OLC 7030 - Philips Lighting
Contents
1. Warning The DALI interface is not using safety isolation DA is internally connected to the Neutral conductor Disconnect the main power supply before servicing Wiring Diagram 2 5 Filter 4 DALI is not using I safety isolation Li Ni No Lo Ls Le DA DAHDA DA y F Max 4 4 6A DALI driver L N DALI driver 2 Li Line input Ni Neutral input No Neutral output Ls Switched Line output Lc Controlled Line input Photo cell 0 25 2 5 mm e ns R e 10 11 mm Filter 4 DALI is not using IN A safety isolation Li Ni No Lo Ls Le DA DAHDA DA y 4 Max L Advert 6A light _DALU driver L N DALI driver 2 Li Line input Lo Line output not switched Ni Neutral input No Neutral output Ls Switched Line output Lc Controlled Line input Photo cell 0 25 2 5 mm f e 10 11 mm LLC7030 Datasheet Outdoor Luminaire Controller DALI User interface The LLC7030 has two pushbuttons One is for testing the lamp driver combination and one to send its unique Neuron ID number to the Segment Controller see Starsense System User Manual for more information The test button can also be used as maintenance indicator2. PHILIPS Status LEDs Power LED Neuron LED Rate Status LEDs Power LED Will show device or output status if it s continuously in blinking mode the OLC is in error mode consult your local Philips representative Neuron LED Will show when Neuron ID is send The yellow service LED indicates the internal OLC state ON Application less The OLC has only communication parameters loaded Unconfigured This OLC state indicates that tt has communication parameters and an application program and network address information This OLC state is the idle state Commissioning and configuration need to be performed Configured Blinking OFF From the factory the OLC is configured for a default lamp and is operating normally LED and 2 will show which output is switched ON 3 5 Test button e Pressing the test button while the output is OFF will switch the output ON for 15 minutes at maximum The output will be turned OFF after the timer has expired During this period the red LED blinks slowly Pressing the test button while the output is at maximum level will cause the output to switch for 15 minutes at dimmed level The output will be turned OFF after the timer has expired During this period the red LED blinks rapidly Pressing the test button while the output is ON at a dimmed level will switch the output OFF A Attention The OLCs output will be switched OFF after 15 minutes Power c
3. LLC7030 Datasheet Outdoor Luminaire Controller DALI CENNE NENE E amd x Dimensions in mm CE 1 5 General Description The Outdoor Luminaire Controller OLC is a high performance LonWorks network device that connects to a lamp driver combination to control and monitor Communication with the OLC is established via the power line utilizing the LonTalk open protocol It interacts with the lamp driver by means of a DALI interface and when needed switching its output Because of the DALI interface it is possible to control more lamps with less OLC s compared to the 10V OLC The OLC makes use of the DALI commands and therefore extra data from the driver will be available in the Starsense system The OLC can autonomously switch its output ON and OFF if combined with a photocell The OLC is designed to work in combination with the Philips Segment Controller SC in a Philips Starsense outdoor lighting telemanagement system Applications Each LLC7030 is able to monitor and control up to two independent lamp driver combinations It is designed for use in highway residential street and road lighting applications including parking lots ports train stations and industrial complexes The design of the OLC is optimized for mounting within a luminaire It is recommended for optimal performance to connect not more than 70 OLC s to one SC if the two DALI out
4. NSI EIA 709 2 CENELEC consumer band C band 132 5kHz automated B band OkHz selection if communication on C band fails FCC and CENELEC EN50065 compliant RoHS directive 2002 95 EC REACH SVHC Internal band stop filter to filter interference from the lamp driver Compliant to IEC 60929 2004 Annex E 2 individual digital control outputs 8mA per output Suitable for magnetic relay type photocell without snubber This LED is on when the OLC has power This LED is normally off Blinking indicates that the application is in un configured state 2 red LEDs labelled and 2 which indicate the output state of DALI output and 2 Send Neuron ID Change output states and 2 100 50 OFF Code 28 Neuron ID Accuracy 0 7 Max value pre fuse 6 ATH 5 5 Housing Material Bayblend KU 2 1514 PC ABS Blend Flammability UL 94V 0 at 5mm thickness 850 C P20 in any position P22 in upright position Glow wire test Protection class Dimensions H 15 6 cm W 6 3 cm D 6 3 cm Weight 0 31 kg Standards Safety EN61347 2 Immunity EN61547 EN50065 2 Emission CISPRI5 edition 7 1 LONWonkks and Neuron are trademarks of the Echelon Corporation registered in the United States and other countries LONMARK SPONSOR Packing data Type Box dimensions Qty Material Weight Kg mm net gross LLC7030 OLC DALI 295 x 385 x 165 24 cardboard 499 5 08 Ordering Data Type MOQ O
