Motocaddy S7 Remote User Manual
Contents
1. FA MOTOCADDY S7 REMOTE Electric Trolley Instruction Manual Before using the S7 REMOTE for the first time please take a few minutes to f read through this manual to ensure that you get the most out of your trolley REGISTERONLINE www motocaddy com warranty Locating your Serial Number Attaching the Wheels Attaching the Anti Tip Wheel Locating your Serial Number The serial number for your Motocaddy trolley is located on the underside of the battery tray This number is required when registering your warranty online and should be kept handy for future use The same number should also be on the box received with your trolley Please ensure you keep hold of the packaging in case you need to return your trolley for any reason A proof of purchase must also be kept in case your trolley requires servicing during its warranty period Please keep a record of your trolley serial number here for future reference MESSI Ls Attaching the Wheels To attach the main rear wheels follow these simple steps 1 Push the quick release button in towards the centre of the wheel 2 Slide the wheel on to the axle as far as it will go 3 Release the button and pull the wheel outwards slightly to lock 4 A small click will confirm they are in the correct position The outer groove can be used as a free wheel option if you run out of battery power during a round of golf IMPORTANT To check you have attached the wheels correctly ont2. 3 Battery Care and Advice All batteries must be charged as soon as possible after each use Please ensure that only batteries supplied by Motocaddy are charged with Motocaddy chargers Cyclic battery chargers are designed specifically in accordance with the battery manufacturer s requirements The Lithium battery charger MUST NOT Fig 1 Fig 2 be used to charge any other battery and is designed for use with Motocaddy Lithium batteries only The charger should only be connected to an earthed socket outlet the battery charger should only be opened and maintained by authorised personnel Unauthorised opening will invalidate your warranty The battery must be stored and charged on a dry non carpeted surface and charged at temperatures ranging between 10 C and 30 C Charging above or below these temperatures is not recommended as it can reduce the battery capacity When connecting your battery to the trolley please ensure that the connections match up black to black and blue to blue Fig 3 Charging your Lithium Battery Caring for your Lithium Battery Caring for your Lithium Battery Charging your Lithium Battery 1 Unplug your lithium battery from your trolley This should always be done before folding the trolley to avoid damage to the battery and or trolley 2 Plug the charger into your mains supply Attach the battery cable to the charger matching the black and blue connections 4 When the charging led indicator has tu
3. and unfold it quicker than ever before Unfolding your Trolley 1 Press and hold the upper QUIKFOLD release button fig 1 2 Lift the handle and release the button 3 Unfold the upper frame section fully fig 2 4 Lift the main frame from the central hinge using the section marked Hold Here until the QUIKFOLD lock clicks into position fig 3 5 Unfold the upper bag support Fig 1 Fig 2 Fig 3 Folding your Trolley 1 Make sure your battery is unplugged before folding Ensure that the upper bag support has been folded up 2 3 Press and hold the lower QUIKFOLD release button fig 1 4 Lower the main frame fig 2 and release the button 5 Fold the handle towards the front wheel until the QUIKFOLD system clicks into position fig 3 You may need to gently push as indicated if you do not hear a click fig 4 Fig 1 Fig 2 Fig 3 Fig 4 Using the Lower Bag Supports Using the Lower Bag Supports This Motocaddy trolley is fitted with the new EASILOCK bag attachment system If you are using an EASILOCK compatible cart bag please follow these simple instructions 1 Remove the two pre fitted lower bag straps by depressing the rear button and sliding fig 1 2 Match up the indicating line on your cart bag with the line on the lower bag support 3 Lower bag until the pins lock in position If you are using a non EASILOCK bag please use the following instructions 1 Stretch the elasticated
4. life of your lithium battery Please ensure that the charger is ALWAYS disconnected from the battery after charging Lithium Battery Management System BMS Motocaddy Lithium Batteries are fitted with a comprehensive battery management system BMS to protect the battery from excessive abuse high currents deep discharge and overcharge When the battery is delivered there may be no output as the BMS is designed to maximize safety whilst shipping Please ensure that the battery is fully charged prior to connecting it to your trolley as this will activate the BMS and effectively switch on the battery From time to time at deep discharge or long term storage the BMS may switch off the battery A full battery charge will rectify this problem Motocaddy golf trolleys are designed to work with the BMS system installed in the Lithium batteries and the voltage meter is also synchronised to work in conjunction with the battery If for any reason the voltage on the battery reaches that below the low battery warning on the trolley then the BMS may disable the battery to protect it Again if this occurs please recharge fully Please be aware that Lithium batteries tend to drop off quickly at the end of the cycle so it is not advisable to attempt to play excessive holes as the BMS will activate for protection purposes Unfolding your Trolley Folding your Trolley This Motocaddy trolley is fitted with the QUIKFOLD system allowing you to fold
