TB-3 CS Manual (Rev. 070423.1)
Contents
1. Removing the slide 7 OPERATION 8 APPENDIX 9 Maintenance 9 Specifications 9 Warranty and service 10 Warranty 10 Service notes 10 Warner Instruments TB 3 CS Manual Rev 070423 1 3 The TB 3 CS Thermal Stage Insert has been designed for use with Prior s NanoScanZ piezo stage system The TB 3 CS uses reliable and precise Peltier technology to control the temperature in dispos2. TB 3 CS Manual Rev 070423 1 W Waarrnneerr IInnssttrruum meennttss TThheerrm maall SSttaaggee H Heeaatteerr CCoooolleerr IInnsseerrtt ffoorr PPrriioorr N NaannooSSccaannZZ SSttaaggee SSyysstteem m M Mooddeell TTBB 33 CCSS Warner Instruments 1125 Dixwell Avenue Hamden CT 06514 800 599 4203 203 776 0664 203 776 1278 fax Warner Instruments TB 3 CS Manual Rev 070423 1 Table of Contents INTRODUCTION 4 GENERAL 4 SETUP 5 General procedure 5 Connecting the Thermal Cooling Module 5 Mounting onto the NanoScanZ stage 6 Loading the slide 6
3. able rectangular chambered slides and cover glasses available from Nunc Beckton Dickinson and other sources Stage insert temperatures can be stably maintained from 0 to 50 C An integral water jacket uses recirculation water from Warner s TCM 1 Thermal Cooling Module to remove excess heat from the Peltier electronics within the TB 3 CS The efficiency of specimen heating and cooling has dependence on the type of slide and on the presence of condensation Thermal transfer efficiency also depends on a good mechanical attachment of the slide to its support for this reason we provide two sets of slide clamps to both position the slide and to bring it into close apposition with the stage insert The base of the TB 3 CS has a thermal barrier designed to reduce the occurrence of condensation when the unit is cooled to below the dew point The TB 3 CS Thermal Stage Insert is designed to fit directly into the NanoScanZ stage and uses the same mounting and positioning provisions as for other sample holders that fit the NanoScanZ THIS EQUIPMENT IS NOT DESIGNED NOR INTENDED FOR USE ON HUMAN SUBJECTS Warner Instruments TB 3 CS Manual Rev 070423 1 4 GENERAL Peltier control of heating and cooling is a proven and direct method for providing temperature regulation to devices comprised of metal components The quiet performance of the Peltier device coupled with the high thermal conductivity of the metal components makes for a ro
4. aecide part of the TCM 1 to the fill reservoir Refill the bottle with water and add to the reservoir This will act to prime the TCM 1 pump 8 Fill a 500 ml beaker with water and submerge the open ends of the two Tygon tubes from steps 5 and 6 into the beaker 9 Power the TCM 1 Solution should begin moving from the beaker through the TB 3 CS through the TCM 1 and finally back into the beaker Add more fluid to the beaker as needed The flow path is full once bubbles stop coming out of the outflow tube 10 Turn off the power to the TCM 1 and remove the short length of Tygon tubing attached to the WATER JACKET CONNECTING TUBE connected to the lower TCM 1 fluid flow port 11 Join the full length Tygon tube attached to the TB 3 CS to the open WATER JACKET CONNECTING TUBE to complete the flow path 12 Power the TCM 1 and check for leaks Mounting onto the NanoScanZ stage 1 Place the TB 3 CS into the cutout on the NanoScanZ stage The fit should be an exact match 2 Refer to the leveling procedure in your NanoScanZ user s manual and if needed adjust the leveling set screws of the TB 3 CS using the supplied Allen wrench 3 Once proper leveling has been achieved you may secure the TB 3 CS to the stage using the four 2 x 10 mm mounting screws 4 Make a connection between the TB 3 CS and CL 100 at this time Loading the slide If your slide has dimensions of less than 1 x 3 inch If your slide has dimension
5. bust and efficient system The TB 3 CS Thermal Stage Insert has been specifically designed for use with Prior s NanoScanZ piezo stage system and it can accommodate any slide having a 1 x 3 in 25 x 76 mm footprint Slightly smaller footprint slides most commonly the 1 x 2 inch 25 x 50 mm slides are also supported test fit before use The TB 3 CS is designed to be used with Warner s CL 100 Bipolar Temperature Controller and TCM 1 Thermal Cooling Module The CL 100 provides feedback driven regulation of heating cooling power and the TCM 1 quietly and effectively dissipates the heat generated by the operation of the integral TB 3 CS Peltier device Each TB 3 CS Thermal Stage Insert is supplied with The thermal stage insert Two black slide clamps Two aluminum slide clamps One lift out tool One 0 028 inch Allen wrench Four 2 x 10 mm mounting screws Two 3 meter lengths of in OD Tygon tubing Warner Instruments TB 3 CS Manual Rev 070423 1 5 SETUP A fully assembled TB 3 CS including the CL 100 and TCM 1 is shown to the right Instructions for the use of the CL 100 and TCM 1 are left their respective user s manuals General procedure The general assembly procedure is to attach the TCM 1 to the TB 3 CS away from the microscope and to check for secure leak free connections This is followed by positioning the TB 3 CS into the NanoScanZ stage Then leveling and securing the insert A connection is the
6. cement part Factory service if required will be expedited to minimize the customer s inconvenience B Instruments are inspected immediately upon receipt and the customer is notified if the repair is not covered by the warranty Repairs can often be completed in 1 2 days from our receipt of the instrument C If factory service is required please observe the following instructions 1 Package the instrument with at least 2 inches of cushioning on all sides Use the original shipping carton if it is available 2 Insure the shipment for its full value 3 Include with the shipment an explanation of the problem experienced IMPORTANT CUSTOMERS OUTSIDE OF THE U S Please be sure to contact us before return shipping any goods We will provide instructions so that the shipment will not be delayed or subject to unnecessary expense in clearing U S Customs Warner Instruments