5. Powering the OLC ON Apply mains power to the OLC once it is mounted securely and all its wiring is connected as shown in the typical wiring diagram After power up both red LEDs will come ON for 3 seconds The unit is fully operational and ready for commissioning and configuration after both red LEDs go OFF The green power LED should stay ON continuously indicating that power is applied and the OLC is running in a correct mode The OLC is now in its default configuration The safe guard mechanisms burning hours counter power up behavior and manual interfaces are operational Status messages The OLC continuously monitors the current internal temperature Each newly generated status message is time stamped Only the last two status messages are available via power line messages Energy consumption and burning hours are stored in non volatile OLC memory and can be obtained together with status messages by the SC and Starsense Supervisor software Safe guard mechanism with photocell The OLC can configuration property fall back onto photocell operation when it detects a communication failure with the SC This safe guard mechanism prevents light points from staying OFF during the night causing dangerous situations and from staying ON during the day which would waste energy The OLC is equipped with one single pole 230VAC input to monitor the photocell operation When in safe guard mode the OLC will follow the photocell input with its o
6. ckup scenario safeguard mechanism is available and can be configured in different ways Refer to page 4 of this document and the Starsense Configurator Manual for more information on this topic Repeating The OLC is equipped with a power line transceiver which can repeat messages The SC monitors and controls the dynamic repeating functionality centrally If communication fails between the SC and a specific OLC another OLC can be designated dynamically by the SC which can repeat messages The SC will autonomously and continuously keep track of which OLC s can be reached directly and which ones require message repeating Mounting information The OLC is designed to be installed inside a luminaire but can also be mounted in the pole geartrays and separate boxes If the OLC is mounted inside a pole it may only be mounted upright The OLC may be mounted in any position if the enclosure is IP43 or above Please also refer to the installation instruction of the LLC7030 Released drivers Currently the lamp drivers released to interact with the DALI outputs of the OLC are e PHILIPS HID DV DALI 100 150W SON CDM with lamps SON and CDM TT e PHILIPS HID DV DALI Xtreme driver with CPO Cosmopolis lamps 60 90 140 W e PHILIPS HF Regulator II Touch and DALI for PL L PL T PL C lamps Any other component must be validated before it may be used with the OLC Contact your local Philips representative about how to obtain component validation
7. puts are used so 140 drivers or 140 OLC s if only one DALI output is used The Philips OLC is released and authorized to solely interact with the Philips SC consult the local Philips representative if desired otherwise When you switch the lamp driver on off by a DALI command there is the possibility to use the Switched Line Output for another type of load like an advert light or Christmas lights The LLC7030 OLC DALI doesn t measure energy consumption this information is gathered from the driver For advanced metering you may use the LLC7035 OLC DALI that integrates a meter chip with high accuracy energy metering K Tip The Philips Starsense system uses the Philips Starsense Configurator and Supervisor software The license to use this software is embedded in the Segment Controller PHILIPS LLC7030 Datasheet Outdoor Luminaire Controller DALI General operation The OLC combines three main functions The controller function receives the incoming commands from the SC and acts accordingly 2 The OLC switches the Line Output and communicates with the lamp driver via the DALI interfaces 3 The monitor function reports data on current mains voltage mains frequency power factor burning hours and power consumption of the connected lamp driver combination This information is used to determine condition of the lamp driver combination A default configured OLC will switch ON its output at maximum level on power up A ba
