Home

User`s Manual - Razberi Technologies

1. razberi technologies 1 2 7 2 1 System Under the tab lt System gt there are submenus including lt System gt lt Security gt lt Network gt lt DDNS gt lt Mail gt lt FTP gt lt HTTP gt lt Application gt lt Motion Detection gt lt Tampering gt SStorage Management lt Recording gt File Location lt lris Adjustment gt lt View Log File gt lt View User Information lt View Parameters gt lt Factory Default gt lt Software Version gt lt Software Upgrade gt and lt Maintenance gt NOTE The System configuration page is only accessible by the Administrator System The System Setting can be found under the path System gt System Host Name The name is for camera identification If alarm function refer to Application is enabled and is set to send alarm message by Mail FTP the host name entered here will display in the alarm message The maximum length of the Host Name is 30 characters Time Zone Select the time zone you are in from the drop down menu Enable Daylight Saving Time To enable DST please check the item and then specify time offset and DST duration The format for time offset is hh mm ss for instance if the amount of time offset is one hour please enter 01 00 00 into the field Sync With Computer Time Select the item and video date and time display will synchronize with the PC s Manual The Administrator can set video date time and day
2. view each user s privileges as shown below User 1 1 0 1 1 1 0 1 I O access Camera control Talk Listen refer to Security Therefore it denotes the user is granted privileges of I O access Camera control and Listen View Parameters The View Parameters function can be found under this path System gt View Parameter Click on this item to view the entire system s parameter setting such as Camera Settings Mask Information and Network Information 59 TM razberi technologies 7 2 18 7 2 19 60 Factory Default The Factory Default setting can be found under this path System gt Factory Default Users can follow the instructions on this page to reset the IP Camera to factory default setting if needed Set Default Click on the lt Set Default gt button to recall the factory default settings Then the system will restart in 30 seconds AN NOTE The IP address will be restored to default Reboot Click on the lt Reboot gt button and the system will restart without changing current settings Software Version The Software Version can be found under this path System gt Software Version The current software version is displayed in the software version page razberi technologies 7 2 20 Software Upgrade The Software Upgrade setting can be found under this path System gt Software Upgrade NOTE Make sure the upgrade software file is available before carrying out software upgrade The p
3. C 14 F 122 F Operating Temperature Humidity 10 to 90 no condensation Power Consumption 3 5 VV Weatherproof Rugged Camera IP66 CE FOG RoHS Compliant 2110 2 x 47 7 mm 2 4 3 x 1 9 in Optional 80 razberi technologies TM Appendix B Delete the Existing DC Viewer For users who have installed the DC Viewer in the PC previously please first remove the existing DC Viewer from the PC before accessing to the IP Camera Deleting the DC Viewer In the Windows Start Menu gt activate lt Control Panel gt and then double click on lt Add or Remove Programs gt In the lt Currently installed programs list select lt DCViewer gt and click on the button lt Remove gt to uninstall the existing DC Viewer Deleting Temporary Internet Files To improve browser performance it is suggested to clean up the all the files in the Temporary Internet Files The procedure is as follows Step 1 Click on the lt Tools gt tab on the menu bar and select lt Internet Options gt Step 2 Click on the lt Delete gt button under lt Browsing history gt section Then click on the lt Delete Files gt button under the lt Temporary Internet files gt section Step 3 A confirmation window will pop up Click on lt Yes gt to start deleting the files 81 TM razberi technologies Appendix C Setup Internet Security If ActiveX control installation is blocked please either set Internet security level to
4. 1280 x 1024 205 E gt we eno 08969 H 264 Only BNC SUPPORT 1920 x 1080 30fps somme omme gt oo gt we o o wonton cop o sen cop o Default Click on lt Save gt to confirm the setting razberi technologies Configuration Files Export Import To export import configuration files users can access the Maintenance page on the user friendly browser based configuration interface The Maintenance setting can be found under this path System Maintenance Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera Export Users can save the system settings by exporting the configuration file bin to a specified location for future use Click on the lt Export gt button and the popup File Download window will come out Click on lt Save gt and specify a desired location for saving the configuration file Upload To copy an existing configuration file to the IP Camera please first click on lt Browse gt to select the configuration file and then click on the lt Upload gt button for uploading 21 razberi technologies M 22 Menu Tree There are six main tabs including lt Home gt lt System gt lt Streaming gt lt Camera gt lt Pan Tilt gt and lt Logout gt on the Home Page Home Users can monitor live video of the targeted area System setting The a
5. SDHC card the card information such as the memory capacity and status will be shown at Device Information section For the memory card being successfully installed its status shall be shown at lt Device information gt section in the Storage Management page Device setting Click on the lt Format gt button to format the memory card Disk cleanup setting Users can enable automatic recordings cleanup by specifying the time and storage limits Recording List 55 TM razberi technologies 56 Each video file on the Micro SD SDHC card will be listed in the Recording list as shown below The maximum file size is 60 MB 60 MB per file When the recording mode is set as Always consecutive recording and the Micro SD SDHC card recording is also allowed to be enabled by events triggered once events occur the system will immediately implement events recording to the memory card Then the IP Camera will return to the regular recording mode after events recording e Remove To remove a file select the file first and then click on the lt Remove gt button e Sort Click on the lt Sort gt button and the files in the Recording list will be listed in name and date order NOTE The capital letter A M R T appears in the very beginning A of name denotes the sort of the recording A stands for Alarm M stands for Motion R stands for regular recording and T stands for Tampering e Download To open download a video clip sele
6. WDR Function The Wide Dynamic Range WDR function is for solving high contrast or changing light issues so that enhances better video display The WDR is adjustable from Low Mid to Hi Higher level of WDR represents wider dynamic range so that he IP Camera can catch a greater scale of brightness Click on lt V gt to confirm the new setting Noise Reduction The Noise Reduction Setting can be found under this path Camera gt Noise Reduction The IP Camera provides multiple lt Noise Reduction gt options for delivering optimized image quality especially in extra low light conditions Different level options for 3D Noise Reduction 3DNR include Low Mid and High Higher level of DNR generates relatively enhanced noise reduction The proprietary Smart Picture Quality SPQ video processing method could drastically minimum motion blur and reduce noise especially in low light environment The combination of SPO and 3DNR at different level further yields exceptional video performance in various conditions The Noise Reduction function is configurable with the following options 3DNR Low 3DNR Mid 3DNR Hi SPO SPO 3DNR Low SPO 3DNR Mid to SPQ 3DNR Hi Click on lt gt to confirm the new setting TV System Setting The TV System Setting can be found under this path Camera gt TV System 13 TM razberi technologies 1 5 1 9 1 14 Select the video format that matches the present TV system Click on lt V
7. and continuously regardless of zoom changes or any view changes Zoom AF Zoom Trigger AF son In this mode AF is activated at the time when zoom is adjusted Push AF Pust AF The one push AF function is for fixing the focus on the target in a shot using AF Once click on the button AF will be implemented Reset button Ressel Click on the lt Reset gt button and the camera lens will be calibrated at full wide end and infinity focus at once 25 TM razberi technologies 7 1 2 26 Function Differences between Models Below table tells the model differences you will find on the home page V indicates functions can be found on the model you bought A F each indicates a model type a b indicate different lens as shown below A Full HD Multiple Streams Box IP Camera B 10x 18x Zoom AF IP Camera C Full HD Multiple Streams Vandal Proof Fixed Dome IP Camera D Full HD Multiple Streams Lightweight Fixed Dome IP Camera E Full HD Multiple Streams IR Bullet IP Camera F Full HD Multiple Streams Compact Fixed Dome IP Camera a Vari focal Lens b Motorized Lens c Fixed focal Lens Model Function me EE KA Digital Zoom Control See LI TIVE i Is J garn it EN eee EN Video CE Pause Restart ET e Zoom Adjustment Manual Focus Adjustment Auto Focus Adjustment TelerWide NO fen DH KN Tele Steps Wide NeariFar Far Near Steps Far Roar Se KE
8. default or change ActiveX controls and plug ins settings Internet Security Level Default Step 1 Step 2 Step 3 Step 4 the Start the Internet Explorer IE Click on the lt Tools gt tab on the menu bar and select lt Internet Options gt Click on the lt Security gt tab and select lt Internet gt zone Down the page click on the lt Default Level gt button and click on lt OK gt to confirm setting Close the browser window and restart a new one later to access the IP Camera ActiveX Controls and Plug ins Settings Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 82 Repeat Steps 1 3 of the previous section above Down the page click on the SCustom Level gt button to change ActiveX controls and plug ins settings The Security Settings window will pop up Under lt ActiveX controls and plug ins gt set ALL items as listed below to lt Enable gt or lt Prompt gt Please note that the items vary by IE version ActiveX controls and plug ins settings Allow previously unused ActiveX controls to run without prompt Allow Scriptlets Automatic prompting for ActiveX controls Binary and script behaviors Display video and animation on a webpage that does not use external media player Download signed ActiveX controls Download unsigned ActiveX controls Initialize and script ActiveX controls not marked as safe for scripting 1 2 3 4 5 6 T 8 9 Run ActiveX contr
