NX1248-E User Manual - Elvey Security Technology
Contents
1. Expansion Power trouble Expansion Power trouble Expansion RF Jammed Expansion Trouble Zone Lost Press Open circuit has occurred on the bell or siren circuit An auxiliary reporting device has failed to communicate A box containing an expansion device has been opened An expansion power supply has a low battery A short circuit of an expansion devices power supply has occurred The main power to an expansion power supply is not on The main power to an expansion power supply is not on A radio receiver is being jammed Not applicable to all controls An expansion device or keypad is not reporting to the control panel A wireless or multiplexed zone device is not reporting to the control Press to identify the zone 20 LCD Keypad Zone Low Batt Press A wireless device has a low battery Press 2 to identify the zone Zone Tamper Press A zone is tampered Press Il to identify the tampered zone Zone Trouble Press A zone is experiencing some form of trouble probably wiring Press 9 to identify the zone APPENDIX A EVENT LOG NOTE Your system may not have all of the features listed in this table D2. LCD KEYPAD SCROLL KEYS This systemis O isnot O partitioned NUMERIC CODE ENTRY KEYS PROGRAMMABLE EMERGENCY ACTIVATION KEYS Tum the Door Chime OrvOtt Pross eH d Reset Smoke Detector Press Ill Installation Company Monitoring Centar eta The emergency actuation keys must be had for 2 seconde The AWAY key is on when the system is armed in the AWAY mode It is off when the system is disarmed It will flash when there has been an alarm during the previous cycle The NIGHT key is on when the system is armed in the NIGHT mode It is off when the system is disarmed It will flash when there has been an alarm during the previous cycle The BYPASS key is on when any zone in this keypad s The STAY key is on when the system is armed in the STAY partition Is bypassed If it is off no zones are bypassed mode It is off when the system is disarmed It will flash when there has been an alarm during the previous cycle LCD KEYPAD TABLE OF CONTENTS GLOSSARY OF TERMS sisi Had Gain EE nel sai 3 UNDERSTANDING THE LIGHTED KEN 4 EMERGENCY ACTIVATION KEN 4 KEYPAD FUNGTIONS ees ret deed EEN 5 ARMING YOUR SYSTEM IN THE AWAY MODE see 5 MAKING YOUR SYSTEM READY TO ADM 6 ARMING YOUR SYSTEM IN THE STAY MODE eee 6 USING THE QUICK ADM 7 DISARMING YOUR SYS EM ee ecceece eee eect ee eee eee eeee sees taeteeeeaeeeeeeaeeas 7 ABORT FEATURE w2 0 0 c
3. LCD Keypad 15 DISPLAYS IN THE PARTITIONING MASTER MODE ARMED and READY STATUS The LCD screen will display the Armed and Ready status of ALL eight 8 partitions if any or all of the areas is armed or not ready This display is reflecting all 8 areas are 12345678 Ready and Area 5 is disarmed NOTE If a number is flashing on the Armed line that area is armed Instant If a number is flashing on the Ready line that area is ready to be Force Armed 1234 678 If ALL areas are disarmed and ready to arm this display will appear on the LCD screen System Ready Type code to arm ARMING AND DISARMING MULTIPLE PARTITIONS To arm disarm multiple partitions enter a code that has arm disarm authority for ALL of the partitions to be armed disarmed The following display will appear on the LCD screen The numbers on the top line represent the 12 45 78 Disarm gt disarmed areas to which this code has access The numbers on the bottom line 3 67 Arm represent the areas that are armed Refer to the following table for possible conditions L D DISPLAY FOR AREA TOP LINE OVER BOTTOM LINE CONDITION Skt Area Not used or Authorized Blank Dash Dash Area Not Ready Flashing Area Dash Area Ready to Force Arm Dash Flashing Area Area Armed Instant Area Dash Area Disarmed amp Ready to Arm Dash Area Area is Armed 16 LCD Keypad m To disarm all
4. Service Required Type 2 for help The Service Required message will be displayed periodically if the security system requires service Call your service provider promptly if this message is observed If you see this display press 2 One or more of the following fault messages will be displayed Use the scroll keys A V to browse through them To exit the service messages press Control Box tamper Control Fail to Comm Control Ground fault Control Loss of time Control Low Battery Control Over current Control Phone trouble Control Power trouble Optional The Box Tamper circuit has activated The control attempted to communicate a message to the Central Station but was unsuccessful A short to ground has been detected on a control circuit Your system has lost total power and needs the clock reset The standby battery is low A short circuit of a controls power supply has occurred The phone line connected to the control is not operating properly The main power to your system is not on LCD Keypad 19 Control Siren trouble Expansion Aux comm fail Expansion Box tamper Expansion Low Battery Expansion Over current
