Baby Baby Blue
Contents
1. BABY BABY BLUE OWNER S MANUAL Part 0066562000 07 03 Copyright 2003 SWR2. clipped waveform or Square wave will quickly heat up the voice coils in speakers and if operating continually while clipping eventually will burn the voice coils and cause the speakers to fail This is especially important to remember when running the amp at 4 ohms as you are operating at or near the maximum capacity of the power amplifier With extreme settings on the Gain and Master Volume controls you may hear audible clipping of the power amp and the power amp clip LED should illumi nate If so you have exceeded the maximum capacity of the power amp POWER AMP CLIPPING CAN CAUSE DAMAGE BOTH TO ITSELF AND YOUR SPEAKER CABINETS Back off on the Gain and Master con trols to help smooth out the peaks Remember it s always better to have a little too much power than just barely enough Obviously the Baby Baby Blue is a small combo meant for small gigs and studio work If you find yourself constantly wanting more power than the Baby Baby Blue provides either a Tell your bandmates to turn down b Tell the monitor engineer to turn you up 6 better option Take the time to investigate getting an external power amp for the additional speaker cabinets to supplement your rig d best option Investigate getting a larger combo for those gigs where more power and volume is need ed EXTENSION SPEAKER OUTPUT JACK One 1 4 phone jack has been provided for connection of the Baby Baby Blue to your desired extension spe
3. the Master Volume is up After all EQ settings and the Aural Enhancer are set the Gain control should be raised until the preamp clip LED barely flashes when your loudest note is struck This will insure maximum signal to noise ratio and prevent unwanted clipping of the preamp section Note The Gain can serve as an EFFECTS SEND LEVEL ADJUSTMENT If your effect is being overdriv en turn down the Gain control and readjust your Master Volume for overall loudness PREAMP CLIP LED The preamp clip LED will light whenever the preamp tone section or output buffer reach clipping run out of headroom This function does NOT monitor the first tube stage of the Passive input See that section for more info In the event the clip indicator lights turn down the Gain control Since this circuit monitors the tone con trols boosting any one of them can cause the clip LED to activate Once again you may leave the tone control at its desired level but turn the Gain control down further Note Even though the Preamp Clip LED lighting indicates that at some point the preamp is clipping no harm is being done to your amplifier However clipping of the power amp can cause damage to your speakers and is not recommended AURAL ENHANCER The Aural Enhancer is a feature that s been on just about every SWR amplifier since the company s incep tion in 1984 and is a trademark part of the SWR Sound people have come to know and love It was develope
4. BLUE OWNER S MANUAL 11 CONNECTING AN EXTERNAL EFFECTS DEVICE TO THE EFFECTS LOOP Obtain two high quality shielded patch cables preferably as short as possible Route them in the most direct way possible Running patch cables over the top of the Baby Baby Blue as with any induce hum in the cables and is not recommended Take one cable and connect it from the Effects Send jack on the Baby Baby Blue to the input of your external effects device Take the second cable and con nect it from the output of your external effects device to the Effects Return jack on your Baby Baby Blue To set levels follow the instructions as previously listed in the Effects Blend Control heading under Front Panel Features EFFECTS SEND This jack s primary function is to send a post EQ signal to an external effects device for use in the Baby Baby Blue s Effects Loop However it can also be used as 1 A line level output for use in conjunction with an additional slave power amp or powered speaker cabinet 2 An unbalanced output suitable for recording or live mixing board purposes The output impedance of the Effects Send jack is 100 Ohms EFFECTS RECEIVE This jack s primary function is to complete the Effects Loop circuit by routing the post external effects device signal back into the power amp of the Baby Baby Blue where it can be blended back in with the original signal by using the Effects Blend control on
5. Guide thoroughly and completely so that you can realize the full potential of your new Baby Baby Blue Bass Combo Amplifier Once again thanks for your purchase and for letting SWR help Amplify Your Future Sincerely SWR BABY BABY BLUE OWNER S MANUAL 1 Note Please take a moment to verify that the following items were included in your SWR Baby Baby Blue packaging AC Cable User Guide SWR Catalog BABY BABY BLUE FRONT PANEL FEATURES e High passive active and low active sensitivity 1 4 inputs Gain control with LED peak preamp clipping indicator e Aural Enhancer Control 3 band semi parametric EQ EQ bypass switch e Effects Blend Control e Effects Loop bypass switch e Master Volume Control with LED peak power amp clipping indicator BABY BABY BLUE REAR PANEL FEATURES e Side chain effects loop e Balanced XLR Output with select switch for Line or Direct Mode e XLR pad level control with ground lift switch e 1 4 Line Out Jack e Tuner Out Jack Headphone Jack e 1 4 Extension Speaker Output Jack Speaker Fuse 4 amp fast blo e Line Fuse 3AG 3 amp slo blo 120V e 3 Position Tweeter Mode Switch on back of cabinet SPECIFICATIONS ELECTRONICS Note All measurements were taken with a line voltage of 120 Maximum power at 1kHz under clipping 120 Watts RMS 8 ohms 160 Watts RMS 4 ohms Power Amp Distortion 1kHz 0 02 THD 100 Watts RMS 8 ohms 0 03
6. MANUAL HOW IMPEDANCE AFFECTS POWER RATINGS People often have questions about impedance What is it The root of the word impedance is the verb impede which means to block or resist That s what impedance is resistance to power Power amps themselves do not have a pre determined impedance They deliver power at whatever imped ance the speaker cabinet tells it to That s why you hear the term slave amp ampilifiers only do what they re told So if someone tells you that they have a 4 ohm power amp their terminology and under standing of the concept is way off the mark Unlike power amps every speaker cabinet has a pre determined impedance rating measured in ohms In most cases this rating is either 4 or 8 ohms though there may still be some old 2 ohm creakers out there The higher the impedance of the speaker cabinet the more resistance to power it will offer The lower the resistance of the speaker cabinet the less resistance to power it will offer In other words HIGHER IMPEDANCE MEANS LESS POWER CAN ENTER THE SPEAKER CABINET LOWER IMPEDANCE MEANS MORE POWER CAN ENTER THE SPEAKER CABINET You may be thinking that you ve found the solution to the universe just use speaker cabinets with really low impedances and you can get skull crushing power out of your amplifier right Wrong There s a catch Power amps have limits as to how low an impedance they can drive safely This is what s known as a
