Remote communication manual
Contents
1. Operation command syntax An operation command is prefixed by character op followed by control commands and settings separated by space blank SP and ended by carriage return pair CR and ASCII hex OD Syntax of serial control commands op SP lt operation commands gt SP lt Setting Value gt CR op A constant indicating this is an operation command SP Indicate one blank space CR Indicate the command ending carriage return pair CR and ASCII hex OD Setting value Settings of operation command Types of setup strings Characters of settings Description Query current setup Question mark indicates querying current setup Setup lt settings gt Syntax of settings Symbol suffixed with setup values Increase setup order of T Some settings are changed in steps Symbol adjustment items indicates changing one step up Decrease setup order of Some settings are changed in steps Symbol adjustment items indicates changing one step down Execute operation command None Certain operation commands execute after input without further setting or regulators Examples Control items Input command row Projector return message Query current brightness op bright CR OP BRIGHT 101 settings Set up brightness op bright 127 CR OP BRIGHT 127 Set up input signal source to op input sel 0 CR OP INPUT SEL 0 HDMI DDU6871 DW6851 DX6831 DLP P Projector Remote Communication Manual VIVI vitek RKeSeCI Cdilleid2. For details on PJLink standard commands and connection methods please visit the PJLink official web site Control projector with TCP IP communication protocol This projector supports TCP IP communication protocol which enables you to send RS 232 operation commands or simulated IR commands to control projectors connected with RJ45 cable via terminal connection application software e g Tera Term Please set up IP address and port number with the terminal connection application software before controlling your projector with TCP IP communication protocol IP Address IP address of projector Port Please set transmission port number to 7000 See the section on serial interface RS 232 control commands for details on RS 232 operation commands or simulated IR commands 17 i DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek About the VIVITEK support If you cannot find solutions from this user guideline please contact us using the contact information below North America Vivitek Service Center 15700 Don Julian Road Suite B City of Industry CA 91745 U S A Tel 855 885 2378 Toll Free Email T services1 vivitekcorp com URL www vivitekusa com Europe and Africa Vivitek Service amp Support Zandsteen 15 2132 MZ Hoofddorp The Netherlands Tel 31 20 655 0960 Email support vivitek eu URL www vivitek eu China Vivitek Service Center 201209 Room 1802 18 F Cimic Tower No 1090 Centu
3. Manual WVIVICE kK Operation Settings return values command Sharp sharp Do not apply when the project is in 0 31 standby mode or the input signal is not locked yet Noise Reduction gt Do not apply when the project is in 0 15 Noise Reduction standby mode or the input signal is not locked yet Aspect Ratio aspect a Do not apply when the project is in 0 5 4 standby mode or the input signal is 1 4 3 not locked yet 2 16 10 When the Zoom function is set to 3 16 9 Zoom in the Unscaled function is 4 1 88 disabled 5 2 35 6 Letterbox 7 Native 8 Unscaled Overscan zoom Do not apply when the project is in standby mode or the input signal is not locked yet b When the Aspect Ratio function is set to Unscaled the Zoom function is disabled Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet b Apply for VGA and Component signal input Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet b Apply for VGA and Component signal input Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet b Apply for VGA and Component signal input Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet b Apply for VGA and Component signal input auto img execute Do not apply when the project is in standby mode or the input signal i
4. not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Saturation Magenta Saturation Yellow hsg c hue O DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual WVIVICE aS a command Hue Magenta hsg m hue Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Hue Yellow Hsg y hue Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet White Blance Red hsg wr gain Do not apply when the project is in Gain 0 200 standby mode or the input signal is not locked yet White Blance Green hsg wg gain Do not apply when the project is in Gain 0 200 standby mode or the input signal is not locked yet White Blance Blue Hsg wb gain Do not apply when the project is in Gain standby mode or the input signal is not locked yet LAMPS a command Lamp Mode lamps a Do not apply when the project is in standby mode b Do not a