5. or Off 3 Press A to turn the X 10 device On or press W to turn the X 10 device Off The LCD screen will again prompt you to Select Light Number 0 9 Repeat Steps 2 and 3 until complete 6 Press to exit from the X 10 menu CHANGE LANGUAGES This function allows you to switch between the two languages programmed in your keypad NOTE You must exit any other function mode before attempting to change languages 1 Press 4 9 The LCD keypad is now toggled to the second language 2 Repeat Step 1 to revert to the first language CHANGING USER CODES 1 Press 5 The LCD Screen will prompt for a code 2 Enter master code The LCD Screen will prompt for a user number NOTE For partitioned systems if you are changing the code of another person you must have access to all partitions or at least all of the partitions to which the other person has access LCD Keypad 11 Enter the user code Depending on the control panel in your system this will be either a 2 digit or 3 digit number Remember to enter leading zeros i e 0 0 4 for user number 4 The LCD keypad will display the current code for this user Stars kl represent blanks NOTE To delete a user code press for a 4 digit code or for a 6 digit code Enter the new user code for that individual If you are changing the current code you may use the up and down scroll keys
6. If not contact the installing company 2 Enter your 4 or 6 digit user code to arm the system LCD Keypad 5 m The AWAY key will illuminate steady The STAY and NIGHT keys will flash during the exit delay m You may now leave the building The keypad tones will accelerate during the last 10 seconds of the exit delay You may wish to disarm and re arm the system if more time is needed MAKING YOUR SYSTEM READY TO ARM If the System Ready message is not displayed a zone is not secure To identify this zone press A V to the right of the display to browse through the zones that are not normal If you wish to bypass or unbypass one of these zones press BYPASS while that zone is being displayed When finished viewing the zones press to return to the code entry screen ARMING YOUR SYSTEM IN THE STAY OR NIGHT MODE 1 Close all protected doors and windows m The System Ready message will be displayed when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready status m The security system will not arm if the System Not Ready message is displayed It can be force armed if the entire System Not Ready message is flashing Refer to the section Making Your System Ready to Arm m If the Service Required message is alternated displayed you may not have AC power Restore power if possible If not contact th
7. The display will now begin scrolling though a list of functions and the corresponding numbers associated with those functions 2 Press the number listed on the display in order to access that particular function Hint H you already know the function numbers simply press x followed by the function number The following list of menu selections will scroll automatically NOTE Some of the functions are not listed because they are installer level functions The next menu item will be displayed each time is pressed Press to exit Select an Option This is a sample of the display The list Press A for Hein below reflects the available functions t Zone Review 46 Light Control 97 Set Date Time 0 Set Tone 49 Espanol BYPASS Walk Test 1 Chime 5 User PIN AWAY Silent Exit 2 Service Check 6 User Authority 3 Alarm Memory 7 Detector Reset 44 Test 90 Log Review 45 Display Test 91 View Settings LCD Keypad 9 VIEW ZONE STATUS 1 Press A The LCD Screen will display the zone status 2 Usethe up and down scroll keys to browse through the descriptions The LCD Screen will display the list of all zones in sequential order by zone number 3 Press to exit SETTING THE KEYPAD TONE 1 Press 0 Keypad is now in the Adjust Tone mode 2 Press A to adjust the keypad sounder to higher tones Raise tone 3 Press V to adjust the keypad sounder to Lower tone 2 lower tones 4 When the de
8. NOT WORKING PROPERLY THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE SECURITY SYSTEM IF YOU DO NOT UNDERSTAND ANY PART OF THIS MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY READ THE ENTIRE MANUAL AND IF POSSIBLE PRACTICE ON THE KEYPAD CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS ON SITE The SECURITY CONTROL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the Keypad Control which is similar to a telephone keypad If your Security Control has been so programmed you may be able to turn on ARM your System by simply double pressing the AWAY STAY or NIGHT key The system must always be Disarmed using a 4 or 6 digit code The LCD keypad includes 4 lights and a 32 character liquid crystal display and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the lights and sounds mean will help you to easily operate your system KEEP IN MIND THE LEVEL OF SECURITY YOU WILL OBTAIN WITH THIS SYSTEM RELATES SPECIFICALLY WITH TWO MAJOR FACTORS 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system YOU SHOULD BE AWARE OF THE FOLLOWING FACTS WHEN PREPARING A SAFETY SECURITY PLAN FOR YOUR HOME BUSINESS 1 Your security syst
