JY997D13501F USER`S MANUAL
Contents
1. Associated Manuals JY997D16501 MODEL CODE 09R516 JY997D28701 MODEL CODE 09R519 Manual name Description Explains FX3U Series PLC specifications for I O wiring installation and maintenance FX3U Series User s Manual Hardware Edition FX3UC Series User s Manual Hardware Edition FX USB AW FX3U USB BD User s Manual USB Driver Installation Edition Explains FX3UC Series PLC specifications for I O wiring installation and maintenance Explains procedures for installing the USB driver software for the FX USB AW or FX3U USB BD JY997D32601 FX Series User s Manual Data Communication Edition Explains N N network Parallel Link Computer Link Non Protocol communication by RS and RS2 instructions FX2N 232 IF JY997D16901 MODEL CODE 09R715 How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Applicable standards FX3U USB BD units made in June 2005 or later comply with the EC Directive EMC Directive Further information can be found in the following manual However the FX3UC 32MT LT does not comply with the EC Directive EMC Directive Refer to the FX3U Series Hardware Manual Manual No JY997D18801 1 Outline The FX3U USB BD hereinafter called USB BD is an expansion board equipped with an USB port MINI B plug female for USB communication By connecting the USB BD and2. 1 Outline The FX3U USB BD hereinafter called USB BD is an expansion board equipped with an USB port MINI B plug female for USB communication By connecting the USB BD and a personal computer with USB ports program transfer to a PLC main unit and monitoring can be performed 1 1 Incorporated Items Verify that the following product and items are included in the package Product USB communication expansion board FX3U USB BD M3 tapping screws Included items USB driver software CD ROM USB cable 3m 118 1 User s Manual this manual 1 2 External Dimensions and Part Names 46 1 1 81 53 5 2 11 Special adapter connector cover is removed MASS Weight 20g 0 05Ibs USB cable included with the product 1 Mounting holes 2 03 2 2 RD LED Lighting while receiving data LED color red 3 SD LED Lighting while sending data LED color red 4 USB Connector 5 Main unit connector 6 Special adapter connector cover 7 Special adapter connector 8 USB Connector To FX3U USB BD MINI B plug male 9 USB Connector To personal computer MINI B plug female A plug male 2 Installation INSTALLATION PRECAUTIONS DANGER e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAUTIONS CAUTION e Use the pr
3. AW FX3U USB BD i Click Finish to close the wizard Click Finish The installation of the USB Serial Port software will finish The CD ROM USB driver software can be removed from the personal computer at this time 6 2 Windows Vista For the installation procedure of the driver refer to the following manual FX USB AW FX3U USB BD User s Manual USB Driver Installation Edition 7 Installation Confirmation of Driver Procedure for confirming the installation of the driver is described below Windows XP example follows e In Windows XP click Start gt Control Panel Performance and Maintenance System gt Hardware gt Device Manager and the window below will be displayed Please confirm the COM number to which the driver is allocated COM and LPT If using Windows 98 Windows 98SE Windows Millennium Edition or Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer Control Panel gt System gt Device Manager in the menu of the personal computer e f using Windows Vista A screen that is equivalent to the one below is displayed by clicking Start Control Panel Hardware and Sound gt Device Manager in the menu of the personal computer When user account control is enabled Only when user account control is enabled will the user account control screen be displayed Click Con
4. This product requires USB Driver Installation for each USB port to be connected Connect the product to a driver installed USB port or install the driver to the current port This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the sy
5. accident STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor e Do not drop the product or do not exert strong impact doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of the product TRANSPORT AND STORAGE PRECAUTIONS CAUTION e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation e The expansion board cannot be connected to FX3UC Series PLC other than FX3UC 32MT LT e Only one expansion board can be used per main unit Additional expansion boards such as the FX3U 232 BD FX3U 422 BD or FX3U 485 BD cannot be installed used together with the FX3U USB BD e FX3U USB BD and a personal computer are connected and the PLC is turned on and then an operations such as write read and monitor are tried for the first time using a programming tool a communication error message may be displayed In such a case clear the message and try the operations again e If a communication error message is indicated while operating the programming tool when executing Write to PLC Read from PLC or Monitor disconnect the USB cable once from either the personal