5. not apply when the projector is in 80 80 standby mode 080 funeon Operation Settings return values command Mode eco net pow O Off Standard Standby Mode 1 On ECO Standby Auto Power Off auto powoff Do not apply when the projector is in standby mode a IP net _ La ane a net lena lt String gt Gateway net gateway an net ee Bi Ni tl ON NS ii D r Off 1 On a Rate a speed This command is not required as the 0 115200 bps setting is default to 9600 when 1 5 7600 bps RS232 commands are sent to the 2 38400 bps projector through RJ45 cable by 3 19200 bps external integrated video and control 4 14400 bps signal transmission box 5 9600 bps 6 4800 bps 7 2400 bps 8 1200 bps O Pekoso uncon T 0 DLP Projector Remote Communication Manual VIVIE kK Settings return values command T 7 ain Logo startup eal nl trig a Auto en ee src aa Black dblack r 3D Format 3d format DLP Link 3d diplink E 3D 24Hz Display 3d 24 This setting is default to 9600 when RS232 commands are sent to the projector through RJ45 cable by external integrated video and control signal transmission box 0 Local 1 Digital Off es On Do not apply when the projector is in 0 5 4 standby mode 1 4 3 2 16 10 3 16 9 4 1 88 5 2 35 6 Letterbox 7 Native 8 Unscaled h Auto r Off st
6. andby mode 1 On 0 Off standby mode 1 On Do not apply when the project is in standby mode or the input signal is not locked yet 0 Off 1 Auto 2 Side by Side 3 Top Bottom 4 Frame Sequential Do not apply when the project is in standby mode or the input signal is not locked yet Do not apply when the project is in standby mode or the input signal is not locked yet a Do not apply when the project is in standby mode or the input signal is not locked yet b Apply to input signal 3D 24Hz only 0 Normal 1 Reverse 0 English 1 French 2 Spanish 3 German 4 Portuguese 5 Chinese Simplified 6 Chinese Traditional 7 Japanese 8 Korean DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI vitek a e model lt String gt o Serial Number lt String gt ooo d O pswver lt String gt o o O zo Pixel Clock pixel clock lt String gt a In unit of MHz b Do not apply when the project is in standby mode or the input signal is not locked yet an signal pee Do not apply when the project is in standby mode or the input signal is not locked yet H ee Rate h refresh Do not apply when the project is in standby mode or the input signal is not locked yet V Refresh Rate v refresh lt String gt Do not apply when the project is in standby mode or the input signal is not locked A Lamp1 Hours lamp1 hours lt String gt Lamp2 Hours impr g
7. ector for networking In case the remote network control is not connected to LAN or DHCP or the LAN is not activated connect as illustrated below INPUT PICTURE LAMP ALIGNMENT SERVICE Eco Network Power lt Standard gt Network Auto Power off lt Off gt IP Address lt XXX XXX XXXX XXX gt Auto Power On lt Off gt Subnet lt 255 255 255 0 gt Projector Control lt Both gt Gateway lt XXX XXX XXXX XXX gt Network Enter DHCP Off RS232 Enter Apply Apply Startup Logo lt Off gt Trigger lt Off gt Auto Search lt Off gt Dynamic Black lt Off gt 3D Enter Language Enter Caution In case the remote network control is not connected to LAN or DHCP or the LAN is not activated set DHCP option to Off and then select Apply The DHCP service assigns IP address and settings to devices automatically and keeps IP Address Subnet and Gateway options away from editing In case the DHCP service of the LAN is not activated set up the network manually Use A V and the Enter button to select Network and network settings IP Address To specify an IP address press the Enter button to show the IP address input window Use the lt gt button to select the number in the address to be changed Use the A Y button to increase or decrease the number in the IP address IP Address 172 XXX XXX XXX Subnet Set the subnet The input method is the same as the IP address Gateway Set the gateway The input met
8. ends email via a SMTP server Set up transmission port Input target user name for the projector to send the reminder email to through a SMTP server Input user password Enable or Disable reminder email Set up email address of the email sender Set up email address of the email recipient Set up email address of the email CC recipient Set up projector name or ID Set up projector installation location Confirm your settings Press this button to save changes you have made Send test email The reminder email is sent only in the event of a projector error Press this button to validate email settings after setup is completed 15 i oo ee ee al Aaa v v v Click the Crestron option in your project s wen server homepage The Crestron control page displays in new tab Tools Info Contact IT Help Menu A Auto 4 Enter ke Blank v Contrast Brightness sharpness E CRESTRON Power Press this button to power on or off the projector Source List Switch projector input signal sources Press the A or V arrow key to scroll through the dropdown list of available signal sources Image adjust options Press the lt or gt arrow key to scroll through available adjustment options Freeze Freeze current projection screen The projection screen prompts the Still open message after the freeze function enabled Press the Freeze button again to unfreeze the screen Contrast Click this button and the adjustment window displays C