8. rdering number EAN code level EAN code level 3 EOC LLC7030 OLC DALI 9137 003 38703 87115 59732817 87115 59732831 732817 99 322 636 36123 PHILIPS 03 201 Data subject to change www philips com lightingcontrols
9. tive humidity Max housing temperature Mains voltage Nothin jesus 25 C to 70 C 10 to 90 75 C onTc spot see OLC cover If the Tc rises beyond 85 C during use the OLC will switch off the relay load Non operating conditions Temperature Relative humidity Mains connection Mains voltage Mains frequency Max load wattage Power consumption tand by wattage wn Connector block Mains connector Wire cross section mm Wire cross section AWG Wire strip length 40 C to 85 C 5 to 90 220 240V 10 50 60 Hz 5 1000W 2 x 400W DALI drivers including advert light lt 2W WAGO 804 series contact cage clamp connection 0 25 2 5 mm solid 0 25 2 5 mm fine stranded 0 25 1 5 mm fine stranded with ferrule and plastic collar 0 25 2 5 mm fine stranded with ferrule without plastic collar 20 12 AWG solid 10 1 mm LLC7030 Datasheet Outdoor Luminaire Controller DALI Power line interface Channel type Coupling Protocol Power line transceivers Frequency band Approval Filter DALI interface nterface Number if interfaces Max load Photocell input nput Indicators Power LED green Service LED yellow Output LED red 2x Manual controls Service button yellow Test button orange Barcode code Back up scheduler Safety pre fuse requirement PL 20C power line Line to Neutral Non lsolated Coupling ANSI EIA 709 Compliant to A
10. utput A factory default OLC will switch to the safe guard state if a 230VAC voltage level is detected on the photocell input Note It is only possible to connect photocells which use an electromagnetic relay Door open detection The photocell input can also be used as a door open detector Refer to the Starsense System User Manual on how to configure and use this feature Safe guard mechanism with back up scheduler When no photocell is being used the back up scheduler can be used The OLC can configuration property fall back to run according to a pre configured schedule when it detects a communication failure with the SC The OLC will use this back up schedule to switch its output It runs on tts own internal real time clock if it is in this stand alone mode The switch ON level can be pre configured through the OLC power up value 4 5 Daylight control based on photocell operation When in daylight control mode configuration property the OLC will follow the photocell input with its output while still receiving and executing the dimming levels from the segment controller In this way the switching points are controlled by the available sunlight and the light level is controlled by the Starsense system Lamp ballast monitoring is enabled within daylight control The following functional table is foreseen for photocell use Dusk Dawn Closed Open Technical data Operating conditions Temperature Rela
11. ycle the OLC to have the output automatically switched to its configured power up level Maintenance identification After maintenance has been done on an OLC press the test button for 4 seconds an identification message will be send via powerline and will be made visible in the supervisor software Neuron ID Each OLC has a unique fixed 48 bit identifier called Neuron D The Neuron ID is printed on the three barcode labels placed on the front of the OLC which barcode readers can read OLC LLC7030 00 8222 740 39903 U 220 240V fa 50 60Hz P max 1000W TE war ORE IBS IP 20 made in E U www philips com CE To prevent water traps do not mount the connectors upwards vel Datasheet Housing provides insulation for class DA is internally connected to Neutral Ni 000981379400 000981379400 000981379400 OLC label A Attention When the OLC is installed it is vital for the Starsense system operation that it knows the Neuron ID and the location of the device A drawing or list indicating which Neuron ID belongs to which installed OLC acts as an input for creating the Starsense telemanagement configuration off line K Tip See Starsense System User Manual for usage suggestions LLC7030 Datasheet Outdoor Luminaire Controller DALI
Download Pdf Manuals
Related Search