SVEA_user_manual_low..
Contents
1. In order to change the digit type the following command from the phone connected to SVEA E data digit where data digit is the digit that shall be used before the modem number Valid value range is from to El and If the value you entered is valid it will be confirmed by a double confirmation tone Data Call forcing the Calling Tone function In order to force the Calling Tone function for the modem and obtain as a result to communicate SVEA the intention to make a data call it is necessary to end the called modem number with the 4 character Establish a data call Connect the analogue modem with SVEA Make sure that the device is on and running Internet connection to establish an internet connection using your PC s browser you shall define a remote access configuration including the parameters relative to the connection by means of your provider Digits characters mentioned above should be put before after the provider number Data connection by using a terminal emulation programme such as HyperTerminal type the ATD command followed by the phone number from the PC connected with the modem Never forget to type the digits characters mentioned above before after the modem number Example to establish a data connection with the number 555 123456 without forcing the Calling Tone function type ATD 555123456 Example to establish a data connection with the number 555 123456 forcing the Calli2. e n case of intervention always make sure that the device is completely and properly disconnected e n case of fire avoid using water as an extinguisher Since the GSM system is a radiofrequency technology RF it may interfere with the operation of other phone sets or electronic equipment that is not properly protected against radio frequency radiation e Never put your hands on the antenna when the device Is in use e Never use the device if the antenna is visually damaged In this case ask for a replacement antenna through your service center e During device operation you should keep a minimum distance of 20cm from the antenna e People with auxiliary systems such as pacemakers and electro acoustic hearing aides should keep at a safe distance 3 2 Precautions e ATTENTION Many of the components used in this device are sensitive to electrostatic discharge e f you should handle connection cables make sure the device is unplugged and avoid direct contact with the conductor terminals POSSIO SVEA USER MANUAL e For cleaning operations use a soft and dry cloth or a piece of cloth soaked in a light detergent solution Never use any type of solvent such as alcohol or gasoline in order to avoid damaging the finish e The non observance of the above precautions might permanently damage the device 3 3 Warnings on the use of the battery The SVEA product is supplied with a hermetic lead battery Follow the
3. 5 1 Contents of the box e SVEA unit e Antenna e Battery e Wall mount e AC cord e User Guide 5 2 Installation Guide You need the following items and tools to perform the installation a Phillips screwdriver b SIM card fax number subscription c Fax phone 5 2 1 Unscrew bottom To have access to the SIM card compartment it is necessary to remove the plastic cover of the device completely by following the below steps a Remove the terminal compartment and the second transparent protection by unscrewing the two fastening screws b Unscrew the four screws on the back of the device c Remove the upper plastic cover 5 2 2 Insert SIM card Lift the SIM reader of a SIM lock type and insert the SIM card Make sure that the contacts are turned downwards Then close the SIM reader again by pushing the slide downwards until you lock it into place completely e ooo on non ne e e oo cono ensos s ocn 00 00 00 no 0 CU CO UC OC On O nn 0 0 UC 0 00 0 000 0 00 0 Cn 000 0 00 0 0 0 0 0 0 0 0 4 POSSIO SVEA USER MANUAL Ce ee 0 00 000 0 0 0 00 an 0 00000 0 0 0 0 00 0 0 0 0 0 0 0 04 IMPORTANT e Before inserting and removing the SIM card power off the device and unplug it e For data and fax calls make sure that the SIM card is properly enabled with the numbers relative to the data and fax service in addition to the voice number e Make sure that the PIN code on the SIM card has been disabled before