9. gt button when complete UPnP The UPnP setting can be found under this path System gt Network gt UPnP UPnP Setting Enable UPnP When the UPnP is enabled whenever the IP Camera is presented to the LAN the icon of the connected IP Cameras will appear in My Network Places to allow for direct access NOTE To enable this function please make sure the UPnP component is installed on your computer Please refer to Install UPnP components for UPnP component installation procedure Enable UPnP port forwarding When the UPnP port forwarding is enabled the IP Camera is allowed to open the web server port on the router automatically NOTE To enable this function please make sure that your A router supports UPnP and it is activated Friendly name Set the name for the IP Camera for identity razberi technologies 7 2 4 7 2 5 DDNS The DDNS setting can be found under this path System gt DDNS Dynamic Domain Name System DDNS allows a host name to be constantly synchronized with a dynamic IP address In other words it allows those using a dynamic IP address to be associated to a static domain name so others can connect to it by name Enable DDNS Check the item to enable DDNS Provider select one DDNS host from the provider list Host name Enter the registered domain name in the field Username E mail Enter the username or e mail required by the DDNS provider for authentication Password Key Enter the p
10. gt to confirm the new setting Pan Tilt Under the tab sPan Tilt gt there are submenus including lt Preset gt lt Sequence gt and lt Pan Tilt Control gt NOTE Pan Tilt function is only available for 10x 18x Zoom AF IP Camera and Box Camera DC12V AC24V PoE Model With RS 485 support the IP Camera is capable of working with a Pan Tilt Head for pan and tilt control Before implementing pan tilt control please ensure the Pan amp Tilt Head is correctly connected to the IP Camera s RS 485 port Pin Definition for IP Camera s RS 485 Port Preset The Preset Setting can be found under this path Pan Tilt gt Preset NOTE Before setting this function users must enable the Pan Tilt Control first Please refer to Pan Tilt Control for more details There are up to 127 preset points that can be set in the Preset setup page Please follow the steps below to set and run preset points Preset Points Setup Step 1 Move the camera to the desired position by moving the mouse cursor onto the screen one left click on mouse and then dragging the red arrow to panitilt Users may adjust the zoom position as well Step 2 Once a Preset Point is defined please assign a number between 1 and 127 and enter it into the input field razberi technologies M Step 3 Click on the lt v gt button to save the defined preset point 15 TM razberi technologies 1 5 2 16 Preset Run Type the Preset Point number into
11. manually Entry format should be identical with that shown next to the enter fields 21 razberi technologies M 28 Sync with NTP server Network Time Protocol NTP is an alternate way to synchronize your camera s clock with a NTP server Please specify the server you wish to synchronize in the enter field Then select an update interval from the drop down menu For further information about NTP please refer to the web site www ntp org razberi technologies M 1 2 2 7 2 2 1 Security The Security setting can be found under this path System gt Security Click on the Security category there will be a drop down menu with tabs including lt User gt lt HTTPS gt lt IP Filter gt and lt IEEE 802 1X gt User The User setting can be found under this path System gt Security gt User Admin Password Change the administrator s password by inputting the new password in both text boxes The input characters numbers will be displayed as dots for security purposes After clicking on lt Save gt the web browser will ask the Administrator for the new password for accessing The maximum length of the password is 14 characters AN NOTE The following characters are valid A Z a z 0 9 H 8 amp Q Add user Type the new user s name and password and click on lt Add gt to add the new user User name can be up to 16 characters and the maximum length of the password is 14 characters The new user will be displayed i
12. number being set For example if the setting is up to 10 the file name will start from 00 end at 10 and then start all over again e Overwrite The original image in the FTP site will be overwritten by the new uploaded file with a static filename Save After complete all the settings mentions above please click on lt Save gt button to save all the settings in this page Motion Detection The Motion Detection setting can be found under this path System gt Motion Detection Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area reaches exceeds the determined sensitivity threshold value 45 razberi technologies 46 In the Motion Detection setting page there is a frame Motion Detection Window displayed on the Live Video Pane as the figure below The Motion Detection Window is for defining the motion detection area To change the size of the Motion Detection Window move the mouse cursor to the edge of the frame and draw it outward inward Moving the mouse to the center of the frame can shift the frame to the intended location Up 10 Motion Detection Windows can be set Click on the lt add gt button under the Live Video Pane to add a Motion Detection Window To cancel a Motion Detection Window move the mouse cursor to the selected Window and click on the lt delete gt button If Motion Detection function is activated the pop off window Motion
13. rotating the mouse wheel for zoom in out and drag the mouse into any direction Screen Size Adjustment lt 1 12 Image display size can be adjusted to x1 2 and full screen Talk button KE 8 on off Talk function allows the local site to talk to the remote site Click on the button to switch it to on off Please refer to Security Add user gt Talk Listen for further details This function is only open to User who has been granted this privilege by the Administrator Speaker button 4 on off Click on the lt Speaker gt button to mute activate the audio AN NOTE This function is only available for User vvho has granted this privilege by the Administrator Snapshot button M Click on the button and the JPEG snapshots will automatically be saved in the appointed place The default place of saving snapshots is C To change the storage location please refer to File Location for further details AN NOTE For users with Windows 7 operating system it is required to log on as an Administrator to implement the Snapshot function 23 TM razberi technologies 24 Video Streaming Pause Restart button LI k pause restart Click on the lt stop gt button to disable video streaming the live video will be displayed as black Click on the lt restart gt button to show the live video again Web Recording button ca e on off Click on the lt Recording gt button and the Live View through the web browsing
14. the Preset field click on the ia button and the camera will turn to the appointed point Sequence The Sequence Setting can be found under this path Pan Tilt gt Sequence The Sequence function supports totally eight Sequence Lines each Sequence Line consists of up to 64 Preset Points Please refer to the instructions below to program a Sequence Line AN NOTE Before setting this function users must pre define at least two Preset Points Sequence Setting e Sequence Line Please select the number of Sequence Line to be set from the drop down list e Sequential Preset Points Setting Please setup each Preset Point of the programmed Sequence Line in order assigning a Preset Point from the NO list for the specified number of Preset Point and entering Dwell Time 0 255 sec into the corresponding fields e Sequence Reset To reset the sequence setting of each line please click on the lt Reset gt button in the right top corner of the setup page And then click on the lt Set gt button on the left to refresh the page in order to enter the new settings When finishing the sequential Preset Points setting please click on the button lt Save gt in the top of the Sequence setting menu Sequence Run Select the specified Sequence Line from the drop down list click on the FR button and then the camera will start moving forward each scene sequentially as programmed razberi technologies M 7 9 3 To view the camera executin
15. 0090 razberi 825 technologies r ra Full HD Multi Stream Compact Dome IP Camera LP200 1 val E al User s Manual Ver 4 17 soo Ss p Table of Contents OI V Va S 3 FANS nr 3 1 2 Package SEE 4 1 3 DIMensions arrrnrvarrnanrnarvnnrnanrnarnnnrnannnannnrnannnannnnenanenannnernannnannnnnnanenannneennnennnnneennnsnnen D 1 4 OL 0 I 11 030 aaa anen nne iken eee ene e eee ee ee e eee eee aaa 6 Camera Cabling aa SR 7 2 1 1 Indoor Camera arrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnennunennnnennnnennnnennusennusennnsennnsennnne 7 NTN FEN 9 ACCESS NE 10 Setup Video RESOU O roie Aaaa aA 14 Configuration Files Export Import r snnnnnrernnnnnnnnennnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnennnnnnnnnennnnnnnnr 21 Men J aa i e 22 7 1 Home Pader 23 7 1 1 Function Items on Home Page 1 aaa 23 7 1 2 Function Differences between Models aaaaaaa kaaa kakaa kakaa kakaa kaaa 26 7 2 System 2 0 0 cecccsccceseeccseeccseeccseeceseeceseeceseeseeeseseeseaeeseueeseeeseeeeeaeessseeseseeeseueeseusesseesseeesees 27 7 2 1 ST 27 T 2 2 SE CU ty aaa kakaa 29 7 2 3 NNN 34 7 2 4 DONG o e dd dtd dd td dd E 39 7 2 5 MA 39 7 2 6 PP 40 T 2 1 TN 40 7 2 8 Application Compact Fixed Dome Excluded aaa aaa nana aaa ann anen enen eneve neve meren 41 7 2 9 fo te eB ici tei seen 45 7 2 10 Tampering eee cece ceeeceeeece cece koe oka kaaa 52 7 2 11 Storage Management Local Recording aaa kakaa k