9. hod is the same as the IP address DHCP Enable or disable the DHCP service When DHCP is set to ON the DHCP server of the domain will assign an IP address to the projector The IP address will appear in the IP address window and you don t need to make any input Otherwise the domain does not or cannot assign any IP address and 0 0 0 0 is shown on the IP address window Apply Select this button and press Enter It takes the projector several seconds to execute the change of the network setting till the following message disappears Setting network configuration please wait Please contact your network administrator in case the network remains disconnected 13 oom T DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek Control the projector through a network Control the projector through a web browser Open the web browser of your control PC type the projector s IP address the projector s web server homepage displays with the following four options Projector Status Current projector settings Alert Mail Setup Settings for projector abnormality email reminders In case of any abnormality the project sends emails to preset users Crestron Crestron compatible web browser control pages PJLink Set up password for PJLink connection in this page Projector Status Illustration below goes with projector at IP address 192 168 0 100 ae viviltek Projector Status Alert Mail Setup Crestron PILi
10. lick the lt gt arrow keys to adjust contrast Contrast E a Zoom Zoom the projection image Click the key to zoom in and to zoom out You may click the four arrow keys in the window to move the zoomed projection image LOOM 16 Mien U A A uto Enter Confirm and select function options Menu Press to display OSD menu Press again to exit it Auto Run the auto image adjustment function Blank Pause the image projection i e the projection image is masked Press again to resume the projection Source The signal source menu displays Press to display signal source in the projection screen Tool See user manual included with the products you want to use together with your Crestron equipment for its setup Info Display current projector status and Crestron setup Control projector with the PJLink protocol PJLink is a standard designed by the Japan Business Machine and Information System Industries Association JBMA for controlling projectors with genuine commands A PJLink standard compliant projector from any supplier can be controlled with these genuine commands This product supports PJLink control commands Please set up password for PJLink connection in this page r vivitek Projector Status PJLink Security Alert Mail Setup Password Crestron PIJLink PJLink Security Select On to enable PJLink password or Off to disable it Password Setup password at length up to 32 characters
11. ndby mode or the input signal is not locked yet Brightness bright Do not apply when the project is in standby mode or the input signal is not locked yet Saturation saturat c Apply for YUV signal input d Do not apply when the project is in standby mode or the input signal is not locked yet Hue tint a Apply for YUV signal input b Do not apply when the project is in standby mode or the input signal is not locked yet Gamma gamma Do not apply when the project is in 0 Film standby mode or the input signal is 1 Graphics not locked yet 2 Video 3 Linear Color Temp color temp Do not apply when the project is in standby mode or the input signal is not locked yet Trim Red Lift red offset Do not apply when the project is in standby mode or the input signal is not locked yet Trim Green Lift green offset Do not apply when the project is in standby mode or the input signal is not locked yet Trim Blue Lift blue offset Do not apply when the project is in standby mode or the input signal is not locked yet Hue Red Gain red gain Do not apply when the project is in standby mode or the input signal is not locked yet Hue Green Gain green gain Do not apply when the project is in standby mode or the input signal is not locked yet Hue Blue Gain blue gain Do not apply when the project is in standby mode or the input signal is not locked yet O DDU6871 DW6851 DX6831 DLP Projector Remote Communication
12. nk System Model Name Software Version System Status Display Source Lamp 1 Hours Lamp 2 Hours Error Status DU6871 Software Version System Status Display Source Lamp 1 Hours Lamp 2 Hours LAN Version 192 166 0 100 Subnet mask 255 255 255 0 Default gateway 0 0 0 0 DNS Server 0 0 0 0 00 18 23 26 FF 52 Projector model name The version of the software installed in the projector Current projector startup status Display the current source Display the usage hours of Lamp 1 Display the usage hours of Lamp 2 Indicate projector diagnosis message Network control setup message RJ 45 Version LAN Version IP address Subnet mask Default gateway DNS server MAC address Network control software version number Projector IP address setup Projector subnet address setup Projector gateway setup Projector DNS server setup Projector MAC address setup 14 oom T DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VEVI tek Projector Status Alert Mail Setup Crestron PJLink User Name Password E mail Alert Enable Disable From To Cc Projector Name Location Apply This projector can send emails with projector abnormality messages to preset users Set up the projector before enabling this function SMPT Server Port User Name Password E mail Alert From To CC Projector Name Location Apply Send Test Mail Set up SMTP server name as the projector s