6. computer or the FX3U USB BD and connect it again Then clear the error message and choose Write Read or Monitor again e The programming tool may not be operated properly due to a contact failure at connectors or wire breakage Make sure to save the program before transferring or changing it 10 Troubleshooting e If communication cannot be established between the PLC and a personal computer using FX3U USB BD confirm the following status by checking SD LED and RD LED in FX3U USB BD The status of SD LED and RD RED The status of SD LED and RD LED Contents Blinking Communicating correctly e Confirm that the power is supplied to the personal computer e Confirm the personal computer and the PLC are connected properly with the specified cable e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual SD Extinguished Blinking Data receiving e Confirm that the power is supplied to PLC e The PLC will not operate when a configuration that exceeds the DC 5V or DC 24V capacity is used It will also be impossible to communicate normally Extinguished Confirm that the specified cable is used to connect the personal computer and PLC e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual RD e When driver installation is required after already establishing USB communication
7. either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Click Continue Anyway 3 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for FX USB A W FX3LU USB BD Click Finish to close the wizard Click Finish If using Windows 2000 or Windows XP proceed to step 4 If Windows 98 Windows 98SE or Windows Millennium Edition is used installation of the USB Serial Port software begins and ends automatically The CD ROM can be removed from the personal computer at this time The installation of the USB driver software is finished 4 The following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Serial Port If your hardware came with an installation CD ap or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Click Next gt The installation of the USB Serial Port software will begin If using Windows 2000 a screen to select the location of the installation files is displaye
8. screwdriver as shown in the figure on the right lift the dummy expansion board cover fig A making sure not to damage the circuit board or electronic parts 3 Remove the dummy expansion board cover fig A perpendicularly away from the main unit 4 Make sure the expansion board fig B is in parallel with the main unit fig C and attach it to the expansion board connector 5 Fix the expansion board fig B to the main unit using the provided M3 tapping screws fig D Tighten to a torque of 0 3 to 0 6 N m 3 Specifications 3 1 Applicable PLC Model name FX3U Series PLC FX3UC 32MT LT Applicability Ver 2 20 or later from first production Ver 1 00 or later from first production e The expansion board cannot be connected to FX3UC Series PLCs other than the FX3UC 32MT LT e Only one expansion board can be used per main unit additional expansion boards such as the FX3U 232 BD FX3U 422 BD or FX3U 485 BD cannot be installed used together with the FX3U USB BD For details on the system configuration refer to the following manual Refer to the FX Series User s Manual Data Communication Edition 3 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals However please do not perform any dielectric withstand voltage tests or insulation resistance tests to this product Refer to the FX3U Series User s Manual Har
9. In other OS depending on the PC environment Driver installation may occur automatically USB driver software folder structure The folder structure is as follows according to the USB driver software version Ver 1 10 or higher lt CD ROM Drive gt lt WinXP_2000_ME_98 gt The USB driver for Windows 98 Windows 98SE Windows Millennium Edition Me Windows 2000 and Windows XP is stored lt WinVista gt The USB driver for Windows Vista is stored Versions previous to Ver 1 10 The USB driver for software previous to Ver 1 10 does not have a folder structure The USB driver is stored in the main directory of the CD ROM drive 6 1 Windows 98 Windows 98SE Windows Millennium Edition Windows 2000 and Windows XP Please install the driver by the following procedure The installation procedure is explained when connecting to a personal computer with Windows XP e Windows 98 Windows 98SE Windows Millennium Edition and Windows 2000 the installation method will vary 1 When the USB cable is connected to the personal computer the following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for FX3U USB BD If your hardware came with an installation CD or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a li