16. 2M Real time 1 2 7 Progressive CMOS 2M 1920 H x 1080 V 0 1 lux F1 5 1 1 10000 sec Manual AWB ATW F1 5 f 4 0 mm 78 Operation Video Compression Video Streaming Resolution Contrast White Balance Hue Image Setting Backlight Compensation Digital Zoom WDR 3D Noise Reduction Motion detection Privacy Mask Privacy Mask Type Tampering Alarm One way Audio H 264 MJPEG Simultaneous H 264 1080p 25 30 fps MJPEG D1 25 30 fps Simultaneous H 264 1080p 13 15 fps MJPEG 720p 25 30 fps Simultaneous H 264 1080p 25 30 fps H 264 D1 25 30 fps Simultaneous H 264 1080p 13 15 fps H 264 720p 25 30 fps Full HD 1080p SXGA HD720p XGA SVGA D1 VGA CIF Manual Auto Manual Manual Manual Auto Manual Manual Manual On Off Support On Off On Off On Off On Off Color On Off Mic in O razberi technologies NA Compression G 711 G 726 Event Notification HTTP FTP SMTP English French German Italian Korean Simplified Chinese Traditional Multiple Languages Chinese Russian IPv4 v TCP IP UDP RTP RTSP HTTP HTTPS ICMP FTP SMTP Protocol DHCP PPPoE UPnP IGMP SNMP QoS and ONVIF Password Levels User and Administrator Internet Browser Internet Explorer 6 0 Chrome Firefox Safari z Mechanical Lens Mounting M12 Board Lens RJ 45 Connectors Micro SDHC 32GB support General 10 C 50
17. A signed certificate for implementing lt HTTPS gt To use HTTPS on the IP Camera a HTTPS certificate must be installed The HTTPS certificate can be obtained by either creating and sending a certificate request to a Certificate Authority CA or creating a self signed HTTPS certificate as described below Create Self signed Certificate Before a CA issued certificate is obtained users can create and install a self signed certificate first Click on lt Create gt button under Create self signed certificate and provide the requested information to install a self signed certificate for the IP Camera Please refer to the last part of this section Provide the Certificate Information for more details NOTE The self signed certificate does not provide the same high level A of security as when using a CA issued certificate razberi technologies Install Signed Certificate Click on the lt Create Certificate Request gt button to create and submit a certificate reguest in order to obtain a signed certificate from CA Provide the reguest information in the create dialog Please refer to the following Provide the Certificate Information for more details When the reguest is complete the subject of the Created Reguest will be shown in the field Click on lt Properties gt below the Subject field copy the PEM formatted request and send it to your selected CA When the signed certificate is returned install it by uploading th
18. H 264 3 GOV Length 30 H 264 4 GOV Length 30 Save H 264 Profile H 264 1 main profile ti H 264 2 Main profile v H 264 3 Main profile vi H 264 4 Main profile v Save Click on lt Save gt to confirm the setting razberi technologies M 2M Model Video Format Under Video Resolution section select a preferred resolution setting The available Video Resolution for MJPEG amp H 264 format includes H 264 H 264 H 264 2 BNC SUPPORT 1280 x 720 30fps me 1024 x 768 203 wwo o zr ormo o wo O cro TT Cc TT K NN RENEE za so nj RENE E om SSS mows RENE reos RENE omeo TT 1280 x 720 30fps za aso aj RENE so aso nj TT rr SS zere ej ex co aj TT owo RENEE swo C mwmw TT 800 x 600 30fps wowo EE mom gt 1920 x 1080 15fps 15 TM razberi technologies 720 x 480 30fps 640 x 480 30fps m 640 x 480 30fps 352 x 240 30fps a 352 x 240 30fps H 264 MJPEG MJPEG BNC SUPPORT oxra ENE Kr sone gt KE ll Po ono mem JI ean 1024 rs RR KE RENE oxe ENE ruan NENE ET RENE awo OJ mmen gt gt oaeeo p gt ooe _ 1280 x 720 30fps mw ENA oem 1 gt same NENE hon oem 1 mono s re gt ET ll room 800 x 600 30fps ono ET U 1920 x 1080 15fps razberi technologies 720 x 480 30fps 640 480 Goo 640 x 480 30fps 352 x 240 30fps 352 x 240 30fps MJPEG On
19. Select lt Upload during the trigger active gt to make the images keep being uploaded to E mail during the trigger active until the event stops Set the Image frequency as the upload frame rate The setting range is from 1 frame to 15 frames AN NOTE Make sure SMTP configuration has been completed Refer to Mail for further details Send HTTP notification Check this item select the destination HTTP address and specify the parameters for event notifications by lt Motion Detection gt triggered When an alarm is triggered the notification can be sent to the specified HTTP server For instance if the custom parameter is set as action 1 amp group 2 and the HTTP server name is http 192 168 0 1 admin php the notification 49 razberi technologies M 50 will be sent to HTTP server as http 192 168 0 1 admin php action 1 amp group 2 when alarm is triggered razberi technologies M File Name The uploaded images filename format can be set in this section Please select the one that meets your requirements Save Click on the lt Save gt button to save all the Motion Detection settings mentioned above 51 TM razberi technologies 7 2 10 Tampering 52 The Tampering setting can be found under this path System Tampering Tempering Alarm function helps the IP Camera against tampering such as deliberate redirection blocking paint spray and lens cover etc through video analysis and reaction to such e
20. akaa kakaa kaaa 55 7 2 12 Recording Local RECOrdING ccccccceecceeecceeeeeeeeeeaeeeeseeeeseeeeeeeesseeesseeees 57 7 2 13 File Location Snapshots and Web Recording cccscccceeeeseeeeseeeeeeees 58 7 2 14 Iris Adjustment Fixed Focal Lens Excluded nana aaa aaa nana nana aaa kaaa 58 SS VM 58 7 2 16 View User Information 1 aaa nene eee eee eee kakaa kakaa 59 1207 VEN ParaMEe GT S Larsnes Ae eee 59 1218 Factory Defaull ARA 60 Ta SONWaTE NV SN 60 7 2 20 Software VUNNET see et 61 7 221 MAINTENANCE ese cent dh h t e 62 1 razberi technologies 7 3 NNN 63 7 3 1 Video Format Video Resolution and Rotate Type ccccceeeeeeeeeeeeeees 63 1 3 2 Video Compression aaa aaa kaaa kakaa aaa kaaa kaaa kakaa ee pene aaa 64 1320 Video OCX PrOtocOI aaa aaa nanen ake eee eee eee eee kakaa kaaa 65 7 3 4 Video Frame Ratte ccccccccsscccececeeeceeeceeecseesaueceueesacecseeceeeseueesaeessessaeesees 66 199 Video Mask OE 66 7 3 6 Audio Audio Mode and Bit Rate Settings rrrorrrrnnrrrrnnrrrnnrennrrrrnnrrrnnennnn 67 7 4 G ici M EP 68 7 4 1 Fres ve 68 7 4 2 White Balance Seming EEE 70 7 4 3 Fe SITTE Va 41 7 4 4 PN 71 7 4 5 PAZ 12 T 4 6 IR Function Compact Fixed Dome Excluded Beale aa a a kakaa kaka aaa kaaa 12 1 4 1 WDR Function kakaa 13 7 4 8 NOISE Reduction pan ARA 13 7 4 9 TV System Setting aaa 73 1 5 Pan Tilt aaa aaa Re ee ee ee eee ene eee e
21. and lt TV System gt Exposure Setting The Exposure Setting can be found under this path Camera gt Exposure The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening the amount of exposure by the sensor shutter speed and other exposure parameters With this item users can define how the Auto Exposure function works Each exposure mode is specified as follows Auto Iris Fixed Focal Lens Excluded In this mode the exposure gives priority to the auto iris The minimum shutter speed can be set from 1 1 1 5 to 1 30 1 25 sec AGC Auto Gain Control will function automatically according to the light conditions of the subject NOTE This function is not available for Fixed Focal Lens Models Auto Shutter Mode This function is to control the shutter speed and adjust the iris automatically according to the light intensity It is also effective if a fixed iris lens is being used The minimum shutter speed range is configurable from 1 1 1 5 to 1 500 1 425 sec Shutter Priority Mode This function is to set the shutter speed at a specified speed The range is configurable from 1 30 1 25 to 1 500 1 425 sec razberi technologies Manual Mode e Fixed Shutter Mode In this mode fixed shutter speed could be selected from the dropdown menu The shutter speed range is from 1 10000 to 1 1 1 5 sec with 19 18 options Users could select suitable shu
22. assword or key required by the DDNS provider for authentication Mail The Mail setting can be found under this path System gt Mail The Administrator can send an e mail via Simple Mail Transfer Protocol SMTP when motion is detected SMTP is a protocol for sending e mail messages between servers SMTP is a relatively simple text based protocol where one or more recipients of a message are specified and the message text is transferred Two sets of SMTP can be configured Each set includes SMTP Server Account Name Password and E mail Address settings For SMTP server contact your network service provider for more specific information 39 TM razberi technologies 7 2 6 1 2 7 40 FTP The FTP setting can be found under this path System gt FTP The Administrator can set as sending alarm message to a specific File Transfer Protocol FTP site when motion is detected Users can assign alarm message to up to two FTP sites Enter the FTP details which include server server port user name password and remote folder in the fields Click on lt Save gt when finished HTTP The HTTP setting can be found under this path System HTTP A HTTP Notification server can listen for notification messages from IP Cameras by triggered events Enter the HTTP details which include server name for instance http 192 168 0 1 admin php user name and password in the fields lt Alarm gt triggered and lt Motion Detection gt noti
23. ath Streaming gt Video Frame Rate Video frame rate is for setting the frames per second fps if necessary MJPEG H 264 1 H 264 2 Frame Rate The default setting of MJPEG H 264 1 H 264 2 Frame Rate is 30 fps the setting range is from 1 to 30 Click on lt Save gt to confirm the setting AN NOTE Lower frame rate will decrease video smoothness Video Mask The Video Mask setting can be found under this path Streaming gt Video Mask Active Mask Function e Add a Mask Check a Video Mask checkbox and a red frame will come out in the Live Video pane at the right side Use the mouse to drag and drop to adjust the mask s size and place it on the target zone AN NOTE It is suggested to set the Video Mask twice bigger than the object e Cancel a Mask Uncheck the checkbox of the Video Mask meant to be deleted and the selected mask vvill disappear from the Live Video pane instantly Mask Setting e Mask color The selections of Mask color include red black white yellow green blue cyan and magenta Click on lt Save gt to confirm the setting razberi technologies TM 7 3 6 Audio Audio Mode and Bit Rate Settings The Audio Mode setting can be found under this path Streaming gt Audio In the Audio page the Administrator can select one transmission mode and audio bit rate Transmission Mode e Full duplex Talk and Listen simultaneously In the Full duplex mode the local and remote sites can communicate with
