NMEA2000® DC MONITOR Part Numbers: 3410 USER MANUAL
Contents
1. Purchaser s exclusive remedy and Offshore Systems sole obligation hereunder provided product is returned pursuant to the return requirements below shall be limited to the repair or replacement at Offshore Systems option of any product not meeting the above limited warranty and which is returned to Offshore Systems or if Offshore Systems is unable to deliver a replacement that is free from defects in materials or workmanship Purchaser s payment for such product will be refunded Offshore Systems assumes no liability whatsoever for expenses of removing any defective product or part or for installing the repaired product or part or a replacement therefore or for any loss or damage to equipment in connection with which Offshore Systems products or parts shall be used The foregoing warranties shall not apply with respect to products subjected to negligence misuse misapplication accident damages by circumstances beyond Offshore Systems control to improper installation operation maintenance or storage or to other than normal use or service THE FOREGOING WARRANTIES ARE EXPRESSLY IN LIEU OF AND EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE Statements made by any person including representatives of Offshore Systems which are inconsistent or in conflict with the terms of this Limited Warranty shall not be binding upon Offshore Sy2. the reverse the direction of the current transformer on the DC Power cable e If you are using the 500A Shunt then a wire link needs to be made between Terminal 3 and Terminal 4 If you are using the 1200A Shunt then do NOT install a wire link between Terminal 3 and Terminal 4 If the current shows a charge when discharging or vice versa simply exchange the sense wires on the shunts The Thermocouple is an optional extra and need NOT be installed if not needed CALIBRATING THE DC CURRENT TRANSFORMER Before using the DC Current Transformer for the first time it needs to be calibrated to the 3410 for the best accuracy This is done by ensuring that there is NO current flowing through the centre of the transformer and pressing and holding the small pushbutton down for 5 seconds When the button is released then the unit will be calibrated and the blue LED will remain illuminated for a longer 2 second flash CONFIGURATION The following items can be configured on the 3410 4 1 DEVICE INSTANCE It is possible to install 16 3410 DC Monitors on a NMEA20000 network so they need to each have a unique Device Instance Address The Device Instance of each unit is set by turning the small rotary switch with a small screw driver Valid Device Instances range from 0 through to F 4 2 BATTERY TYPE This can be set to either Flooded Wet Gel AGM or Other The unit is set to flooded as it leaves the factory an
3. 96 Product Information PGN059392 ISO Acknowledge PGN059904 ISO Request PGN060928 ISO Address Claim PGN126208 Command Request Group Electrical and Mechanical Parameter Value Comment Operating Voltage 9 to 40 Volts DC Voltage Power Consumption 30mA Average Operating Load Equivalence Number 1 LEN Reverse Battery Protection Yes Indefinately Load Dump Protection Yes SAE J1113 Size mm 96 x 84 x 35 Weight gr 120 Environmental Parameter Value IEC 60954 Classification Protected Degree of Protection IP40 Operating Temperature 25 C to 50 C Storage Temperature 40 C to 70 C Relative Humidity 93 RH 40 per IEC60945 8 2 Vibration 2 13 2Hz 1mm 13 2 100Hz eG 7m s2 per 60945 8 7 Electromagnetic Emission Conducted and Radiated Emission per IEC 60945 9 Electromagnetic Immunity Conducted Radiated Supply and ESD per IEC 60945 10 Safety Precautions Dangerous Voltage Electromagnetic Radio Frequency per IEC 60945 12 Offshore Systems warrants this product to be free from defects in materials and workmanship for one year from the date of original purchase If within the applicable period any such products shall be proved to Offshore Systems satisfaction to fail to meet the above limited warranty such products shall be repaired or replaced at Offshore Systems option
4. NMEA2000 DC MONITOR Part Numbers 3410 WIS One USER MANUAL Revision 1 00 1 Introduction 1 1 Firmware Revision 1 2 Product Features 2 Installation 2 1 Unpacking the box 2 2 Mounting the unit 2 3 Connecting the NMEA2000 Cable 2 4 Connecting the sensor cables to the WAGO socket 4 3 Calibrating the DC Current Transformer 4 Configuration 4 1 Device Instance 4 2 Battery Type 4 3 Nominal Voltage 4 4 Equalisation 4 5 Temperature Coefficient 4 6 Peukert Exponent 4 7 Charge Efficiency Factor 5 State of Charge Resetting 6 Maintenance 7 Technical Specification 8 Warranty 9 Technical Support 65 INTRODUCTION The Offshore System s NMEA2000 3410 DC Monitor is designed to monitor any DC source including batteries PV Cells or Wind Generators on the NMEA20000 network This unit is designed to operate in a protected marine environment such as an engine room It is very important that it is installed and set up correctly according to this manual Please read and follow the installation and setup instructions carefully to achieve the best results 1 1 FIRMWARE REVISION The information in this manual corresponds to firmware revision 1 00 1 2 PRODUCT FEATURES The NMEA2000 3410 DC Monitor has the following features e Inputs from battery voltage 200 Amp DC Current Transformer 500 Amp 50mV Shunt 1200 Amp 50mV Shunt and Thermocouple e User Settable Device Instance using rotary switches e Heartbeat blue LED con