4. 2 6 Plug in the RJ11 15 bed Power up unit 15 e o oo c eoososos n 6 cs o o coo nn Cn 0 On oo n o o oo on e n e on o e ee o ono oo eones ers s ss sS o 0 0 4 POSSIO SVEA USER MANUAL 2 Technical Specification 2 1 Physical Description 220mm x 170mm x 50mm 1 Weight battery included 4009 Operating temperature From 20 C to 55 C From O to 95 not condensed 2 2 External Connections Telephony PSTN connection RJ 11 connector GSM antenna SMA female connector 500 Power supply input 230V AC 50 60Hz or 12V DC 1A 2 3 Consumption Average power consumption 85mA stand by 350mA call mode 12V DC 2 4 PSTN Connection Point AU Features Call mode Originated call MOC terminated call MTC Local tone frequency 425hz 1 Local tone modulation accuracy emission 1 silence 326mA with OO of ine resistance PSTN connection point characteristic 7500 150nF 2700 impendence Maximum telephone line length 500 metres depending on the number of units connected POSSIO SVEA USER MANUAL ee 2 5 Modem Data Service via AU Interface Transmission speed 9 6kbps SVEA modem local connection up to V 90 2 6 Fax Service via AU Interface Transmission and reception Group 3 Compliant with ITU T T 4 and T 30 2 7 GSM Performance GSM dual band RF power Class 4 2W for EGSM900 Class 1 1W for GSM 1800 Voice and emergency calls
5. TCH FS Voice Half Rate HR Full Rate FR Enhanced Full Rate EFR Automatic Group 3 Class 1 2 Data transmission GSM 9 6kbps uplink and downlink CSD up to 14 4kbps USSD non transparent mode V 110 e o on nn 0 0 00 00000 000 0 ne coo e nene e orn oe ooo 000 0 e eo 0 0 000 00 000 000 0 e ne e e 0 0 0 0 0 0 0 0 0 0 0 0 0 04 POSSIO SVEA USER MANUAL Ce oeooooooooooooooooooooo oooooooooooooooooo ooo o ooo o ooo o oooooooo ooo oooooooooooooooooo ooooooooooooooooooooooooooooooo 3 Warnings and Precautions 3 1 Safety Rules e The passage from a cold room to a warm room may cause condensation to build up Inside the device In these cases it is recommended to wait at least 1 hour before using the product in order to avoid any malfunction e ATTENTION Connect the device with an outlet installed in the immediate proximity and easily accessible for the operator Under no circumstance is It permitted to cut the mains plug to connect the equipment securely e ATTENTION Electrical shock risk The power supply used for this device can cause lethal voltage levels e The case includes a connection compartment and arrangement You may have access to it after removing the cover by means of a tool e f any object or liquid should enter the device immediately remove the device from its power supply Before reusing the device have it checked by an authorised technician
6. below recommendations e Danger of explosion if the battery is either replaced or connected improperly pay attention to its polarity and features e Replace the battery with one of the same type or with an equivalent one e Never short circuit damage or disassemble the battery e Never expose the battery to liquids e For disposal follow local procedures Never dispose of the battery with the normal garbage or into the environment e Avoid any contact with battery acid The electrolyte is highly toxic and it may cause serious damage by way of contact only It may even release dangerous gases if in contact with other materials In case of contact with the battery acid e Wash with abundant water immediately and neutralise with a soda based solution e Incase of ingestion immediately proceed to your local hospital for treatment e Itis recommended to request for a replacement through the service centre Ce rs nn 0 0 00 000000 000 0 ne 0 000 0 0 O 00 O 00 0 000 0 00 00 00 0 00 000 e 000 00 0 000 000 00 0 000 0 0 0 000 00 0 000 nn 0 00 0 0 0 0 0 o 0 0 0 0 04 POSSIO SVEA USER MANUAL ee 00000000 0 0 0 000 0 0 0 00 an 00000 00 0 0 00 0 0 0 0 0 0 0 0 4 4 Description SVEA is the easiest way to get telecommunication services to premises that cannot be reached by telephone landlines PSTN but where there is adequate GSM coverage Through the GSM network SVEA allows the user to make and receive calls from a common analogue t