9. the siren is running it can be silenced by entering a code with the authority for the area s that are in alarm NOTE The BYPASS AWAY STAY and NIGHT keys will only work if an individual partition is selected LCD Keypad 17 KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad and may sound for any of the following reasons E Beeps for all keypresses H Sounds a continuous tone during the Entry delay time E Pulses when a day zone is violated while the system is disarmed E Pulses when a FIRE zone has a trouble condition a Pulses when the armed status changes and the AC power is off H Beeps 3 times for trying to arm with the System Ready message off if force arming has not been selected H Beeps 1 second for the CHIME feature H Beeps 1 second at the end of the exit delay m Beeps to indicate telephone line fault if selected H Beeps rapidly to alert you that there are only ten seconds remaining in the exit delay H Beeps 3 times every minute indicating a low battery or missing transmitter is detected if wireless device is in system Entering code will suppress the sounder for 12 hours Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists 18 LCD Keypad SERVICE DISPLAY
10. ISPLAY DESCRIPTION TXlobat Transmitter The transmitter has a low battery Low Battery ZN Lost Zone Lost A wireless or multiplexed zone device is not reporting to the control Duress Duress The control has been armed or disarmed with a Duress code Man Fire Manual Fire Keypad Fire has been activated Aux 2 Auxiliary 2 Keypad Medical has been activated Panic Panic Keypad Panic has been activated KP Tamper Keypad The keypad tamper has been activated Tamper BoxTamp Box Tamper The box tamper circuit has been activated AC Fail AC Fail AC failure has been detected OverCur Over Current A short circuit of a power supply has occurred Srn Tamp Siren Tamper A siren or speaker tamper has been detected Tel Flt Telephone A telephone fault or tamper has been detected Fault Exp Trb Expansion An expansion device or keypad is not reporting Trouble to the control LCD Keypad 21 DISPLAY DESCRIPTION Log Full Log Full The event log is full Old events will be pushed out as new ones enter the log Open Open Reports user number date time and partition of opening Close Close Reports user number date time and partition of closing Exit Err Exit Error Entry Exit zone was faulted at the instant the exit delay expired Rec Close Recent Close An alarm occurred within 5 minutes after the control was armed Autotest Auto Test Sending
11. MED Optional Double pressing the AWAY STAY or NIGHT key will change to the corresponding mode Once the AWAY mode is entered the system must be disarmed to change modes DISARMING YOUR SYSTEM When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a continuous tone for the duration of the entry delay time or until you enter a valid code 1 Enter a valid user code Type 3 code wo Disarm 2 The currently armed key AWAY STAY or NIGHT will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the AWAY STAY or NIGHT keys are all flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location LCD Keypad 7 ABORT FEATURE Optional if programmed Entering a user code during an alarm report to the central station will stop the communication of all abortable reports NOTE The abort feature must be enabled Entering a user code after an alarm report to the central station will send an appending report to the central station after the cancel report NOTE The cancel feature must be enabled BYPASSING ZONES If you wish to bypass one or more zones this must be done while the system is in the disarmed state If the zone i