7. SETTINGS Not sure where to start Try any of these ALL TUBE PRE AMP 140 WATT POWER AMP FREQUENCY gt LEVEL 25 XE 2 SEL a a A 55 5 15 250 1 25K 1 5K 7 5K MID RANGE TREBLE SOS EQUALIZATION ROCK REFERENCE SERES FREQUENCY gt LEVEL 750 Ke 1 25K MIO RANGE FQUAIZATON NEY 15 15K 7 5K TREBLE REGGAE BABY BABY BLUE OWNER S MANUAL 7 ALL TUBE PRE AMP 160 WATT POWER AMP ALL TUBE PRE AMP 160 WATT POWER AMP oft FREQUENCY gt LEVEL ER 3828 500 gt rt 6 1 20 125K LSK 75K MID RANGE EQUALIZATION ALL TUBE PRE AMP 160 WATT POWER AMP FREQUENCY gt LEVEL OK VE a S 160 pr 3Ke 5 415 40 0 250 1 25 BASS MID RANGE ATION ALL TUBE PRE AMP 160 WATT POWER AMP FREQUENCY Co LEVEL IDON 4 w 6K gt 250 125K isk 75K MID RANGE TREBLE EQUALIZATION lt a STUDIO 8 BABY BABY BLUE OWNER S MANUAL CONTROLLING FEEDBACK AND SUSTAIN UPRIGHT BASSES The original Baby Blue was and continues to be a very popular model for use with upright basses largely because of the compact size and ultra flexible EQ The low mid to hi mid areas 80 Hz to 1kHz which are now easily adjustable on the semi parametric EQ can be extremely useful in correcting feedback in acoustic bass guitars or upright basses If you are getting a sli
8. THD 100 Watts RMS 4 ohms Intermodulation Distortion 8 ohms 100 Watts RMS 60 7kHz 4 1 Frequency Response power amp 300 at 10 Hz and 22kHz System Distortion Gain and Master Volume full enhancer and tone controls set flat 1 2 0 5 THD 2 BABY BABY BLUE OWNER S MANUAL BABY BABY BLUE OWNER S MANUAL 3 Sensitivity for full output 8 ohms 1kHz Passive Active Input Jack 10 millivolts Active Input Jack 50 millivolts Input Impedance Passive Active Input Jack 800k ohms Active Input Jack 60k ohms Effects Return Jack 27k ohms Output Impedance Effects Send Jack 100 ohms Line Out Jack 100 ohms Tuner Out Jack 100 ohms Headphone Jack 100 ohms Signal to Noise Ratio unweighted 72db 7 millivolts typical Equivalent Input Noise 2 5 micro volts Chassis Material Aluminum CABINET Outer Dimensions 13 7 8 W x 19 Hx 13 7 8 D Internal Impedance 8 ohms Cabinet Construction Interlocking dado joints glued and nailed covered in blue carpet Cabinet Material 7 ply 5 8 waterproof void free birch or maple plywood Speakers 1 10 PAS driver proprietary to SWR 1 LeSon TLX 1 Piezo Tweeter Passive Crossover Components Capacitors polyester Coils 1 7 milli henry iron choke low DCR custom made Grill Stamped 16GA steel chrome plated Total Weight 39 Ibs BABY BABY BLUE GETTING STARTED Remove the cable from the accessory pack and connect it from the ampl
9. do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so that the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SHOULD YOUR SWR AMPLIFIER REQUIRE SERVICE OR REPAIR PLEASE USE THE FOLLOW ING PROCEDURE 1 Locate your original receipt showing date of purchase model and serial number 2 Determine the closest Authorized FMIC Service Center to your location The fastest way to get a complete list of Authorized FMIC Service Centers is on the web at http www mrgearhead con fad allservice html You can also get this information by calling FMIC Consumer Relations at 480 596 7195 3 To receive warranty service return the complete product to an Authorized FMIC Electronics Service Center with proof of purchase during the applicable warranty period Transportation costs are not included in this Limited Warranty Defective products that qualify for coverage under this warranty will be repaired or replaced at FMIC s discretion with a like or comparable product without charge SWR For a complete list of Authorized FMIC 0 00 Service Centers and the latest SWR Scottsdale AZ 85250 2618 USA 480 596 9690 news interviews and more check out FAX 480 367 5262 EMAIL custserve fenderusa com our website WEB swrsound com swrsound com
10. fluorescent lighting directly above you or in close proximity especially when using single coil pickups 5 A cell phone in your right pocket that s interacting with the electronics in your bass don t laugh this actually happens But in the case of a true ground loop this switch can often times solve the problem TUNER OUT JACK The Tuner Out function marked To Tuner Input on the rear of your Baby Baby Blue allows the user to plug their instrument tuner into this jack and tune up without having to unplug and go back and forth from amp to tuner This feature is totally isolated from the rest of the preamp and will function regardless of the settings on the front panel Being isolated on a side chain avoids loading down of the instrument which can cause a loss in dynamic range To use this feature connect a shielded patch cord from the To Tuner Input jack on your Baby Baby Blue to the input jack on your tuner Turn the amplifier on and you re ready to go If you do not wish to monitor your sound during the tuning process you may turn down the Master Volume LINE OUT JACK This jack provides an audio output located later in the signal chain than the Effects Send jack This signal is post EQ and post effects loop but still before pre the Master Volume control You should use this jack when using an effects device in the effects loop and wish to achieve 1 A line level output for use in conjunction with an ad
11. the front panel However it can also be used as 1 A power amp input jack If for some reason you wished to bypass the entire front end and use the Baby Baby Blue strictly as a powered speaker cabinet you could take the output of whatever line level audio source you wished and connect it to this jack Then set the Effects Blend control to the full clock wise WET position Use the Master control to set the overall level and your Baby Baby Blue is now a powered speaker cabinet 2 An input for pre recorded music for playing along and practicing purposes To accomplish this insert a CD player or other sound source into the Effects Receive jack It must be a MONO 1 4 plug that goes into this input so you ll have to use stereo to mono cable adaptor of some kind You can adjust the level of recorded music versus the live sound of your instrument by using both the Effects Blend control the more clockwise the control the more pre recorded music signal you ll hear and the volume control of your CD or other audio source The mixed sound will be heard through your speakers Besides pre recorded music this is also an excellent way to practice along with a drum machine Input impedance of the Receive jack is 27k Ohms minimum Note Inserting a plug into the Effects Receive jack activates the Effects Blend control The control receives this command through the ground created by the phone plug making contact with the jack The pl