10. a personal computer with USB ports program transfer to a PLC main unit and monitoring can be performed 1 1 Incorporated Items Verify that the following product and items are included in the package Product USB communication expansion board FX3U USB BD M3 tapping screws Included items USB driver software CD ROM USB cable 3m 118 1 User s Manual this manual 1 2 External Dimensions and Part Names if 53 5 2 11 MASS Weight 20g 0 05lbs Special adapter connector cover is removed USB cable included with the product 1 Mounting holes 2 03 2 2 RD LED Lighting while receiving data LED color red 3 SD LED Lighting while sending data LED color red 4 USB Connector 5 Main unit connector 6 Special adapter connector cover 7 Special adapter connector 8 USB Connector To FX3U USB BD MINI B plug male 9 USB Connector To personal computer MINI B plug female A plug male 2 Installation INSTALLATION PRECAUTIONS DANGER e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAUTIONS CAUTION e Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosiv
11. al USB Driver Installation Edition 9 Caution on use STARTUP AND MAINTENANCE PRECAUTIONS DANGER e Before a program or setting on line or off line change is performed please read all relevant manuals and confirm safety aspects Incorrect operation may damage the product or cause an accident STARTUP AND MAINTENANCE PRECAUTIONS Z CAUTION e Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor e Do not drop the product or do not exert strong impact doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of the product TRANSPORT AND STORAGE PRECAUTIONS CAUTION e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation e The expansion board cannot be connected to FX3UC Series PLC other than FX3UC 32MT LT e Only one expansion board can be used per main unit Additional expansion boards such as the FX3U 232 BD FX3U 422 BD or FX3U 485 BD cannot be installed used together with the FX3U USB BD e FX3U USB BD and a personal computer are connected and the PLC is turned on and then an operations such as write read and monitor are tried for the first time using a programming tool a communication error messa
12. ard cover fig A perpendicularly away from the main unit 4 Make sure the expansion board fig B is in parallel with the main unit fig C and attach it to the expansion board connector 5 Fix the expansion board fig B to the main unit using the provided M3 tapping screws fig D Tighten to a torque of 0 3 to 0 6 N m 3 Specifications 3 1 Applicable PLC Model name FX3U Series PLC FX3UC 32MT LT Applicability Ver 2 20 or later from first production Ver 1 00 or later from first production e The expansion board cannot be connected to FX3UC Series PLCs other than the FX3UC 32MT LT e Only one expansion board can be used per main unit additional expansion boards such as the FX3U 232 BD FX3U 422 BD or FX3uU 485 BD cannot be installed used together with the FX3U USB BD For details on the system configuration refer to the following manual Refer to the FX Series User s Manual Data Communication Edition 3 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals However please do not perform any dielectric withstand voltage tests or insulation resistance tests to this product Refer to the FX3U Series User s Manual Hardware Edition Refer to the FX3UC Series User s Manual Hardware Edition 3 3 Power Supply Specification Item Specification e 15mA DC 5V 5V DC power is supplied from the main unit e 30
13. at the specified cable is used to connect the personal computer and PLC e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual RD e When driver installation is required after already establishing USB communication This product requires USB Driver Installation for each USB port to be connected Connect the product to a driver installed USB port or install the driver to the current port This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medic
14. d Please select the CD ROM drive 5 The screen of 2 is displayed Only in Windows XP Click Continue Anyway 6 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for J FX USB AW FX3U USB BD Click Finish to close the wizard Click Finish The installation of the USB Serial Port software will finish The CD ROM USB driver software can be removed from the personal computer at this time 6 2 Windows Vista For the installation procedure of the driver refer to the following manual FX USB AW FX3uU USB BD User s Manual USB Driver Installation Edition 7 Installation Confirmation of Driver Procedure for confirming the installation of the driver is described below Windows XP example follows e In Windows XP click Start Control Panel Performance and Maintenance System gt Hardware gt Device Manager and the window below will be displayed Please confirm the COM number to which the driver is allocated COM and LPT If using Windows 98 Windows 98SE Windows Millennium Edition or Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer Control Panel gt System gt Device Manager in the menu of the personal computer e f using Windows Vista A screen that is equivalent to the one below is displa