24. chnologies razberi technologies M System Reguirements To perform the IP Camera via web browser please ensure your PC is in good network connection and meet system reguirements as described below System Reguirement 1 Intel Pentium M 2 16 GHz or Intel Core 2 Duo 2 0 Personal Computer GHz 2 2 GB RAM or more Operating System Windows VISTA Windows XP Windows 7 Web Browser Microsoft Internet Explorer 6 0 or later Firefox Chrome Safari Network Card 10Base T 10 Mbps or 100Base TX 100 Mbps operation ActiveX control plug in for Microsoft IE 9 razberi technologies M 10 Access Camera For initial access to the IP Camera users can search the camera through the installer program DeviceSearch exe which can be found in DeviceSearch folder in the supplied CD Device Search Software Setup Step 1 Double click on the program Device Search exe After its window appears click on the Device Search button on the top side Step 2 The security alert window will pop up Click on lt Unblock gt to continue Device Search Step 3 Step 4 Step 5 Click on Device Search again and all the finding IP devices will be listed in the page The IP Camera s default IP address is 192 168 0 250 Double click or right click and select lt Browse gt to access the camera directly via web browser Razberi Discovery Tool 1 0 0 1 m 01 xi Search Method 7 Local Broadcast 2 device s f
25. ck on lt gt to confirm the new setting razberi technologies TM 7 4 3 7 4 4 Picture Adjustment The Picture Adjustment can be found under this path Camera gt Picture Adjustment Brightness Users can adjust the images brightness by adjusting the item Please select ranging from 12 to 13 To increase video brightness select a bigger number Click on lt V gt to confirm the new setting Sharpness Increasing the sharpness level can make the image looked sharper especially enhance the object s edge Please select ranging from 0 to 15 Click on lt V gt to confirm the new setting Contrast Camera image contrast level is adjustable please select ranging from 6 to 19 Click on lt gt to confirm the new setting Saturation Camera image saturation level is adjustable please select ranging from 6 to 19 Click on lt gt to confirm the new setting Hue Camera image hue level is adjustable please select ranging from 12 to 13 Click on lt gt to confirm the new setting Backlight The Backlight Setting can be found under this path Camera gt Backlight The Backlight Compensation function prevents the center object from being too dark in surroundings where excessive light is behind the center object Click on lt V gt to confirm the new setting 71 razberi technologies 1 4 5 7 4 6 12 Digital Zoom The Digital Zoom Setting can be found under this path Camera gt Digital Zo
26. conds Select lt Upload during the trigger active to make the images keep being uploaded to E mail during the trigger active until the alarm is released Set the Image freguency as the upload frame rate The setting range is from 1 frame to 15 frames AN NOTE Make sure SMTP configuration has been completed Refer to Mail for further details Send HTTP notification Check this item select the destination HTTP address and specify the parameters for event notifications by lt Alarm gt triggered When an alarm is triggered the notification can be sent to the specified HTTP server For instance if the custom parameter is set as action 1 amp group 2 and the HTTP server name is http 192 168 0 1 admin php the notification will be sent to HTTP server as http 192 168 0 1 admin php action 1 amp group 2 when alarm is triggered 43 razberi technologies 44 razberi technologies M 1 2 9 File Name Enter a file name in the blank ex image jpg The uploaded images file name format can be set in this section Please select the one that meets your requirements e Add date time suffix File name imageYYMMDD HHNNSS XX jpg Y Year M Month D Day H Hour N Minute S Second X Sequence Number e Add sequence number suffix no maximum value File name imageXXXXXXX jpg X Sequence Number Add sequence number suffix limited value File Name imageXX jpg X Sequence Number The file name suffix will end at the
27. ct the file first and then click on the lt download gt button below the Recording list field The selected file window will pop up Click on the AVI file to directly play the video in the player or download it to a specified location razberi technologies M 7 2 12 Recording Local Recording The Recording setting can be found under this path System Recording In the Recording setting page users can specify the recording schedule that fits the present surveillance requirement Recording Schedule Disable Always Only during time frame Sun Man Tue Wed Thu Start time oo 00 Duration 00 00 Save Activating Micro SD SDHC Card Recording Two types of schedule mode are offered Always and Time Frame setting Users can setup the time frame to fit the recording schedule or choose lt Always gt to activate Micro SD SDHC Card Recording all the time Please click on the lt Save gt button for confirming the schedule mode Terminating Micro SD SDHC Card Recording select lt Disable gt to terminate the recording function 91 TM razberi technologies 7 2 13 7 2 14 7 2 15 58 File Location Snapshots and Web Recording The File Location setting can be found under this path System File Location Users can specify a storage location on the PC or in the hard drive for the snapshots and live video recording The default setting is C Once confirm the setting click on Save and all the
28. d the listed IP addresses IPv4 will be allowed denied access to the IP Camera Select lt Allow gt or lt Deny gt from the drop down list and click on the lt Apply gt button to determine the IP Filter behavior Add Delete IP Address Input the IP address and click on the lt Add gt button to add a new filtered address The Filtered IP Addresses list box shows the currently configured IP addresses Up to 256 IP address entries may be specified To remove an IP address from the list please select the IP and then click on the lt Delete gt button razberi technologies 7 2 2 4 IEEE 802 1X The IEEE 802 1X setting can be found under this path System gt Security gt IEEE 802 1X The IP Camera is allowed to access a network protected by 802 1X EAPOL Extensible Authentication Protocol over LAN Users need to contact with the network administrator for gaining certificates user IDs and passwords CA Certificate The CA certificate is created by the Certification Authority for the purpose of validating itself Upload the certificate for checking the server s identity Client Certificate Private Key Upload the Client Certificate and Private Key for authenticating the IP Camera itself Settings e Identity Enter the user identity associated with the certificate Up to 16 characters can be used e Private Key Password Enter the password maximum 16 characters for your user identity Enable IEEE 802 1X Check
29. dministrator can set host name system time root password network related settings etc Further details will be interpreted in chapter System Streaming setting The administrator can modify video resolution and rotate type and select audio compression mode in this page Camera setting Users can adjust various camera parameters including lt Exposure gt lt White Balance gt lt Picture Adjustment gt lt Backlight gt SDigital Zoom lt IR Function gt lt WDR Function gt lt Noise Reduction gt and STV System gt Pan Tilt setting Users can activate the pan tilt function and select the RS 485 protocol which the Pan Tilt Head uses in the lt Pan Tilt Control gt page NOTE Pan Tilt function is only available for 10x 18x Zoom AF IP Camera and Box Camera DC12V AC24V PoE Model Logout Click on the tab to re login the IP Camera with another username and password razberi technologies 7 1 7 1 1 Home Page Click on the tab lt Home gt to access the Home Page There are several function buttons on the Home page Detailed information of each item is as described in the following chapter Function Items on Home Page Multiple Languages Support Multiple languages are supported including German English French Italian Korean Simplified Chinese Traditional Chinese Russian etc for the viewer window interface Digital Zoom Control In the full screen mode users can implement digital PTZ by
30. e contains the following items listed below Self tapping Plastic Anchors Security Torx screvvs x3 x3 Indoor Cameral Rugged Camera with Cable substrate material installation such as wood For other installation environment such as cement wall it is required to pre drill and use plastic anchors before fastening the supplied self tapping screw on the wall AN NOTE The type of the supplied self tapping screws is mainly for softer razberi technologies M 1 3 Dimensions The IP Camera s dimensions are shown below 110 2 5 razberi technologies 1 4 Connectors The diagram below shows the IP Dome Camera s reset button and various adjusting screws Definition for each will be given as follows DEE 12 3 435 Designation Description Restore to default setting press the Reset Button l button with a proper tool 2 Lens Rotate the lens right left to adjust focus 3 Focus Fixed Screw Loosen the screw to adjust the lens LA Tilt Fixed Screw Loosen the screw to adjust tilt angle 5 Microphone For Audio VV 6 Micro SD Card Slot For video recording storage razberi technologies M 2 Camera Cabling Please follow the instructions below to complete IP Camera connection 2 1 1 Indoor Camera PoE Connection Connect the one end of the Ethernet cable to the network port on the camera and the other end to Power Sourcing Eguipment PSE like hubs or routers T razberi te
31. e signed certificate Provide the Certificate Information To create a Self signed HTTPS Certificate or a Certificate Request to CA please enter the information as requested fee sat stares Grini Croate Grin Request State or Pro Organization PN Organizational Uni 1 NN Common Name VP y Valid Day e Country Enter a 2 letter combination code to indicate the country the certificate will be used in For instance type in US to indicate United States e State or province Enter the local administrative region e Locality Enter other geographical information e Organization 31 TM razberi technologies 7 2 2 3 32 Enter the name of the organization to which the entity identified in Common Name belongs Organization Unit Enter the name of the organizational unit to which the entity identified in Common Name belongs Common Name Indicate the name of the person or other entity that the certificate identifies often used to identify the website Valid days Enter the period in days 1 9999 to indicate the valid period of certificate Click on lt OK gt to save the Certificate Information after complete IP Filter The IP Filter setting can be found under this path System gt Security gt IP Filter Using the IP filter access to the IP Camera can be restricted by denying allowing specific IP addresses Enable IP Filter Check the box to enable the IP Filter function Once enable
