DJ Lase Polar 200 showlaser user manual
Contents
1. the instructions given here amp Chapter 2 Safety instructions on page 8 Any servicing of the unit with open housing must only be carried out by quali fied technicians For working on the device you have to wear suitable laser safety goggles In the following we list a few common problems that may occur during operation We give you some suggestions for easy troubleshooting th mann MUSIC IS OUR PASSION 37 Symptom Remedy The unit does not work no light the fan does 1 Check the mains power connection and the main fuse not run 2 Check the safety key switch No response to DMX controller 1 If the display indicates a flashing figure e g 001 no DMX signal is received Check the DMX connections and cables for proper connection 2 If the display is not flashing and the unit does not respond check the address settings and the DMX polarity 3 Try to use another DMX controller 4 Check to see if the DMX cables run near or alongside to high voltage cables that may cause damage or interference to DMX interface circuits If the procedures recommended above do not succeed please contact our Service Center You can find the contact information at www thomann de showlaser 38 Cleaning 9 Cleaning DANGER Laser radiation During cleaning you have to follow the instructions given here amp Chapter 2 Safety instructions on page 8 To avoid unintended laser radiation remove the safe2. S TeV DJ Lase Polar 200 showlaser th mann user manual MUSIC IS OUR PASSION Musikhaus Thomann Thomann GmbH Hans Thomann Stra e 1 96138 Burgebrach Germany Telephone 49 0 9546 9223 0 E mail info thomann de Internet www thomann de 14 08 2015 ID 278697 Table of contents na vu BF WN 10 Table of contents General OCS isis sii caieisscatiasicii sdsaidscdacas cdiscacsdapiatanteccvssdwacaiacataasttvoancsinadinidasansanndaieaateastadaoancsaardaaananie 5 Safety iNstructiOns eecsscssssssssecssecsssecssscessscessseecssecssscceseesssecsssesssscessscesacesseeceuseesseeceseessueeesseessees 8 Features sssisccssiecscsssciasiesscsssdiatiedscasscossceseviesssusiedovtodesdbodaviess abodes ae Ra aa aa seen tastes 15 Installation E EAE Starting UP Components and function Operation 7 1 7 2 7 3 7 4 Starting and stopping the device Main Men en neh Ei aaa aia Menu overview Functions in DMX mode Troubleshooting teas ouloiscsasccbdedlendecbusdcayagaiunddivbeutssussccadesdacnend 37 GMS UMN Gy A E E A A E 39 Technical specifications cccccsssssssssssssssssssecsessesssssssssssessesssscsscsssessucssscsnecssesscssscsssesscsssesssesses 40 th mann MUSIC IS OUR PASSION Table of contents 11 Protecting the environment ec ssssssessssseeesssesssssecesseessnseessnseeessnecessnecesseesssseessnseeesuneeesuees 42 th mann M
3. USIC IS OUR PASSION 1 General notes Symbols and signal words General notes This user manual contains important information on safe operation of the device Read and follow all safety notes and all instructions Save this manual for future reference Make sure that it is available to all persons using this device If you sell the device include the manual for the next owner Our products are subject to a process of continuous development We therefore reserve the right to make changes without notice This section provides an overview of the symbols and signal words used in this user manual th mann MUSIC IS OUR PASSION General notes Signal word DANGER WARNING NOTICE Warning signs A A th mann MUSIC IS OUR PASSION This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a pos sible dangerous situation that can result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a pos sible dangerous situation that can result in material and environmental damage if it is not avoided Type of danger Warning high voltage Warning laser radiation General notes Warning suspended load N Warning danger zone th mann MUSIC IS OUR PASSION Safety instructions 2 Safety instructio
4. aser beam The laser beam can injure your eyes when you directly look into it Do not expose yourself to the laser beam The laser beam can cause skin burns In this context take extreme care when using converging optical instruments th mann MUSIC IS OUR PASSION 11 Safety instructions WARNING Eye damage caused by high light intensity Never look directly into the light source WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy Sensitive persons should avoid looking at strobe lights NOTICE Laser radiation risk of fire o Keep the area exposed to laser radiation free from flammable substances th mann MUSIC IS OUR PASSION 12 Safety instructions NOTICE Risk of fire Do not cover the device nor any ventilation slots Do not place the device near any direct heat source Keep the device away from naked flames NOTICE Operating conditions This device has been designed for indoor use only To prevent damage never expose the device to any liquid or moisture Avoid direct sunlight heavy dirt and strong vibrations th mann MUSIC IS OUR PASSION 13 Safety instructions NOTICE Power supply Before connecting the device ensure that the input voltage AC outlet matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker Failure to do so could result in damage to the device a
