BT Accord 30 manual pdm - Connected Essentials Ltd
Contents
1. 3 4 5 Power on off switch 6 Microphone sensitivity control 7 Mute button 8 Telephone or computer selection switch 9 Computer headset socket 3 5mm stereo for speaker plug connection 10 Computer headset socket 3 5mm stereo for microphone plug connection 11 Headset or handset selection switch 12 Modular socket RJ11 for telephone headset connection 13 Sliding volume control 14 Modular socket RJ11 for telephone handset 15 Modular socket RJ11 for connection from the telephone base unit 16 Battery compartment door 2 x AA size batteries required not supplied Ne UO 12 10 13 11 BT Accord 30 manual pdm 15 6 04 5 38 pm Page 4 p Connections Connecting to the computer You may use the BT Accord 20 headset supplied or a computer headset if you Connecting to the telephone Unplug the handset cord from your telephone and plug it into the handset already have one Computer headsets are typically stereo both ears and may be more suitable for some applications games etc modular socket 14 Connect the BT Accord 30 to your telephone using the phone cord provided this cord has an RJ 11 modular plug on either end Plug To connect the BT Accord 30 to your computer you will need to use the long one end OF ine Cord to your telephone fom where yourunplugged your handset A cable supplied with two jack plugs at each end Connect the plugs from one end and the o2. jack of the computer Make sure that the line in cable from the amplifier is connected to the line out jack of the computer and NOT the speaker jack p Information For your safety we advise that you keep this headset and its components away from any liquids Do not attempt to effect repairs yourself seek qualified advice Only use an approved mains adaptor as damage may occur if an incorrect adaptor is used Always operate at a safe volume level to protect your hearing Take a break after using the headset for any length of time Specifications Standard operating voltage 3V DC Operating Current Max 9 mA Standby Current 200 HA Standby Mode Activation 2 3 min without signal Amplifier Gain Speaker 13 dB Max Microphone 30 dB Max Battery 2 x AA Adapter DC input 6V 9V DC Adapter not included Standards Approval CE WFC CEO A copy of the Declaration of Conformity for this product can be found at www easidirect co uk 11 BT Accord 30 manual pdm 15 4 5 38 pm Page 12 1st edition June 2004 12
3. BT Accord 30 manual pdm 15 4 5 38 pm Page 1 oT Installation Guide and User Manual For BT Accord 30 Telephone Amplifier amp Headset Telephone and multimedia headset and amplifier kit with noise cancelling microphone for BT Converse most other corded telephones and multimedia PCs Ideal for use in call centres and offices Includes BT Accord 30 telephone amplifier BT Accord 20 telephone headset Phone cord to connect your BT Accord 30 to your telephone PC connection cable to connect your BT Accord 30 to your computer Screwdriver pin to adjust your microphone sensitivity Replacement parts and accessories are available from your usual supplier or www easidirect co uk BT Accord 30 manual pdm 15 6 04 5 38 pm Page 2 p Before you start The BT Accord 30 is simple to set up and operate but please take the time to read this instruction manual to ensure you get the best from your equipment Your BT Accord 30 amplifier can be connected to your telephone and or your computer You can use it with either the BT Accord 20 headset supplied or with a IO 2 PC headset not included cu T CB 2 0 Op Diagram key Cnn Oa A 1 External DC supply socket 6V DC to 9V DC an optional mains adaptor is Q available a Telephone configuration switch Line in socket 8 5mm stereo for computer line out connection Line out socket 3 5mm stereo for computer line in connection 2
4. Troubleshooting Problem Items to check There is no response from the unit cannot hear any dial tone or my caller speaking to me My caller cannot hear me at all or cannot hear me very well hear my voice too loud and there is a squealing sound When using with my computer the sound is too loud even though the volume is set at minimum 10 Check if battery power is low and replace all batteries if required Check if the batteries are inserted correctly Make sure the on off is switched to on Check if the configuration switch is properly selected Check that the volume control and mute button are adjusted properly Check that the headset handset and the cable connecting the BT Accord 30 to the telephone are properly connected Check if the telephone computer switch 8 is set to telephone Re check your configuration settings pages 4 5 Try other positions until you can hear a dial tone Make sure the mute button is not pressed down Use the screwdriver to see if the microphone sensitivity 6 is set too low Try to select the proper settings with the configuration switch Use the screwdriver to see if the microphone sensitivity 6 is set too high Take a look at the connection on your computer where the cables connect with the BT Accord 30 amplifier There should be 3 jacks line in line out and speaker Make sure the line out cable from the amplifier is connected to the line in