12. a communicator test at a specified interval Start Prog Start Local programming is started Programming End Prog End Local programming is ended Programming Start Dnid Start Download Download session is started End Dnld End Download Download session is ended Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm Gnd Fit Ground Fault A short to ground has been detected Man Test Manual Test Bell and or communicator test while system is in disarmed condition Re exit Re Exit The exit delay has been re started without disarming the system Output Trip Output Trip A trip has occurred on an expander auxiliary output Data Lost Data Lost Communication of a signal has failed log only event Walk test Walk Test A zone Walk Test mode has been activated End Test End Test Test has been ended Cross Trip Cross Trip The first zone of a cross zone has been tripped log only Expansion Expansion An expansion module created an undefined Event Event event Partial Arm Partial Arm Reports a closing in the stay mode 22 LCD Keypad DISPLAY DESCRIPTION Listen In Listen In A listen in function has been activated Service Start Service Start Technician is on site Service End Service End Technician is off site Code Entry Code Entry A code has been entered First Open First Open Reports when the first partition is disarmed Last Close La
13. ay all of the partitions to which this user has access If you wish to remove a partition press the partition number on the keypad and the display will mark that partition with a hyphen indicating access has been removed If you wish to re establish user access to the partition press the partition number again 5 Press to save the data The LCD will then prompt you for the next user code 6 If another user code needs to be programmed return to Step 3 If not press to exit this feature without saving the data RESET FUNCTION This function is used to reset Smoke Detectors Zone Troubles and Zone Tampers 1 Disarm the system if it is not already disarmed 2 Press 7 Resets have now been performed 3 Ifthe keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code This log contains a listing of the events along with date time and partition where the event occurred 1 2 To view the log press 9 0 The LCD screen will prompt you for a code Enter your master code The LCD screen will now show the most recent event To view the events from most recent to the oldest press W LCD Keypad 13 4 To view th
14. e events from the oldest to the newest press A The display contains the following information Event gt Open 75 User or Zone ID Date gt 9 25 17 57 P3 Indicates partition Month Day ef Time shown in and indicates an 24 hour format event not reported This screen shows an opening of Partition 3 on September 25 at 5 27 p m by user 75 The shows that this event is not programmed to be reported to the central monitoring station Refer to Appendix A on page 21 for a list of possible log messages ADJUSTING THE VIEW BRIGHTNESS OF THE LCD 1 Enter 9 1 The LCD will prompt for a code Enter master code The LCD will prompt you to raise or lower the view Use A V to raise or lower the viewing angle of the text bk o N Press to advance to the Brightness option The LCD will prompt you to brighten or dim the LCD lighting Use A V to adjust to desired brightness 5 Press to exit SETTING THE SYSTEM CLOCK 1 Enter 9 7 The LCD Screen will prompt for a code 2 Enter master code The time and date will be displayed with the current hour flashing 3 Use A V to select the proper hour 4 Press to move to the minutes day of week date month and year 5 Repeat Steps 3 and 4 until the entire time and date are set 14 LCD Keypad USING THE DOOR CHIME FEATURE The door chime is turned on or off by pressing 1 Each time 1 is pressed it wi
15. e installing company 2 Enter your 4 or 6 digit user code Optional if programmed H f Auto Bypass is enabled all interior zones will be bypassed if you do not leave through a designated entry exit door If Auto Bypass is enabled omit Step 3 3 Press STAY m The STAY key will illuminate indicating that all interior zones are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area 6 LCD Keypad m The BYPASS key will illuminate if any zone s are bypassed If any zone s have been bypassed previously by the user the light s corresponding to the bypassed zone s will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm To toggle between the STAY and NIGHT mode double press the key corresponding to the mode you desire To upgrade from the STAY or NIGHT mode to the AWAY mode double press the AWAY key 45 Once the AWAY mode is activated the system must be disarmed to revert to the STAY or NIGHT mode USING THE QUICK ARM The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system in the AWAY STAY NIGHT modes by pressing the corresponding AWAY STAY NIGHT key twice This feature is used for ARMING ONLY and will not disarm the security system This is ideal for a maid or baby sitter etc CHANGING MODES WHILE YOUR SYSTEM IS AR
16. eighbor s phone NOTE After the installation of your Security System has been completed notify your local Fire and Police Departments to give them your name and address for their records Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms This equipment should be installed in accordance with the National Fire Protection Association s Standard 72 For additional information write the National Fire Protection Association Batterymarch Park Quincy MA 02269 BEDROOM LIVING BEDI M BEDROOM D L ROOM noe FIRST FLOOR SECOND FLOOR OO OL Im FRONT Y e C BACK 24 LCD Keypad GE Security LCD USERS MANUAL 1248EUB04 REVB May 2004
