Edge 85 MXP - Extron Electronics
Contents
1. Input Near Main Camera Doc Camera Aux VCR IR Remote Emulation 0 9 i Connect Disconnect Up Down Right Left Selfview Layout Phonebook Cancel Mic Off Presentation Volume Up Volume Down OK Zoom In Zoom Out a Menu Navigation Up Left Right Cancel Directory Microphone Mute On Off Pan Tilt Far Down Right Pan Tilt Near Phone Call Call End Call Picture In Picture On Off Auto Power Control On Off Page 4o0f5 IP Link Device Interface Communication Sheet Selfvie w Off On Presentation Source Current Video 1 Video 2 Video 3 Video 4 Video 5 tand_12_3423_4 pke Revision 2 28 2011 1 Will control camera with camera Id 1 2 This command serves the same function as the OK Menu button on the remote Cableand Adapter Requirements M F RS 232 Straight Serial Cable Extron Electronics P N 26 433 XX Notes for the Device Device can support upto 13 cameras if Tandberg video switchers are used Serial communication Port Type RS 232 Parity None Baud Rate 9600 StopBits 1 Data Bits 8 Flow Control None Pin Assignments Diagram COM 5 1 5 HH cme 9 6 6 9 RxD 2 TxD RS232 DB9 Male SA TxD 3 _ _ _ _ _ 3 RxD A IE RS232 DB9 Female IP Link Device GND 5 A 5 GND Video Conference Interface J Note Captive screw connector may also be used as a serial connection General Notes Page 50f52. mote Asterik is also used as a period Page 1 of5 tand_12_3423_4 pke IP Link Device Interface Revision 2 28 2011 Communication Sheet Control Commands amp States a a Focus Near Input ap Input Near Main Camera Doc Camera Aux VCR IR Remote Enulation 0 9 si Connect Disconnect Up Down Right Left Selfview Layout Phonebook Cancel Mic Off Presentation Volume Up Volume Down OK Zoom In Zoom Out a Menu Navigation Up Left Right Cancel Directory Pan Tilt Far Down Right Pan Tilt Near Phone Call Call End Call Page 20f5 tand_12_3423_4 pke IP Link Device Interface Revision 2 28 2011 Communication Sheet Picture In Picture On Off Auto Power Control On Off Presentation Source Current Video 1 Video 2 Video 3 Video 4 Video 5 1 Will control camera with the selected camera Id 2 This command serves the same function as the OK Menu button on the remote Status Available Auto Answer On Off Mute Connection Status Connected Disconnected Display Mode Single Dual Input Near Main Camera Doc Camera PC VCR Microphone Mute Off On Screen Display Off Picture In Picture On Off Auto Power Control On Off Presentation Source Current Video 1 Video 2 Video 3 Video 4 Video 5 Volume Discrete Oto 21 in steps of Page 30f5 tand_12_3423_4 pke IP Link Device Interface Revision 2 28 2011 Communication Sheet MLC62 Supported Commands i a Focus Near
3. tand_12_3423_4 pke IP Link Device Interface Revision 2 28 2011 Communication Sheet This document provides additional assistance with wiring your Extron IP Link enabled product to your device Different components may require a different wiring scheme than those listed below For complete operating instructions refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation Device Specifications Device Type Video Conference Manufacturer Tandberg Firmware Version F6 1 Model s Edge 85 MXP Edge 95 MXP Edge 75 MXP Version History Driver IP Link GC Version Date Compiler Version Notes 4 2 21 2011 1 4 0 3 0 4 Extron Certified Added IR Remote Fmulation command 3 01 13 2010 1 40 302 Extron Certified Tested on Edge 95 MXP Added Auto Focus Power Control and Camera Id for auxiliary camera control Extron Certified Tested on Edge 95 MXP Updated several 2 COA ZOO Bard eon commands Added far end input and camera control 1 03 23 2009 1 3 11 1 2 5 00 Extron Certified Tested on Edge 95 MXP Driver Notes Camera Control Commands are all Press Release buttons where controls are activated when the button is pressed and stops once the button is released The Stop command is for configuration purposes Driver is not recommended with pass through mode IR Remote Emulation Dial Keypad and Menu Navigation simulatethe IR codes of the re
Download Pdf Manuals
Related Search