5. ected T BT Accord 30 manual pdm 15 6 04 5 38 pm Page 6 The power on off switch 5 The BT Accord 30 will switch to standby mode automatically after a period of inactivity Turning off the unit does not affect normal telephone communication through the handset so you can answer or make phone calls through the handset as usual Configuring the control unit The telephone configuration switch 2 at the back of the BT Accord 30 allows you to select the most suitable setting for you to work with your telephone To check your configuration put the headset on and move the handset headset switch 11 to the headset position Please make sure you turn down the volume to protect your hearing Make sure the telephone computer switch 8 is set to telephone position Raise the telephone handset and move the 6 position configuration switch slowly until you can hear a clear dial tone Note that there may be two matching settings choose the clearer setting or either one if both perform the same The controls Telephone computer selection switch The telephone computer application switch 8 is for you to select either telephone use or computer use Headset handset selection switch The headset handset application switch 11 is for you to choose between using the handset of your telephone or the BT Accord 20 headset provided Mute switch The mute switch 7 lets you p
6. lace a caller on hold by pressing down to the mute position The caller will not be able to hear you but you will still be able to hear the caller To resume the call press the button again Volume control The sliding volume control 13 is for adjusting the volume of the sound to the headset speaker By sliding the button up and down you can obtain the desired volume BT Accord 30 manual pdm 15 6 04 5 38 pm Page 8 p Microphone sensitivity control The BT Accord 30 allows you to adjust the outgoing sound volume and the high and low frequencies associated with it To fine tune the transmission volume place a call and talk as usual using the headset Slowly rotate the microphone sensitivity control 6 with the small screwdriver pin provided until the desired level is reached The person talking to you should be able to tell you when the optimum sound and tone level is reached Once this is set there should be no need to make further adjustments in the future Caution Be careful when you adjust the volume control as rotating the volume to maximum setting may cause the headset to squeal Reduce the volume and the squealing will disappear but continuous over turning of the control may cause damage to the unit MIC VOL Operation Making calls using the headset Switch to telephone position through the telephone computer selection switch 8 e Make sure the headset position is selected on the headset handset se
7. lection switch 11 Lift up the handset from its cradle and place it off hook you should now hear a dial tone and may dial the number you require e After finishing a call return the handset to its cradle as usual Receiving calls using the headset Switch to telephone position through the telephone computer selection switch 8 e Make sure the headset position is selected on the headset handset selection switch 11 Lift up the handset from its cradle and place it off hook you should now hear your caller and may speak e After finishing a call return the handset to its cradle as usual Using the headset with a computer Switch to computer position through the telephone computer selection switch 8 Select the headset position from the headset handset selection switch 11 e When a telephone call comes in or you want to make a call while working on your computer simply switch to telephone position 8 and lift the handset When you have finished your call simply place the handset back on its cradle and switch back to computer 8 to return to your existing computer work BT Accord Helpline If after following these instructions and carefully checking the settings you require assistance with your BT Accord headset please call 0871 200 2276 between 9 00am and 5 30pm Monday to Friday except public holidays Calls are charged at national rate BT Accord 30 manual pdm 15 6 04 5 38 pm Page 10 p
8. ther end to the telephone base unit modular socket 15 on the back of the cable to the sockets 3 4 on the diagram on page 3 matching the green Ofthe BT Accord 30 66 lustratio below and blue colours on socket and plug Make the same connections to your computer s sound card 14 15 For computer only use you will not need to connect numbers 12 14 and 15 on the diagram on page 3 Congratulations you are now connected Inserting batteries The BT Accord 30 requires 2 x AA sized batteries not supplied To insert batteries slightly depress the compartment lid and slide outwards Install batteries with polarities according to the battery diagram inside the compartment Close the lid and turn the power on 5 Alkaline batteries are recommended If you find Connecting the telephone headset that the volume is too low and you cannot adjust it then this is typically an Insert the telephone headset plug into the RJ 11 modular socket 12 on the indication that the batteries need to be replaced front panel of the BT Accord 30 The headset socket will allow monaural single ear use O e For telephone only use you will not need to connect numbers 3 4 9 and 10 on the diagram on page 3 Congratulations you are now conn
Download Pdf Manuals
Related Search