7. inserting the SIM into the device 5 2 3 Backup Battery arrangement with 230V AC power supply only The backup battery must be arranged inside SVEA only if you use the 230V AC primary network as a power supply source If you use photovoltaic panels or 12V DC the backup battery shall not be used IMPORTANT if you handle or transport SVEA tor mechanical and electrical safety reasons the backup battery shall not be arranged inside the product The insertion of the battery inside the product and the connection of its electrical terminals must only occur at the time of commissioning at the end user s premises To arrange and connect the backup battery remove the SVEA plastic cover as It has already been described for the SIM card insertion Then follow the below steps e Make sure the stripped terminals cables intended to connect to the backup battery are securely fixed to the 3 pole terminal the red cable should be fixed into the BAT position and the black cable into the GND position e Insert the fast on connectors into the battery terminals Pay attention to correct polarity e Arrange the battery in the compartment available in the printed circuit and make sure that the terminals are turned to the right IMPORTANT Red Cable Terminal Black Cable Terminal ee POSSIO SVEA USER MANUAL Ce eee ee ee ee 0 000 0 000 00 an 0 00000 00 0 0 00 0 0 0 0 0 0 0 04 e Place the battery in the area as shown in the picture
8. of a congestion or engaged tone may mean that there is no field or that SVEA is already engaged in another call e Wait no longer than 14 sec to dial the number you want to call on the phone keypad and wait for the connection Wait no longer than 4 sec between digits timeout set by factory After the above periods SVEA will send the digits you have dialled e When you wish to terminate the call hang up the phone handset ATTENTION at the end of a voice call wait about 2 seconds before the next call To receive a voice call When you receive a voice call your attached phone will ring To answer just lift the handset or press the phones answer button You can display the number of the caller on your phone if the Call Line Identity CLI service is enabled 6 2 Fax Calls Make sure that an analogue fax Group 3 is connected with SVEA by means of the AU connector 6 2 1 SVEA is connected to an analogue fax You can send receive faxes by simply connecting an analogue fax G3 with the SVEA AU connector coco one nn 0 0 00 00000 0 00 0 0 O 00 00 O 00 00 0 00 000 0 000 00 0 0 0 000 00 0 000 0 0 00 0 0 0 O 0 0 00 0 00 0 000 000 0 000 nn 0 000 0 0 0 0 0 0 0 0 0 0 04 POSSIO SVEA USER MANUAL e ooo nn 000000 000 000 nn 00 aC e non 000000000 000 AC UU 00 0 Cn 00 000000 00 000 0 0 0 00 an 0 00000 00 0 0 00 0 0 0 0 0 0 0 04 When establishing a call most of the faxes available on the market can communicate with SVEA to a mak
9. In order to check this run a terminal emulation software e g HyperTerminal on a PC connected to the seriel port of SVEA Then type the command AT CRC 1 Wait for a fax originating from the ISDN device make sure it is send to the fax number on your SIM card If the HyperTerminal displays ring voice it is necessary to inform the fax sender that its Network Termnination NT requires an upgrade 7 7 Cannot establish a data call or an internet connection To be able to establish a data call i the user defined digit before the addressee s In order to change the digit type the following command trom the phone connected to SVEA or the home telephone system data digit where data digit is the digit that shall be used before the modem number Valid value range is from to El and If the value you entered is valid it will be confirmed by a double confirmation tone modem number the default value is The alternative in establishing a data call is to force the Calling Tone function for your modem if predisposed by ending the called modem number with the character NOTE if the modem is not forced to produce the Calling Tone and the preset digit IS not entered the call you establish will be a voice call e ooo on e non e e o oo oo ooo oo ono o o e oo ens o non ns c oos e po en oo op e e o oo oo o o o o o Y 31 10 50700 INHdO