5. d if it is desired to change it to a different value this can be done with a suitable Offshore Systems Display Unit 4 3 NOMINAL VOLTAGE This is the voltage reported over the NMEA2000 network and can be set to 6 12 24 32 or 42 Volts It comes preset to 12 volts and can be changed to a different value with a suitable Offshore Systems Display Unit 4 4 EQUALISATION Used only for reporting over the NMEA2000 network this comes set to Not Supported It can also be set to Supported with a suitable Offsore Systems Display Unit 4 5 TEMPERATURE COEFICIENT The capacity of a battery can increase with temperature so this coefficient is used to make the state of charge more accurate The coefficient can be set to a value between 0 deg C to 5 deg C using a suitable Offshore Systems Display Unit 4 6 PEUKERT EXPONENT This can be set to a value between 1 0 and 1 5 and controls the state of charge calculation for the best accuracy This can be set using a suitable Offshore Systems Display Unit 4 7 CHARGE EFFICIENCY FACTOR This can be set to a value between 5 and 100 to reflect the charging efficieny of the battery for the best state of charge accuracy This can be set using a suitable Offshore Systems Display Unit 5 STATE OF CHARGE RESETTING The 3410 always calculates the remaining state of charge even when the NMEA2000 network is not powered It resets the state of charge to 100 automatically when the charging current drops belo
6. empt to disassemble the device This device contains no user serviceable parts Connecting the AC monitor must be performed by QUALIFIED ELECTRONICS ENGINEER ONLY The cables from the power source to the external sockets are connected using the 6 x 2way WAGO Cage Clamp terminal block The wire should be stripped for 8mm and then the cage clamp opened with a small screwdriver in the slot above the wire connection Then simply insert the wire into it s connection slot and release the cage clamp by removing the small screw driver This will produce a secure gas tight connection on wire sizes from 0 08 2 5 mm 2 J la 6 8 10 12 The terminal connections are numbered as follows 2 4 6 8 10 12 Terminal 1 Battery Negative Must be installed Terminal 2 Battery Positive Must be installed Terminal 3 Current Transformer Black Wire Terminal 4 Current Transformer Green Wire Terminal 5 Current Transformer White Wire Terminal 6 Current Transformer Red Wire Terminal 7 Shunt Negative Terminal 8 Shunt Positive Terminal 9 Thermocouple White Wire Terminal 10 Thermocouple Green Wire Terminal 11 No Connection Terminal 12 No Connection Please note the following important notes If you are using the 200A DC Current Transformer then do NOT install a current shunt as well e If the DC Current Transformer shows a charge when discharging or vice versa
7. firming NMEA transmission e NMEA2000 micro C interface plug e Panel or DIN rail mounting option The unit reports DC Voltage DC Current Battery temperature if optional thermocouple installed and state of charge It uses Peukart s Constant and the Charge Efficiency Factor for the battery to ensure the most accurate state of charge reporting INSTALLATION 2 1 UNPACKING THE BOX You will find the following items in the 3410 shipping box 1 x 3410 NMEA2000 DC Monitor 1 x 3410 User Manual This document 2 2 MOUNTING THE UNIT The unit should be mounted to a flat surface using 4 mounting screws The unit dimensions and mounting hole locations are shown on the following drawing 96 80 Note Mount away from sources of condensation and moisture 2 3 CONNECTING THE NMEA2000 CABLE The unit is connected to the NMEA2000 network by the 5 way micro C socket on the front Carefully attach the network drop cable to this plug and hand tighten until it it is fully seated Take care to match the orientation of the pip inside the socket to the recess inside the drop cable plug The other end of the drop cable should be connected to a suitable Tee connector on the NMEA2000 network backbone cable 2 4 CONNECTING THE SENSOR CABLES TO THE WAGO SOCKET WARNING Risk of Electric Shock This device contains potentially hazardous voltages Ensure that power is removed from all AC circuit that will be connected to the AC monitor Do not att
8. ore Systems UK Ltd All rights reserved Our policy is one of continuous product improvement so product specifications are subject to change without notice Offshore Systems products are designed to be accurate and reliable Howeve they should be used only as aids to vessel monitoring and not as a replacement for traditional navigation and vessel monitorirg techniques 20009 is a registered trademark of the National Marine Electronic Association aj8uis e uo ue Japuas jo d yea 91 quan 2v dWV 002 ETHE ww0007 0SZ Japuas Je eM use14 1876 ww0007 0SZ AI 1875 i 0007 057 je 1822 YUL aAnstsed 20 2 3 0 Jeuuojsue1 uen 5d um junys 2 SE 000 062 leng MZE PS SOLE soydepy 459 YJ 013108 S JYS eze a i 51032auuo ajqemexsu pied aIeW 9082 GOBE B 0 eqe MNA 078 10 4031U0W OV 443 33 ainpow andu WDUMS e di mem soydepy 1 2082 away 2086 S1939W 0l B G Z L S O S38spJ02 OIW 6L8E OL8E fal N j pela an N n seBneo JejsueJ OSEE Kejdsiq uono 6J pue Obal VOX OLLE VOAM 0 xpelg useJ4 Jang saBney jas HUEL OSEE Aeydsig uono