5. e from the power supply 9 Press FUNC to activate the main menu and select one of the operation modes Wenn die Anzeige blinkt benutzen Sie die Tasten UP und DOWN um den jeweils ange zeigten Wert zu ndern Wenn das Display den gew nschten Wert anzeigt dr cken Sie ENTER Um ohne nderungen zur ck in das Hauptmen zu kommen dr cken Sie FUNC oder warten Sie eine Minute Alle zuvor vorgenommenen Einstellungen werden gespeichert auch wenn Sie das Ger t vom Stromnetz trennen th mann MUSIC IS OUR PASSION 29 Operation Operating mode Auto Show Press FUNC repeatedly until the display shows Arf or Sr xa and starts flashing The device A r H operates in stand alone mode and displays a preprogrammed show ArA provides a show tion in Auto Show mode SrA Operating mode Sound con trolled and adjusting the response characteristic with fast effects SrA provides slow effects Press ENTER to save the value and to start opera Press FUNC repeatedly until the display shows 5 a u and starts flashing The device operates 5 ow in stand alone mode and displays a sound controlled preprogrammed show In this menu you can adjust the sensitivity and thus the response characteristic of the microphone Press ENTER to save the setting Now the display shows 5 5 Use the UP and DOWN buttons to select the settings S 0 s
6. en sitivity 0 operation mode Sound controlled is off or S 1 low sensitivity to S 9 high sensi tivity Press ENTER to save the setting th mann MUSIC IS OUR PASSION 30 Operating mode Manual neo Press FUNC repeatedly until the display shows nAn Press ENTER to confirm Hala In this mode you can set the laser diode and the LED for the backlight illumination manually The following table shows the possible settings Display Description RO R9 Red laser flash frequency fast to slow G0 G9 Green laser flash frequency fast to slow M10 M19 Laser dot movement slow to fast M20 M29 Blue LED backlight illumination movement slow to fast Lb0 Lb9 Blue LED backlight illumination brightness LFO LF9 oes LED backlight illumination flash frequency fast to slow DJ Lase Polar 200 31 Operation Operating mode DMX Press FUNC repeatedly until the display shows 29 1 Now you can adjust the number of the l first DMX channel DMX address used by the unit Select a value between 1 and 511 using the UP and DOWN Press ENTER to store the value and to start operation in DMX mode Make sure that this number corresponds with the configuration of your DMX controller Operating mode Master Slave Press FUNC repeatedly until the display shows 51 A In this operation mode the unit follows D L H exactly the master device tha
7. nd possibly injure the user Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire th mann MUSIC IS OUR PASSION 14 Features 3 Features This showlaser is specially suited for discos clubs bars small stages etc and can be easily inte grated in light shows or operated in stand alone mode The two laser diodes together with the LED background illumination and the rotatable diffusing panel provide extraordinary spe cial effects Special features of this device Control via DMX 6 channels and via buttons and display on the unit Preprogrammed automatic shows Sound control Master slave mode Laser diodes Red 100 mW Green 40 mW Blue LED background illumination Projection lens and diffusing panel for laser and background illumination th mann MUSIC IS OUR PASSION 15 Installation 4 Installation th mann MUSIC IS OUR PASSION Unpack and carefully check that there is no transportation damage before using the unit Keep the equipment packaging To fully protect the device against vibration dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage respectively You can install the device on the wall ceiling or floor Amounting bracket and the necessary screws are included in the package DANGER Laser radiati