12. Master Volume should be turned down Constant clipping of a power amplifier can lead to overheating of the electronic components and can cause serious harm to your speaker system It also sounds pretty bad Speakers that have failed due to continuous clipping of a power amplifier are easy to detect and are generally not covered under warranty Once again to correct this situation turn down the Master Volume BABY BABY BLUE REAR PANEL FEATURES BALANCED XLR OUTPUT The Balanced XLR out is a true electronically balanced output suitable for studio and front of house live mixing consoles The level present at this output can be adjusted by using the XLR Pad control see the XLR Pad Control section below for more details The signal appearing at the Balanced Output is gov erned by the setting of the two position XLR Mode switch located directly below it Line Direct In the DIRECT position the Balanced Output signal comes from directly after the first stage of the special ly selected 12AX7 preamp tube giving you the sound of your instrument and some added warmth In other words it becomes an active TUBE direct box In this position no front panel controls are functional In the LINE position all front panel controls are functional except the Master Volume control and the sig nal is essentially the same as that heard through your speaker system If you are using an external effects device in the effects loop that signal wi
13. NPUT JACK The Active input jack should be used with instruments having a built in on board preamp or other sound sources that will produce output levels greater than 1 volt RMS The number of bass manufacturers has increased significantly over the years and it s impossible to try and keep track of them all Generally if you have very hot pickups and or tone controls installed in your instrument and you use them to boost the level of your bass signal 10 dB or more you may find the Active input more compatible The best judge iS your own ears If you re using a keyboard or bass pedal with the Baby Baby Blue we have found the best choice to be the Active input Note Using the Active input with passive basses active instruments will always employ a battery may result in a loss of high end transients Players who roll off their high end starting at about 2kHz or prefer a darker sound may find this input more to their liking If you hear some distortion with your active bass and are using the Active Input make sure the preamp clip LED indicator is not lighting If the preamp stage is not being driven into clipping replace the battery in your instrument 4 BABY BABY BLUE OWNER S MANUAL GAIN CONTROL The Gain control adjusts the volume of the preamp section Since the Gain control is similar to a pad a small amount of signal will be heard even with the Gain control rotated fully counter clockwise MIN if
14. SWR CORONA USA OWNER S MANUAL Baby Baby Blue IMPORTANT SAFETY INSTRUCTIONS CAUTION TO REDUCE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER OR BACK NO USER SER VICEABLE PARTS INSIDE PLEASE REFER TO A QUALIFIED SERVICE TECHNICIAN A READ INSTRUCTIONS All safety and operation instructions should be read before the product is operated B RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference HEED WARNINGS All of the warnings on this product and in the operating instructions should be adhered to D FOLLOW INSTRUCTIONS All operating and use instructions should be followed E CLEANING Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a slightly damp cloth for cleaning F WATER AND MOISTURE Do not use this product near water for example near a swimming pool wet basement and the like G ACCESSORIES Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product H VENTILATION Slots and openings in the unit are provided for ventilation and to ensure reliable operation of the product to protect it from overheating thus these openings must not be blocked or covered This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation
15. aker cabinet Only SPEAKER CABLE of 18 gauge or heavier the heavier the cable the lower the gauge should be used to connect your Baby Baby Blue to your extension speaker system Do not use shielded instrument cable for this purpose as this can result in intermittent power loss cause your amp to oscil late and damage itself and or your speakers and render the cable useless Recommended SWR extension speaker enclosures for use with the Baby Baby Blue include e Goliath Junior 1 2x10 8 ohms e Bass Monitor 12 Son Of Bertha 1x15 e Workingman s 1x10T e Workingman s 2x10T SPEAKER FUSE The speaker fuse is provided to protect your speakers in the unlikely event of a power amp failure or to protect your power amplifier from incorrect speaker impedances or hookups Size and rating of the fuse is 4 amp fast blo Do not defeat the purpose of this feature by using a higher rated fuse as it can damage your amplifier and void your warranty The fuse can open as a result of a fault in an extension speaker cable the speakers themselves or the power amp being sent well into clipping With this in mind it is wise to carry extra fuses at all times 14 BABY BABY BLUE OWNER S MANUAL LINE FUSE A C OR MAINS FUSE This fuse is provided to protect the internal electronics against power surges etc It also protects the unit against itself should one of the internal components fail If this fuse should open replace it with the same type o
