PDF: 2.9 MB
Contents
1. that carve grooves into the plastic as they are inserted F AN C AUTI O N Please be sure to read the following instructions before assembling this kit Take necessary caution when handling parts with pointed edges There is a risk of injury This kit includes screws and other small parts Be careful not to swallow them There is a risk of suffocation Two AA batteries are used Incorrect use of the batteries may cause the generation self threading For this reason the screw hole may of heat explosions or liquid leakage The following precautions should be taken Do not use rechargeable batteries such as NiCd batteries or Oxyride batteries Ensure that the positive and negative terminals of the batteries are aligned correctly if liquid that leaked from batteries gets into your eyes rinse it well with plenty of water and consult a doctor immediately If liquid leaks onto your skin or clothes immediately wash it off Always remove the batteries after use Do not mix old and new batteries be damaged if you exert too much force when tightening the screw Since it is difficulty to turn a Full scale image of precision screwdriver please use a small driver that screwdriver has a grip radius of about 2 cm Materials used in this kit Body black neck white GPPS Tuning shaft bridges black POM Store the kit in a location out of the reach of small children Please read the instructions a2. 2 mm of the head protruding 2 Attach the tuning peg knobs Temporarily Attach the tuning peg nuts to the tuning peg knobs Then attach them to the insert the tuning shafts by turning the knob washer head screws Neem Make adjustments so Tuning peg nut that the wings of the Ts knob are the same height as the tunin Tuning peg Par g Wings of the knob Tuning shaft Attach the strings 3 3 Secure the string anchor shaft Insert the string anchor shaft into the groove in the neck Pass the bolt over the strings while holding the strings and string anchor shaft Secure it with a bolt and nut 2 Slide the strings onto the string anchor shaft Unwind the strings leaving the piece of paper bundling them Once you have unwound the strings remove the paper Slide the rings on the tips of the strings onto the shaft to attach the strings in order of thickness String anchor shaft Note the direction in which it is attached N Remove the paper bundling the strings soon after unwinding the strings Strings ON Separate the strings so that there are two on each side of the protrusion String anchor Pa shaft Thick 4 Attach the strings 1 Pass the strings through the holes on the tuning shafts to the front of the body 2 Along the protrusions 3 pass the strings through the groove at the top of the neck and pull 4 Then wrap the strings clockwise one and a half times around the washer hea
3. or the like Following this ensure that the strands are well wrapped around each other Q The guitar does not produce any sound when turned on A Confirm that the batteries are new and that they have been inserted in the correct direction A Ensure that the pickup and battery connectors have been securely fastened in place Q Increasing the volume has little effect A Ensure that the speaker is facing the correct direction The transparent cone should be facing outward A Indentation of the transparent speaker cone can also cause the volume to stay low Otona no Kagaku Q Turning the tuning peg does not cause the pitch to rise A The initial string tension may be insufficient Remove the neck cover loosen the washer head screw securing the string in question increase the tension in the string and then retighten the screw A Note that excessive tightening of the tuning peg can damage the threads on the tuning shaft If this has occurred remove the string in question move the peg lug to a position beyond the damaged threads and then tighten the string Q The guitar cannot be tuned properly A Check whether the bridge has become detached or is angled incorrectly
4. How to assemble the supplement Built in Amp and Speaker Mini Electric Guitar Parts in the Kit i ii Coil wire Strap ring Pickup bottom Sticker plate Lead wires n Circuit board l x ack Speaker Ba E When shipped the speaker is protected by Neck cardboard The neck cover might have been set to the neck Bolts Nuts Tuning peg String anchor shaft when shipped Please remove the neck cover before 2 each ts 4 assembly ee Neck cover Pickup top plate Magnet When shipped the pickup top plate and the EA A P magnet are set to the body Please remove them ff S before assembly Bridges 4 Tuning shafts 4 Pick AY Strings 4 Tuning peg knobs 4 volumedial Washer head Screw large Screw Screw small screw medium Things you will need Left over screws are spares Screwdriver cellophane tape rubber bands scissors two new AA alkaline batteries or two zinc carbon batteries NiCd and other rechargeable batteries have low voltage Therefore the guitar may not work when these batteries are used Oxyride batteries have high voltage Using these batteries may break the circuit Notes for tightening screws When tightening screws firmly press the screwdriver straight against the screw and turn It is said that 70 percent of the force applied is used for pushing against the screw and 30 percent for turning it The types of screws used for the supplement are those