5. similar to plugging the device into a PC The USB charger takes power from the main trolley battery and continuous charging will reduce the battery capacity between charges The trolley is designed to disable the USB port when the battery capacity reaches a preset level Hints amp Tips Declaration of Conformity Hints amp Tips e Please unplug the battery when leaving the trolley unattended e The S7 REMOTE is designed for use on mown grass areas and designated pathways Do not attempt to steer the trolley through bunkers or deep puddles Do not try to drive the trolley down steps or high curbs e Avoid overloading your bag as extra weight will increase the consumption of the battery capacity It will also affect the speed and steering characteristics of the S7 REMOTE Very heavy bags will also add unnecessary strain on the motors e Keeping the S7 REMOTE to fairways will help conserve your battery Operating the trolley through long grass and rugged terrain will increase the power consumption Ra DECLARATION OF CONFORMITY kerm Saeed abh ma 2 rln ar ee LE L Th Dk Ca an Him mii AEF age aay efor ture rile Le Ropu beet Dee Be Be Gaii el E y Pn Me a pE ee te Be ee end Bees ha ever Seer pees el eee eee See Listes mors Tr anpes Mpi pe feng er Poa Dare RA Weni y Pe Ba FALRA P Tepe LE bpn Dha Eee EN FH M UP bes Po Fiama al Se lie Sp UITE irae ai e Bim ri LAERE man oe a8 Lay Tel Cee e Gee G
6. trolley using Manual Control mode Using the Tilt Compensation feature Setting Tilt Compensation Pairing the Remote Control In the unlikely event that the remote is not responding or you have a new remote handset it will need to be paired to the trolley To pair the remote to the trolley 1 Press and hold the Speed dial on the handle whilst plugging in the battery 2 When P is displayed on the screen fig 1 release the button 3 Press the Function button on the remote handset rig The handle display will show an r fig 2 to indicate that pairing has been successful Operating the trolley using Manual Control mode When required the S7 REMOTE trolley can be switched to manual mode and operated using the speed dial on the handle To switch to manual mode press the speed dial until the display changes from r to 4 fig 3 This indicates that manual mode has been initiated Fig 2 In manual mode the trolley has 9 speed settings 1 to 9 with 1 being the slowest setting and 9 the fastest To increase the speed rotate the speed dial clockwise or anti clockwise to decrease the speed To start the trolley simply select your required speed setting and press the button The trolley will smoothly accelerate until it reaches the selected speed To stop the trolley simply press the button again there is no need to reduce the speed setting Press any button on the remote control handset to re
7. Your Motocaddy trolley is designed for the transportation of golf bags and clubs contained within Using the trolley for any other reason may cause damage to the trolley and cause harm to the user Do not attempt to transport any other equipment The trolley is not designed for the transportation of people Do not use the trolley to assist you when going up hills Never aim the S7 REMOTE at other people or golf trolleys Submerging the trolley in water eg a lake is likely to cause damage to the trolley Do not operate the trolley whilst under the influence of drugs or excessive amounts of alcohol The battery must be disconnected from the trolley before transporting When using the S7 REMOTE in confined spaces for example car parks or near water such as over bridges it is advisable to use the Manual control mode to ensure that you remain in control of the trolley Never let the S7 REMOTE run out of your sight Always use proper care and control Motocaddy cannot take responsiblilty for any damage or injury caused from improper use Safety Features Caring for your Trolley S7 REMOTE safety features The S7 REMOTE trolley is fitted with safety cut off features Whilst operating the trolley via the remote control if no command is sent to the trolley any buttons pressed for longer than 45 seconds the trolley will cut power to the motors Whilst moving if the trolley travels out of range of the remote control the trolley will also cut p
8. ees ome ae pee fees Peed Fm ee Lh al ee eed pores ef fee hry Dee ees E Gage Tee Se m eraa r See a E Senet Cerren be P er Lip ca bee nier Sih Toa oer epee ieee eee et e T pa do han FA MOTOCADDY Motocaddy Ltd Units 15 18 Stansted Distribution Centre Start Hill Great Hallingbury Hertfordshire CM22 7DG t 44 0 1279 712 370 e info motocaddy com w www motocaddy com a We are dedicated to protecting the environment and encourage the recycling of Motocaddy products through a free tJ collection and disposal service To find out more or to locate your nearest Motocaddy recycling point please contact us through our website MC 15 26 003