32. each other simultaneously i e both sites can speak and be heard at the same time e Half duplex Talk or Listen not at the same time In the Half duplex mode the local remote site can only talk or listen to the other site at a time e Simplex Talk only In the Talk only Simplex mode the local remote site can only talk to the other site AN NOTE This function is not available for Compact Fixed Dome e Simplex Listen only In the Listen only Simplex mode the local remote site can only listen to the other site e Disable Select the item to turn off the audio transmission function Server Gain Setting Set the audio input output gain levels for sound amplification The audio gain values are adjustable from 1 to 6 The sound will be turned off if the audio gain is set to Mute Bit Rate Selectable audio transmission bit rate include 16 kbps G 726 24 kbps G 726 32 kbps G 726 40 kbps G 726 uLAW G 711 and ALAW G 711 Both uLAW and ALAW signify 64 kbps but in different compression formats Higher bit rate 67 TM razberi technologies 1 4 1 4 1 68 will let higher audio quality and require bigger bandwidth Click on lt Save gt to confirm the setting Camera Under the tab lt Camera gt there are submenus including lt Exposure gt lt White Balance gt lt Picture Adjustment gt lt Backlight gt lt Digital Zoom gt lt IR Function gt lt WDR Function gt lt Noise Reduction gt
33. ee ee eee eee enet e eee eee ee eee ene eee teke eee eee eee tee eee eee eee eee eee eee eee 14 7 9 1 PS 14 7 5 2 SEQUENCE ne 76 7 9 3 FUNN 77 7 6 LQG OUI e mn nn mn e ana 78 Appendix A Technical Specifications na auuunaanan nana seen no s ene eren nese ann 79 Appendix B Delete the Existing DC Viewer rrnnnunnnnnnnvnnnnnnnnennnnnnnnnnnnnnennnnnnnennnnnnvennnnnnernnnnnuennnn 81 Appendix C Setup Internet Security rrrrrnnnnnnnnvvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnennnnnnnnnnennnnnnnnnennnnnnn 82 Appendix E Install UPnP Components nuuennnnnnnnnvnnnnnnnnnvnnnnnnnnnnnnnnnnnnernnnnnnnnvennnnnnnnnnnnnnnnnnnennnnnnnnn 83 razberi technologies M 1 1 Overview Supported with both H 264 and MJPEG standard the product series not only features in superior Full HD resolution for real time streaming at 25 30 fps but also supplies a full D1 720p real time Analog stream With more computing power the IP Camera will provide more flexibility for users and system managers Features Progressive Scan CMOS Sensor Dual Streams Full HD real time D1 real time H 264 and MJPEG compression Motion Detection Privacy Masks WDR Smart Picture Quality 3DNR Tampering Alarm Day Night ICR Micro SD support Weatherproof Dongle Cable Optional Weatherproof IP66 international Micro SD support Optional Security Torx against tampering ONVIF Support 3 razberi technologies M 1 2 Package Contents Please check the packag
34. factor is 35 the setting range is from 1 to 70 H 264 1 H 264 2 bit rate The default setting of H 264 1 H 264 2 is 4096 1024 kbps the setting range for H 264 1 is from 64 to 8192 kbps and for H 264 2 is from 64 to 2048 kbps razberi technologies 1 3 3 Display Compression Information Users can also decide whether to display compression information on the Home page CBR Mode Setting The CBR Constant Bit Rate mode could be the preferred bit rate mode if the bandwidth available is limited It is important to take account of image quality while choosing to use CBR mode Click on lt Save gt to confirm the setting Video OCX Protocol The Video OCX Protocol setting can be found under this path Streaming gt Video OCX Protocol In the Video OCX protocol setting page users can select RTP over UDP RTP over TCP RTSP over HTTP or MJPEG over HTTP for streaming video over the network In the case of multicast networking users can select the Multicast mode Video OCX protocol setting options include e RTP over UDP RTP over RTSP TCP RTSP over HTTP MJPEG over HTTP e Multicast Mode Enter all required data including SMulticast IP Address gt SH 264 Video Port gt lt MJPEG Video Port gt SAudio Port and lt TTL gt into each blank Click on lt Save gt to confirm the setting 65 TM razberi technologies 7 3 4 7 3 9 66 Video Frame Rate The Video Frame Rate setting can be found under this p
35. fications can be sent to the specified HTTP server Click on lt Save gt when finished Please refer to Application gt Send HTTP notification Motion Detection for HTTP Notification settings razberi technologies M 7 2 8 Application Compact Fixed Dome Excluded The Application setting can be found under this path System gt Application The IP Camera equips one alarm input and one relay output for cooperating with alarm system to catch events images Refer to alarm pin definition below to connect alarm devices to the IP Camera if needed Alarm Pin Definition Please refer to User s Manual for Alarm Pin Definition to connect the alarm devices Alarm Switch The Administrator can enable or disable the alarm function Alarm Type Select an alarm type SNormal close or SNormal open that corresponds with the alarm application Alarm Output Define alarm output signal lt high gt or lt low gt as the normal alarm output status according to the current alarm application Triggered Action Multi option The Administrator can specify alarm actions that will take when the alarm is triggered All options are listed as follows e Enable Alarm Output Select the item to enable alarm relay output e IR Cut Filter Select the item and the camera s IR cut filter ICR will be removed on or blocked off when alarm input is triggered AN Note The IR Function Refer to IR Function could not be set as lt Auto gt m
36. for one minute before continuing Step 4 Click on the SDevice Search button to search all the devices Then select the IP Camera with the correct MAC address Double click on the IP Camera and the login window will pop up Step 5 Enter User name and Password to access the IP Camera Installing DC Viewer Software Online For the initial access to the IP Camera a client program DC Viewer will be automatically installed to your PC when connecting to the IP Camera If the Web browser doesn t allow DC Viewer installation please check the Internet security settings or ActiveX controls and plug ins settings refer to Section Setup Internet Security to continue the process The Information Bar just below the URL bar may come out and ask for permission to install the ActiveX Control for displaying video in browser Right click on the Information Bar and select lt Install ActiveX Control gt to allow the installation 11 razberi technologies M The download procedure of DC Viewer software is specified as follows Step 1 In the DC Viewer installation window click on lt Next gt to start installation Step 2 The status bar will show the installation progress After the installation is completed click on lt Finish gt to exit the installation process Step 3 Click on lt Finish gt to close the DC Viewer installation page Once the DC Viewer is successfully installed the IP Camera s Home page will be able to correc
37. from 1 frame to 15 frames AN NOTE Make sure FTP configuration has been completed Refer to FTP for further details 93 TM razberi technologies e Upload Image by E Mail Select this item and the Administrator can assign an e mail address and configure various parameters When tampering is detected event images will be sent to the appointed e mail address lt Pre trigger buffer gt function allows users to check what happened to cause the trigger The lt Pre trigger buffer gt frame rate could be pre determined On the other hand lt Post trigger buffer gt is for users to upload certain amount of images after tampering occurs Check the box lt Continue image upload gt to upload the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploading by E mail when tampering is triggered The setting range is from 1 to 9999 seconds Select lt Upload during the trigger active gt to make the images keep being upload to E mail during the trigger active until tampering stops Set the Image frequency as the upload frame rate The setting range is from 1 frame to 20 frames NOTE Make sure SMTP configuration has been completed Refer to Mail for further details e Send HTTP notification Check this item select the destination HTTP address and specify the parameters for HTTP notifications When the Tamperin
38. future use Click on the lt Export gt button and the popup File Download window will come out as shown below Click on lt Save gt and specify a desired location for saving the configuration file Upload To copy an existing configuration file to the IP Camera please first click on lt Browse gt to select the configuration file and then click on the lt Upload gt button for uploading 62 razberi technologies M 7 3 7 3 1 Streaming Under the tab lt Streaming gt there are submenus including lt Video Format gt lt Video Compression gt lt Video OCX Protocol gt lt Video Frame Rate gt lt Video Mask gt and lt Audio gt In the Streaming submenus the Administrator can configure specific video resolution video compression mode video protocol audio transmission mode etc Further details of these settings will be specified in the following sections Video Format Video Resolution and Rotate Type The Video Format setting can be found under this path Streaming gt Video Format Video Format Under Video Resolution section the available video resolution formats are including MJPEG and H 264 Please refer to the User s Manual for more combination details Click on lt Save gt to confirm the setting Text Overlay Settings Users can select the items to display data including date time text on the live video pane The maximum length of the string is 20 alphanumeric characters Click on lt Save gt
39. g ex 192 168 7 254 Click on lt Save gt to confirm the new setting When using static IP address to login to the IP Camera users can access it either through DeviceSearch software refer to User s Manual or input the IP address in the URL bar and click on lt Enter gt gt IP address razberi technologies M This is necessary for network identification gt Subnet mask It is used to determine if the destination is in the same subnet The default value is 255 255 255 0 gt Default gateway This is the gateway used to forward frames to destinations in different subnet Invalid gateway setting will fail the transmission to destinations in different subnet gt Primary DNS Primary DNS is the primary domain name server that translates hostnames into IP addresses gt Secondary DNS Secondary DNS is a secondary domain name server that backups the primary DNS Use PPPoE For the PPPoE users enter the PPPoE Username and Password into the fields and click on the lt Save gt button to complete the setting Advanced Web Server port The default web server port is 80 Once the port is changed the user must be notified the change for the connection to be successful For instance when the Administrator changes the HTTP port of the IP Camera whose IP address is 192 168 0 100 from 80 to 8080 the user must type in the web browser htip 1192 168 0 100 8080 instead of http 192 168 0 100 RTSP por