16. and the power amp is designed with extremely high quality bi polar devices Each type of device was chosen for its performance and reliability in the application used The chassis of the Baby Baby Blue comprised of aluminum because of its superior electrical and thermal characteristics and light weight All primary elec trical components are U L approved and SWR uses Beldon Cable for all shielded wire All units are assembled by hand and individually soundtested in the U S A at our factory in Southern California 16 BABY BABY BLUE OWNER S MANUAL BABY BABY BLUE OWNER S MANUAL 7 BABY BABY BLUE LIMITED WARRANTY The BABY BABY BLUE from SWR Sound Corporation is warranted to the original consumer pur chaser for TWO YEARS from the date of purchase against defects in materials and workmanship provided that it is purchased from an Authorized SWR dealer This warranty applies only to prod ucts purchased in the USA or Canada This warranty is VOID if the unit has been damaged due to accident improper handling installa tion or operation shipping damage abuse or misuse unauthorized repair or attempted repair or if the serial number has been defaced or removed FMIC reserves the right to make such determi nation on the basis of inspection by an Authorized FMIC Service Center All liability for any incidental or consequential damages for breach of any expressed or implied warranties is disclaimed and excluded herefrom Some states
17. d to help bring out the fundamental low notes of the bass guitar enhance the high end transients and reduce certain frequencies that help mask the fundamentals The ultimate result is 1 A more transparent sound especially noticeable when slapping and popping 2 It can make a passive bass take on an active type of quality when set at positions of 2 o clock or further clockwise Let s take a second to learn how the Aural Enhancer works Think of it as a variable tone curve that changes depending on where you set the Aural Enhancer control knob As you raise the control clockwise from the MIN position you are elevating a whole range of sound lows mids and highs at a variety of frequency points selected specifically because they re different than those selected for the individual tone controls of most SWR units This remains true up to about the 2 o clock position This position a favorite for many users brings out both the low end fundamentals and crisp highs and at the same time adds a little lower midrange to help cut through the band However if you go further clockwise and past the 2 00 position selected mids will start to drop off specifically a group of frequencies centered around 200 Hz At this point and after the effect becomes much more pronounced However the curves involved here are gentle 85 opposed to the very extreme curves you can create by boosting or cutting the Active Tone Cont
18. ditional power amp or powered extension speaker Cabinet 2 An unbalanced output suitable for recording or live mixing board purposes EFFECTS LOOP As mentioned previously in the Effects Blend Control section of the manual the Effects Blend circuit in your Baby Baby Blue is similar to that used on recording consoles with the effects loop on a side chain to the normal circuit Unless the Effects Blend control is set to the full wet position you will always get the full sound of your instrument AND get the diversity an external effects unit offers Use of the effects loop will reduce the noise generated by external effects units as compared to using the effect between your instrument and the input jack though many people use it in this fashion anyway This is because the loop is after the preamp gain stages The Effects Loop is compatible with most individual or multi effect external effects devices Many effects devices on the market have input level adjustments For instance some units have a switch that you can set for either 20 dB or 4 dB In all cases these should be set for 0 dB if available or 4 dB The level going to your effect is controlled by the Gain control on the front panel Note The Effects Loop is used in conjunction with the Effects Blend control on the front panel When the Effects Blend Control is in the full counter clockwise DRY position no effects will be heard This is normal BABY BABY
19. f fuse and rating Do not defeat the purpose of this feature by using a higher rated fuse as it can void your warranty Proper size of the AC fuse for all countries is 3AG Proper rating of the fuse is as follows United States 120V 3 amp slo blo Japan 100V 3 amp slo blo Europe 230V 240V 1 6 amp slo blo A C CORD RECEPTACLE This receptacle accepts a standard A C power cable supplied with the Baby Baby Blue in the United States used with almost all current musical professional and household electronic devices We recom mend great care when packing up If it does become misplaced a replacement cable can be purchased at almost any music or computer store Note The rating for this cable is 3 conductor 10 amperes minimum Look for this rating on the cable Make sure the cable is plugged in all the way in both the amp and the wall socket TWO POSITION SPEAKER ON OFF SWITCH Located on the rear of the speaker cabinet section this two position switch can defeat the entire speaker system if desired Its primary function is to allow for silent practicing in conjunction with a set of stereo headphones but it can also be used as an overall mute switch The upper position marked On allows the speaker system to operate in its normal capacity The lower position marked Off defeats both the speaker and the tweeter in the Baby Baby Blue THREE POSITION TWEETER SWITCH Located on the rear of the speaker cabinet section this th
20. g to qualified service personnel 0 DAMAGE REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord has been damaged 2 If liquid has been spilled or objects have fallen into the product 3 If the product has been exposed to rain water or other conductive liquids 4 If the product does not operate normally by following the operating instructions 5 If the product has been dropped or damaged in any way 6 When the product exhibits a distinct change in performance P REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Q SAFETY CHECK Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition R HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products that produce heat INTRODUCTION Congratulations on your purchase of the SWR Baby Baby Blue Bass Combo Amplifier You now own the leg endary SWR Sound in its most portable configuration to date You may read the name of the product and think Baby Baby Blue is that a t
