Next-generation High-definition Day & Night Video Camera
Contents
1. DEFECT RS485 RETURN DA DN Bb uy Ne CAMERA TITLE In the camera title menu press the left right to select On At this point the camera image will display the name of executive function Click OK button to enter the CAMERA TITLE setting sub menu you can set the camera name You can set the camera code as numbers uppercase letters and related symbols The length of the names is 15 characters 13 Clear is for removing the camera name Location name for the set position Through the up down left right mobile name location to determine a good location then press OK button to return the name of the Edit menu End is the end of the name edit to return to the previous menu D EFFECT D EFFECT 1 FREEZE ON OFF 2 MIRROR OFF MIRROR V FLIP ROTATE 3 NEG IMAGE OFF ON 4 RETURN RET lt When FREEZE set ON the MIRROR function is not available MOTION In the MOTION menu press the left right to select On At this point the image will open the motion detection Then click OK button to enter the MOTION setting sub menu to set the detect range and sensitivity settings 14 MOTION SELECT AREA 1 2 3 4 DISPLAY ON OFF SENSTIVITY 0 100 COLOR RED GREEN BLUE WHITE IRANS 0 25 0 5 0 75 1 00 ALARM DEFAULT RETURN ALARM can be set under motion mode click OK button to enter the sub menu ALARM VIEW TYPE ALL OFF2. AGC SENS UP BRIGHTNESS D WDR DEFOG RETURN Sens up has the two choices Auto OFF User can select according to the lens equipped correspondingly Choose auto to enter sub menu Sens up can be set between x2 to x30 SENS UP 1 SENS UP 2 RETURN D WDR has three options auto on and off When D WDR on user can choose level between 0 8 1 LEVEL 2 RETURN DEFOG has two options off and auto Choose auto to set 1 POS SIZE 2 GRADATION 3 DEFAULT 4 RETURN 1 3 BACKLIGHT In the Backlight menu press the left right to select BLC 7 OFF HSBLC Users can select the appropriate backlight mode according to the actual needs Under BLC Mode BLC level can set middle low and high BLC MODE 1 LEVEL Middle HIGH LOW 2 AREA 3 DEFAULT 4 RETURN HSBLC Mode there are totally 4 select areas Display can set on and off Black mask can also set on and off HSBLC level is from 0 to 100 HSBLC SELECT AREA 1 2 3 4 DISPLAY ON OFF BLACK MASK ON OFF LEVEL 0 100 MODE ALL DAY NIGHT DEFAULT lt RETURN RET HSBLC mode has two options night and all day On night mode AGC level can be adjusted from 0 to 255 NIGHT MODE 1 AGC LEVEL 0 255 2 RETURN RET lt 1 4 WHITE BAL White Balance is used to restore the authenticity of the scene it is affected by scene color temperature change Users can choose the corresponding white balance mo
3. BLOCK OUTLINE OSD VIEW ON OFF ALARM OUT ON OFF ALARM SIG HIGH LOW TIME RETURN PRIVACY In the PRIVACY menu press the left right to select On 15 At this point the image will open the Privacy masking Then click OK to enter privacy shield setting sub menu you can mask the scope of privacy and sensitivity settings PRIVACY SELECT AREA 1 2 3 4 DISPLAY COLOR OFF MOSAIC INV COLOR WHITE BLACK RED BLUE YELLOW GREEN CYAN USER TRANS 1 00 0 25 0 50 0 75 DEFAULT lt RETURN RET lt LANGUAGE English Chinese CHN1 amp CHN2 German French Italian Spanish Polish Russian Portuguese Dutch Turkish totally twelve language selections DEFECT Chooses this item then presses the OK key to enter sub menu DEFECT 1 LIVE DPC ON OFF 2 WHITE DPC ON OFF 3 BLACK DPC ON OFF 4 RETURN RET lt LIVE DPC ON LIVE DPC 1 AGC LEVEL 2 LEVEL 3 RETURN WHITE DPC ON WHITE DPC POS SIZE lt START lt DPC VIEW OFF ON LEVEL AGC SENS UP x2 4 6 8 10 15 20 25 30 RETURN RET BLACK DPC ON BLACK DPC POS SIZE lt START DPC VIEW OFF ON LEVEL 0 100 RETURN RET RS485 Click OK button to enter the sub menu 1 CAMID 1 255 2 ID DISPLAY OFF ON 3 BANDRATE 2400 4800 4 RETURN RET Please note the RS485 function is not available for the IR cameras 8 ADJUST Click OK button t