40. g Alarm is triggered the HTTP notifications can be sent to the specified HTTP server For instance if the custom parameter is set as action 1 amp group 2 and the HTTP server name is http 192 168 0 1 admin php the notification will be sent to HTTP server as http 192 168 0 1 admin php action 1 amp group 2 when alarm is triggered File Name The uploaded images filename format can be set in this section Please select the one that meets your requirements razberi technologies M 7 2 11 Save Click on the lt Save gt button to save all the Tampering Alarm settings mentioned above Storage Management Local Recording The Storage Management setting can be found under this path System gt Storage Management Users can implement local recording to the Micro SD SDHC card up to 32GB This page shows the capacity information of the Micro SD card and a recording list with all the recording files saved on the memory card Users can also format the SD card and implement automatic recording cleanup through the setting page To implement Micro SD card recording please go to the lt Recording gt page refer to Recording for activation NOTE Please format the Micro SD SDHC card when using for the first time Formatting will also be required when a memory card already being used on one camera and later transferred to another camera with different software platform Device information When users insert the Micro SD
41. g a Sequence Line in full screen mode please move the cursor onto the live view pane right click and left click to select fullscreen Then users can view the camera navigation in full screen To stop running the Sequence Line simply move the cursor to the live view pane and move the camera in any direction Pan Tilt Control The Pan Tilt Control Setting can be found under this path Pan Tilt gt Pan Tilt Control Users can activate the pan tilt function and select the RS 485 protocol which the Pan Tilt Head uses in the Pan Tilt Control page Pan Tilt Control Users can enable or disable the Pan Tilt Control Click on lt Save gt to confirm the setting RS 485 Protocol Type Protocol and Baud rate type options include e DSCP 9600 e PelcoD 2400 e PelcoD 4800 e PelcoD 9600 e PelcoP 2400 e PelcoP 4800 e PelcoP 9600 Click on lt Save gt to confirm the setting Move the camera to the desired position by moving the mouse cursor onto the screen one left click on mouse and then dragging the red arrovv to pan tilt TI razberi technologies 7 6 Logout Click on the tab lt Logout gt on the top of the page and the login window will pop up This enables log in with another user name 78 razberi technologies M Appendix A Technical Specifications Camera Image Sensor Effective Pixels Minimum Illumination Color Shutter Speed White Balance rT D 0 Fixed Lens 7 OV
42. ly BNC SUPPORT 1920 x 1080 15fps E S ronson gt omme gt we 352 x 240 30fps H 264 Only BNC SUPPORT 1920 x 1080 15fps E gt or ere a o o OOO TOKOM sto toon oe o Default Click on lt Save gt to confirm the setting 17 TM razberi technologies 2M Real time Model Video Format Under Video Resolution section select a preferred resolution setting The available Video Resolution for MJPEG amp H 264 format includes H 264 H 264 H 264 2 BNC SUPPORT 720 x 480 30fps rr TT ET moroa TT zere TT wwo aoso TT mowe o anes RENE wwo SSS wowo NN RENE mom TT mows RENEE reos RENE smeo TT 1280 x 720 30fps za aso gj RENE wowo RENEE emo o 1024 1768 ej TT wwo RENEE wowo RENE Po gj TT en ce r mwmw 800 x 600 30fps ormo RENE wwo gt 1920 x 1080 30fps razberi technologies M 720 x 480 30fps 640 x 480 30fps m 640 x 480 30fps 352 x 240 30fps 352 x 240 30fps m H 264 MJPEG BNC SUPPORT 720 x 480 30fps om gt ws o cn o e TT wwo A aoas o morro gt Ic SSS aso gj TT rs ao aj TT om SSS zo oe TT aros RENE Ur TT 1280 x 720 30fps Po gj TT so ao oj TT mom SS aeos wwo o C wwo TT 19 TM razberi technologies 800 x 600 30fps 720 x 480 30fps 640 480 303 640 x 480 30fps 352 x 240 30fps 352 x 240 30fps NI MJPEG Only BNC SUPPORT 1920 x 1080 30fps
43. m output to enable alarm relay output when motion is detected 47 razberi technologies 48 Record stream to SD Card Select this item and the Motion Detection recording will be stored in Micro SD SDHC card when motion is detected Pre trigger buffer recording function allows users to check what happened to cause the trigger The pre trigger buffer time range is from 1 to 3 seconds Select SUpload for secz to set the recording duration after motion event occurs The setting range is from 1 to 99999 seconds Select lt Upload during the trigger active to record the triggered video until the trigger is off NOTE Please make sure the local recording with Micro SD SDHC card is activated so that this function can be implemented Refer to Recording for further details Send Alarm Message by FTP E Mail The Administrator can select whether to send warning messages by FTP and or E Mail when motion is detected Upload Image by FTP Select this item and the Administrator can assign a FTP site and configure various parameters When motion is detected event images will be uploaded to the appointed FTP site lt Pre trigger buffer gt function allows users to check what happened to cause the trigger The lt Pre trigger buffer frame rate could be pre determined On the other hand Post trigger buffer gt is for users to upload certain amount of images after motion event occurs Check the box Continue image upload to upload
44. n the user name list There is a maximum of twenty user accounts Each user can be assigned the privileges of Camera control Talk and Listen e I O access This item supports fundamental functions that enable users to view video when accessing to the camera e Camera control This item allows the appointed User to change camera parameters on the Camera Setting page e Talk Listen Talk and Listen functions allow the appointed user in the local site PC site communicating with for instance the administrator in the remote site 29 TM razberi technologies 1 2 2 2 30 Manage User e Delete user To delete a user pull down the user list and select the user name you wish to delete Then click on lt Delete gt to remove it e Edit user Pull down the user list and select a user name Click on lt Edit gt to edit the user s password and privilege NOTE It is required to enter the User password as well as check the function items which will be available for the user When finished click on lt Save gt to modify the account authority HTTPS The HTTPS setting can be found under this path System gt Security gt HTTPS lt HTTPS gt allows secure connections between the IP Camera and web browser using lt Secure Socket Layer SSL gt or lt Transport Layer Security TLS gt which ensure camera settings or Username Password info from snooping It is required to install a self signed certificate or a C
45. ode if this triggered action is enabled e Send Alarm Message by FTP E Mail 41 razberi technologies M 42 The Administrator can select whether to send an alarm message by FTP and or E Mail when an alarm is triggered Upload Image by FTP Select this item and the Administrator can assign a FTP site and configure various parameters When the alarm is triggered event images Will be uploaded to the appointed FTP site lt Pre trigger buffer gt function allows users to check what happened to cause the trigger The lt Pre trigger buffer gt frame rate could be pre determined On the other hand Post trigger buffer gt is for users to upload certain amount of images after the alarm input is triggered Check the box Continue image upload to upload the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploaded to FTP when the alarm input is triggered The setting range is from 1 to 9999 seconds Select lt Upload during the trigger active gt to make the images keep being uploaded to FTP during the trigger active until the alarm is released Set the Image frequency as the upload frame rate The setting range is from 1 frame to 15 frames AN NOTE Make sure FTP configuration has been completed Refer to FTP for further details Record Stream to SD Card Select the item and the alarm triggered recording
46. ols and plug ins 10 Script ActiveX controls marked safe for scripting Click on lt OK gt to accept the settings and close the Security Settings window Click on lt OK gt to close the Internet Options screen Close the browser window and restart a new one later to access the IP Camera razberi technologies Appendix E Install UPnP Components Please follow the instructions below to install UPnP components on Windows Vista Windows XP Windows 7 Step1 In the Windows go to Start Menu click on Control Panel gt and then double click on lt Add or Remove Programs gt Step 2 Click on lt Add Remove Windows Components gt in the Add or Remove Programs page Step 3 Select lt Networking Services gt from the Components list in the Windows Components Wizard window and then click on lt Details gt Step 4 Select SUPnP User Interface in the Networking Services subcomponents list and then click on lt OK gt Step 5 Click on lt Next gt in the Windows Components Wizard window Step 6 Click on lt Finish gt to complete installation 83 TM razberi technologies 84 Razberi Technologies 1628 Valwood Pkwy 148 Carrollton TX 75006 P 469 828 3380 vvvvvv razberi net razberi technologies
47. om The camera s digital zoom is adjustable from x2 to x8 Click on lt V gt to confirm the new setting IR Function Compact Fixed Dome Excluded The IR Function Setting can be found under this path Camera gt IR Function Auto On Off Mode With the IR cut filter the Camera can still catch clear image at night time or in low light conditions For the camera with the built in IR LED module there will be three additional IR function modes Light Sensor Light On Light Off as follows Light Sensor Mode IR LED lights will be turned on off depending on the light sensor Light On Mode In this mode IR LED lights will be always on Light Off Mode In this mode IR LED lights will be always off Smart Mode The Smart Mode enhances the monochrome night mode stability in the scenario that IR illumination is dominant In this mode when the external IR illuminator is turned on the IR cut filter of the IP Camera will keep open i e monochrome night mode preventing the camera from returning to the color day mode when IR illumination is dominant Additionally for the models with built in IR LED module the day night IR switching mechanism will depends on the ambient light level instead of the light sensor Light sensor mode on the IR LED module Click on lt gt to confirm the new setting razberi technologies 1 4 7 7 4 8 7 4 9 WDR Function The WDR Function Setting can be found under this path Camera gt