5. ached together evenly If the neck is not straight loosen the two bolts straighten the neck and retighten the bolts Finished 7 Let s make some noise Insert the batteries and turn the power on Insert the batteries into the battery box and turn the volume dial to ON The power lamp lights when the power is on You can adjust the volume with the volume dial Volume dial Power lamp Let s tune If you have a musical instrument nearby tune the guitar using the scales of the instrument Turn the pegs to adjust the tension of the strings until getting the desired pitch When you turn the pegs you are increasing the tension in the strings from loose to tense The pitch will gradually increase while you are turning the pegs Stop turning when you have reached the desired pitch If you have tuned too high turn the pegs to reduce the tension in the strings and start tuning again Because the tension in a string changes during tuning it may affect the other strings Since the tuning of one string will affect that of the others and may change their pitch once you have finished tuning all four strings start again from the thickest string For lowe 12 For higher The pitch of each string is as shown to the left Pitches that are connected with arrows are the same pitch Therefore if you tune one string you can use that string to tune the other strings as well If you do not have any musical in
6. d screws that were temporarily inserted in step 1 and secure the strings with the washer head screws NGuue es Approximately 5 to 6 cm of excess string may be left and the rest can be cut off using tools such as a wire cutter Take caution not to cause any injuries with the excess strings Strings should lie in the groove guides P Wrap the string clockwise around the washer head screw Attach the strings so that they are parallel to the neck and adjust them so that the width of spaces between the strings is even String should be in the A o Width of spaces is even Protrusion Parallel Parallel When seen from the front each string should lie against the protrusions as shown in the figure Repeat steps 1 to 4 and attach all strings Otona no Kagaku 5 Attach the bridges Attach the bridges and lay the strings in the grooves in the center of the bridges Turn the pegs and adjust the string tension so that they are relatively tight be careful not to overtighten the strings If it is difficult to attach the bridge because the strings are too tight loosen the strings slightly Face the raised side of the bridge towards the neck and place it on the closest position to the neck Assemble the electrical components 1 Attach the volume dial Align the volume dial hole and place the volume dial onto the volume dial protrusion on the circuit board and fast
7. en it to the circuit board with the screw small Screw small T Volume dial 2 Attach the speaker to the body cover Secure the speaker with washer head screws EANA The speaker may become tilted if the screw is overtightened Do not secure the speaker while it is tilted If this happens loosen the washer head screw half a turn Washer Speaker head screws It becomes easier to secure the speaker if the washer head screws have been The side with passed through the screw holes on the the transparent rubber part of the speaker beforehand cone should face up Try not to touch the cone Body cover 3 Attach the jack Remove the nut and washer attached to the jack Then pass the jack through the hole for the jack in the body cover and secure it with the nut and washer removed Jack Washer Body cover Store the green and purple lead wires close to the speaker 4 Connect the power connector Plug in the power connector to the circuit board Plug it in firmly Red Note the direction of the connector 5 Mount the circuit board Adjust the position of the circuit board so that the volume dial and the power lamp protrude from the holes in the side of the body cover Secure the circuit board with the screws medium Screws ee medium g Circuit board Body cover Store the black lead wire of the jack in the space to the right of the jack as shown below a and the green and purple lead wires
8. her head screws Pickup Lead wires of the pickup g Washer head screw SAVUN Pass the lead wires of the pickup to the back from between the body and the endmost string 9 Connect the lead wires and earth wire Connect the lead wires that have been passed through to the back to the connector for the lead wires on the circuit board In addition after slightly loosening the screw a on the back of the neck which fastens the second thinnest string attach the earth wire on the circuit board to the screw a and re tighten the screw a a Lead wires 1 0 Attach the neck cover Attach the neck cover to the neck and secure it with washer head screws in three locations Washer head screws Neck cover 2 Be careful not to pinch the strings when tightening the screws 11 Mount the body cover onto the body Mount the body cover onto the body and secure it with the screws large Screws large Ea Retighten the bolts and nuts Earth wire Lead wires FAVO Ensure that the lead wires of the pickup do not come off 12 Attach the strap ring Attach the strap ring to the position shown below and secure it with the washer head screws Ad Washer head screws Strap ring If the strap ring cannot be slid around try again after loosening the screws securing the neck to the body EONA After attaching the strap ring observe the guitar from the side to make sure that the neck and body are att