4. as usual please do not dismantle it by 2 yourself Please contact our local distributor or our maintenance office authorized by our company otherwise we won t promise warranty gt Please do not splash water on the product components when cleaning Notes gt Do not make the products under great impact or stay away from strong electromagnetic interference and vibration gt There are some sophisticated parts inside the camera therefore during transportation and installation please avoid the damage cause by stress or severe vibration For the sake of safety please do not switch on power before accomplishing all installation gt Please comply with all electrical safety standards during operation camera or signal transmission cable should maintain a sufficient distance 50 meters with high voltage equipment or cables If necessary lighting and thunder protective measures must be taken gt Please install the camera in well ventilated environment gt Please do not make the camera face sunshine or other strong light directly in case of any damage to the lens and the sensor gt The temperature and humidity range for cameras work are 10 50 C less than 95 separately please do not start cameras beyond this range gt To avoid lightning strikes please make sure the installation of power supply ground line in a good condition gt To prevent the equipment from damage by shower or splash of water please do not place t
5. High definition Analog Video Camera Built in OSD USER S MANUAL Applicable for AHD Standard Cameras AHD Dome Cameras AHD Waterproof IR Cameras Thank you for purchasing our products Please read the manual carefully before operating Safety Precaution Warning A Dont dismantle without authority A becareful thunder striking Note To avoid thunder strking please dont open the backcover the maintenance must be made by our authorized serviceman A This symbol means that there might exist uninsulated dangerous voltage inside the case be careful of electric shock A This symbol reminds you to pay attention to important operation and maintenance instructions in the accompanied information Warning gt In order to prevent damage caused by fire or electric shock please do not put cameras exposed in the moist environment or rainwater gt Please make sure the adapter is consistent with product specifications otherwise it might cause fire electric shock or damage gt Pay attention to polarity of the adapter it might cause some accidents like fires gt Please don t connect multiple cameras with the same adapter at the same time overloading of adapter capacity may cause fires gt Power supply must be firmly fixed so as not to loose to cause fires gt If the device gets abnormal smell or smoke please stop it immediately and contact with our customer service center gt Ifthe camera doesn t work
6. MART ON OFF 3 IR PWM 0 100 4 RETURN RET When IR smart on click OK button to enter the sub menu of IR Smart IR SMART 1 LEVEL 0 15 2 AREA lt 3 RETURN RET lt EXT MODE D amp N EXT 1 D N DELAY 2 N D DELAY 3 RETURN Delay for both D gt N and N gt D could be adjusted from 0 to 60 Note Set the D N DELAY and N D DELAY is to prevent the frequent changes in light caused by switching the camera has been 11 in a state of users On the choice of the value do not set to the same value The same value will lead to frequent switch under the light intensity changing 1 6 NR In the NR menu click OK button to enter the sub menu you can set the corresponding parameters Noise reduction is in the case of very low light reduction caused by low light point of the picture noise to enhance the signal to noise ratio S N and image clarity and the camera in low light conditions catches clearly sharpness image the quality can be guaranteed NR 1 2DNR LOW MIDDLE HIGH OFF 2 3DNR LOW MIDDLE HIGH OFF 3 RETURN RET lt Set the noise reduction mode 2DNR 3DNR two options Choose noise reduction corresponds to the modes When the setup complete click OK button to return to the implementation for the appropriate functions 1 7 Special Click OK button to enter the Special setting sub menu 12 SPECIAL CAMTITLE D EFFECT MOTION PRIVACY LANGUAGE
7. connect the power supply correctly whether the indicating led is always on or not b Check the video cable make sure it is workable c Check if the monitor has been open 2 Q Image interference after installation a Check the power quality if the adapter can t work please replace another one b Check if electromagnetic interference exists in the surroundings please use some anti interference devices 3 Q The image color is abnormal a please make sure if the white balance is correctly set as Auto White Balance b Please enter the menu to restore factory settings 4 Q Image appears to be whiter than usual after installation a Please check whether the lens aperture was adjusted too large so that the image appears whiter b Please verify the camera rear panel if the regulator potentiometer is adjusted too large c Check if the brightness of the monitor is too large 5 Q When installation image is not clear or exist dark corners a Please adjust focus and zoom of the lens Make sure the focus should be adjusted in a proper way b Please check if the lens is clean 22