7. l Dimensions 3 6 x 2 5 x 0 4 inch L x W x D 9 2 x 6 4 x 1 0 cm L x W x D Cable Length 2 5 m Connector Type 15 pin Male D Weight 150 g Warranty 1 year Warner Instruments TB 3 CS Manual Rev 070423 1 10 Warranty and service Warranty The model TB 3 CS is covered by our Warranty to be free from defects in materials and workmanship for a period of one year from the date of shipment If a failure occurs within this period we will either repair or replace the faulty component s This warranty does not cover failure or damage caused by physical abuse lack of maintenance or electrical stress inputs exceeding specified limits In the event that instrument repairs are necessary shipping charges to the factory are the customer s responsibility Return charges will be paid by Warner Instruments Normal business hours are 8 30 AM to 5 30 PM EST Monday through Thursday and 8 30 AM to 5 00 PM on Friday Our offices are located at 1125 Dixwell Avenue Hamden CT 06514 and we can be reached by phone at 800 599 4203 or 203 776 0664 Our fax number is 203 776 1278 In addition we can be reached by e mail at support warneronline com or through the web at http www warneronline com Service notes Please refer all questions regarding service to our Customer Service department A Should service be required please contact the factory A problem can sometimes be easily corrected by our shipping a repla
8. n made between the TB 3 CS and CL 100 Finally your sample slide in inserted into the stage insert and your experiment begun Connecting the Thermal Cooling Module Note This step should be performed away from the microscope TCM 1 upper flow port 1 First review the assembly instructions for the TCM 1 Thermal Cooling Module We will use a modified procedure 2 The goal is to connect flow lines from a fill reservoir to the TB 3 CS to the TCM 1 and finally back to the fill reservoir Once the system is filled the lines entering and exiting the fill reservoir are joined 3 Begin by connecting the WATER JACKET CONNECTING TUBES supplied with the TCM 1 to the upper and lower fluid flow ports on the rear of the TCM 1 as shown to the right 4 Now cut the two 3 meter Tygon tubes supplied with the TB 3 CS to length Attach these tubes to the TB 3 CS perfusion flow ports as shown to the right 5 Join the open end of one the aforementioned tubes to the upper WATER JACKET CONNECTING TUBE which you attached to the TCM 1 flow port in step 3 TB 3 perfusion flow ports 6 Now take a short length of Tygon tubing and connect to the other WATER JACKET CONNECTING TUBE attached to the lower fluid flow port on the rear of the TCM 1 Warner Instruments TB 3 CS Manual Rev 070423 1 6 7 Next remove the screw on the top of the TCM 1 to reveal the fill port for the internal fluid reservoir Add the supplied alg
9. rea to measure the temperature at a point of interest 5 Adjust the SET TEMP on the CL 100 to the desired operating temperature Allow the system to thermally stabilize Monitor the temperature at the point of interest using the TA 29 thermistor 6 Make any temperature adjustments on the CL 100 to compensate for heat loss to the surrounding area 7 Additional adjustment of the heater set point may be required if any of the following change substantially during an experiment Perfusion solution flow rate if present Temperature of solution entering the heater if flowing solutions Ambient room temperature Air currents around chamber Efforts to minimize these factors will be rewarded Warner Instruments TB 3 CS Manual Rev 070423 1 9 APPENDIX Maintenance The TB 3 CS can be cleaned with soap and water should the outside surface become dirty Salt solutions and TCM 1 perfusion solutions can be corrosive to metal components and can shorten the life of the heater cooler if left in contact with the unit during storage If storing the TB 3 CS for an extended length of time the TB 3 CS TCM 1 flow path should be drained flushed with distilled water and blown dry Specifications Minimum Temperature 0 C Maximum Temperature 50 C Accuracy 0 1 C Water Jacket Ports Delrin barbed connectors 0 12 ID x 0 147 OD Controller CL 100 Bipolar Temperature Controller Physica
10. s of 1 x 3 inch Begin by placing one of the black slide clamps on one end of the stage insert opening Do not place the black clamp until after the slide has been inserted Warner Instruments TB 3 CS Manual Rev 070423 1 7 Insert the slide into the holder Making sure the slide is up against the black slide clamp Insert the slide into the holder Place the other black slide clamp into the space adjacent to the slide The slide should now be securely positioned so that it cannot move laterally in the holder Place the two black slide clamps into the stage insert on top of the outboard edges of the slide to clamp it into place Place the first top slide clamp into position as shown Place the first top slide clamp into position as shown Place the second top slide clamp into position as shown Place the second top slide clamp into position as shown Removing the slide The slide and black clamps can be easily removed by use of the included removal tool Insert the flat end under the edge of the item to be removed and lift out Warner Instruments TB 3 CS Manual Rev 070423 1 8 OPERATION 1 Turn on the power to TCM 1 2 Turn on the power to CL 100 3 Set the CL 100 MODE SELECTOR SWITCH into auto the INTERNAL EXTERNAL SELECTOR SWITCH to internal see the CL 100 user s manual and the LOOP SPEED SELECTOR SWITCH to medium 4 If desired place a TA 29 thermistor into the bath a
Download Pdf Manuals
Related Search