9. ivity to provide responsive navigation A light pressure will offer a gradual adjustment in direction and a firmer pressure will result in an increased degree of turn Power and Battery Level There are two LED indicators located below the main display These will illuminate when the battery oa fe The indicator light on the remote control changes depending on the amount of pressure applied Lighter pressure will show is plugged in a green LED and firmer pressure will show a red LED Checking the indicator light during the first few uses will help you get used to the two levels of steering The left LED will display green to indicate that the trolley is under power It will then flash red when the When the trolley is stationary pressing the Minus button will put the trolley into reverse Whilst reversing pressing the trolley receives a signal from the remote control same button will increase the speed and the Plus button will slow it down The right LED displays the battery capacity green amp red Press the Pause Resume button to stop the trolley The trolley is designed to protect the battery from being fully discharged If the battery capacity drops too low i It is recommended to operate the trolley at slower speeds whilst reversing the trolley will cut power to the motors This will be indicated by a b on the screen and the right LED flashing red Pairing the Remote Control Operating the
10. o the inner groove you will find they will not rotate freely in either direction Attaching the Anti Tip Wheel The Anti Tip wheel is designed to prevent the trolley from tipping backwards on steeper inclines and it is recommended that the wheel is ALWAYS fitted when navigating using the remote control handset To attach the wheel simply lift the orange button at the rear of the battery tray fig 1 and slide the wheel attachment into the housing with the hole facing upwards There will be a click when the wheel is fitted securely in place To remove the wheel lift the orange button and slide the attachment out of the housing The Anti Tip wheel can be removed for cleaning and storage purposes Fig 1 Installing Handset batteries Fitting Handset belt clip Battery Care and Advice Installing the Remote Handset batteries The remote handset requires 3 AAA Batteries Included with the manual To fit the batteries Remove the two screws on the back of the handset fig 1 using a Phillips screw driver Lift and remove the back cover Insert the three batteries as shown fig 2 a a E Replace the back cover ensuring the top hooks in to place and secure with the two screws Fitting the Remote Handset belt clip The remote handset comes with an optional belt clip To fit the belt clip to your handset 1 Remove the rubber bung by lifting it out 2 Place the clip in to the back and rotate 90 clockwise to secure fig
11. ower to the motors Whilst operating the trolley in manual mode if no adjustment to the speed is made via the dial for longer than 75 seconds the trolley will cut power to the motors If any of these safety features initiate simply press the Pause Resume button to continue using the trolley Caring for your Trolley Although your Motocaddy Trolley has been weatherproofed please follow these simple guidelines to help protect your trolley e Do not store your trolley outside e Try to minimise exposure to rain as much as possible with an umbrella during heavy rainfall e Wipe excess water from the trolley prior to storage e Never use a pressure washer to clean your trolley To prevent water damage wipe it down with a damp cloth e Avoid using high pressure air hoses near moving components This Motocaddy trolley is designed to require very little maintenance we do however recommend giving your trolley regular checks to ensure e There is no build up of excess mud and dirt e The front wheels are not clogged up and turn freely Only original Motocaddy parts should be used when repairing your trolley S7 REMOTE Equipment Overview Remote Control Overview S7 REMOTE Equipment Overview Digital Control Panel MOTOCADDY Upper Bag Support m7 QUIKFOLD Upper Release Button QUIKFOLD Lower Release Button Rear Wheels Rear Wheel Release Button EASILOCK Lower Bag Support Battery Remote Control Overview 1 Pause Resume B
12. rned green the battery is fully charged and ready to be used JE RED Battery Charging gt gt GREEN Battery fully charged and ready to be disconnected 5 The charging process will take between 3 to 5 hours depending on the depth of discharge please be aware that this may take longer for the first few charges 6 Once charging is complete please disconnect the charger from the mains power supply 7 Finally disconnect the charger from the battery Caring for your Lithium Battery e Try to avoid getting the battery too wet i e do not submerse the battery try to avoid deep puddles and do not clean your trolley whilst battery is still in the battery tray e Dropping the battery may cause damage to the internal cells e Do not lift or carry the battery by the cable e Use a damp cloth to clean off any dirt Recommendations for the hibernation of Lithium Batteries during Winter months If for any reason your lithium battery is not going to be used for lengthy periods e g 3 months over the winter it is advised to store the battery half charged To do this simply use the battery for a round of golf as usual and charge it for 1 5 hours at the end of the round Before the battery is used again recharge it top it up prior to use We recognise that extended absences are not always planned in advance however when it is likely that you will not be using your battery for a period of time it is good practice to follow these steps to extend the