21. ght amount of feedback from your instrument try the following a Set your volume to a point where the feedback is just occurring but not out of control b Raise the Level control of the first or second band of the semi parametric EQ that is activated to about 7 dB 6 Slowly rotate the Frequency control from left to right At some point on either the first or second band during the rotation of the Frequency control the feedback should get more intense This is the fre quency area that needs attention and once you find it you should leave the Frequency control at this position for a second to confirm the diagnosis d Now adjust the Level control counter clockwise in other words cut the level of this frequency until the feedback disappears You may find that as you raise the volume you may need to further cut the Level control to achieve the desired playing volume In this example when the feedback becomes more intense listen closely to make sure it is the same pitch as the original feedback Feedback can be induced at different frequencies by boosting their levels and you certainly don t need two problem areas Also by reversing the technique above you can achieve greater sustain in certain areas or on certain notes Finally you can also use these guidelines to correct hot or dead spots on the neck of your instru ment or inherent in your speaker system EFFECTS BLEND CONTROL The Effects Blend Control blends the
22. ifier to a standard wall outlet Make sure that the Gain and Master Volume controls are set to the minimum position fully counter clockwise Locate the power switch on the right side of the front of the unit and turn the amplifier on Upon powering up don t be surprised if you hear a small pop This is absolutely normal Plug your instrument into the desired input jack refer to Front Panel Features for greater detail Turn your instrument s volume up to at least 75 of maximum and slowly adjust the gain control Once you begin to play your instrument and you see the red light marked preamp clip over the gain control illumi nate back off the gain a bit Now turn up the Master Volume and you should hear the sound of your instrument amplified through the Baby Baby Blue For more detailed information please read the entire manual carefully so that you can fully realize the potential of the your new Baby Baby Blue BABY BABY BLUE FRONT PANEL FEATURES INPUT JACKS Both input jacks accept a standard 1 4 phone plug and both inputs can be used at the same time Since the two inputs are totally independent no loss in volume or tone will occur by using two instruments simul taneously However the main applicational use for the two separate input jacks is their difference in level as the Passive Active input has five times more gain than the Active input In other words it s not neces sarily intended as a s
23. is provided or the manufacturer s instructions have been adhered to I GROUNDING This product is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug J POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon them paying particular attention to cords at plugs and the point where they exit the product K LIGHTNING For added protection of this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet This will prevent damage to the product due to lightning and power line surges L OVERLOADING Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock M OBJECT AND LIQUID ENTRY Never push objects of any kind into this product through the openings as they may touch dan gerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product N SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous volt age or other hazards Refer all servicin
24. ked ourselves what would happen if we combined these electronics with a single SWR Professional Line 10 speaker the same as used in our famous Goliath 111 4x10 speaker cabinet and Super Redhead 2x10 combo in the smallest cabinet configuration possible The result is the Baby Baby Blue the easiest way to take the SWR sound with you wherever you go The electronics have been preserved in their original form The speaker cabinet was designed for maximum low end response and tone while still maintaining a weight under 40 Ibs and size designed for one hand car rying into the gig The features 3 band semi parametric EQ with extended third band high end Aural Enhancer switchable EQ and side chain effects loop provide maximum tone and flexibility for both onstage and in the studio The sound is pure SWR And of course every Baby Baby Blue is still assem bled by hand and individually soundtested in the USA at our factory in Southern California It s all part of SWR s commitment to continued improvement and refinement of even our most popular models so that we can continue to assist today s bassist in the pursuit of the ultimate goal finding equip ment that not only does the job but actually enhances the overall musical experience and contributes to the creative process Everyone here at SWR sincerely hopes that the purchase of your Baby Baby Blue helps you get there from here and beyond Please take the time to read your User
25. ll also be present when in the LINE position dictated by the setting of the Effects Blend control on your Baby Baby Blue When in this position the output level will be affected by the Gain control on the front panel as well as the XLR Pad control It s worth noting that changing the level of the Gain control will affect the signal present at your speakers the Effects Send jack the Line Out jack and the Balanced Output while the XLR Pad control affects the level present at the Balanced Output only For this reason it s usually better to set your Gain control in accordance with the directions in the Gain Control previously listed in the Front Panel Features section of this manual and to use the XLR Pad control to set the level specifically for the Balanced Output Wiring for the XLR jack at the Balanced Output is as follows Pin 1 ground Pin 2 plus Pin 3 minus American Standard Note Turn off transients appear at the Balanced Output when the amplifier is shut down We recom mend that equipment being used in conjunction with the Balanced Output be turned down off or dis connected BEFORE the unit is turned off XLR MODE SWITCH LINE DIRECT This two position switch determines the signal present at the Balanced XLR Output jack as described in the section directly above In simple terms 1 Direct pre EQ post first tube stage 2 Line post EQ pre master volume Make sure the switch is set either to f