17. el wie sien EES teas 8 BYPASSING ZONES nsiet orisii aeaaea 8 EL UE gd E E T 9 UNBYPASSING EE 9 EUNGTION MEN 12 ingini a tee 9 VIEW ZONE STATU Sarnia a N a E 10 SETTING THE KEYPAD TONE sesssessssesssrsrerrsrisrerrsrnrrsrnrrnrrererenrnrrnrnet 10 VIEW ALARM MEMORY 10 TEST FUNCTION 3 002222 nik a ee eal dee ce deen 10 DISPLAY TEST FUNCTION 2 uestteee eegen earee ge deer noite 11 LIGHT CONTROL FOR X 10 DEVICES 00 eect eee eee tee tee eeeteees 11 CHANGE LANGUAGES AA 11 CHANGING USER CODE 11 ASSIGNING USER CODE AUTHORITY LEVELS eee ee 12 RESET FUNGTION ebessen dee ege eebe 13 READING THE EVENT LO 13 ADJUSTING THE VIEW BRIGHTNESS OF THE LOD ee 14 SETTING THE SYSTEM CLOCK 0 0 ecee eee cee tee teat teteeeeeeteeeeeeeaee 14 USING THE DOOR CHIME FEATURE cee eee eee teeter tenets 15 PARTITIONED SYSTEMS OPERATION eee eee tees te teeeeneeaeees 15 INDICTORS IN THE PARTITIONING MASTER MODE ee 15 DISPLAYS IN THE PARTITIONING MASTER MODE eee 16 KEYPAD CONTROL TONES DEED 18 SERVICE DISPLAY Eege he din Eai 19 APPENDIX A EVEN d ses dain nya aside hohe 21 EMERGENCY EVACUATION PLANS 000 eect e eee eter tee tee ete teat tee teaee 24 LCD Keypad THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM
18. em is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security 2 Your system should be tested weekly 3 Your system will not work without power 4 Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event 5 Smoke and heat detectors may not detect heat and smoke in all situations 6 Use qualified security professionals to install and maintain your security system 7 It may be possible to arm the security system without the backup battery connected Your periodic test should be done with A C Power removed to verify the battery is connected and adequately charged 8 Care should be taken to plug in and restrain the A C Transformer after testing PLEASE READ THE FOLLOWING INFORMATION AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR SECURITY CONTROL SYSTEM IF YOU DO NOT UNDERSTAND ANY PORTION OF THIS MANUAL OR IF YOU HAVE ANY QUESTIONS ABOUT YOUR SYSTEM CONTACT THE INSTALLING COMPANY 2 LCD Keypad GLOSSARY OF TERMS Abort Delay An option that allows a delay in reporting to the central station Authority Level The level of access an individual has when using an alarm panel Central Station Location where alarm data is sent during an alarm report Chime Feature An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a p
19. erson or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either 4 digit codes or 6 digit codes but not a mixture of the two Duress Code An option that allows a special code to be sent to the central station indicating the alarm system is being operated under duress Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the entire message System Not Ready For Help press A NOTE Those zones that are not ready will not create an alarm Function Code A Function Code is either a 4 digit or 6 digit code programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Instant Delay An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm Master Code A master arm disarm code that can program other user codes Partitioned System A system divided into multiple areas in which its own user or users control each area Perimeter The outer edge of the protected area LCD Keypad 3 Quick Arm An option that allows you to turn on ARM the security system by double pressing either the AWAY STAY or NIGHT key on the keypad for ARMING only as programmed by the
20. installing company User Code A 4 digit or 6 digit entry code used to arm or disarm the system UNDERSTANDING THE LIGHTED KEYS AWAY STAY NIGHT keys ON when the system is armed to one of these respective modes OFF when it is disarmed FLASHES when there has been an alarm during the previous arm cycle BYPASS key ByPass ON when any zone in this keypad s partition is bypassed OFF when no zones are bypassed OOOO EMERGENCY ACTIVATION KEYS NOTE You must press and hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activations e J Fire Auxiliary Emergency Police Fire Key If programmed you can activate the Fire alarm by pressing the Emergency Activation Fire key for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center This key should only be pressed in an emergency situation requiring response by fire department personnel Auxiliary Key If programmed you can activate the auxiliary alarm by pressing the Emergency Activation Auxiliary key for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center This key should only be pressed in an emergency situation requiring response by emergency personnel 4 LCD Keypad Police Panic Hold Up Key If programmed when the Emergency Activation Police key is pressed for tw