9. stems unless reduced to writing and approved by an officer of Offshore Systems IN NO CASE WILL OFFSHORE SYSTEMS BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES DAMAGES FOR LOSS OF USE LOSS OF ANTICIPATED PROFITS OR SAVINGS OR ANY OTHER LOSS INCURRED BECAUSE OF INTERRUPTION OF SERVICE IN NO EVENT SHALL OFFSHORE SYSTEMS AGGREGATE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT S INVOLVED OFFSHORE SYSTEMS SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHETHER ARISING OUT OF BREACH OF CONTRACT OR WARRANTY TORT INCLUDING NEGLIGENCE OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY OFFSHORE SYSTEMS OR ANY UNDERTAKINGS ACTS OR OMISSIONS RELATING THERETO Offshore Systems does not warrant that the functions contained in any software programs or products will meet purchaser s requirements or that the operation of the software programs or products will be uninterrupted or error free Purchaser assumes responsibility for the selection of the software programs or products to achieve the intended results and for the installation use and results obtained from said programs or products No specifications samples descriptions or illustrations provided by Offshore Systems to Purchaser whether directly in trade literature brochures or other documentation shall be construed as warranties of any kind and any failure to conform to such specifications samples descriptions or illustrations shall not constitu
10. te any breach of Offshore Systems limited warranty WARRANTY RETURN PROCEDURE To apply for warranty claims contact Offshore Systems or one of its dealers to describe the problem and determine the appropriate course of action If a return is necessary place the product in its original packaging together with proof of purchase and send to an Authorized Offshore Systems Service Location You are responsible for all shipping and insurance charges Offshore Systems will return the replaced or repaired product with all shipping and handling prepaid except for requests requiring expedited shipping i e overnight shipments Failure to follow this warranty return procedure could result in the product s warranty becoming null and void Offshore Systems reserves the right to modify or replace at its sole discretion without prior notification the warranty listed above g TECHNICAL SUPPORT If you require technical support for any Offshore Systems products you can reach us using any of the following ways e Tel 44 0 1425 610022 e Fax 44 0 1425 614794 e Email support osukl com e Web www osukl com e Post Offshore Systems UK Ltd Unit 10 11 Milton Business Centre Wick Drive New Milton Hampshire BH25 6RH Offshore Systems UK Ltd Unit 10 11 Milton Business Centre Wick Drive New Milton Hampshire BH25 6RH United Kingdom Tel 44 0 1425 610022 Fax 44 0 1425 614794 Email sales osukl com Web www osukl com Copyright O 2013 Offsh
11. und MNW SPEE 2 2d Ole doydepy 3nw POBE pesa peatpnng 2086 Josuas aunqesadway wooy aujBu3 Sek aqoig pinbr1 czcr andino g pc Josuas sty uqe ZZS Josuas seg OLG paa ZEBE avaHying apoy aunyesadway jeuueu5 y 09 uoneuuoju 3usuisBeuew ouiBu3 seumpejnuew Jozdepy Jo depv S8L Jam JOyeunuua Brew rose lt yP07 Jans LZE snqpow Scie neo Jena xped OLE SW3 SAS TOULNOD ANY DONIMOLINOW T3SS3A e0002V3WN dVW LONGOYd SWALSAS JYOHSIAO
12. w a threshold whilst the charging voltage is above a threshold for a predetermined period of time The unit can also be forced to the 100 value by pressing the small button next to the Device Instance switch for 1 second MAINTENANCE Clean the unit with a soft cloth Do not use chemical cleaners as they may remove paint or markings or may corrode the enclosure or seals e Ensure that the unit is mounted securely and cannot be moved relative to the mounting surface If the unit is loose tighten the mounting screws Check the security of the cables connected to the NMEA 2000 connector tighten if necessary e Check the security of the cables connected to the WAGO terminal block reseating them if necessary TECHNICAL SPECIFICATION As Offshore Systems are constantly improving their products specifications are subject to change without notice Offshore System s products are designed to be accurate and reliable however they should only be used as aids to navigation and not as a replacement for traditional navigation aids and techniques Certifications Parameter Comment NMEA2000 Level B Maritime Nav and RadioComm Equipment IEC60945 CE and FCC Electromagnetic Compatibility NMEA2000 Parameter Group Numbers PGNs Type PGN No PGN Name Monitor PGN127506 DC Detailed Status PGN127508 Battery Status PGN127513 Battery Configuration Status Protocol PGN126464 Tx Rx List PGN1269
Download Pdf Manuals
Related Search