26. n trol It cuts or boosts the frequency set by the FREQUENCY control which is the outer knob If the LEVEL control is in its center position or flat that band will be essentially off In this case moving the fre quency outer knob with the level control in the flat position will have NO AFFECT on the sound or tonal structure The level control MUST be in a cut or boost off center for any change in tone to be audible How will you know when the level control is in the center or flat position Easy a center click has been provided which you ll feel snap into place when the indicator points to 12 00 In addition the fre quency control knobs are equipped with twenty four stepped positions so that you can easily return to a desired setting BECOMING FAMILIAR WITH FREQUENCIES Most people intuitively understand boosting and cutting bass mid or treble But how do all these frequencies relate to what you think of as bass or treble Try this on each of the three controls a Raise the level control close to 15 b Play one note repeatedly open A is a good choice c Rotate the frequency control slowly from one end to the other On each band you should notice an audible like of like a wah wah pedal opening up Each of the three bands will accentuate a different range of frequencies and you can begin to correlate numbers with certain sounds Chances are that with each sec
27. n amplifier s Minimum Impedance Rating If you try and operate a power amp below its minimum imped ance rating it will give you lots and lots of power for about five minutes and then overheat short out and fail completely In other words THE LOWER THE OPERATING IMPEDANCE OF THE AMPLIFIER THE HOTTER IT WILL GET BABY BABY BLUE POWER AMPLIFIER MINIMUM IMPEDANCE RATINGS Here s what this means to the power amp in the Baby Baby Blue Being a combo amp it comes equipped with its own internal speaker complement The operating impedance of the internal speaker system in your Baby Baby Blue is 8 ohms The Minimum Impedance Rating of the Baby Baby Blue s power amp is 4 ohms In terms of adding extension speakers this means that you can safely connect One 8 ohm speaker enclosure total impedance 4 ohms Two 16 ohm speaker enclosures total impedance 4 ohms Damage to the power amplifier section of the Baby Baby Blue may occur if speaker enclosures with total impedances less than the minimum loads listed above are connected to the extension speaker output jack The owner s manual that came with your desired extension speaker cabinet should state its total impedance On SWR speaker enclosures the total impedance is generally indicated on the speaker s input panel To figure out the total impedance of two or more cabinets of equal value hooked up in parallel divide the impedance of one cabinet by the number of cabinet
28. of the line tone shaping circuitry an elaborate system that allows you to choose three separate frequency center points and cut and boost them at a level of detail scarcely found on small combos on the market today They have the ability to a correct dead and hot spots that may be inherent in your instrument b correct the effects of poor room acoustics on your bass sound c bring life to old strings d correct peaks or dips in speaker systems and best of all e bring out the best sonic qualities of your instrument and your playing technique At first glance the number of controls and variables may seem fairly complicated But once you get acquainted with how to use and apply the three bands of EQ the possibilities for tone shaping are practically limitless WHAT DOES SEMI PARAMETRIC MEAN In this case the term semi parametric means that each EQ control contains two functions a A level boost cut function b A frequency select function A semi parametric EQ has the advantage of allowing you to select which frequency is cut or boosted by the level control A regular EQ as found on most amps has fixed center frequencies which cannot be altered by the user For the record a fully parametric EQ contains three functions the two listed above plus a band width or Q control USING THE SEMI PARAMETRIC EQ CONTROLS On each band of the semi parametric EQ there are two concentric knobs The inner knob is the LEVEL co
29. ree position slide switch allows you to choose the mode of operation for the piezo tweeter FULL will provide the full range unattenuated signal through the tweeter will bring the tweeter level down slightly and OFF will defeat the tweeter completely Note f the Speaker On Off Switch is set to Off the tweeter will be defeated along with the speak er and therefore the tweeter switch will have no effect INTERNAL FEATURE VACUUM TUBE VALVE SWR installs a specially selected 12AX7A dual triode on the preamp circuitboard of every Baby Baby Blue If this tube needs replacing we recommend that you replace it with a similar high quality product This tube will need replacing only if it becomes noisy or microphonic which sounds like glass tinkling in the background of certain notes or completely fails causing no signal or signal at very low levels The tube in your Baby Baby Blue should last one to three years depending on usage A FEW WORDS CONCERNING HEAT One of the most asked questions about our amplifiers is why they tend to get warmer than other amps The chassis of your amplifier can get quite warm during normal usage This is especially true if you are operating your Baby Baby Blue at a 4 ohm total impedance This is because these low impedances are introducing the least efficient condition of the unit in terms of power drawn from the outlet in relation to power produced in the speakers The difference in these two fig
30. rols EQ Most significantly for basses the Aural Enhancer will help bring out the fundamentals of your lower regis ters without masking them with overtones as is possible when boosting the bass frequencies only At the same time it opens up the sibilance characteristics of all instruments without being harsh Obviously numbers and curves and circuits all mean nothing compared to what you hear with your own ears Play achord a repeated lick or a harmonic and turn the Aural Enhancer control to various points on the knob to hear the effect for yourself As always your ears are the best judge when it comes to settings that affect the tone of your instrument BABY BABY BLUE OWNER S MANUAL 5 EQ DEFEAT SWITCH Located on the Aural Enhancer Control knob this feature gives you the ability to easily defeat whatever EQ settings you have dialed in on the semi parametric active tone controls of your Baby Baby Blue To activate the feature simply pull out on the Aural Enhancer knob until you hear a click Push the control back in to re activate the EQ circuitry This simple feature can be very useful in studio situations imagine the engi neer telling you OK let s hear your EQ Now let s hear it without it or for your own A B test in ana lyzing how you have set your tone controls in comparison to a flat response THREE BAND SEMI PARAMETRIC EQUALIZER A BASIC PRIMER The EQ section of the Baby Baby Blue is our top
