XPS Sport EL User Manual(Eng)
Contents
1. TEAM POWERS Designed amp Manufactured by RC EXPLORER TEAM XPS Brushless Speed Control System User Guidelines 1 Technical Specifications BEC Output Linear 6V 2A Linear 6V 2A Linear 6V 2A Dimension L x W x H mm 32 x 30x28 32x30x28 32x30x28 Foo E a a Motor limit with 2cell x 3 7V Lipo 4 Tum orover 6 5 Turn or over 9 5 Turn or over uestes 777 fn 2 Features Support all kinds of sensor sensorless brushless motors in RC model 1 10 1 12 Car amp Truck Support Running Mode Forward with brake Forward Reverse Forward Reverse with Brake Manual Factory Power profile setting will be supported 1 Factory Power profile it includes 9 levels for modify race and 4 levels LCTS linear control timing system for race competition 11 Manual Power profile it can adjust the setting on the throttle power profile Use the pocket size program card to program the controller settings Multiple protection functions Low voltage cut off protection Overheat protection Throttle signal loss protection Extra smaller size aluminum casing for cooling Extra battery output adaptor connecting to the motor cooling fan only for XPS Pro and XPS Sport 3 Connection Diagram TEAM POWERS BATTERY IME sensor B SENSOR Receiver Installation Tips AAT OR oe Connect the speed control to the receiver positi2. Setting Card Picture YN TEAM POWERS Step 2 How to program the mode function setting Mode The value shown on the LED display represents the corresponding mode function Each mode description can be referred to the program mode function table page5 Value The value shown on the LED display represents the value setting in the corresponding mode function The setting range can be referred to program mode function table page5 Press the Mode key to select the mode setting O Press the Up and Down key to select the mode setting values After all values has been set press the Upload key to upload all new data to the speed control If factory default setting wants to be restored press and hold Up and Down key for 15 and all default factory settings value will be restored on setting card Please remember to press the Upload key to upload all default setting data to the speed control again 7 Suggested manual setting for Modify and Stock mode programs 6 5T 9 5T Standard Size Brushless Motor h s s 1 ps 10 5T 17 5T Standard Size Brushless Motor ho qp dp od de Reference gear ratio for combo with Team Powers motor by the default speed control setting EN TERMIT ROWERS No motor and servo functions Wiring problem Check wire and connectors Wrong polarity when connecting the Correct the polarity when connecting BEC wire to the receiver the BEC wire to the recei
3. first and repeat the Step 2 procedure In setup mode XPS will store all settings such as neutral forward or endpoint position inside the XPS memory and will not lose even if it is disconnected from the battery Notes If you find the Throttle or Brake is reversed please reverse it back to normal position in the transmitter and go to step 2 to setup the speed control again YE TEAM POWERS 5 Mode Programming Program mode function table Mode function name Description Default Setting 1 Power Profile 1 Manual Profile mode 8 16 will be set manually 4 2 5 Factory Stock Mode mode 8 16 are disabled 6 14 Factory Modify Mode mode 8 16 are disabled Higher value in Stock or Modify mode mean more overall power and aggressive in throttle response 2 Running Mode 1 Forward with brake 2 Forward Reverse pee E Sa a 3 Low voltage protection 1 No protection 2 2 7V cell 3 3V cell 4 3 2V cell 5 3 4V cell 6 45 of battery voltage 7 6090 of battery voltage 8 70 of battery voltage 1 4 higher value have higher reverse force PM 5 Max brake force 1 11 higher value have higher brake force um 6 Drag brake force 1 No drag brake 2 11 higher value have higher drag brake force 7 Over heat protection 1 No protection 2 100 C 8 Initial Punch level 1 9 higher value have higher initial punch 9 Advance Punch level 1 9 higher value have advanced whole power brand 4 10 PWM Frequency 1 8 8 PWM Profile
4. modes The profile details can be referred to the below PWM table II Sensor Timing Phase 1 0 45 0 45 Adjustment 1 step The below functions are for XPS Pro only 13 RPM Phase 2 2 51 RPM range 1000rpm step ser Te 0 30 Ad gp 0 20 0 25 delay 0 15 a Tro Acreraen Pa trier ve hendre 1 m YN TEAM POWERS PWM table Throttle Range wk e m m m m m dm mms moe A A mms m 2 The higher the frequency number the more aggressive for the throttle control WIN TEAM POWERS 6 Program Card Specifications Dimension 90mm L x 60 W x 10mm H Weight 35 Program Card Operation Step 1 Connection with Speed control OS witch off the power of the speed control and take out the speed control BEC wire from the receiver OConnect the speed control BEC wire to the connector of Program card Please make sure the speed control wire is connected properly based on the below description Connect BEC white color wire to the program card pin at S position Connect BEC red color wire to the program card pin at position Connect BEC black color wire to the program card pin position OConnect the battery to the speed control and turn on the unit After a while there should be a display that shows mode 1 setting value from the speed control and it 1s ready to set the speed control
5. arantee claim the inspection of the product and the repairs may be charged with a fee at the customers expense according to our price list A proof of purchase including date of purchase needs to be included Otherwise no warranty 10 TEAM POWERS can be granted For quick repair and return service please add your address and detailed description of the malfunction If Team Powers are unable to service those defective products that are no longer exist in the market we shall provide you with a product that has at least the same value from one of the successor series The specifications like weight size and others should be seen as in this user guideline Due to ongoing technical improvements which are done in the interest of the product Team Powers does not take any responsibility for the accuracy of these specs Distributor Service O Package your product with sales receipt together with the detailed description of malfunction OSend parcel to your national Team Powers dealer distributor Distributor repairs or exchanges the product OShipment back to your usually by COD cash on delivery but this is subject to the general policy of your national Team Powers dealer distributor If any further information need upon reviewing the instruction please feel free to contact enquiry rc explorer com For more about Team Powers product information please go to the below web sites http www rc explorer com or http