10. Possio SVEA GSM Connector User Manual POSSIO SVEA USER MANUAL Ce oeooooooooooooooooooooooooooooooooooooooo ooo o ooo oooo oooooooooooooooooooooo oooooooo o ooo oooooooooooooooooooooooooo o 1 Foreword Before setting up and using the SVEA GSM Connector we kindly ask you to carefully read this user manual 1 1 Declaration of Conformity SVEA GSM Connector Art Nr QEQU 00040 01 complies with the regulations in force with reference to the R amp RRE 99 5 CE directive and in particular with the following standards EN 60950 Health and Safety EN 301 489 1 7 EMC EN 301 511 EN 300 607 1 RF Spectrum Efficiency 1 2 Copyright O 2006 Possio AB This user manual contains or refers to proprietary information that is protected by copyright All rights are reserved POSSIO is a registered trademark of Possio AB This guide may not be copied photocopied reproduced translated or converted to any electronic or machine readable form in whole or in part without prior written approval from Possio Improvements and changes to this guide necessitated by typographical errors inaccuracies of current information or improvements and changes of programs and or equipment may be made by Possio at any time and without notice Such improvements and changes will however be incorporated into new editions of this booklet available on the Internet at WWW possio com Possio AB P O Box 1236 164 28 Kista Sweden First edi
11. SER MANUAL CO 4 2 LED Status Report GREEN LED STATUS RED LED STATUS SVEA STATUS Off No power supply Off Very quick flashing Off SIM absent and 60 ms ON 60 ms OFF GSM Network absent or SIM PIN required Very quick flashing Fixed light SIM absent and 60ms ON 60 ms OFF GSM Network present or SIM PIN required 3 cycles of 5 quick 3 cycles of 5 quick Boot phase flashing flashing 100ms ON 100ms OFF 100ms ON 100ms OFF ea light Setup phase Fixed light Slow flashing SVEA ready 100ms ON 7 2s Off Handset hung up Off Slow flashing SVEA ready 100ms ON 7 2s Off Handset lifted 1 1 Quick flashing 1 Quick flashing Send Receive Fax 200ms ON 200ms OFF 200ms ON 200ms OFF 2 Quick flashing 2 Quick flashing Send Receive Data 200ms ON 200ms OFF 200ms ON 200ms OFF 200ms ON 200ms OFF 200ms ON 200ms OFF 1 Slow flashing 1 Slow flashing Faxes avaliable 100ms ON 2s OFF 100ms ON 2s OFF in SVEA memory 1 Quick flashing lt 1 Quick flashing lt Memory nearly full 200ms ON 200ms OFF 200ms ON 200ms OFF 1 Green and red LED flashing on and off alternative 2 Green and red LED flashing on and off simultaneously coco on nn 0 0 00 000000 0 000 0 0 oo o OCO nn 0 O 00 000 0 000 00 0 0 O 00 000 0 000 0 0 000 00000 000 0 00 0 000 0 00 0 000 nn 0 000 0 0 0 0 0 0 0 0 0 0 04 POSSIO SVEA USER MANUAL Ce ee ee ee 0 0 00 an 00 00000 00 0 0 00 0 0 0 0 0 0 0 0 4 5 Get Started
12. alue is valid SVEA will generate a double tone as confirmation 7 4 Cannot send a fax To be able to send a fax try typing the user defined digit before the receiver s fax number the default value is E In order to change the digit type the following command from the phone fax connected to SVEA or the home phone plug BEDECE H A where fax digit is the digit that shall be used before each fax number Valid value range is from to El and If the value you entered is valid it will be confirmed by a double confirmation tone Connect the analogue fax with SVEA or the home telephone plug Make sure that the device is switched on Insert the document you wish to send into the fax and type the fax number Remember to type the fax digit above before the fax number Example if you wish to send a fax to 555 123456 type 555123456 NOTE if the fax is not complete with Calling Tone function and the preset digit is not entered the call you establish will be a voice call POSSIO SVEA USER MANUAL Ce ee ee ee ee 000 000 00 an 00 00000 0 0 0 0 ooo no 0 0 04 7 5 Cannot receive a fax In order to receive faxes over the GSM network you require a separate fax number to your voice number This can be requested from you operator 7 6 Cannot receive faxes originated from ISDN devices When unable to receive faxes from ISDN devices it is possible that the problem is caused by the Network Termination NT setting