15. dware Edition Refer to the FX3UC Series User s Manual Hardware Edition 3 3 Power Supply Specification Item Specification e 15mA DC 5V 5V DC power is supplied from the main unit e 30mA DC 5V 5V DC power is supplied from the USB connector of personal computer Current consumption 3 4 Communication Specifications Item Specification Transmission USB2 0 For full speed standard isolation Photocoupler isolation Between communication line and CPU Maximum T 5m 196 9 at most Included cable is 3m 118 1 transmission distance Baud Rate 9600 19200 38400 57600 115200 bps Port USB MINI B plug female 3 5 System Requirements Item Specification Microsoft Windows 98 Windows 98SE Microsoft Windows Millennium Edition Windows Me Microsoft Windows 2000 Microsoft Windows XP Microsoft Windows Vista SWUID5C GPPW E GX Developer FX PCS WIN E OSs 3 Software 1 The USB driver for Windows 98 Windows 98SE Windows Millennium Edition Windows 2000 and Windows XP included in the USB driver software Ver 1 10 is used This USB driver is the same driver as the USB driver for software previous to Ver 1 10 2 Use the USB driver for Windows Vista from the USB driver software Ver 1 10 3 GX Developer Ver 8 23Z or later is applicable to the FX3U Series PLC Its Ver 8 13P or later is applicable to the FX3UC 32MT LT Series PLC For fur
16. e gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or exposed to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur e Use screwdrivers carefully when performing installation work thus avoiding accident or product damage e When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions e Do not touch the conductive parts of the product directly Doing so may cause device failures or malfunctions e Connect expansion board securely to their designated connectors Loose connections may cause malfunctions The following section describes the installation method for the FX3U FX3UC 32MT LT Series PLC FX3U Series PLC is used for the following example For more details on installation and removal refer to the PLC main unit manual Refer to the FX3U Series User s Manual Hardware Edition Refer to the FX3UC Series User s Manual Hardware Edition 2 1 Installation Method 1 Power off the PLC Disconnect all the cables connected to the PLC Demount the PLC from the DIN rail 2 Using a flat head screwdriver as shown in the figure on the right lift the dummy expansion board cover fig A making sure not to damage the circuit board or electronic parts 3 Remove the dummy expansion bo
17. e to the Found New Hardware Wizard This wizard helps you install software for FX3U USB BD c If your hardware came with an installation CD lt gt or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Insert the included CD ROM into the personal computer s CD ROM drive Click Next gt The installation of the USB driver software will begin If using Windows 98 and Windows 98SE A window to select the location of the installation files will appear Specify the USB driver software version as follows Ver 1 10 or higher Please select the Include this location in the search and install by specifying the WinXP_2000 ME_98 directory from the CD ROM drive Versions previous to Ver 1 10 Please select the CD ROM drive If using Windows Millennium Edition and Windows 2000 A window to select the location of the installation files will appear Please select the CD ROM drive 2 The following screen is displayed Only in Windows XP Hardware Installation A The software you are installing for this hardware Fx USB AWw Fx3U USB BD has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system