8. nd notify the operation of the laser equipment to the Accident Pre vention and Insurance Association and to the authority responsible for occupational safety In the event of public use the complete laser equipment must be approved by an expert e g the Technical Control Board TUV prior to commissioning th mann MUSIC IS OUR PASSION Safety instructions Safety DANGER Danger for children Ensure that plastic bags packaging etc are disposed of properly and are not within reach of babies and young children Choking hazard Ensure that children do not detach any small parts e g knobs or the like from the unit They could swallow the pieces and choke Never let children unattended use electrical devices DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Never remove any covers There are no user serviceable parts inside th mann MUSIC IS OUR PASSION 10 Safety instructions DANGER Electric shock caused by short circuit Always use proper ready made insulated mains cabling power cord with a pro tective contact plug Do not modify the mains cable or the plug Failure to do so could result in electric shock death or fire If in doubt seek advice from a regis tered electrician DANGER Laser radiation avoid exposure to beam The device contains a class 3B laser classified according to EN 60825 1 Do not look into the l
9. nn 25 26 OUTPUT DMX output INPUT DMX input Display MIC Microphone for operating mode Sound controlled Safety eye SAFETY Safety key switch to turn the laser output on or off IEC chassis connector for the mains cable Next to it the proper operating voltage is indicated POWER Mains switch to turn the unit on or off showlaser Components and functions th mann MUSIC IS OUR PASSION 27 Operation 7 Operation 7 1 Starting and stopping the device Starting Carry out the following steps to take the unit into operation Check to see whether all laser safety precautions have been taken Make sure that nobody is in range of the laser beam Insert the safety key into the lock 8 If not already done connect the device to a mains power outlet 9 ree Turn the unit on using the main switch 10 After a few seconds the fan and the motors start to work The display shows the current operating mode The unit is now opera tional Turn the safety key 8 into the ON position to turn the laser beam on 5 th mann MUSIC IS OUR PASSION 28 Stopping 7 2 Main menu Operation Carry out the following steps to stop the unit 1 _ Turn the safety key 8 into the OFF position to turn the laser beam off and pull the key off Keep the safety key in a safe place 2 Turn the unit off using the main switch 10 3 Additionally you can disconnect the devic
10. ns Intended use This device is intended to be used for the projection of laser light effects It has been designed exclusively for show applications Use the device only as described in this user manual Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage No liability will be assumed for damages resulting from improper use This device may be used only by persons with sufficient physical sensorial and intellectual abilities and having corresponding knowledge and experience Other persons may use this device only ifthey are supervised or instructed by a person who is responsible for their safety th mann MUSIC IS OUR PASSION Laser safety basics Safety instructions Laser safety requirements are based on DIN EN 60825 1 The corresponding accident preven tion regulation of the Accident Prevention and Insurance Association in Germany is BGV B2 This device contains a class 3B laser It is equipped with a safety key Always remove the key when the device is not attended by a trained operator As an operator you are responsible for the safety of all persons present Familiarize yourself with the laser safety regulations that apply in your country To ensure safe operation it is important to pay attention to the following instructions Prior to commissioning the company operator must appoint a qualified person as laser pro tection officer in writing a
11. on During installation you have to follow the instructions given here amp Chapter 2 Safety instructions on page 8 To avoid unintended laser radiation remove the safety switch before you start the installation of the device 16 Installation WARNING Stray laser radiation Inadequately secured additional components may cause stray laser radiation Make sure that all additional components are adequately secured WARNING Risk of injury caused by falling objects Make sure that the installation complies with the standards and rules that apply in your country Always secure the device with a secondary safety attachment such as a safety cable or a safety chain th mann MUSIC IS OUR PASSION 17 Installation NOTICE Risk of overheating o The distance between the light output and the illuminated surface must be more than 0 5 m 19 7 in Always ensure sufficient ventilation The ambient temperature must always be below 40 C 104 F DMX connections The unit offers a 3 pin XLR socket for DMX output and a 3 pin XLR plug for DMX input Please refer to the drawing and table below for the pin assignment of a suitable XLR plug th mann MUSIC IS OUR PASSION 18 Starting up 5 Starting up Establish all connections as long as the unit is switched off Use the shortest possible high quality cables for all connections th mann MUSIC IS OUR PASSION 19 Starting up NOTICE Po