8. de according to the actual needs of the scene They are ATW AWC gt Set Indoor Outdoor Manual AWB In Manual WB mode the Blue and Red color can be adjusted from 0 to 100 MANUAL WB 1 BLUE 2 RED 3 RETURN Note In general users only need to use the auto tracking white balance AWB 1 5 DAY amp NIGHT Day night switching function is mainly for the user to use the camera easily on different occasions There are 4 modes of day night color mode black and white mode EXT mode auto mode Press the left right key to select Auto Mode Click OK to 9 enter Auto Mode sub menu you can set the corresponding parameters AUTO Mode D amp N AUTO D gt N AGC D gt N DELAY ND AGC N gt D DELAY RETURN Delay with this setting the camera achieves the delay time of the transferring color to black white or black white to color Conversion between the colors is through controlling of the camera s brightness sensor of the scene When the light is at critical time the camera may switch the modes back and forth between color and black white Setting the delay time function can resolve this problem When the camera senses the light intensity during this period are in line with the color conversion before the conversion feature or do not perform It is also intended to better protect the camera and allows users to have better image quality 10 B W Mode 1 BURST ON OFF 2 IRS
9. he device substances such as liquid Contents OO A 5 POLENS E A EE 5 EHEXP 0 SWRI re errr A 6 PSB BAC KEIGHT ree tue warren cre rere ee reenter 7 AN SKS E E 9 LEIDA SA SITE 9 NR S O 12 A OA ES 12 NO STS SS AA 18 PEC rre 20 ls Tednteri Sjoeliifeli 01socosoroeovo0s000000069000000050060000090000060S00 21 oro 22 I OSD Press the OK button the camera will pop up the main menu system MAIN MENU 1 LENS MANUAL 2 EXPOSURE 3 BACKLIGHT OFF 4 WHITE BAL ATW 5 DAY amp NIGHT 6 NR 7 SPECIAL 8 ADJUST lt 9 EXIT SAVE amp END 1 1 LENS There are 2 types of lenses respectively DC lens DC drive lens video camera manual lens Users can select the lens type according to the using of the camera Press the left or right button on to choose the lens When select the iris speed should choose DC file users can adjust the speed value to adjust the open speed of iris The value smaller the speed of opening the iris is lower the value bigger the speed is faster DC LENS MODE 1 MODE INDOOR 2 IRIS SPEED 0 15 3 RETURN RET lt Users can choose indoor mode amp outdoor mode accordingly Outdoor Mode OUTDOOR MODE 1 MIN SHU 2 MAX SHU 3 RETURN 1 2 EXPOSURE Move the cursor to EXPOSURE press the OK button to enter the sub menu Press left right key to set the relevant parameters of AGC amp Brightness Sens up D WDR DEFOG can also be set EXPOSRURE SHUTTER
10. o enter the sub menu of ADJUST Picture could be adjusted according to user SHARPNESS AUTO OFF MONITOR LCD CRT LSC OFF ON VIDEO OUT RETURN Sharpness could be adjusted when choose the AUTO mode 18 SHARPNESS 1 LEVEL 2 STARTAGC 3 END AGC 4 RETURN Press the left right to select the monitor type LCD amp CRT LCD GAMA USER 0 45 1 BLUE GAIN 0 100 RED GAIN 0 100 RETURN RET lt CRT BLACK LEVEL BLUE GAIN RED GAIN RETURN 19 9 Exit After the parameter establishment completes when it needs to preserve choose SAVE amp END and click OK button to save the changes Camera will return to factory set if click the RESET button If don t want to save the changes just choose the NOT SAVE and click OK to Exit OSD menu 20 II Technical Specification Imaging Sensor 1 3 Megapixel CMOS Signal System PAL Horizontal resolution 720P Electronic Shutter PAL 1 50 1 100000s S N Ratio More than 52dB Video Output 1 0Vp p 75 ohms Minimum Illumination 0 01 Lux F1 2 0 Lux with IR Day amp Night ICR Syn System Internal BLC BLC OFF HSBLC Video Output BNC Power Supply DC12V Operation Temperature 20 C 50 C Operation Humidity 10 90 RH Lens 3 6mm Cable length 0 4m 21 Ill FAQ 1 Q No image after installation a Check to
Download Pdf Manuals
Related Search