18. er s Manual Hardware Edition 4 System Configuration Connected equipment and connected cable PLC FX3U USB BD Personal computer USB driver software Install MiTSuISHE For details of the programming communication refer to the following manual Refer to the FX Series User s Manual Data Communication Edition 5 Connecting Procedure 1 Power off the PLC 2 Connect the USB MINI B plug male connector of the USB cable to the FX3U USB BD 3 Connect the USB A plug male connector of the USB cable to the personal computer 4 Turn ON the power supply of the PLC 5 Turn ON the power supply of the personal computer 6 Driver Installation When the USB cable is connected to the personal computer the Found New Hardware Wizard screen is displayed Install USB driver software from the included CD ROM Caution The driver is not installed properly when canceled during the installation To complete the installation uninstall the driver and install again For the uninstallation procedure of the driver refer to the following manual FX USB AW FX3U USB BD User s Manual USB Driver Installation Edition Note This product requires USB Driver Installation for each USB port to be connected To use multiple USB ports connect this product to each port and install the driver individually With Windows Vista Driver installation will occur automatically
19. ge may be displayed In such a case clear the message and try the operations again e If a communication error message is indicated while operating the programming tool when executing Write to PLC Read from PLC or Monitor disconnect the USB cable once from either the personal computer or the FX3U USB BD and connect it again Then clear the error message and choose Write Read or Monitor again e The programming tool may not be operated properly due to a contact failure at connectors or wire breakage Make sure to save the program before transferring or changing it 10 Troubleshooting e If communication cannot be established between the PLC and a personal computer using FX3U USB BD confirm the following status by checking SD LED and RD LED in FX3U USB BD The status of SD LED and RD RED The status of SD LED and RD LED Contents Blinking Communicating correctly e Confirm that the power is supplied to the personal computer e Confirm the personal computer and the PLC are connected properly with the specified cable e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual SD Extinguished Blinking Data receiving e Confirm that the power is supplied to PLC e The PLC will not operate when a configuration that exceeds the DC 5V or DC 24V capacity is used It will also be impossible to communicate normally Extinguished Confirm th
20. ine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system a a MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
21. l USB Driver Installation Edition Note This product requires USB Driver Installation for each USB port to be connected To use multiple USB ports connect this product to each port and install the driver individually With Windows Vista Driver installation will occur automatically In other OS depending on the PC environment Driver installation may occur automatically USB driver software folder structure The folder structure is as follows according to the USB driver software version Ver 1 10 or higher lt CD ROM Drive gt lt WinXP_2000_ME_98 gt The USB driver for Windows 98 Windows 98SE Windows Millennium Edition Me Windows 2000 and Windows XP is stored lt WinVista gt The USB driver for Windows Vista is stored Versions previous to Ver 1 10 The USB driver for software previous to Ver 1 10 does not have a folder structure The USB driver is stored in the main directory of the CD ROM drive 6 1 Windows 98 Windows 98SE Windows Millennium Edition Windows 2000 and Windows XP Please install the driver by the following procedure The installation procedure is explained when connecting to a personal computer with Windows XP e Windows 98 Windows 98SE Windows Millennium Edition and Windows 2000 the installation method will vary 1 When the USB cable is connected to the personal computer the following screen is displayed Found New Hardware Wizard Welcom
22. mA DC 5V 5V DC power is supplied from the USB connector of personal computer Current consumption 3 4 Communication Specifications Item Specification Transmission USB2 0 For full speed standard isolation Photocoupler isolation Between communication line and CPU Maximum o 5m 196 9 at most Included cable is 3m 118 1 transmission distance Baud Rate 9600 19200 38400 57600 115200 bps Port USB MINI B plug female 3 5 System Requirements Item Specification Microsoft Windows 98 1 Windows 98SE Microsoft Windows Millennium Edition Windows Me Microsoft Windows 2000 Microsoft Windows XP Microsoft Windows Vista SWUID5C GPPW E GX Developer FX PCS WIN E OSs 3 Software The USB driver for Windows 98 Windows 98SE Windows Millennium Edition Windows 2000 and Windows XP included in the USB driver software Ver 1 10 is used This USB driver is the same driver as the USB driver for software previous to Ver 1 10 2 Use the USB driver for Windows Vista from the USB driver software Ver 1 10 3 GX Developer Ver 8 23Z or later is applicable to the FX3U Series PLC Its Ver 8 13P or later is applicable to the FX3UC 32MT LT Series PLC For further details concerning alternative inapplicable programming tool setting refer to the following manual Refer to the FX3U Series User s Manual Hardware Edition Refer to the FX3UC Series Us
