IS200-MH User Manual
Contents
1. 1 32m 4 33ft 1 98m 6 50ft 7 Menu Operations wos o Auto Run Internal Master Alone Program1 8 Music Control Internal Master Alone Program1 8 i oo Mic sensitivity 0 99 Sensitivity of mic Edit Program Program Steps 1 48 Programs Scenes 01 Pan XXX Set each scenes aie value and time Scenes XX Time xx xS Mode of channel Mode Set 16Bit Mode 8Bit Mode Design Mode Design Mode Set Max Channel XX 000 Prohibited PAN 001 channel PAN TILT Color Wheel Gobo Wheel 1 Gobo Wheel 2 Focus Prism ST a2. of Tilt movement GOE ESENES of ESES EME 194 255 Backwards rainbow effect from slow to fast Gobo 1 periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The IS200 MH provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastene Regardless of the rigging option you choose for your IS200 MH always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a car
3. s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies lt is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the fixt
4. high speed electronic strobe LED shutter with variable speed 16 DMX channels Other DMX modes available DMX512 master slave and sound activated controllable or auto operation 8 built in programs 064 095 Strobe effect slow to fast 128 159 Pulse effect in sequences Shutter 192 223 Random strobe effect slow to fast a 0 255 0 100 Linear dimmer Focus 0255 255 In near to out far Prism Frost me N 0 063 063 Prism rotation Prism rotation stop Rotating 064 127 Forwards rotation from fast to slow 10 Prism 128 191 Prism rotation stop 192 255 255 Backwards rotation from slow to fast 0 191 Max diameter to Min diameter Iris 7 Special m e Sg m m 2 Safety Instructions l CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Ze Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device L
5. 10 Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 1 150W High brightness white LED unit Control Signal DMX512 master slave and sound activated or auto operation Control Channel 16 DMX Channels Power Consumption 220W Dimensions 278 D x 321 W x547 H mm Packing Dimensions 495 D x415 W x660 H mm Net Weight 13kg Gross Weight 16kg 11 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three mon
6. eave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is for beam effect for on site decoration purpose Don t turn on the fixture if it
7. ether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head one Signal Cable one Omega Clamp Two Power Cable one Safety Chain One User Manual one 220 239 Internal program 7 240 255 Internal program 8 9 Key Features High power 150W white LED unit with light output less than 750W fixture but higher than 575W 160 179 Internal program 4 180 199 Internal program 5 200 219 Internal program 6 1147FC 12350LUX 2 5m 277FC 2985LUX 5m 123FC 1322LUX 7 5m 50 000 hours lifespan and low power consumption 16 bit smooth and precise resolution for PAN TILT movement 540 630 pan and 270 tilt movement Scan position memory auto reposition after unexpected movement 1 color wheel with 7 dichroic colors plus open Variable direction rainbow effect with speed adjustable 1 rotatable gobo wheel with 7 rotatable interchangeable and indexable gobos plus open 2 metal gobos and 5 glass gobos with speed adjustable stream effect dithering effect and rotatable clockwise or anticlockwise Gobo indexing function 1 static gobo wheel with 9 gobos plus open 1 prism wheel with 3 facet prism 5 facet prism and front filter plus open with speed adjustable and variable direction 2 meter to infinite electric focus 15 projection beam angle Improved optics and flat beam field Electronic linear IRIS 0 100 linear dimmer with 1 18 times sec
8. rying handle 5 DMX 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator N o gt CONTROLLER DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON 1 Ground DMX512 OUT me DMX512 IN 2 Data 3 Data 3 PIN XLR Om 3 PIN XLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 120 A j 6 Photometric Data Photometric Beam Angle Data 15 Beam Angle LUX x 0 0929 FC 1147FC 12350 LUX 277FC 2985 LUX 123FC 1322 LUX 15 Beam Angle Oft 2 5m 5m 7 5m 8 2 ft 16 ft 25 ft Beam Diameter 15 Beam Angle 0 66m 2 17ft
9. th make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer CE IS200 MH User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing Dialighting s IS200 MH For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Dialighting s IS200 MH is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos IS200 MH adopts powerful 150W pure white LED which features high brightness and stability Please carefully unpack it when you receive the fixture and check wh
10. ures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture from a ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and 200 219 Gobo 7 shake slow to fast 160 179 179 Gobo 5 shake slowto fast 5 shake slow to fast 180 199 Gobo 6 shake slow to fast 220 255 Rot gobo wheel cont rotation slow to fast 128 189 Forwards gobo rotation from fast to slow 194 255 Backwards gobo rotation from slow to fast 0 127 Gobo indexing Gobo 1 Gobo 2 0 031 Shutter closed 032 063 shutter open 8 DMX Channels Wodschanet Function Vos Desetplon o os ee Fine Fine control of Tilt movement
Download Pdf Manuals
Related Search