12. rmal household waste but make sure that they are collected for recycling Please follow the notes and markings on the packaging This product is subject to the European Waste Electrical and Electronic Equipment Directive WEEE Do not dispose with your normal household waste Dispose of this device through an approved waste disposal firm or through your local waste facility When discarding the device comply with the rules and regulations that apply in your country If in doubt consult your local waste disposal facility 42 Musikhaus Thomann Hans Thomann Stra e 1 96138 Burgebrach Germany www thomann de
13. ssible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX input or output to audio devices such as mixers or ampli fiers th mann MUSIC IS OUR PASSION 20 Starting up Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device Connect the output of the first DMX device to the input of the second one and so on to form a daisy chain Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor 1100 1 4 W th mann MUSIC IS OUR PASSION 21 Starting up Connections in master slave mode th mann MUSIC IS OUR PASSION When you configure a group of devices in master slave mode the first unit will control the other units for an automatic sound activated synchronized show This function is ideal when you want to start a show immediately Connect the DMX output of the master device to the DMX input of the first slave device Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on 22 Components and functions 6 Components and functions Vorderseite th mann 23 Components and functions themann MUSIC IS OUR PASSION 24 Components and functions Rear panel a A WARNING THIS APPLIANCE MUST BE EARTHED Be J i th ma
14. t it is connected to Press ENTER to confirm and to start opera tion in Master Slave mode th mann MUSIC IS OUR PASSION 32 Operation lew 3 Menu overvi 7 MUSIC IS OUR PASSION Cc R 5 33 7 4 Functions in DMX mode Channel Value Function 1 Operating mode selection 0 51 Laser off 52 102 Automatic show in random order fast 103 154 Automatic show in random order slow 155 206 Sound controlled automatic show in random order 207 255 Operating mode DMX this setting activates the function of the other DMX channels 2 Red laser 0 4 Laser off 5127 Laser is constantly on 128 254 Strobe effect flashing decreasing speed showlaser 34 Channel Value Function 255 Sound controlled strobe effect flashing Green laser 0 4 Laser off 5 127 Laser is constantly on 128 254 Strobe effect flashing decreasing speed 255 Sound controlled strobe effect flashing Rotation ofthe red and green laser around the Z axis rolling 0 4 No rotation 5 127 Rotation effect clockwise increasing speed 128 133 No rotation 134 255 Rotation effect counter clockwise increasing speed Intensity ofthe blue LED background illumination 0 4 Background illumination off DJ Lase Polar 200 35 Operation th mann 36 Troubleshooting 8 Troubleshooting DANGER A Laser radiation inside the housing During troubleshooting you have to comply with
15. ty switch before you begin to clean the device Optical lenses Clean the exterior of accessible optical lenses periodically to optimise light output The fre quency of cleaning depends on the operating environment wet smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device Clean with a soft cloth using normal glass cleaning products Always dry the parts carefully th mann MUSIC IS OUR PASSION 39 10 Technical specifications Laser medium Laser power Laser classification acc to EN 60825 1 2007 Beam diameter at outlet aperture Pulses Divergence per beam Divergence overall light LED background illumination Number of DMX channels Operating voltage supply 40 Red 650 nm typical LD GaAlAs Green 532 nm typical DPSS Nd YV04 Red 100 mW Green 40 mW 3B lt 5mm All pulses lt 4 Hz gt 0 25 s lt 2 mrad lt 160 Blue 5 W 7 AC 100 240 V 50 60 Hz showlaser Technical specifications th mann 41 Protecting the environment 11 Protecting the environment Disposal of the packaging mate rial Disposal of your old device th mann MUSIC IS OUR PASSION For the transport and protective packaging environmentally friendly materials have been chosen that can be supplied to normal recycling Ensure that plastic bags packaging etc are properly disposed of Do not just dispose of these materials with your no
Download Pdf Manuals
Related Search