OptiD-100 - Andy`s Auto Sport
Contents
1. AA anzar OQpTiiUmiviA user s manual ian High Performance 7 Volt Line Driver 0 r D 1 Crossover Network w Remote Bass D U Boost Level and Q Controls INTRODUCTION Congratulations on your purchase of a new Lanzar Opti signal processor Opti mobile electronics are some of the most advanced car audio products available These quality audio products are designed and engineered to afford you years of uncompromising musical service Lanzar has utilized the latest electronic technologies in order to deliver a superb listening experience The D 100 Active Line Driver offers the listener the ability to enjoy the finest in mobile audio The D 100 unleashes the effortless natural and open quality of the real performance Car audio systems which utilize passive crossovers feed the music through chokes and capacitors which creates a bottleneck through which the music must pass Portions of the program material may pass through at different speeds creating distortion some of the music doesn t make it through at all With the Lanzar Opti D 100 you ll hear all the dynamics in the bass and still hear delicacies like fingers sliding across guitar strings general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting a Co general 18411188 Blue light illuminated control panel Rotary control2. Output levels NOT set correctly volume level e Check for shorts on the speaker leads 2 Awhining sound can be heard through the Check the red power wire It muse be speakers when the audio system is at low connected directly to the battery volume with the engine running The whining Check the system s ground point It muse noise remains unchanged or seems to make good contact with chassis ground disappear when the volume level is bare metal increased e The radio and the Line Driver must be grounded at the same reference point 3 There is a motor boating type of sound e Check the red power wire It must be when the engine is running and the audio connected directly to the battery system volume is set at a reasonably high Check the system s ground point It must level make good contact with chassis ground bare metal 4 High squeal noise from speakers e This is almost always caused by a poorly grounded RCA patch cord Limited Warranty policy All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment Units purchased in the USA are warranted to be free of defects in material and workmanship for three 3 years from the date of purchase This warranty is limited to the original retail purchaser of the Signal Processor Should the unit fail due to a factory defect in material or workmanship your unit will be repaired or replaced at the sole discretion of Lanzar To obtain
3. bandwidth gentle frequency from 40Hz to 400Hz n control put sensitivity of line out to match the input of additional Turning this control to adjust the in put sensitivity of the set to match the radio s output Allows you to control the phase of your subwoofer between 0 degrees and 180 degrees to help compensate for timing difference between drivers Allows you to control the subwoofer output between stereo and mono thus facilitating single subwoofer installation To be connected to the outputs of the source unit or signal processor To input additional amplifiers crossover or Audio system To be connected to the amplifier left right inputs Plug the modular telephone style cord connected to the remote control unit into this jack Use these connectors to deliver power ground and remote turn on control to the unit Frequency Adjustable Bass Boost Adjustable Q Control Power Supply Input Impedance S N ratio Max Output Signal Level Dimensions WxDxH inches Channel Separation Distortion millimeters REMOTE CONTROL UNIT 1 0 T Q 2 BASS FREQUE sets the center frequency of the bass boost effect from 40Hz to 400Hz T 3 BASS LEVEL his control sets the subwoofer level control T SELECT CY his contro 40Hz 400Hz 0 18dB 2 20 10 16V DC negative ground 10K Ohm more than 8548 7 0V RMS 60dB less than 0 0596 6x10 11 16x1 3 4 150 x 272 x 45 his
4. control will narrow or widen the boost frequency bandwidth Q factor being sent to the amplifier for each band from Q 20 Narrow bandwidth steep slope to 2 Wide bandwidth gentle slopes System wiring HIGH PERFORMANCE LINE DRIVER re R L R L pai reste 1 MNO MAX st rust e OptiD 100 SUBWOOFER ECEEIEEEUTM battery 12V Mounting and installation Your new Opti Series Line Driver comes complete with a required mounting hardware Mark the location for the mounting screw holes by positioning the Line Driver where you wish to install it and use a scribe or one of the mounting screws inserted in each mounting surface If the mounting surface is carpeted measure the pen Before attempting to drill the mounting holes take note of any wires of the mounting holes to mark the hole centers and mark with a felt tip ines or other devices in your vehicle which may be located behind the mounting surface Then drill pilot in the mounting surface for the mounting screws and insert then Tighten the screws securely Installation e A red 18 gauge stranded or heavier and insulated wire should be co nnected to the terminal marked 12V Wire an in line fuse holder on this lead as it is the 12 Volts DC wire for the system This wire should be connected to your veh