21. ll toggle the chime feature on off and produce a momentary ding dong sound PARTITIONED SYSTEMS OPERATION This systemis Q isnot partitioned If your system is multi partitioned and the keypad resides in one partition your keypad will provide the status of the zones in your partition by using the screen messages described earlier in this manual The Master Mode of operation allows you to temporarily access any partition providing your code is authorized within the system and to perform functions in other partitions Read this entire manual to understand the various messages displayed on your keypad screen INDICTORS IN THE PARTITIONING MASTER MODE m BYPASS will illuminate if ANY area has a zone bypassed m AWAY will illuminate steady if ALL partitions are armed and at least one of those partitions are in the AWAY mode H STAY will illuminate steady if ALL partitions are armed and at least one of those partitions are in the STAY mode H NIGHT will illuminate steady if ALL partitions are armed and at least one of those partitions are in the NIGHT mode m AWAY STAY NIGHT will all flash if an alarm has occurred in any partition OR if a partition is in an exit delay with one or more other partitions disarmed m SYSTEM READY message will display on the LCD screen if ALL partitions are ready to be armed m SOUNDER will sound if ANY area has the sounder on This includes Entry delay Exit delay Chime and Alarm
22. o seconds a local audible alarm will sound If your system is connected to a monitoring center an emergency report could be transmitted to that center These keys should only be pressed in an emergency situation requiring immediate response by law enforcement personnel NOTE Some Panic Hold Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center Check with your installing company to determine how your security system will respond to the Panic Hold Up activation KEYPAD FUNCTIONS No one at premises total interior and exterior protection Building is occupied protection around the perimeter Building is occupied protection around the perimeter and selected zones doors windows sensors COW ARMING YOUR SYSTEM IN THE AWAY MODE 1 Close all protected doors and windows m The System Ready message will be displayed when all protected zones and sensors are secure NOTE If any zones are bypassed a System Ready sensor in that zone can be violated without affecting the TYPe Code to Arm ready status m The security system will not arm if the System Not Ready message is displayed It can be force armed if System Not Ready the entire System Not Ready For help press A message is flashing Refer to the section Making Your System Ready to Arm m Ifthe Service Required message is alternately displayed you may not have AC power Restore power if possible
23. of these areas press A To arm all of these areas press V To toggle a single area between the armed and disarmed conditions press Area number For example If Area 4 is armed Il 4 will disarm Area 4 If Area 4 is disarmed 4 will arm it m Press AWAY STAY or NIGHT once to arm all authorized partitions into the corresponding mode m To control the individual areas refer to the following section OPERATING INDIVIDUAL AREAS IN THE MULTI PARTITION MODE Enter a code that is a valid arm disarm code for the area you wish to operate The following display will appear on the LCD screen Only the areas authorized by this code will 12 4 78 appear Disarm gt 3 56 Arm gt To toggle between the armed and disarmed states of an individual area press Tal Area number To operate an individual area enter the number of the partition you wish to operate The LCD keypad will now operate as a single area keypad All keys and functions entered will affect this individual partition only The lights and display represent the status of that partition only The word System will be replaced with the word Area The following is an example of this feature To exit this screen press Area 5 is selected and Area 5 is ready to Area 5 Ready arm To exit the individual partition mode enter Type code to arm SILENCING ALARMS IN THE MULTI PARTITION MODE If the keypad is sounding an alarm or
