 10Base T 2 pair UTP Cat 3 4 5 cable 100meters max 100Base TX 2 pair UTP Cat 5 5e 6 cable 100meters max Port 2 X 100Base FX Mode Single mode Distance 15km 12 48V DC Redundant power with polarity Power Requirement reverse protection function Power Consumption Dissipation 11 6 Watts 40BTU 11 _ Flow Control Back pressure for Half duplex IEEE 802 3x Pause Frame for Full duplex Switch Fabric 1 2Gbps Throughput 89M 4B Packet Per Second 0 89Mpps 64Bytes Standards Conformance IEEE 802 3 Ethernet 10Base T IEEE 802 3u Fast Ethernet 100Base TX 100Base FX IEEE 802 3x Full duplex Flow control Standards Compliance IEC60068 2 32 Free Fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration D ci Operating 10 60 Degree C E Storage 40 85 Deg
10. Upper Panel The upper panel of the Industrial Fast Ethernet Switch consist one terminal block connector within two DC power inputs Figure 2 5 shows the upper panel of the Industrial Fast Ethernet Switch satin ae ooo0o00o000 0J0 0006 OO Vi Vi yy V2 V2 Input O O L DC12 48V PWR1 Fault PWR2 Figure 2 5 Industrial Fast Ethernet Switch upper Panel 178 2 1 4 Wiring the Power Inputs The 6 contact terminal block connector on the top panel of Industrial Fast Ethernet Switch is used for two DC redundant powers input Please follow the steps below to insert the power wire 1 Insert positive negative DC power wires into the contacts 1 and 2 for POWER 1 or 5 and 6 for POWER 2 V1 V1 Yy V2 V2 Input O O L DC12 48V PWR1 Fault PWR2 V1 Vi V2 V2 2 Tighten the wire clamp screws for preventing the wires from loosing 1 2 3 4 5 6 Power 1 Fault Power 2 The wire gauge for the terminal block should be in the range between 12 24 AWG 2 1 5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below Inserting the wires the Industrial Fast Ethernet Switch will detect the fault status of the power failure or port link failure available for managed model and then forms an open circuit The following illustration shows an application example for wiring the fault alarm contacts 1 2 3 4 5 6
11. anufacturer s Name Planet Technology Corp Manufacturer s Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied Emission EN 55022 Class A 2006 Harmonic EN 61000 3 2 2006 Flicker EN 61000 3 3 1995 Al 2001 A2 2005 Immunity EN 55024 1998 Al 2001 A2 2003 ESD IEC 61000 4 2 2001 RS IEC 61000 4 3 2008 EFT Burst IEC 61000 4 4 2004 Surge IEC 61000 4 5 2005 CS IEC 61000 4 6 2008 Magnetic Field IEC 61000 4 8 2001 Voltage Disp IEC 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager Taiwan 22 Sep 2009 Kent J Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales Qplanet com tw http www planet com tw 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
12. dwidth o Prevents packet loss with back pressure Half Duplex and IEEE 802 3x PAUSE frame flow control Full Duplex o Backplane Switching Fabric ISW 511 ISW 511T Series 1Gbps ISW 621 ISW 621T Series 1 2Gbps o Integrated address look up engine support 2K absolute MAC addresses o 1Mbit on chip frame buffer on ISW 511 ISW 621 Series and ISW 511T ISW621T Series o Automatic address learning and address aging o CSMA CD Protocol 1e Industrial Case Installation o IP 30 Metal case Protection o DIN Rail and Wall Mount Design o 12 to 48V DC redundant power with polarity reverse protect function and connective removable terminal block for master and slave power o 10 to 60 Degree C operation temperature on ISW 511 ISW 511S15 ISW 621 ISW 621S15 o 40 to 75 Degree C operation temperature on ISW 511T ISW 511TS15 ISW 621T ISW 621TS15 1 4 Product Specifications Hardware Specification 4 x 10 100Base TX Auto negotiation Auto MDI MDI X Copper 10Base T 2 pair UTP Cat 3 4 5 cable Cable 100 meters max 100Base TX 2 pair UTP Cat 5 5e 6 cable 100 meters max 1x 100Base FX 50 125um fiber Cable 9 125um fiber Fiber Optical me 62 5 125ym fiber Multi mode Single mode Dimensions W x D x H 135mm x 97mm x 32mm Weight 436g 12 48V DC Redundant power with polarity Power Requirement i reverse protection function Power Consumption Dissipation Installation DIN Rail
13. he fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Industrial Fast Ethernet Switch the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines network traffic to its respective domain reducing the overall load on the network The Industrial Fast Ethernet Switch performs Store and Forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 4 5 Auto negotiation The STP ports on the Industrial Fast Ethernet Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by detect the modes and speeds at the second of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Du