31. s Impedance of one cabinet number of cabinets total impedance For an even more in depth discussion of impedance and power rating issues go to the SWR Website at www swrsound com click on Press then click on Articles then click on Plug and Play Setup Tips for Amps and Speakers an article by SWR founder Steve Rabe that ran in the August 92 issue of Bass Player Magazine BABY BABY BLUE OWNER S MANUAL 3 BABY BABY BLUE POWER DELIVERY CAPABILITIES POWER RATINGS After determining how the extension speaker you wish to run affects the total operating impedance you need to take into account the power handling capabilities of that speaker cabinets as compared to what the Baby Baby Blue can deliver at that impedance Those ratings are as follows 120 Watts 8 ohms internal speaker system 160 Watts 4 ohms So for example if you use one 8 ohm extension speaker cabinet the power amp will deliver a total of 160 watts into both the internal and extension speaker 80 watts a piece evenly split It s unlikely that an extension speaker would not be able to handle 80 watts of power and the power rating of the internal speaker is 175 watts so overpowering drivers should not be much of an issue However there is the situ ation known as underpowering your speaker cabinets This is caused when the power amp in the process of trying to drive one or more speaker cabinets reaches its limit and goes into clipping That
32. signal sent from your instrument with the signal coming from an external effects unit With the Effects Blend fully counter clockwise DRY no signal from your external effects unit will be heard As you turn this control clockwise more of the effect can be heard in the overall sound When the Effects Blend control is set fully clockwise WET no true or unaffected signal is heard other than what your external effects unit provides If your external effects unit has a similar control adjust it to the fully clockwise WET position This will avoid any possible phasing problems The Effects Blend circuit is similar to that used on recording consoles with the effects loop on a side chain to the normal circuit Unless the control is set to the full wet position you will always get the full sound of your instrument AND get the diversity an effects unit offers This circuit is also effective in reduc ing noise generated by effects units because it is located after the gain stages in the preamp The Effects Blend control functions only when the Effects Loop is being used It is activated when a 1 4 phone plug is inserted into the Effects Receive jack for more information please see the heading titled Effects Loop in the Rear Panel Features section later in this manual EFFECTS BYPASS SWITCH Located on the Effects Blend Control knob this feature gives you the ability to easily defeat whatever sig nal you ha
33. tion you ll find a couple of positions that are either pleas ing or unpleasing to your ear As you notice this adjust the level control of that band to the desired amount of cut or boost After finding a position on each control activate the EQ DEFEAT switch located on the Aural Enhancer 6 BABY BABY BLUE OWNER S MANUAL Control Knob to compare The more you do this the more you should be able to relate frequency num bers to their respective sounds As you find different settings that you like you may want to write them down somewhere Here s a quick guide that will help you get off the ground in finding a certain kind of sound with the semi EQ SOLUTION Boost the 40 60Hz range Cut the 600 1000Hz range Cut the 1 5k to 2 5kHz range Boost around 200Hz Boost from 5kHz to 7 5kHz Cut the 5KHz to 7 5KHz range Cut 800Hz boost 40 amp 6kHz parametric EQ controls PROBLEM Not enough solid low end Midrange is honky or hollow sounding Treble is harsh and hurts the ear Having trouble cutting through the band Not enough presence lackluster Too much pick or finger noise Need a more dynamic piano sound Try a few of the above examples Then try doing just the opposite just to hear both ends of the spectrum to what s a good sound your own ears Experimentation is five Aural Enhancer EQ settings we dialed in at the factory As always there s only one final judge as encouraged SUGGESTED
34. ubmixer for two instruments but no harm will come from having two instruments plugged in at once Please read below for more details PASSIVE ACTIVE INPUT JACK This input jack is designed to accommodate both passive instruments and most active instruments A passive instrument has no built in preamp and does not use a battery while an active bass utilizes a bat tery operated preamp for gain tone controls or both The Passive Active Input will work with all instru ments having a maximum output of less than 1 volt RMS Some active pickups such as EMG Bartolini etc use batteries for operation and will work perfectly using this input Instruments made by MTD Sadowsky Modulus etc have active electronics that are suited for use in the Passive Active input Generally speaking try this input first If you hear a small amount of distortion and the preamp clip LED is not activated try using the Active input jack If the Active input does not correct any audible distortion check the battery in your bass Note f you would like to overdrive the first TUBE stage this can be accomplished by using an exter nal preamp between your instrument and the Passive Active input To obtain optimum sound when try ing this make sure the preamp clip LED is not activated If this occurs turn down your Gain control until the LED does not light The first preamp tube stage is NOT monitored by the preamp clip circuit for this reason ACTIVE I