13. oom DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek Table of Contents The Serial interface RS 232 command sssccssesesccsseveresessserscesenenscstedevessrentusdessaeencessnsusssiaiencevenstusssssdirecvissessesiedinwets 2 Commun canon pa ameer SUM aa E E E E pessainentosadamin atsents 2 CJPCEALION Commands sse E EE EA E Ea E 2 Operation command Sy 110A secanaasneconocitandatantaesiuacnaenecanoannacisaadatantdesieaateceninakecuaudiunndnbasktanttenunonseonpuadunasenaaahinanseesdonmmensavaptedunesainass 2 EAST Gi operation CO MANES eec e ear a Eaa a EE a Eai 3 simulated IR remote controller commands ssvsssvnccescssvevesverienediedveonnsevierssiss vennsseudeesddedvconnceuseodsiesteonssadsceeldedeeessceuseodsieateonssedseverdedeaes l1 Control the projector through a network ssssssceececccsssssceccocosssssececocosssssceccocosssssseccocossssssceceecssssssseceecssssssssee 12 RAS ONG COIN ac TE NE S E ENEE tien EEE A SANE E EEE AANEEN E AECA ANE 12 Setup ihe projector HOE TC LW OL MIN E ereun eee NEEE EAA EEEE aa En na EEA EEEE ENERE ERRANEN 13 Control the projector through a network ssesisosnsisiasresiniises inoa E AEA EANET aA NAE O SENEE EE ENA NOTATER SEa ESEN 14 Control the projector through a web DrOWSET ccccsssssessesseeeeeceeeeeeeeeeeeesseeeeeseeeeeeeeeeeeeeeeeaaasseessseeeeeeeeeeeeeeeessaaaaagsesseeeeeeeeeess 14 Control projector with the PJLink protocol n nseesenessssssesseeeereesesssssssssss
14. pply when the project is in Please send control command after the said commands are completed Lamp Power lamp mode 0 Standard Do not apply when the project is in 1 Economy standby mode 2 Custom Power Level Custom Lamp Power 0 31 75 100 0 Do not apply when the project is in standby mode 1 On standby mode standby mode ALIGNMENT command Projection Mode proj mode Do not apply when the project is in cooling or lighting up status High Altitude altitude 0 Off Do not apply when the project is in 1 On standby mode standby mode 0 Front 1 Rear 2 Ceiling Front 3 Ceiling Rear 4 Up Front 5 Down Front Zoom Zoomio The camera control command does not apply when the projector is in standby mode O 2 DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual WVIVICE kK pF tt apply when the arceco is in pF nt pp mode Shift V vert a The camera control command does not apply when the projector is in standby mode Shift H horiz offset The camera control command does not apply when the projector is in standby mode Load Memory lens load 1 to 10 The camera control command does not apply when the projector is in standby mode Edit Memory lens save 1 to 10 The camera control command does not apply when the projector is in standby mode Center Lens lens center execute The camera control command does not apply when the projector is in standby mode Do
15. ry Avenue Pudong Shanghai Tel 400 888 3526 Toll Free Tel 021 58360088 142 Direct Email service vivitek com cn URL www vivitek com cn Asia and Taiwan VIVITEK after sales service Vivitek Corporation Co Ltd 4F No 186 Ruiguang Rd Neihu Dist Taipei City 11491 TEL 86 28 797 2088 FAX 86 26 600 2358 E mail kenny chang vivitek com tw URL www vivitek com tw 18
16. s not locked yet hsg r gain Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet H Total h total H Start h pos H Phase h phase V Start V POS Auto Sync Color Red Gain Color Green Gain hsg g gain O DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual WVIVICE kK command Color Blue Gain Hsg b gain Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Color Cyan Gain hsg c gain Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Color Magenta Gain hsg m gain Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Color Yellow Gain Hsg y gain Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Saturation Red hsg r sat Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Saturation Green hsg g sat Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Saturation Blue Hsg b sat Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet Saturation Cyan hsg c sat Do not apply when the project is in 0 200 standby mode or the input signal is not locked yet mM Do