14. ing the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Industrial Fast Ethernet Switch User Manual is structured as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Industrial Fast Ethernet Switch Chapter 3 Application The chapter explains the Industrial Fast Ethernet Switch application Chapter 4 Switch operation The chapter explains the Industrial Fast Ethernet Switch transmit operation Chapter 5 Troubleshooting The chapter explains the troubleshooting of the Industrial Fast Ethernet Switch Appendix A This chapter contains cable information of the Industrial Fast Ethernet Switch 1 3 Product Features Fn Port Model N tS Fiber gre Interface ode ame Poa name Optical pers Distance aa 511 mode mode ea 511T 1 x 100 FX ES 511S15 sinlemode mode 15km I ISW 511TS15 511TS15 isw 621 x 10 100 TX ae 621 mer 621T ES 621515 I ISW 621TS15 621TS15 Multi mode utinoce zen 2 x 100 FX Single mode Layer 2 Features o Complies with IEEE 802 3 IEEE 802 3u 10 100Base TX 100Base FX o Supports Auto negotiation and 10 100Mbps Half Full duplex mode for each copper port o High performance store and forward architecture broadcast storm control runt CRC filtering eliminates erroneous packets to optimize the network ban
15. nt has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human x health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET 4 Port 10 100Mbps 1 2 100FX Industrial Fast Ethernet Switch User s Manual For ModelS ISW 511 ISW 621 ISW 511T ISW 621T Series Revision 1 1 April 2010 Part No EM ISW 511 621 v1 1 2350 AH0150 001 1 Table of
16. ol function allows Industrial Fast Ethernet Switch supported routers and servers to directly connect to this device for fast reliable data transfer 2 1 1 Switch Front Panel Figure 2 1 amp 2 2 amp 2 3 amp 2 4 shows a front panel of Industrial Fast Ethernet Switch 0 P1 P2 FAULT d z H e BNUWO Z a 20 10 ve ve vinnner ISW 511 vinnaer ISW 621 Figure 2 1 ISW 511 ISW 511S15 Figure 2 2 ISW 621 ISW 621515 front panel front panel 15 FAULT 10 ve A 10 100 Y LNK ACT ISW 5 1 1T Figure 2 3 ISW 511T ISW 511TS15 front panel 16 e BNUWO Z a 20 ve A 10 100 vink acr ISW 621T Figure 2 4 ISW 621T ISW 621TS15 front panel 2 1 2 LED Indicators SC unetion Green Lit indicate the power 1 has power po Green Lit indicate the power 2 has power FAULT Gen Lit indicate the either power 1 or power 2 has no power 100 ree Fiber Lit indicate the Fiber port is successfully Optical connecting to the network at 100Mbps Lit indicate the Switch is successfully connecting to the network at 100Mbps 10 100 Green Copper Off indicate that the Switch is successfully connecting to the network at 10Mbps Fiber Lit indicate the link through that port is Optical successfully established BIEN Blink indicate that the Switch is actively Copper sending or receiving data over that port 2 1 3 Switch
17. perating 13 2 INSTALLATION This section describes the functionalities of the Industrial Fast Ethernet Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing In the following section the term Industrial Fast Ethernet Switch means the ISW 511 ISW 621 series and ISW 511T ISW 621T series 2 1 Product Description The PLANET ISW 511 ISW 621 series and ISW 511T ISW 621T series are 4 Port 10 100Mbps 1 2 100FX Fiber Port Industrial Fast Ethernet Switch with non blocking wire speed performance and new slim type with IP 30 metal shape for easily deployment in Heavy Industrial demanding environments With 1 1 2Gbps internal switching fabric the Industrial Fast Ethernet Switch can handle extremely large amounts of data in a secure topology linking to a backbone or high capacity servers The Industrial Fast Ethernet Switch has 2K MAC address table and offers wire speed packets transfer performance without risk of packet loss The stable throughput of the device makes it ideal for most Ethernet environments All RJ 45 copper interfaces support 10 100Mbps Auto negotiation for optimal speed detection through RJ 45 Category 5 4 or 3 cables Support standard for Auto MDI MDI X that can detect the type of connection to any Ethernet device without requiring special straight or crossover cables The Flow Contr