24. s not known refer to Procedure B If you know the number of the zone to bypass 1 Jm Fb wo Press BYPASS When the LCD prompts for a code optional if programmed enter your user code The bypass light flashes Enter the zone you wish to bypass Example Press 6 for zone 6 Press BYPASS again The zone is now bypassed Repeat steps 4 and 5 for any other zone s that need to be bypassed Press BYPASS again OR press to exit the Bypass Mode The bypass light will stop flashing upon exiting the Bypass Mode Pressing A or Y will display all bypassed zones Press to exit this viewing mode If you do not know the number of the zone you wish to bypass 1 2 3 Press A The description for zone 1 will be displayed Press A or V to browse through the custom descriptions for the zones To bypass or unbypass a specific zone press BYPASS while that zone is displayed When finished press to return to the code entry screen LCD Keypad GROUP BYPASS 1 Press BYPASS 0 BYPASS All zones that are designated as group bypass zones will be bypassed 2 Press BYPASS again to exit group bypassing UNBYPASSING To manually unbypass zones perform the bypassing procedure on a zone that is already bypassed NOTE All zones will automatically be unbypassed each time the system is disarmed FUNCTION MENU The functions listed below are found in the Function Menu 1 Press
25. sired tone is reached press to set this tone and exit from the Adjust Tone mode VIEW ALARM MEMORY 1 Press 3 to display the zone s on the keypad that created the last alarm 2 The LCD Screen will display the zone description for those zones Alarm Memory 1 3 Press to exit the alarm memory ZONE 1 TEST FUNCTION Optional if programmed If programmed this function will perform a battery test communicator test and or a siren test No alarms will be sent and no reports will be sent unless a communicator test is performed in which case a test signal will be sent 1 Press 4 4 The test will be performed as programmed 2 Ifthe siren test is performed enter a user code to silence the siren 10 LCD Keypad DISPLAY TEST FUNCTION This function will perform a test of the LCD display No alarms or reports will be sent 1 Press 4 5 The test will be performed and all of the display pixels and keys will flash until another key is pressed 2 Press any key to end the test LIGHT CONTROL FOR X 10 DEVICES Optional if programmed This menu allows you to control up to ten X 10 devices from each keypad 1 Press 4 6 The screen will prompt you to Select Light Number 0 9 2 Enter the number of the X 10 device you want to control The LCD screen will show the light number on the left On the right side of the display it will prompt you to turn the light X 10 device On
26. st Close Reports when the last partition is armed Sprnkir Sprinkler Instant sprinkler supervisory report Clock Set Clock Set Clock has been reset RF Jammed RF Jammed A wireless expansion module is jammed CleanMe CleanMe A smoke detector requires cleaning LCD Keypad 23 EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition For example the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building Draw up a floor plan of your home Show windows doors stairs and rooftops that can be used for escape Indicate each occupant s escape routes Always keep these routes free from obstruction Determine two means of escape from each room One will be the normal exit from the building The other may be a window that opens easily An escape ladder may have to be located near the window if there is a long drop to the ground below Set a meeting place outdoors for a headcount of the building occupants Practice escape procedures In a home sleep with bedroom door closed this will increase your escape time If you suspect fire test the door for heat If you think it is safe brace your shoulder against the door and open it cautiously Be ready to slam the door if smoke or heat rush in Practice escaping to the outdoors and meeting in an assigned spot Call the Fire Department from a n
27. to select the digit to change and enter the correct number If it rejects the code because of duplication or such the sounder will beep 3 times Return to step 3 if another user code needs to be programmed To exit Code Programming press while the LCD screen is prompting for a new user ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning authority levels NOTE You must have authority to the partition you wish to add or remove from another person s authority 1 2 3 Press 6 The LCD Screen will now prompt for a code Enter master code The LCD Screen will prompt for a user number Enter the user code Depending on the control panel in your system this will be either a 2 digit or 3 digit number Remember to enter leading zeros i e 0 0 4 for user number 4 The LCD will now prompt you for the user attributes PROMPT fp eee ae a Outputs used Open Close Rprt Bypass enable These are for use by a professional installer only Arm Disarm Master code 0 No 1 Yes Your keypress will apply to the user code you entered in Arm only Step 3 Reserved Output 4 Output 3 Output 2 Output 1 Sched arm only If these messages appear on the LCD screen press until you return to the prompt for the user code or until you exit this adjust mode LCD Keypad 4 NOTE The LCD will now displ
Download Pdf Manuals
Related Search