13. e a fax call Communication occurs by means of a special dial tone called calling tone also known as tone dialling or touch tone According to whether this function is available on you fax or not follow the instructions listed below to send a fax To send a fax only for faxes complete with the Calling Tone function Connect the analogue fax to SVEA Make sure that the device is on and running Insert the document you wish to transmit into the fax and type the fax number To send a fax only for faxes not complete with the Calling Tone function To be able to communicate SVEA the intention of sending a fax type the user defined digit before the receiver s fax number the default value is In order to change the digit type the following command from the phone fax connected to SVEA 4 els e 4 2 AA where fax digit is the digit that shall be used before each fax number Valid value range is from to and If the value you entered is valid it will be confirmed by a double confirmation tone Connect the analogue fax with SVEA Make sure that the device is switched on Insert the document you wish to send into the fax and type the fax number Remember to type the tax digit above before the fax number Example if you wish to send a fax to 555 123456 type 555123456 NOTE if the fax is not complete with Calling Tone function and the preset digit is not entered the call you establish will be a voice ca
14. elephone PBX fax or modem without any difference with respect to the standard PSTN line SVEA is powered up with the primary 230V AC 50 60Hz power supply It is equipped with an optional internal battery that works during any power shortage with an estimated autonomy equal to 6 hours of call time and 13 hours of stand by SVEA V ga j o o E y TELEPHONE FAX ee POSSIO SVEA USER MANUAL Ce nn 0000000 0 0 000 0 00 0 o oo an 00000 00 000 0 0 0 0 0 0 0 0 4 4 1 Description of connectors SVEA is arranged in a plastic case that shall be fastened to a wall Connectors and light signals are arranged on two sides at the bottom and on the front LEE F E Y The following connectors are shown on the bottom 1 Power supply primary power supply cable 230V AC 50 60Hz 2 Slots bottom breakable slots for running through connection cables for any external power supply source photovoltaic system and or phone duplex cable 3 PSTN connection RJ 11 analogue port for connecting analogue devices fixed phone sets PBX fax or modems 4 Reset key used to reset and or power off the device Always reset the device when switching SIM card The following are shown on the front 5 Antenna GSM dual band antenna GSM LED red it shows the GSM operation status of the device 7 Power supply LED green it shows the power supply status of the device Terminal compartment CE POSSIO SVEA U
15. emory Command to force the printout of the faxes that have been stored in SVEA without having to disable the DAY function To disable all fax reception You can disable all fax reception e g because no fax is connected to SVEA by typing the following command x ffs fr jo 1 p where y can be the following parameter values O Enable fax reception 1 Disable fax reception 2 Verify command status double tone every 2 sec indicates the service is enabled single tone every second indicates the service is disabled Store amp Forward vs Pass through operation mode In the store forward mode default setting SVEA first stores all incoming fax pages in its memory and then delivers them to the attached fax In the pass through mode SVEA operates in a transparent mode connecting the GSM e ooo ono on 000 nn 0 00 0 0 0 000 0 0 O UC nn Cn e 00 00 00 oo 0 CU CO 00 0000 O nn 0 000 0 00 0 oe oo Cn 00 0 0 00 0 0 0 0 0 0 0 0 4 POSSIO SVEA USER MANUAL Ce ee ee ee 000 000 00 an 0 00000 00 0 0 00 0 0 0 0 0 0 0 0 4 network directly with the attached fax 50500000000 Command to enable pass through function it disables store amp forward mode e Dele Ja Je fa fio Command to enable Store amp Forward function default setting NOTE If Store amp Forward mode is disabled the functions Printing report and Day function for SVEA will be disabled Printing Reports Fax report pri