9. in the space between the jack and the speaker b Make sure that the black earth wire c as well as the red and black lead wires of the circuit board extend out from the top side of the circuit board If it is difficult to turn the volume dial the lead wires may be in contact with it Properly store the lead wires again 5 Assemble the pickup Combine the top and bottom plates of the pickup Press the top and bottom plates of the pickup together until they click into place Pickup bottom plate Pickup top plate 2 Pass the coil wire through the hole in the pickup bottom plate Pass the coil wire through the pickup bottom plate At this point pull about 5 cm of the coil wire through and affix it with cellophane tape Pull about 5 cm of the coil wire through 3 Wind the coil wire Wind the entire length of the coil wire around the pickup SAONE Try not to leave any slack in the coil wire when winding it Be careful as pulling the coil wire too tight will break it The coil wire can be wound around in either direction Screw large Temporarily attach the pickup to the body using the screw large and wind the coil wire Remove the pickup when finished Grip the neck and wind the coil wire around the pickup Use the hand holding the coil wire to straighten the wire while winding 4 Bundle the coil wire Pass the end of the coil wire through the hole in the pickup bottom plate and
10. nd cautions thoroughly before use For your safety be sure to follow the instructions and cautions in this manual In addition do not use any parts that have become damaged or deformed during use Otona no Kagaku Body cover neck cover pickup tuning peg knobs volume dial strap ring pick black ABS resin Strings Stee String end pins Brass Screws bolts nuts black Iron Battery contacts string anchor shaft Iron nickel plated Coil wire Copper polyurethane leads Please dispose of this product in accordance with local regulations Assembled Product and Part Names Strap ring Strings Battery box Power lamp Assembling the Body Assemble the tuning unit Attach the neck Turn the neck and body over and attach the body to the neck from above Fasten Attach the tuning shafts to the body y y Face the side with the square protrusion up and insert the tuning shafts firmly from the outside the neck side a only with a bolt and nut At this point there is no need to tighten the bolt and nut firmly CZ If the tuning shaft cannot be inserted properly try pressing the shaft in while rocking it left and right Although it may protrude slightly from Protrusion the body this is not a problem Tuning shafts 7 to 10mm Make sure that 7 to 10 mm of the tuning shaft sticking out Temporarily insert the washer head screws into the back of the neck Leave about
11. struments nearby the pitch for the dial tone when you pick up the phone is G You may find it useful to tune the 3rd string with this pitch Let s adjust each part After you have actually made some sound try changing the spacing between the strings or the position of the pickup You may find a difference in ease of play and in the sound Try moving them around until you find positions that you like Loosen the screws securing the pickup before adjusting the position of the pickup Cp 0 gt How to change strings Change a string if it has broken or become worn Use strings for electric guitars We recommend the string gauges to the right To change the string 1 turn the pegs so that there is no tension remaining in any of the strings 2 Remove the strap ring neck cover and body cover 3 Remove the washer head screw on the back of the neck that is securing the string to be changed 4 Remove the bolt securing the string anchor shaft 5 Pull and lift up the string anchor shaft and remove the string from the shaft 6 Pass the new string through the shaft and retighten the string String gauges inch 1st String 009 to 010 2nd String 011 to 013 3rd String 016 to 017 Ath String 024 to 026 Q The coil wire has broken A Join the two broken ends and continue winding The coil wire has a transparent coating and this should be removed using sandpaper
12. through the other hole a remove the cellophane tape and pass the other end of the coil wire through the first hole b Se Otona no Kagaku 5 Bundle the coil and lead wires Nee Do not cut off the silver parts on each of the coil wire Doing so will cause current to stop flowing through the wire and the speaker to stop producing sound Bundle each end of the coil wire and lead wires by twisting them together Fasten one end of both the coil and lead wires with cellophane tape twist them together and then bundle them again with cellophane tape Either the red or black lead wires can be bundled Twist the lead wires together beforehand as shown below Lead wires Cellophane tape Wind the coil wire and lead wires that have been bundled together with cellophane tape around the pickup Excess coil wire should be folded and wound around the pickup O 2A 0 ed gt Sites l Do not wind this part around the pickup 6 Cover the coil wire and lead wires Cover the coil wire and lead wires with rubber bands or a thinly cut piece of cellophane tape Cellophane tape or craft tape 3 to 5 mm width Rubber band 7 Insert the magnet into the pickup top plate Insert the magnet into the top plate of the pickup and affix the provided sticker on top Sticker 8 Install the pickup to the body Insert the pickup in from the side below the strings and attach it to the body from behind using the was
Download Pdf Manuals
Related Search