13. rolley until the lines have stopped moving and the factory reset is complete as it may affect the calibration Fig 3 Using the Trim function to reduce veering Using the USB Charging Port Using the Trim function to reduce veering The trim function on the S7 REMOTE trolley can be used to rectify veering caused by factors such as uneven weight distribution of the bag To adjust the trim simply hold down the Function button and press the Left lt or Right gt buttons to trim the power delivered to each motor Pressing the Left lt button will compensate for a trolley veering to the right and vice versa During this process the level of trim will be indicated by the green LED s on the handle and show whether the trim is set to the left left LED or right right LED Holding down the Function button will show the direction that the trolley is currently trimmed to Please note The trim level is not applied whilst operating at low speeds Using the USB Charging Port This Motocaddy trolley features a USB charging port designed to power GPS devices during your round Simply remove the covering cap and plug a USB cable into the charging port located on the underside of the handle The device will continue charging for the duration of time that the cable is attached and the battery is connected It is important to note that the speed of charge will be lower than that of a mains AC charger and
14. strap around the bag 2 Loop the rounded bar underneath the hook fig 2 3 Position the two placement straps centrally on your cart bag fig 3 Please ensure the straps are hooked in place securely before releasing Failure to do so could result in injury to the user Using the Upper Bag Supports Adjusting the Bag Supports Using the Upper Bag Supports The upper bag support straps can be secured using the same steps as the non EASILOCK instructions overleaf Fig 1 1 Stretch the elasticated strap around the bag ik 2 Loop the rounded bar underneath the hook fig 2 left 3 Position the two placement straps centrally on your cart bag fig 3 left Adjusting the Bag Supports The bag support straps are manufactured from elasticated material to allow your golf bag to be held tightly in place The strap should be adjusted to be reasonably tight around the golf bag 1 Unclip the elasticated straps from the housing by pulling outwards in the direction shown by the arrows fig 1 2 Move the bar as required to tighten or loosen the strap fitting Pulling the bar downwards will tighten pushing it upwards will loosen fig 2 3 Ensure that the straps are clipped back in to the housing before use fig 3 Fig 3 Fig 3 Safe use of your Trolley Safe use of your Trolley The following is not intended to cover all possible situations Caution and common sense should always be used when operating the S7 REMOTE
15. turn to remote mode Fig 3 ake a Ks Using the Tilt Compensation feature The S7 REMOTE is fitted with an innovative tilt compensation feature which helps keep the trolley running in a straighter line whilst traversing slopes This will reduce the amount that the trolley pulls down the slope By default the tilt compensation feature is disabled and can easily be enabled It is advisable to try using the trolley first before enabling the tilt compensation The tilt compensation status is indicated by the decimal point shown on the display fig 1 If the decimal point is showing the tilt compensation feature is enabled if it is not displayed then it is disabled Fig 1 To enable disable the tilt compensation feature hold down the Function button and the Pause Resume button simultaneously for 3 seconds The decimal point will appear disappear to indicate that it has been enabled disabled Setting the Tilt Compensation default level It is possible to perform a factory reset on the tilt compensation to instruct the trolley what level ground is This MUST be performed on a completely flat and level surface Fig 2 1 Hold down the Speed dial on the handle for 10 seconds until F fig 2 is displayed 2 Release the button It will take a few seconds to register and a series of lines will move up the display fig 3 to indicate that calibration is underway It is important that you do not touch the t
16. utton Function Button Plus Button Sat oe er ee ee YS Left lt Button 9 Battery Tray 10 Motors located under Battery Tray Right gt Button 11 Front Wheels 12 Battery Connector 13 USB Charging Port 14 Anti Tip Wheel 15 Ant Tip Wheel Release 2 3 4 Minus Button 5 6 7 Indicator LED Using the S7 REMOTE Power and Battery Level Operating the trolley using the Remote Control handset Using the S7 REMOTE trolley Operating the trolley using the Remote Control handset The first time you use the S7 REMOTE we would advise using it on an open area of grass The trolley speeds and steering characteristics will vary depending on the surface To start the trolley moving for the first time press the Plus button on the remote control handset The Plus and Minus buttons can then be used to increase and decrease the speed to the required pace The S7 REMOTE will turn much quicker on hard smooth surfaces and will behave differently on grass You will also find that the weight of the golf bag will affect both speed and steering The trolley can be stopped and restarted by pressing the Pause Resume button It is not necessary to reduce the speed before stopping however it is important to remember that the trolley will restart at the previously set speed The Left lt and Right gt buttons are used to steer the trolley and incorporate dual pressure sensit
Download Pdf Manuals
Related Search