16. er 4 Fasten the device to the lower anchor screw by means of the second screw by using the slot arranged in the terminal compartment ATTENTION SVEA shall always be installed vertically Avoid installing it in any other position 5 2 6 Plug in the RJ11 cable to phone or fax Use the supplied phone cable to connect the RJ 11 connector called PSTN connection point AU of the SVEA with a phone exchange PABX a type approved phone set a G3 fax terminal or an analogue modem 5 2 7 Power up unit Connect the power supply cable with a 230V mains socket The SVEA GSM Connector is now ready to use e ooo encon 000 nn 0 000 0 0 0 000 0 0 O UC nn Cn 0 On 0 00 000 00 0 00 0 0 0 0000 On 000 O nn 0 000 0 0 0 000 00 0 Cn nO 0 0 0 0 00 0 0 0 0 0 0 0 0 4 POSSIO SVEA USER MANUAL 6 Operating Modes Analogue devices must be connected to SVEA by means of the AU connector either individually or in parallel up to three devices at the same time 6 1 Voice Calls Make sure that a fixed phone set or the 2 wire analogue line port of a phone exchange is connected with SVEA by means of the AU connector 6 1 1 SVEA is connected to a phone When the phone is directly connected to SVEA by means of the AU connector all conversation will be made by means of the GSM network To make a voice call A voice call is originated by following the below procedure e Liftthe phone handset and check the presence of a dial tone The presence
17. ll Receiving a FAX DAY function disabled Receiving a fax is the same as if your analogue FAX was connected to a PSTN line but with a difference when receiving a fax SVEA automatically replies and stores the fax into its internal memory At the end of the connection it rings to the FAX connected to the PSTN connection point LINE in order to transfer the document After that SVEA erases the stored fax The fax storage capability allows SVEA to transfer the received document to the connected FAX up to 3 times in case of a printing error NOTE In case of problems receiving faxes originated from ISDN devices refer to Chapter 7 Troubleshooting POSSIO SVEA USER MANUAL Ce ee 000 0000 00 an 00 00000 0 0 0 0 00 0 0 0 0 0 0 0 04 DAY function The DAY function is intended to enable the operator to store incoming faxes into SVEAs internal memory without printing them The number of fax pages that can be stored varies depending upon the amount of text on each page and the type of resolution used 25 30 pages and 50 60 pages are respectively estimated for high and low resolution Use the following command to set up the function E n Command to enable disable the DAY function where n may be 1 Toenable the DAY function O Todisable the DAY function NOTE as soon as the function is disabled all stored faxes will be automatically printed E Command to delete all stored faxes and to free the internal m
18. ng Tone function type ATD555123456 NOTE if the modem is not forced to produce the Calling Tone and the preset digit El IS not entered the call you establish will be a voice call To receive a data call Connect the analogue modem to SVEA Make sure that the device is up and running Use a terminal emulation programme e g HyperTerminal on the PC connected with a modem In case of an incoming data call the ring message will appear on screen To establish a connection just type the ATA command Ce RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRERRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRERRRERREREEE E POSSIO SVEA USER MANUAL eee ee 0 0 000 000 00 an 0 00000 00 0 0 00 0 0 0 0 0 0 0 04 7 Troubleshooting 7 1 Setup Please ensure that all connections are securely attached and that the unit is powered on Make sure that you have inserted a SIM card and that you have activated your fax number with your operator 7 2 SIM card Make sure that you disabled the PIN number on your SIM card before inserting it into SVEA SVEA will also indicate that the PIN has not been disabled by the red LED flashing on off while the green LED is lit permanently You can disable the PIN number with a standard mobile phone 7 3 Printing a test page You can check whether the fax is correctly setup by printing a test page from the phone fax connected to the PSTN connection point Line of SVEA a test page will be printed if the entered v