6. ntrol is not connected to the battery ORemove the motor gear to allow the wheels of the model are free to rotate Switch the transmitter on and set the transmitter throttle stick to the full brake position OConnect the battery to speed control and turn on the unit After the unit is on and wait for around 2 second there is a two beep tone will be generated from the motor It means the speed control enters to the throttle range setting mode and the full brake position has been set at the same time OAfter entering to the throttle range setting mode please move the throttle stick to the neutral position After that another two beep tone will be heard and the neutral position has been set TEAM POWERS tep 2 cont OMove the throttle stick to the full throttle position After that another two beep tone will be heard and the full throttle position has been set Move the throttle stick to the neutral position again and a music tone will be heard that means throttle range setting has been completed Step 3 Double check the speed control function The speed control can be checked based on the below LED status Functions Status LED Color Of the above LED status is correct corresponding to the speed control function then the setup procedure has been completed and the XPS 15 ready to use OIf you make a mistake during the setup procedure Please turn off the unit
7. on channel 2 Connect blue power wire to motor solder tabs Connect yellow power wire to motor solder tabs Connect orange power wire to motor C solder tabs Connect the hall sensor cable between the speed control underneath the solder taps and motor Connect red power wire to battery Plus Connect black power wire to battery Minus Point to notes ie All power wires should be connected properly according to the color indicator and avoid creating solder bridges on the solder tab Avoid soldering longer than 5sec per soldering joint when replacing the power wires on the speed control When connecting the battery to the speed control please make sure the battery or should be connected properly Please make sure to follow the above tips and notes to install the speed control otherwise the speed control may be destroyed due to the improper connection of the wires TEAM POWERS 4 Speed Control Setup Step1 Transmitter Settings Before setup the speed control please setup the following functions on your transmitter 1f available Servo Reverse Throttle Reverse Any setting keep unchanged after the set up procedure If the transmitter does not have any of the above function it is already in basic setup function Step 2 Set neutral forward and brake endpoint data to the speed control OS witch off the power of the speed control and please make sure the speed co
8. ver Transmitter Receiver or Battery Replace the components one by one defective Speed control defective Send for repair No motor function but servo is Wiring problem Check wire and connectors working Sensor wiring defective missing Change other wire Motor defective Change other motor Speed control defective Send for repair While accelerating motor stutters Sensor wiring defective Replace the wire Motor or Sensor board defective Change other motor or sensor board Power Capacitor failure Replace the power capacitor Radio interference Change the components location Speed control defective Send for repair Motor runs at constant slow speed Transmitter settings changed after Repeat set up procedure and never stops Humidity water in speed control Dry the speed control Radio Interference Transmitter batteries empty Replace transmitter batteries Bad battery connection Check wire connection Receiver transmitter or servo Replace the components one by one defective Receiver or antenna too close to Change the components location power wires of motor and battery mm TERMIT ROWERS 9 Warning Notes Please read the following instructions carefully before starting to use the unit For those users that do not have experience to use it please seek help from the professional users Please make sure the voltage applied to the unit is in the operating range and the battery and sign should be connected properly to the po
9. wer cord of the unit If battery is reversed to connect to the unit the unit will be burnt out Incase there is an abnormal operation in the unit please turn off the unit and go to section 4 to setup the speed control again 10 45 days Warranty Services All products are manufactured according to the highest quality standards Team Powers guarantees this product to be free from defects in materials or workmanship for 45 days from the original date of purchase verified by sales receipt This limited warranty doesn t cover incorrect installation operations that are instructed to users damaged by crash or any natural disaster This also applies the below things on Cut off the original power plug Receiver wire and or switch wire damaged OMechanical damage of the case OMechanical damage of electronic components PCB Humidity Water inside the speed control C Soldered on the PCB except on solder pads OConnected speed control with reversed polarity Before you send in this product for repair please try to eliminate all other possibilities or improper handling by checking all other components in your model and the trouble shooting guide If the products are sent in for repair which do operate perfectly we have to charge a service fee according to our pricelist With sending in this product the customer has to advise Team Powers if the product should be repaired in either case If there is neither a warranty nor gu
10. www team powers com 11
Download Pdf Manuals
Related Search