dl405 dimension installation
Contents
1. An expansion cable is required to connect each of the expansion bases to the CPU base D4 EXCBL 3 08 ft 1m cable lt gt D4 EXCBL 2 1 54 ft 0 5m cable lt gt D4 450 and 1 bases In the past a DL405 system has been limited to only accepting specialty modules in the local CPU base The 1 bases must be used with the D4 450 CPU to remove this limitation The part numbers for the bases are D4 04B 1 D4 06B 1 and D4 08B 1 Note you cannot simply add a 1 base to an existing system to gain specialty modules in expansion bases Instead you must replace the CPU base and all other expansion bases as well You can add the 1 bases in an older system but they are subject to the limitations of the regular bases 4 slot base CPU oam oO oomunn oO CPU Expansion Unit or Remote Slave Slot CPU 8 Slot base Expansion Connectors O i CPU Base Expansion Cable 1 6ft 5m 3 3 ft 1m Specialty modules in expansion bases No Must use 04 450 CPU 6 i o Specialty module www automationdirect com dl405 No Both bases must be 4 tyne Doa Specialty module PLC Products Yes Uses D4 450 and 1 bases DB Specialty module 6 29 A S Direct v PLC Overview DL05 06 PLC DL105 PLC DL205 PLC DL305 PLC DL405 PL2. clearance However your distance may be greater or less Also check the installation guidelines for the recommended cabinet clearances a Panel Ground Braid DL405 base p Copper Lugs he A c V Panel or Note there is a minimum of 2 50mm clearance required w Star Washers Single fom between the panel door or any devices mounted in the panel i fa o fa door and the nearest DL405 component 2a 1 4 69 150mm 119mm B o D4 04B 1 10 82 6 a D4 06B 1 13 74 B __ D4 08B 1 16 65 6 28 amp PLC Products 1 800 633 0405 Base Configurations Four six and eight slot bases The DL405 product family offers four six and eight slot I O bases Expansion units The expansion units are only necessary when you want to use local expansion They are installed in the CPU slot of the expansion bases They appear very similar to CPUs but they only contain a power supply One of the most often asked questions for the DL405 family is Does the CPU consume an I O slot The answer is no The CPU has a special slot in the base and does not consume any of the available I O slots The same is true for Expansion Units D4 EX 110 220 VAC power supply lt gt D4 EXDC 24 VDC power supply lt gt D4 EXDC 2 125 VDC power supply lt gt and the Remote Slave Units D4 RS 110 220 VAC power supply lt gt
3. C Field I O Software C more HMIs Other HMI AC Drives Motors Steppers Servos Motor Controls Proximity Sensors Photo Sensors Limit Switches Encoders Pushbuttons Lights Process Relays Timers Comm TB s amp Wiring Power Enclosures Appendix Part Index
4. Dimensions and Installation It is important to understand the installa Ube OK tion requirements for your DL405 system se With 32 pt or 64 pt sol 6 375 This will help ensure that the DL405 prod nee saliar 162mm ucts operate within their environmental 5 5 With 32 pt or 64 pt ribbon 3 and electrical limits j i a e With programming or OI cable DE Dom Plan for safety t Airflow e This catalog should never be used as a replacement for the user manual The user manual D4 USER M contains important safety information that must be followed The system installation should comply with all appropriate electrical codes and stan 4 375 dards With 8 or 16 1 0 111mm Base dimensions and mounting Specification orientation Storage Temperature 4 F 158 F 20 C to 70 C athe di grams t th rightto make sure snblent operaring Temperature 32 F 140 F 0 to 60 C the DL405 system can be installed in your Ambient Humidity 30 95 relative humidity non condensing application To ensure proper airflow for Vibration Resistance MIL STD 810C Method514 2 cooling purposes DL405 bases must be Shock Resistance MIL STD810C Method516 2 mounted horizontally It is important to 5 7 check these dimensions against the condi Kinia UIT MENASSA tions required for your application For Atmosphere No corrosive gases example it is recommended that you leave 1 5 depth for ease of access and cable
Download Pdf Manuals
Related Search