48. ound C IP Relay aa a Device Search SP Ie 192 168 0 101 80 23 255 8500 MegePixelCamers B0 89 03 D8 B1 LF200 LP200 MegePixelCamera 192 168 0 105 80 2 Enter the default username and password The default Administrator login ID and password Login ID Password AN NOTE Login ID and password are case sensitive NOTE It is strongly advised that the administrator s password be altered for security concerns Refer to System Menu for razberi technologies further details Additionally users can change the IP Camera s network property either DHCP or Static IP directly in the device finding list Refer to the following section for changing the IP Camera s network property Example of Changing the IP Camera Network Property to DHCP Step 1 In the finding device list click on the desired IP Camera to change its network property Record the IP Camera s MAC address for future identification On the selected item right click and select Network Setup io xi Search Method E ar 2 device s found C IP Relay afro z Device Search ra i i 80 E 8500 MegaPixelCamera 192 169 0 101 pep 99 09 08 B81 Detail Info S Browse Network Setup LP200 LP200 MegaPixelCamera 192 168 0 105 80 B9 08 40 B7 Step 2 The Network Setup page will pop up Select DHCP and press Apply button down the page Step 3 Click on lt OK gt on the Note of setting change Wait
49. rocedure of software upgrade Is as below Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Click on Browse and select the binary file to be uploaded ex ulmage userland NOTE Do not change the upgrade file name or the system will fail to find the file Pull down the upgrade binary file list and select the file ulmagetuserland img Click on the lt Upgrade gt button The system will check whether the upgrade file exists or not first and then begin to upload the upgrade file Subsequently the upgrade status bar will display on the page When it runs to 100 the upgrade process is finished After the upgrade process is finished the vievver vvill return to Home page Close the video brovvser Start SControl Panel gt on your PC and then double click on SAdd or Remove Programs In the lt Currently install programs gt list select lt DCViewer gt and click on the button Remove to uninstall the existing DC Vievver Open a new web browser re login the IP Camera and then allow the automatic download of DC Vievver 61 TM razberi technologies 7 2 21 Maintenance The Maintenance setting can be found under this path System Maintenance Users can export configuration files to a specified location and retrieve data by uploading an existing configuration file to the IP Camera Export Users can save the system settings by exporting the configuration file bin to a specified location for
50. rom 1 to 99999 seconds Select SUpload during the trigger active to record the triggered video until the trigger is off NOTE Please make sure the local recording with Micro SD SDHC card is activated so that this function can be implemented Refer to Recording for further details Send Alarm Message by FTPJE Mail The Administrator can select vvhether to send an alarm message by FTP and or E Mail when tampering is detected Upload Image by FTP Select this item and the Administrator can assign a FTP site and configure various parameters When tampering is detected event images Will be uploaded to the appointed FTP site sPre trigger buffer function allows users to check what happened to cause the trigger The lt Pre trigger buffer frame rate could be pre determined On the other hand lt Post trigger buffer gt is for users to upload certain amount of images after tampering is triggered Check the box lt Continue image upload gt to upload the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploaded to FTP when tampering is triggered The setting range is from 1 to 9999 seconds Select lt Upload during the trigger active gt to make the images keep being upload to FTP during the trigger active until the tampering stops Set the Image frequency as the upload frame rate The setting range is
51. snapshots and web recording will be saved in the designate location NOTE Please make sure the selected file path contains valid characters such as letters and numbers NOTE For users with Windows 7 operating system it is reguired to log on as an Administrator to implement the Snapshot and Web Recording function Iris Adjustment Fixed Focal Lens Excluded The Iris Adjustment function can be found under this path System gt Iris Adjustment For users who use Auto iris lens when it is required to implement iris adjustment please refer to the Iris adjustment procedure in the setting page to adjust Iris View Log File The View Log File function can be found under this path System gt View Log File Click on the tab to view the system log file The content of the file provides useful information about connections after system boot up razberi technologies M 7 2 16 7 2 17 View User Information The View User Information function can be found under this path System gt View User Information The Administrator can view each added user s login information and privileges refer to Security View User Login Information All the users in the network will be listed in the lt User information gt zone as shown below User 4321 It indicates that one user s login username is User and the password is 4321 View User Privilege Click on lt get user privacy at the bottom of the page and the Administrator can
52. t The default setting of RTSP Port is 554 the setting range is from 1024 to 65535 MJPEG over HTTP port The default setting of MJPEG over HTTP Port is 8008 the setting range is from 1024 to 65535 35 TM razberi technologies 1 2 3 2 36 e HTTPS port The default setting of HTTPS Port is 443 the setting range is from 1024 to 65535 AN NOTE Be avvare to choose the different port from the one set for the web server port IPv6 Address Configuration With IPv6 support users can use the corresponding IPv6 address for browsing Enable IPv6 by checking the box and click on lt Save gt to complete the setting QoS The QoS Quality of Service setting can be found under this path System gt Network gt QoS QoS allows providing differentiated service levels for different types of traffic packets which guarantees delivery of priority services especially when network congestion occurs Adapting the Differentiated Services DiffServ model traffic flows are classified and marked with DSCP DiffServ Codepoint values and thus receive the corresponding forwarding treatment from DiffServ capable routers DSCP Settings The DSCP value range is from 0 to 63 The default DSCP value is 0 which means DSCP is disabled The IP Camera uses the following QoS Classes Video Audio and Management e Video DSCP The class consists of applications such as MJPEG over HTTP RTP RTSP and RTSP HTTP e Audio DSCP This setting is only a
53. the box to enable IEEE 802 1X Click on lt Save gt to save the IEEE 802 1X EAP TLS setting 33 TM razberi technologies 7 2 3 7 2 3 1 34 Network The Network setting can be found under this path System gt Network Click on the lt Network gt category there will be a drop down menu with tabs including lt Basic gt lt QoS gt lt SNMP gt and lt UPnP gt Basic The Basic setting can be found under this path System gt Network gt Basic Users can choose to connect to the IP Camera with fixed or dynamic DHCP IP address The IP Camera also provides PPPoE support for users who connect to the network via PPP over Ethernet PPPoE General e Get IP address automatically DHCP The camera s default setting is lt Use fixed IP address gt Please refer to User s Manual for login with the default IP address If select lt Get IP address automatically gt after the IP Camera restarts users can search it through the installer program DeviceSearch exe which can be found in DeviceSearch folder in the supplied CD NOTE Please make the record of the IP Camera s MAC address which can be found in the label of the camera for identification in the future e Use fixed IP address To setup static IP address select lt Use fixed IP address gt and move the cursor to the IP address blank and insert the new IP address ex 192 168 7 123 then go to the Default gateway explained later blank and change the settin
54. the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploaded to FTP when the motion event occurs The setting range is from 1 to 9999 seconds Select lt Upload during the trigger active to make the images keep being uploaded to FTP during razberi technologies M the trigger active until the event stops Set the Image freguency as the upload frame rate The setting range is from 1 frame to 15 frames AN NOTE Make sure FTP configuration has been completed Refer to FTP for further details Upload Image by E Mail Select this item and the Administrator can assign an e mail address and configure various parameters VVhen motion is detected event images will be sent to the appointed e mail address sPre trigger buffer function allows users to check what happened to cause the trigger The lt Pre trigger buffer frame rate could be pre determined On the other hand lt Post trigger buffer gt is for users to upload certain amount of images after the motion event occurs Check the box lt Continue image upload gt to upload the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploading by E mail when the motion event occurs The setting range is from 1 to 9999 seconds
55. tly display as the figure below F Main Tabs Streaming Camera Logout Viewer Window Language Selection razberi Langu ges 2010 0522 12 51 Time Display Video Format Selection Video Streaming Pause Button Snapshot Button Speaker Button Talk Button Display Mode Image and Focus Adjustment The image displays on the Home page when successfully accessing to the IP Camera Adjust zoom and focus as necessary to produce a clear image 12 razberi technologies M Note Please refer to Full HD Multiple Streams IP Camera Menu Tree for more button function detail 13 TM razberi technologies 14 Setup Video Resolution Users can setup Video Resolution on the Video Format page of the user friendly browser based configuration interface Video Format can be found under this path Streaming Video Format razberi Video Format Video Compression Video OCX Protocol Video Frame Rate Video Mask System Streaming amera Logout Video Format Video Resolution H 264 H 264 v H 264 1 format 1920 x 1080 30 fps v H 264 2 format 720 x 480 30 fps v BNC support Yes Save Note Image attachment by FTP or E mail will be available only while MJPEG streaming is selected Text Overlay Settings I Include date I Include time U Include text string Save Video Rotate Type Normal video I Save GOV Settings H 264 1 GOV Length 60 H 264 2 GOV Length 60