35. ug must be a mono plug tip and ground If you have a stereo plug only it will be necessary to tie the ring and the ground together HEADPHONES JACK STEREO ONLY By inserting a set of stereo headphones into this jack you can monitor your sound more closely in a studio situation or practice silently in conjunction with the Speaker On Off Switch on the back panel so as not to completely annoy your neighbors The headphone volume level is adjusted by the Master Volume We suggest you begin with the Master Volume full off counter clockwise then slowly bring up the volume to the desired level If you hear some distortion in your headphones that isn t present through your speaker system turn down the Master Volume You are probably overdriving your headphones and could ruin them to say nothing of what you may be doing to your ears Any impedance headphones will work However optimum impedance is 75 ohms USING EXTENSION SPEAKERS WITH YOUR BABY BABY BLUE This section of the manual will deal with the proper connection of extension speaker cabinets to your Baby Baby Blue so feel free to skip this section if you only plan on only using the unit as a stand alone combo But if you re interested this section will provide information in great detail about power amplifiers imped ance and speaker cabinets as they are all crucial in determining how best to operate your new Baby Baby Blue with extension speakers 12 BABY BABY BLUE OWNER S
36. ull left or full right to avoid an intermittent condition XLR PAD CONTROL This control sets the level present at the Balanced XLR Output Turning the control counter clockwise reduces the overall level while turning the control clockwise boosts the overall level It should be noted that turning the control fully counter clockwise to MIN does not fully defeat the signal This is normal as the XLR Pad is designed to provide a range of usable levels to be sent to a front of house or studio mixing console 10 BABY BABY BLUE OWNER S MANUAL XLR GROUND LIFT SWITCH Sometimes connecting to certain mixing boards or studio consoles with non standard XLR wiring can cause a ground loop Your Baby Baby Blue has a switch located on the XLR Pad Control knob for lifting the ground on the Balanced XLR Output It affects no other outputs Pulling the knob out or pushing it back in will change the mode of operation When the knob is in the in position default setting from the factory ground is on Pin 1 of the Balanced Output jack as normal When the knob is pulled to the out position the ground is lifted from Pin 1 of this output If a persistent hum exists after trying both positions of the ground lift there is probably 1 A bad cable or connection somewhere between your Balanced Output jack and the snake leading to the mixing console 2 A dirty or miswired A C socket 3 Mis wired or poorly wired A C in the building 4
37. ures can be as high as 300 watts This BABY BABY BLUE OWNER S MANUAL 5 would be the equivalent of putting light bulb inside metal box which would obviously get quite hot Most musical instrument amplifiers on the market today use steel for their chassis which does not con duct heat as well as aluminum The Baby Baby Blue uses an all aluminum chassis and because it has less impurities than steel is less susceptible to rust and is a better conductor of heat This results in the chassis acting as an additional heatsink drawing heat away from heat producing components inside and thus extending their life In this manner we feel we have produced a more reliable amplifier but at the same time the outside of the Baby Baby Blue will get warmer than cases made out of steel The one condition you should be aware of is if the power amplifiers in your unit becomes over biased This condition can be recognized by turning your amplifier on and letting it sit idle without playing it If your unit starts getting hot under these conditions it may be over biased This situation should be attend ed to and can be easily remedied in about 15 minutes by a qualified service technician A power amp can become over biased through continuous vibration or by any large jolt received in shipping etc FINAL ENGINEERING SUMMARY The two preamp gain stages utilize a specially selected 12AX7A The tone controls incorporate 1 5
38. ve blended into the Baby Baby Blue s effects loop from an external effects device To activate the feature simply pull out on the Effects Blend Control knob until you hear a click Push the control back in to return the external effects to your signal This feature will function regardless of the position of the Effects Blend control Note f you re wondering why you can t get any signal from your external effects unit even though you have it blended in on the Effects Blend Control check the position of this control and make sure it s in as opposed to out MASTER VOLUME CONTROL The Master Volume control adjusts the level being sent to the power amplifier in your Baby Baby Blue it controls the overall volume of the unit Turning the control counter clockwise reduces the overall level while turning the control clockwise boosts the overall level Two notes The Master control never affects the level present at the various audio output jacks on the BABY BABY BLUE OWNER S MANUAL 9 rear panel it only affects the level being sent to the power amplifier and subsequently your internal speaker and extension speaker output only Also losses caused by external effects units can be recov ered by increasing the Master control POWER AMP CLIP LED The power amp clip LED will illuminate when the internal power amp reaches clipping meaning it has run out of headroom If this LED lights more than occasionally the
39. ypo No it s not It s a smaller more compact version of one of the most sought after pieces ever produced by SWR the Baby Blue Combo This combo amp developed by SWR in the early 1990s was designed for the discerning professional bassist in need of a superior small bass rig for studio and small venues More specifically it was designed to emulate a studio reference monitor and this was done in two ways First it employed a groundbreaking speaker complement two 8 drivers and one time aligned 5 cone tweeter Second it con tained a hyper tweaked version of the original SWR preamp and power amp circuitry with Superior specs in signal to noise ratio power amp frequency response and of course purity of tone Professional players such as Walter Becker Steely Dan Jimmy Haslip Neil Stubenhaus and many more were key in the final stages of development The final result an industry standard bass combo amp coveted by both electric and upright players and by fervent account of SWR insiders and studio musicians perhaps the best sounding electronics package SWR ever produced Demand for an electronics only version of the Baby Blue spawned sporadic limited runs of the head called the Electric Blue or the Baby Blue Head depending on the time period People kept telling us how incredible the amp sounded with a variety of speaker complements but one thing was consistent they were all small highly portable systems We as
Download Pdf Manuals
Related Search