19. nting can be set by typing the following command from your phone set fax connected to the PSTN connection point Line of SVEA ES Ed Ea a a n where n value js DISABLE report printing IN EACH mon transmission occured with success or failed 1 ENABLE report printing IN EACH SITUATION transmission occured with success or failed 2 ENABLE report printing ONLY if fax tranmission FAILS 3 ENABLE report printing first fax page ONLY if the fax transmission FAILED If the entered value is valid SVEA will generate a double tone as confirmation 6 3 Data Calls Make sure that an analogue modem up to V 90 is connected to SVEA via the AU connector 6 3 1 SVEA is connected with an analogue modem You can establish a data Internet connection by simply connecting an analogue modem with SVEAS AU connector When establishing a call some of the modems available on the market can communicate SVEA the intention to make a data call Communication occurs by means of a special dial tone called Calling Tone According to whether this function is available on your modem or not follow the instructions listed below to make a data call POSSIO SVEA USER MANUAL Ce ee ee ee 000 0 00 o ooo 00000 0000 00 0 0 0 0 0 0 0 0 4 Data call without forcing the Calling Tone function To be able to communicate SVEA the intention of making a data call type the user defined digit before the addressee s modem number the default value is
20. tion May 2006 Ce nn 0 0 00 000000 000 0 0 O 00 0 0 en 0 O 00 0000 00 00 000 O 00 00 0 000 00 00 0 0 00 0 000 0 pp 0 000 000 0 000 nn 0 00 0 0 0 0 0 0 0 0 0 0 0 0 4 POSSIO SVEA USER MANUAL Ce eee 00 00 an 0 00000 00 0 0 eee 0 0 0 0 4 Content 1 Foreword 3 6 Operating Modes 16 1 1 Declaration of Conformity 3 6 1 Voice Calls 16 1 2 Copyright 3 6 1 1 SVEA is connected to a phone 16 To make a voice call 16 2 Technical Specification 5 To receive a voice call 16 21 Physical dd 5 62 Fax Calls 16 a Exteel omen i 6 2 1 SVEA analogue fax 16 2 Consumption 5 ro aan 17 2 4 PSTN Connection Point 5 Receiving a fax 17 2 5 Modem Data Service 6 DAV union 18 2 6 Fax Service 6 To disable all fax reception 18 2 1 GSM Performance 6 Store amp Forward vs Pass thr 18 3 Warnings and Precautions 7 6 3 Data Calls 19 3 1 Safety Rules 7 6 3 1 SVEA analogue modem 19 3 2 Precautions 7 Printing Reports 19 3 3 Warnings Battery 8 Data Call 20 Establish a data call 20 4 Description 9 To receive a data call 20 4 1 Description of connectors 10 4 2 LED Status Report 11 Troubleshooting a 7 1 Setup 21 5 Get started 12 72 SIM card 21 5 1 Contents of the box 12 73 Printing a test page 21 5 2 Installation Guide 12 74 Camnoteend aia 21 5 2 1 Unscrew bottom 12 7 5 Cannot receive a fax 22 5 2 2 Insert SIM card 12 7 6 Cannot receive faxes ISDN 22 5 2 3 Backup Battery arrangement 13 7 7 Cannot establish a data 22 5 2 4 Antenna 14 5 2 5 Wall mounting 14 5
21. to the left e Once completed close SVEA again Reinsert the upper plastic cover and fasten the screws To power on the device simply plug the 230V AC connection into a wall plug NOTE If you plan to mount SVEA to the wall keep the cover off and continue reading at section 5 2 5 ATTENTION After having powered up the product if you detach it from the electrical network the battery will keep it running until it runs empty To power off the device completely detach the battery or press the reset key 5 2 4 Antenna The monopole antenna supplied with the product might fail to provide for an optimum reception of the RF signal in well defined operating conditions An external Omni directional antenna can be purchased as an accessory 5 2 5 Wall mounting IMPORTANT Before choosing the position for installation of the device evaluate the coverage of the GSM signal by using the functionality of the red LED or a mobile phone The backside of SVEA shows two holes properly shaped distance between the centres 185mm and arranged for wall fastening by using the screw anchors supplied CE POSSIO SVEA USER MANUAL ee ee 0000000 0 000 0 00 00 aC 00000 ee For wall fastening follow the steps here below 1 Insert the two screw anchors into the wall according to the specified distance between the centres 2 Fasten the screw with the mounting washer into the upper screw anchors 3 Hang the device onto the mounting wash
Download Pdf Manuals
Related Search
SVEA_user_manual_low..