56. to confirm the Text Overlay setting Video Rotate Type Users can change video display type if necessary Selectable video rotate types include Normal Flip Mirror 90 degree clockwise 180 degree rotate and 90 degree counterclockwise 63 TM razberi technologies 1 3 2 64 The following is descriptions for different video rotate type e Flip If select lt Flip gt the image will be rotated vertically e Mirror If select lt Mirror gt the image will be rotated horizontally e 90 Degree counter clockwise Selecting lt 90 Degree Counter clockwise gt will make the image 90 counter clockwise inversed e 180 Degree Rotate Selecting lt 180 Degree gt will make the image 180 inversed Click on lt Save gt to confirm the setting GOV Settings Users can set the GOV length to determine the frame structure l frames and P frames in a video stream for saving bandwidth The setting range is from 2 to 64 Default value is 60 which means there s one I frame every 60 frames Longer GOV length means lower I frame frequency Click on lt Save gt to confirm the GOV setting Video Compression The Video Compression setting can be found under this path Streaming gt Video Compression Users can select a proper MJPEG H 264 compression mode in the video compression page depending on the application MJPEG Q Quality factor Higher value implies higher bit rates and higher visual quality The default setting of MJPEG Q
57. tter speed according to the environmental illumination 69 TM razberi technologies 7 4 2 70 White Balance Setting The White Balance Setting can be found under this path Camera gt White Balance A camera needs to find reference color temperature which is a way of measuring the quality of a light source for calculating all the other colors The unit for measuring this ratio is in degree Kelvin K Users can select one of the White Balance Control modes according to the operating environment The following table shows the color temperature of some light sources for reference Light Sources Color Temperature in K Cloudy Sky 6 000 to 8 000 Noon Sun and Clear Sky 6 500 Household Lighting 2 500 to 3 000 75 watt Bulb 2 820 Candle Flame 1 200 to 1 500 AWB Auto White Balance The Auto Balance White mode is suitable for environment with light source having color temperature in the range roughly from 2700 7800K ATW Mode Auto Tracking White Balance With Auto Tracking White Balance function the white balance in a scene will be automatically adjusted while temperature color is changing The ATW Mode is suitable for environment with light source having color temperature in the range roughly from 2500 10000K Manual Mode In this mode users can change the White Balance value manually Users can select a number between 0 127 of Rgain Bgain item to gain the red blue illuminant on the Live Video Pane Cli
58. vailable for the IP Cameras that support audio e Management DSCP The class consists of HTTP traffic Web browsing AN NOTE To enable this function please make sure the switches routers in the network support QoS razberi technologies 7 2 3 3 SNMP The SNMP Simple Network Management Protocol setting can be found under this path System gt Network gt SNMP With Simple Network Management Protocol SNMP support the IP Camera can be monitored and managed remotely by the network management system SNMP v1 v2 e Enable SNMP v1 v2 Select the version of SNMP to use by checking the box e Read Community Specify the community name that has read only access to all supported SNMP objects The default value is public e Write Community Specify the community name that has read write access to all supported SNMP objects except read only objects The default value is write Traps for SNMP v1 v2 Traps are used by the IP Camera to send massages to a management system for important events or status changes e Enable Traps Check the box to activate trap reporting e Trap address Enter the IP address of the management server e Trap community Enter the community to use when sending a trap message to the management system Trap Option e Warm Start A Warm Start SNMP trap signifies that the SNMP device i e IP Camera performs software reload 3 TM razberi technologies 7 2 3 4 38 Click on lt Save
59. vents by sending out notifications or uploading snapshots to the specified destination s Detection of camera tampering is achieved by measuring the differences between the older frames of video which are stored in buffers and more recent frames Tampering Alarm Users are able to turn on off Tampering Alarm function in Tampering Alarm setting page The default setting is Off Tampering Duration Minimum Tampering Duration is the time for video analysis to determine whether camera tampering has occurred Minimum Duration could also be interpreted as defining the Tampering threshold longer duration represents higher threshold Settable Tampering Duration time range is from 10 to 3600 seconds The Default value is 20 seconds Triggered Action Multi option The Administrator can specify alarm actions that will take when tampering is detected All options are listed as follows e Enable Alarm Output Check the item and select the predefined type of alarm output to enable alarm output when tampering is detected e Record stream to SD Card Select this item and the Tampering Alarm recording will be stored in Micro SD SDHC card when tampering is detected Pre trigger buffer recording function allows users to check what happened to cause the trigger The pre trigger buffer time range is from 1 to 3 seconds razberi technologies M Select SUpload for secz to set the recording duration after tampering occurs The setting range is f
60. will be directly recorded to the specific location on the local hard drive which could be configured in the lt File Location gt page The default storage location for the web recording is C Please refer to File Location for further details AN NOTE For users vvith VVindovvs 7 operating system it is required to log on as an Administrator to implement the VVeb Recording function Zoom Adjustment e Tele Wide buttons Wide Tele Hold the lt Tele Wide gt button and implement continuous zoom adjustment e Tele Wide Steps buttons _ 2 Siers Wide Sieps Click on the lt Tele Wide Steps gt buttons will lead zoom to be shifted toward Tele Wide sides in user defined range which can be selected from the drop down menu Manual Focus Adjustment e Manual button Manualj Click on the lt Manual gt button and users can adjust focus manually via the NeariFar buttons at the right side of Manual button e Near Far buttons Neat Far Hold the lt Near Far gt button and implement continuous focus adjusiment e Near Far Steps buttons N s Stepe Fa Steps Click on the lt Near Far gt buttons will lead focus to be altered toward Near Far sides in user defined range which can be selected from the drop down menu razberi technologies M Auto Focus AF Adjustment The AF mode can be defined as of automatic zoom triggered and one push Auto Continuous AF Auto In this mode the camera will keep in focus automatically
61. will be saved into your Micro SD card Pre trigger buffer recording function allows users to check what happened to cause the trigger The pre trigger buffer time range is from 1 to 3 seconds Select lt Upload for __ sec gt to set the recording duration after alarm is triggered The setting range is from 1 to 99999 seconds Select lt Upload during the trigger active gt to record the triggered video until the trigger is off razberi technologies NOTE Please make sure the local recording with Micro SD SDHC card is activated so that this function can be implemented Refer to Recording for further details Upload Image by E Mail Select this item and the Administrator can assign an e mail address and configure various parameters When the alarm input is triggered event images Will be sent to the appointed e mail address lt Pre trigger buffer gt function allows users to check what happened to cause the trigger The lt Pre trigger buffer frame rate could be pre determined On the other hand Post trigger buffer gt is for users to upload certain amount of images after alarm input is triggered Check the box Continue image upload to upload the triggered images during certain time or keep uploading until the trigger is off Select lt Upload for _ sec gt and enter the duration in the blank The images of the duration will be uploading by E mail when the alarm input is triggered The setting range is from 1 to 9999 se
62. with indication of motion will be shown Motion x When motion is detected the signals will be displayed on the Motion window as shown below hag on VA ge 14 27 S razberi technologies TM Motion Detection Users are able to turn on off Motion Detection Default setting is Off Motion Detection Setting Users could adjust various parameters of Motion Detection in this section Sampling pixel interval 1 10 The default value is 1 If the value is set as 3 it means within the detection region system will take one sampling pixel for every 3 pixels by each row and each column refer to the figure below Detection level 1 100 The default level is 10 The item is to set detection level for each sampling pixel the smaller the value the more sensitive it is Sensitivity level 1 100 The default level is 80 which means if 20 or more sampling pixels are detected differently system will detect motion The bigger the value the more sensitive it is Meanwhile when the value is bigger the red horizontal line in the motion indication window will be lower accordingly Time interval sec 0 7200 The default interval is 10 The value is the interval between each detected motion Triggered Action Multi option The Administrator can specify alarm actions that will take when motion is detected All options are listed as follows Enable Alarm Output Check the item and select the predefined type of alar

User`s Manual - Razberi Technologies

Contents

Download Pdf Manuals

Related Search

Related Contents