- Avanti Online
Contents
1. is properly fixed and that plugs are sitting tight and properly If AVANTI ANCHOR has arrested a fall it may never be used again Marking on Anchor plate Read instructions before use Direction for prevention of fall downward when mounted on ladder AVANTI product name EN standard number Unique identification number gor ANCHOR 1 USER Marking on both sides of clamp This anchor point is only for use in connection with personal fall arrest equipment Connection to a full body harness according to is allowed in the A marked Fall Arrest attachment on front or backside whatever is considered most advantageous It is forbidden to use the AVANTI ANCHOR for attachment of hoists goods or the like AVANTI ANCHOR is tested and approved only to be installed on AVANTI ladders with 60x25 mm stiles and 27x29 mm rungs In case of doubt please contact AVANTI The ladder and its installation must comply with EN ISO 14122 4 and EN 131 in EU and or with ANSI 14 3 in USA AVANTI recommends the owner installer to verify the suitability of the ladder installation for example by consulting the manufacturer or a qualified engineer The installation must be performed by a competent person following the installation form in this manual Before installing the AVANTI ANCHOR in heights assure to be proper secured against fall from height by u2. cts Periodical examination A periodic examination at least every 12 month is essential for the safety ofthe AVANTI ANCHOR The examination must be performed by acom petent person following the inspection form in this manual For the AVANTI ANCHOR the competent person only needs to be trained in any metallic component covered by the European standard norms for fall arrest equipment The result of the periodic ex amination must be recorded in the equipment registration form included in this documentation OK not OK 1 Ladder does not show any deterioration 2 Anchor does not show cracks deformities corrosion or other damages 3 Anchor installed on the ladder according to the instrucions 4 Anchor marking is clearly readable Is the Anchor in good condition to be used Signature of competent Yes Needs Repair Replace Name of competent in capital letters Date Avanti Anchor Identification no Tel 45 48 24 90 24 Fax 45 48 24 91 24 wwwavanti online com Date of purchase Date first put into service Periodic examination and repair history Reason for entry per examination OK not OK Inspector Periodic examination next due date Australia dale OL12 7LQ EE N UK raue Systems Limited E A
3. his her position to minimize the fall distance the most possible in case of a fall The position of the anchor point is crucial in case of a fall arrest the height of the fall elongation of lanyard and energy absorber or pendulum movement of the user should be considered in order to minimize the risk of impact in obstacles in case of a fall It is prohibited to do any modification or use non original AVANTI components when assembling AVANTI ANCHOR Re use of demounted AVANTI ANCHORS or parts is not allowed Any changes or other uses beyond this manual are strictly forbidden The AVANTI ANCHOR is only to be used by one person at atime It is strictly forbidden to carry out climbing or work if the person is in unfit mental or physical condition Climbing and working under the influence of alcohol drugs or any medication which can interfere with the safety are also prohibited Observations Only to be used by instructed workers Only to be used for preventing fall in direction of the arrow Only to be used for fall arrest not to hoist or hang in goods or similar If there are any doubts to the safety of the AVANTI ANCHOR or parts of it aren t properly fixed deformed or damaged with cracks or similar incompatibilities it may not be used Please contact the manufacturer immediately In case of corrosion immediately remove the AVANTI ANCHOR Before attaching to the ANCHOR check that its sitting
4. s according to EN 362 in EU Z359 1 2007 in USA and Z259 12 in Canada User shall be equipped with a means of limiting the maximum dynamic forces exerted on the user during the arrest of a fall to a maximum of 6 Use in connection with other equipment than specified may be potentially dangerous In case of doubt please contact AVANTI The maximum load that can be transmitted in service from the anchor device to the structure is 22 5 kN in 5 vertical direction The maximum deflection of the ANCHOR that can occur in service is 20 mm AVANTI ANCHOR is tested and approved only to be mounted on AVANTI ladders The materials used on the anchor device are stainless steel and PE HD for the locking plug This manual shall be supplied in language of sale Activities at height are dangerous and may lead to severe injury or even death Gaining an adequate apprenticeship in appropriate techniques and methods of protection is important and is your own responsibility Users are obliged to read and understand this User Manual Further they need to be proper equipped and instructed with the use of the necessary fall arrest equipment and emergency procedures in case of injury or sudden illness Users going to install AVANTI ANCHOR need to be familiar with the installation section of this manual It s essential to the safety that the user always attach the energy absorber as high as possible above
5. sing relevant fall arrest equipment 1 Mount the stile clamp on to the stile fig 1 and press the clamp in proper tight position on top of the chosen rung fig 2 2 Insert the anchor plate between stile and clamps fig 3 and pull downwards in the direction of the arrow 3 With a soft face hammer gently tap on top of the anchor until plate and rung openings are aligned fig 4 4 Insert the plugs and gently tap with the soft face hammer fig 5 until plugs are fully seated fig 6 5 Make sure that plugs are fully seated and that clamps fig 7 and plate are in place 6 Carry out the annual inspection by following the procedure in the section Inspection If the ANCHOR gets dirty clean with plain water and wipe water off with a dry rag Store the anchor in a dry environment and always kept away from acid paints or similar During transportation or storage do not squeeze ANCHOR beneath heavy goods Lifetime It is well known that equipment deteriorates progressively in use It is difficult to give an exact lifetime because it depends on the intensity and frequency of use and the environment in which the equipment is used Before use Each time using the AVANTI ANCHOR the user inspects the ANCHOR visual and manually by twisting pulling Check the parts are proper fixed and free of deformities damages cracks or similar unacceptable defe
6. tructions AVANTI ANCHOR SAFETY POINT User s Maintenance and Installation Manual AVANTI ANCHOR SAFETY POINT User s Manual and Installation Instructions Date of publication 2nd Edition May 2013 Manufacturer AVANTI Wind Systems A S Hogevej 19 3400 Hillerod Denmark P 45 4824 9024 F 45 4824 9124 E info avanti online com 1 www avanti online com UKAS um MANAGEMENT 001 AyANTI Established 1885 Declaration of Conformity Manufacturer Avanti Wind Systems A S Hoegevej 19 DK 3400 Hillleroed Phone 45 4824 9024 Fax 45 4824 9124 herewith declares that the model AVANTI ANCHOR conforms to the design requirements for single user anchor devices for use in combination with personal fall protection systems as specified on the following standard EN 795 2012 Personal fall protection equipment Anchor devices Place La Muela Date 03 04 2013 Signature Name Alejandro Rios Nerin 7 Identification Technical Director 12 AVANTI ANCHOR is an anchor point used for protection against falls from heights It is intended for use with an energy absorber approved according to EN 355 in Europe ANSI Z359 1 2007 in USA and Z259 11 in Canada This energy absorber is connected to a full body harness approved according to EN 361 in EU Z359 1 2007 in USA and Z259 10 12 in Canada Connection to the ANCHOR is only allowed by using self closing connector
7. vanti Anchor 01 401 478 www avanti online com info avanti onlin
Download Pdf Manuals
Related Search