17. seererrrsssssssssssssserrerrrsssssssssssseeetrereresssssssssseseeerereo 17 Control projector with TCP IP communication protocol seeeeeesessssssssseeeeeeereessssssssssssseeteeeersssssssssseseeetreresesssssssssesssereereo 17 ADO EMG VIVE IR SU OF e E EE EE E E E 18 oonm 7 DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek The serial interface RS 232 command This controller supports projectors with a RS 232 serial interface There exist two types of serial commands Operation command Available menu options are INPUT PICTURE LAMP ALIGNMENT CONTROL SERVICE and OTHERS Simulated IR remote controller commands Controls projector with serial command analog IR remote controller and its control keys Communication parameter setup You can use the serial control command to input commands for projector control or retrieve its operational data through Windows client terminal software e g Hyper Terminal with ASCII characters You need to set up the following communication parameters in advance Parameter 115200 default 57600 38400 19200 14400 9600 4800 2400 1200bps 8 bit None 1 Flow Control None Port 7000 Caution The terminal software does not return every command input character The transmission performance varies with the matching length of RS 232 cable and transmission speed Please select proper transmission from the OSD menu Operation commands
18. t Move cursor to the right or change to the right l1 oom DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek Control the projector through a network This machine supports the following methods in remote controlling the projector through a network Control projector through web browser Control projector with RS 232 control or simulated IR commands via TCP IP communication protocol Control projector with PJLink standard commands Cable connection You may connect the projector to a PC or to an external integrated video and control signal transmission box through LAN for remote control Connect the projector to a PC See figure below for connecting the projector to a PC in RJ 45 cable for control For connection through LAN connect the PC to a hub through to the projector s Digital Lan port Digital LAN ZI Connect with an external integrated video and control signal transmission box You may connect the projector to an external integrated video and control signal transmission box with RJ 45 cable for concurrent video and networking control signal transmission Please connect the PC to the input end of the transmission box with one RJ 45 cable and the output end of the transmission box to the Digital LAN input end of the projector with another RJ 45 cable Digital LAN 12 oom T DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek Set up the proj
19. t smp Projecotor Runtime proj runtime lt String gt Blue Only blue only Do not bo not AE when the projector is in 0 Off standby mode 1 On Factory Reset fact reset execute Others command PowerOn power on execute Powerof __ power off_ execute ff Projector Status status 0 standby 1 warm up 2 imaging a cooling reset e p e o aa a a a mmp T e O ot Center Lens lens center___ execute Caution The projector returns string NA when the input command does not apply to current projector status or setup oe E ee HW NEN 10 oom T DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VIVI tek Simulated IR remote controller commands This control command simulates the IR remote controller and its control keys It shares the same syntax of operation command It begins with characters ky followed by control commands and settings separated by space blank SP and ended by carriage return pair CR and ASCII hex 0D Control command syntax ky SP lt operation command gt CR Examples Power On ky power on CR Power Off ky power off CR List of simulated IR remote controller commands Operation Description command 1 Power On power on Power On S Display OSD menu 6 Up_ jup Move cursor upward or change upward __ 8 lef left Move cursor to the left or change to the left 9 Right righ
20. tO Genter OOQSTTOM ens Gente Caution When controlling the projector to execute multiple commands make sure the return message of the last command is received before sending out the next one List of operation commands command Input input sel Do not apply when the project is in 0 HDMI standby mode 1 DVI a Standby mode 2 VGA b When the blank function is 3 Component BNC activated 4 DisplayPort 5 Digital Test Pattern pattern Do not apply when the project is in 0 Color Bar standby mode 1 Cross Hatch 2 Burst 3 Red TI 4 Green TI 5 Blue TI 6 WHITE TI 7 BLACK TI 8 HRamp TI 9 Red uncorrected 10 Green uncorrected 11 Blue uncorrected 12 White uncorrected 13 Black uncorrected 14 Off Color Space color space Do not apply when the project is in 0 Auto standby mode or the input signal is 1 YcbCr Rec 601 not yet locked 2 YPbPr Rec 709 3 RGB PC 0 255 4 RGB Video 16 235 Input Lock input lock Do not apply when the project is in standby mode or the input signal is not yet locked Background no signal Do not apply when the project is in standby mode PO oso Taneton oom T DDU6871 DW6851 DX6831 DLP Projector Remote Communication Manual VEVI tek aN Settings return values command Picture Mode pic mode 0 High Bright 1 Presentation 2 Video Contrast contrast Do not apply when the project is in sta
Download Pdf Manuals
Related Search