23. nd New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for a FX USB AW FX3LU USB BD Click Finish to close the wizard Click Finish If using Windows 2000 or Windows XP proceed to step 4 If Windows 98 Windows 98SE or Windows Millennium Edition is used installation of the USB Serial Port software begins and ends automatically The CD ROM can be removed from the personal computer at this time The installation of the USB driver software is finished 4 The following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Serial Port If your hardware came with an installation CD lt gt or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Click Next gt The installation of the USB Serial Port software will begin If using Windows 2000 a screen to select the location of the installation files is displayed Please select the CD ROM drive 5 The screen of 2 is displayed Only in Windows XP Click Continue Anyway 6 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for J FX USB
24. oduct within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or exposed to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur e Use screwdrivers carefully when performing installation work thus avoiding accident or product damage e When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions e Do not touch the conductive parts of the product directly Doing so may cause device failures or malfunctions e Connect expansion board securely to their designated connectors Loose connections may cause malfunctions The following section describes the installation method for the FX3U FX3UC 32MT LT Series PLC FX3U Series PLC is used for the following example For more details on installation and removal refer to the PLC main unit manual Refer to the FX3U Series User s Manual Hardware Edition Refer to the FX3UC Series User s Manual Hardware Edition 2 1 Installation Method 1 Power off the PLC Disconnect all the cables connected to the PLC Demount the PLC from the DIN rail 2 Using a flat head
25. side JY997D13501F B ie E JAPANESE B ENGLISH Changes for the Better a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEG F FX3U USB BD USER S MANUAL F X 3u This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective May 2008 Specifications are subject to change without notice 2005 Mitsubishi Electric Corporation Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories lt DDANGER and CAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by A CAUTION may also cause severe injury It is important to follow all precautions for personal safety
26. st or specific location Advanced Click Next to continue Insert the included CD ROM into the personal computer s CD ROM drive Click Next gt The installation of the USB driver software will begin If using Windows 98 and Windows 98SE A window to select the location of the installation files will appear Specify the USB driver software version as follows Ver 1 10 or higher Please select the Include this location in the search and install by specifying the WinXP_2000 ME_98 directory from the CD ROM drive Versions previous to Ver 1 10 Please select the CD ROM drive If using Windows Millennium Edition and Windows 2000 A window to select the location of the installation files will appear Please select the CD ROM drive 2 The following screen is displayed Only in Windows XP Hardware Installation The software you are installing for this hardware FX USB AW FX3U USB BD has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Click Continue Anyway 3 The following screen is displayed Fou
27. stem afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN side JY997D13501F B K E JAPANESE B ENGLISH a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEGF FX3U USB BD USER S MANUAL F X 3u Changes for the Better This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective May 2008 Specifications are subject to change without notice 2005 Mitsubishi Electric Corporation Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories lt gt DANGER and CAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous Z CAUTION conditions resulting in medium or slight personal injury or ph