18. plex mode 28 5 TROUBLESHOOTING This chapter contains information to help you solve issues If the Industrial Fast Ethernet Switch is not functioning properly make sure the Industrial Fast Ethernet Switch was set up according to instructions in this manual The Link LED is not light Solution Check the cable connection of the Industrial Fast Ethernet Switch Performance is bad Solution Check the speed duplex mode of the partner device The Industrial Fast Ethernet Switch is operating at Auto negotiation mode by default and if the partner is set to half duplex then the performance will become bad Link LED is light but the traffic is irregular Solution Check that the attached device is not set to dedicate full duplex Some devices use a physical or software switch to change duplex modes Auto negotiation may not recognize this type of full duplex setting Why does the Industrial Fast Ethernet Switch not connect to the network Solution 1 Check every port LED on the Industrial Fast Ethernet Switch 2 Try another port on the Industrial Fast Ethernet Switch to make sure the cable is installed properly while make sure the cable is the right type 3 Turn off the power and turn on the power again after a while 29 E _ APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ 45 Pin Assignments 10 100Mbps 10 100Base TX RJ 45 Connector pin assignment MDI MDI X Contact Media Dependant In
19. ree C Operating 5 to 90 Storage 5 to 90 Non condensing Regulation Compliance FCC Part 15 Class A CE Model ISW 621T ISW 621TS15 Hardware Specification 4 x 10 100Base TX Auto negotiation Auto MDI Ports MDI X 10Base T 2 pair UTP Cat 3 4 5 cable Copper Cable 100meters max 100Base TX 2 pair UTP Cat 5 5e 6 cable 100meters max Port 2 x 100Base FX Cable alen 9 125um fiber Fiber Optical 62 5 125um fiber Mode Multi mode Single mode Humidity Operating Dimensions W x D x H 135mm x 97mm x 32mm Weight 4429 12 48V DC Redundant power with polarity Power Requirement reverse protection function Power Consumption Dissipation Installation DIN Rail Kit and Wall Mount Ear Switch Specification Switch Processing Scheme Store and Forward 16 Watts 54BTU Address Table Buffer 1 Mbit Flow Control Back pressure for Half duplex IEEE 802 3x Pause Frame for Full duplex Switch Fabric 1 2Gbps Throughput 89M 4B Packet Per Second 0 89Mpps 64Bytes Standards Conformance IEEE 802 3 Ethernet 10Base T IEEE 802 3u Fast Ethernet 100Base TX 100Base FX IEEE 802 3x Full duplex Flow control Standards Compliance IEC60068 2 32 Free Fall Stability testing IEC60068 2 27 Shock IEC60068 2 6 Vibration seat Operating 40 75 Degree C P Storage 40 85 Degree C Operating 5 to 90 Storage 5 to 90 Non condensing Regulation Compliance FCC Part 15 Class A CE Humidity O
20. rmation will be used to decide either forwarding or filtering for future packets 4 3 Forwarding amp Filtering When one packet comes from some port of the Industrial Fast Ethernet Switch it will also check the destination address besides the source address learning The Industrial Fast Ethernet Switch will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will transmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Industrial Fast Ethernet Switch will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered 27 4 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Industrial Switch stores the incoming frames in an internal buffer and checks any error from the frames before transmission No error packets occurrence it is the best choice when a network needs efficiency and stability The Industrial Fast Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required T
21. terface Cross ne transm Media Dependant Interface gt eoe oeeo O E as Neues e posa e Not used A 2 RJ 45 cable Pin Assignments The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable Straight Cable SIDE 1 SIDE 2 12345678 SIDE1 1 White Orange 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green 4 Blue 4 Blue 5 White Blue 5 White Blue 12345678 SIDE2 6 Green 6 Green 7 White Brown 7 White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 12345678 SIDE 1 White Orange 1 White Green 2 Orange 2 Green 3 White Green 3 White Orange 4 Blue 4 Blue 5 White Blue 5 White Blue 12345678 SIDE2 6 Green 6 Orange 7 White Brown 7 White Brown 8 Brown 8 Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 31 _ D PLANET Networking amp Communication EC Declaration of Conformit For the following equipment Type of Product 4 1 4 2 100FX Port Multi mode Industrial Ethernet Switch Model Number ISW SI1 ISW SI1S15 ISW S11T ISW S11TS15 ISW 621 ISW 621S15 ISW 621T ISW 621TS15 Produced by M
Download Pdf Manuals
Related Search