EEAC321A - Snap
Contents
1. Open the Red Valve on the Recovery Tank 7 Raise the Virgin Tank to a higher level than the Recovery Tank Invert the Virgin Tank A and open valve 8 Gravity and vacuum will transfer the liquid refrigerant to the Recovery Tank faster than recovering it NOTE DO NOT OVER CHARGE TANK THE C Z SAFE AMOUNT TO CHARGE IS AROUND 15 LBS z 9 After the desired amount of refrigerant has been fa transferred close valves on Virgin Tank first pause to allow refrigerant to flow into tank then close Ar recovery tank valve Set Virgin Tank on ground i a upright 10 Disconnect blue hose and adapter from both Tanks 11 Re Oil seals on anti blow back valve on the Red Hose from unit and connect to Recovery Tank Open both Recovery Tank valves FIGURE 2 CHARGING TANK 12 Re Oil seals on red and blue hoses To connect the hoses route both in between the master filter bracket and the hose that connects to the filter Connect the open end of the Blue hose to the Low side bulkhead fitting and Red Hose to the high side bulkhead fitting Using the plastic tie wrap route the tie through the hole in the bracket wrap around the hoses and tie 13 Unit is ready to recover and charge refrigerant REMEMBER TO OIL O RINGS AND SEALS WHEN ATTACHING HOSES OR FITTINGS TEEAC321A0 08 16 2002 REV A2. ALLATION ALWAYS WEAR SAFETY GOGGLES DON T SPILL OR TOUCH LIQUID REFRIGERANT AVOID FLAMES AND EXCESSIVE HEAT USE ONLY IN WELL VENTILATED AREA PARTS amp ACCESSORIES SETUP 1 Remove the Blue and Red Hoses from the box along with the plastic tie wrap Remember to OIL the seals on each end of the hoses Connect the high red and low blue couplers to their respective hoses Rotate coupler knobs fully CCW closed Route both hoses in between the master filter bracket and the hose that connects to the filter Attach other end of the red hose to upper red labeled high side port on the back panel of the Eco Xtreme unit Attach other end of the blue hose to lower blue labeled low side port on the back panel of the Eco Xtreme unit The plastic tie wrap will be used later to secure the hoses to the master filter bracket Page 4 line 12 Install plastic oil bottle 1 05585A to the white cap mounted in the front of the unit Remove the User s Manual from the box Hand this item to the Owner or Manager Remove Recovery Tank EAA0275L05A from its box Remove cardboard wrap from Recovery Tank and set on floor TEEAC321A0 08 16 2002 REV A Page 3 of 4 PREPARING RECOVERY TANK 1 Referring to FIGURE 1 open the BLUE valve on Recovery Tank to release ALL COMPRESSED AIR Gently set the Recovery Tank on the scale Place the strap around the recovery tank Position the Temperature Probe between th
3. EEAC321A ECO Xtreme International UNIT SETUP 1 of 4 Installation Instructions INSTALLATION MUST BE PERFORMED BY QUALIFIED PERSONNEL ONLY INSTALLATION OVERVIEW The Installation Procedure listed is for the Snap on ECO Xtreme International EEAC321A The unit is shipped as a fully assembled unit with the exception for the items listed in the Parts amp Accessories PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE SETTING UP UNIT PARTS amp ACCESSORIES PART NUMBER DESCRIPTION QTY 1 15080 Adapter Low Side 1 1 27180 Adapter Vehicle High Side 1 1 27280 Adapter Vehicle Low Side 1 1 05585A Bottle Disposable 80z 1 5 1145 Plastic tie wrap 1 EAA0275L05A Recovery Tank Assembly R 134a 1 EAH0001C01A Red Hose 1 EAHO040L22A Blue Hose w Vacuum Pump Port 1 EAK0027CO0AS Kit Vehicle Adapter O Ring 1 TEEAC321A0 Installation Instructions 1 1 ZEEAC318A06 User s Manual REQUIRED TOOLS e Safety Goggles e R 134a Virgin Tank Supplied by Customer e Gloves TEEAC321A0 08 16 2002 REV A Page 2 of 4 A CAUTION THIS UNIT MUST BE PLUGGED INTO A PROPER AC OUTLET FOR UNIT TO OPERATE CORRECTLY REFER TO THE UNIT ID PLATE LOCATED ON BACK OF UNIT EXTENSION CORDS ARE NOT RECOMMENDED BUT IF AN EXTENSION CORD MUST BE USED USE A CORD THAT IS LESS THAN 50 FEET WITH A 16 AWG OR ABOVE 50 FEET AND LESS THAN 100 FEET WITH A 14 AWG A WARNING USE STANDARD REFRIGERANT HANDLING SAFETY PROCEDURES WHEN PERFORMING INST
4. ck valve to the blue liquid valve Pamas If you are going to continue with Gravity refrigerant transfer ie Port found on page 4 leave the red hose disconnected a AN Otherwise identify the red hose leading from the bottom of the unit Connect hose with the anti blowback valve to the red vapor valve Open both red and blue valves on tank unless continuing with Gravity Transfer method If you are going to continue with Gravity refrigerant transfer do not attach plastic tie Using the plastic tie wrap 5 1145 route the tie through the hole in the bracket wrap around the hoses and tie Refer to the users manual for pre charging tanks Refer to next page for first time fast charge INSTALLATION COMPLETE TEEAC321A0 08 16 2002 REV A Page 4 of 4 PRE CHARGING RECOVERY TANKS USING GRAVITY METHOD NOTE THIS PROCEDURE IS USED TO SETUP THE UNIT FOR CHARGING RECOVERY TANK SHOULD HAVE AT LEAST A 25 VACUUM THIS PROCEDURE IS DONE WHEN RECOVERY TANK IS ON THE SCALE 1 Plug unit in and turn on go into Charge screen to monitor tank weight 2 Be sure Recovery Tank valves B are closed and tank is in vacuum on scale Refer to FIGURE 2 3 Disconnect the Red hose from the Recovery Tank 4 Disconnect and Re Oil both the seals on blue hose C Connect the one side of the blue Hose w adapter 1 15080 to the Virgin Tank A 5 Connect the other end of the blue Hose to the Red Valve on the Recovery Tank B 6
5. e tank and the strap Install the supplied tank adapter 1 15080 on the Low blue side of the recovery tank Attach the blue vehicle hose w adapter to the Low side of the tank Plug AC Cord to a proper AC outlet And turn on the unit by the rear panel switch FIGURE 1 RECOVERY TANK NOTE In the unlikely event the LCD screen is unreadable upon power up adjust LCD contrast Refer to the users manual for contrast adjustment 8 9 10 11 12 13 Press the Down arrow Arrow on display will be pointing to VACUUM a Press lt ENTER gt b Press the Down arrow until desired amount of vacuum time is displayed c Turn the front panel low panel valve to VACUUM d Press Start button vacuum pump should turn ON in about 5 seconds The low side gauge shows vacuum increasing Monitor low side gauge until a minimum of 25 inches has been reached Once completed close the Recovery Tank valve BLUE Close the R 134a Coupler Press EXIT button The pump will shut off Remove the blue service hose from the tank NOTE Remove the R 134a tank adapter 1 15080 and place in the storage tray 14 15 17 18 Identify the three hoses leading from the bottom of the unit Connect the yellow hose to the tank purge port See figure to the right Rotate the tank so the valves face towards the rear of the unit Identify the blue hose leading from the bottom of the unit ay Purge Connect hose with the anti blowba
Download Pdf Manuals
Related Search