28. ther details concerning alternative inapplicable programming tool setting refer to the following manual Refer to the FX3U Series User s Manual Hardware Edition Refer to the FX3UC Series User s Manual Hardware Edition 4 System Configuration Connected equipment and connected cable PLC USB driver software FX3U USB BD Personal computer Install _ gt USB cable for personal computer connection included with the product A USB port For details of the programming communication refer to the following manual Refer to the FX Series User s Manual Data Communication Edition 5 Connecting Procedure 1 Power off the PLC 2 Connect the USB MINI B plug male connector of the USB cable to the FX3U USB BD 3 Connect the USB A plug male connector of the USB cable to the personal computer 4 Turn ON the power supply of the PLC 5 Turn ON the power supply of the personal computer 6 Driver Installation When the USB cable is connected to the personal computer the Found New Hardware Wizard screen is displayed Install USB driver software from the included CD ROM Caution The driver is not installed properly when canceled during the installation To complete the installation uninstall the driver and install again For the uninstallation procedure of the driver refer to the following manual FX USB AW FX3U USB BD User s Manua
29. tinue when displayed Device Manager File Action Yiew Help 8 R Ports COM amp LPT J Communications Port COM1 F B Printer Port LPT1 MB Processors Sound video and game controllers Se Storage volumes System devices z Universal Serial Bus controllers FX USB AW FxX3U USB BD z A Tekeli AANNAM O tte ew Check following FX USB AW FX3U USB BD is indicated at A FX USB AW FX3U USB BD COM is indicated at B indicates the COM number used in FX3U USB BD Install the driver again when is displayed Select the programming software COM number as the COM number currently assigned on the screen above Setting GX Developer Double click Online gt Transfer setup gt Serial of personal computer side I F Select the same COM number as the COM number of the personal computer when the personal computer side I F serial setting Dialog Box appears Click OK of Connection Setup screen to end Transfer Setup PC side F COM COM 3 Tr 8 Uninstalling Driver For the uninstallation procedure of the driver refer to the following manual FX USB AW FX3U USB BD User s Manual USB Driver Installation Edition 9 Caution on use STARTUP AND MAINTENANCE PRECAUTIONS DANGER e Before a program or setting on line or off line change is performed please read all relevant manuals and confirm safety aspects Incorrect operation may damage the product or cause an
30. yed by clicking Start Control Panel Hardware and Sound gt Device Manager in the menu of the personal computer When user account control is enabled Only when user account control is enabled will the user account control screen be displayed Click Continue when displayed 2 Device Manager File Action Yiew Help iie ME Ports COM amp LPT Communications Port COM1 F B aF Printer Port LPT1 MB Processors Sound video and game controllers Storage volumes System devices 2 Universal Serial Bus controllers FX USB AW FX3U USB BD A Tate AAO LICN tte ee i Check following FX USB AW FX3U USB BD is indicated at A FX USB AW FX3U USB BD COM is indicated at B indicates the COM number used in FX3U USB BD Install the driver again when is displayed Select the programming software COM number as the COM number currently assigned on the screen above Setting GX Developer Double click Online gt Transfer setup gt Serial of personal computer side I F Select the same COM number as the COM number of the personal computer when the personal computer side I F serial setting Dialog Box appears Click OK of Connection Setup screen to end Transfer Setup PC side F COM COM3 Tr 8 Uninstalling Driver For the uninstallation procedure of the driver refer to the following manual FX USB AW FX3uU USB BD User s Manu
31. ysical damage Depending on the circumstances procedures indicated by A CAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals JY997D16501 MODEL CODE 09R516 JY997D28701 MODEL CODE 09R519 Manual name Description Explains FX3U Series PLC specifications for I O wiring installation and maintenance FX3U Series User s Manual Hardware Edition FX3UC Series User s Manual Hardware Edition FX USB AW FX3U USB BD User s Manual USB Driver Installation Edition Explains FX3UC Series PLC specifications for I O wiring installation and maintenance Explains procedures for installing the USB driver software for the FX USB AW or FX3U USB BD JY997D32601 FX Series User s Manual Data Communication Edition Explains N N network Parallel Link Computer Link Non Protocol communication by RS and RS2 instructions FX2N 232 IF JY997D16901 MODEL CODE 09R715 How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Applicable standards FX3U USB BD units made in June 2005 or later comply with the EC Directive EMC Directive Further information can be found in the following manual However the FX3UC 32MT LT does not comply with the EC Directive EMC Directive Refer to the FX3U Series Hardware Manual Manual No JY997D18801
Download Pdf Manuals
Related Search