5. eck the entire audio system for noise before permanently securing the Line Driver mounting 1 Start the engine 2 Turn the audio system on 3 Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise If so turn both the audio system and the engine off Do not secure the Line Driver mounting screws Refer to the Trouble S Guide at this manual 4 f the audio system does not have any noise securely tighten the Line Driver mounting screw and double check the wiring cables for safe placement SYSTEM ADJUSTMENT Preliminary Adjustments Pre setting the system provides a necessary starting point for fine tuning the entire audio system to maximum performance NOTE DO NOT MOUNT Line Driver UNTIL THE FOLLOWING PROCEDURES HAVE BEEN COMPLETED 1 Preset each amplifier input gain adjustment at the amplifier to half of maximum 2 we ae up and listen carefully for obvious trouble in sound distortion no sound no hiss total silence Turn the system off refer to Trouble Shooting uide at this manual Caution DO NOT ROUTE AUDIO CABLES AND POWER CABLES TOGETHER THIS CAN CAUSE ENGINE NOISE IN YOUR AUDIO SYSTEM ALWAYS DISCONNECT THE SYSTEM FROM THE BATTERY BEFORE ATTEMPTING TO MAKE OR ALTER ANY CONNECTIONS THIS PRODUCT IS DESIRED FOR USE IN ANY 12 VOLTS NEGATIVE GROUND ELECTRICAL SYSTEM ONLY INSTALLING THIS PRODUCT IN ANY POSITIVE GROUND ELECTRICAL SYSTEM COULD SERIOUSLY DAMAGE THE AUDIO SYSTEM Adju
6. icle s battery If a wire is run directly to the battery make sure to install an in line fuse on this wire within 12 from the battery A black stranded wire of ground wire for the D 100 and should be attached to the same ground Keeping this ground wire as short as possible improves the electrical problems to a minimum An orange stranded wire of a least 20 gauge should be connected to the terminal marked Remote This wire connects to your head unit s remote out or power antenna lead out Th time the radio cd or cassette are playing This lead must also be conn System that utilize a remote turn on lead for powering up at least 18 gauge should be connected to the terminal marked Ground This is the B point with the amplifiers in the syste circuit and keeps ground related noise is wire should supply 12 Volts DC any ected to any other components in your e Connect all line inputs and outputs using high quality RCA RCA cables e Recheck all connections before powering up Set all level controls to their least sensitive positions and set all Line Driver controls switches etc to the desired frequency or position Once the system is powered up set the volume control on the head unit to about the 2 o clock position and then set all the amplifiers level controls for half output level TAPPING SCREW PTS 1 40 25 4 SPRING WASHER SW 4e B x4 Noise chech and SYSTEM adjustment NOISE CHECK Ch
7. knobs PWM power supply Variable line out level control Variable input level control Subwoofer variable phase shift control Subwoofer stereo mono mode control Remote bass boost level and Q controls Variable bass boost frequency 40 400 Hz Variable Q 2 20 Precautions To prevent short circuits be sure to disconnect the negative battery ground lead before wiring the system up When you finish the installation be sure to make one more check to be sure everything is done correctly Reinstate all car parts that were removed Reconnect the negative battery ground lead INPUT LINE OUT ourPuT features and specifications LINE OUT LEVEL INPUTJLEVEL PHASH SHIFT 12V OptiD 100 OptiD 100 1 PARAMETER Q SELECT 2 20 2 BASS BOOST FREQUENCY CONTROL 3 BASS BOOST LEVEL CONTROL 4 VARIABLE LINE OUTPUT LEVEL CONTROL 5 VARIABLE INPUT LEVEL CONTROL 6 VARIABLE SUBWOOFER PHASE SHIFT CONTROL 0 180 7 SUBWOOFER STEREO MONO MODE CONTROL 8 INPUT PORT 9 LINE OUT PORT 10 0UTPUT PORT 11 REMOTE CONTROL JACK 12 POWER TERMINALS features and specifications Adjustable Bass Boost Allows independent continuous change of the boost frequency bandwidth Q factor for each band from slope This control adjusts the bass boos This control sets the subwoofer gai Turning this control to adjust the ou amplifier crossover or audio system Q 20 Narrow bandwidth steep slope to Q 2 Wide
8. nd or reinstallation of the Signal Processor Lanzar s total liability will not exceed the purchase price of the Signal Processor Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts So the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state
9. sting The Line Driver The Line Driver provides variable enhancement of Line frequencies The level of peak boost varies from 0 to 41848 and the frequency at which peak boost occurs is adjustable from 40Hz to 400Hz 20 Q to 2 Q boost characteristic can be adjustable 2 Q characteristic boosts a wide range of frequencies and is useful for general sound quality enhancement The 20 Q characteristic boosts a narrow range of frequencies and can be used to tune a subwoofer system fo rmaximum output The Line Driver 0 adjustable should be set to the 2 Q wide position and the frequency control set approximately one octave below the subwoofer s resonant frequency In vented enclosures the roll off of the system is quite steep below the tuning frequency typically 24dB octave In this case the Line driver should be set for 20 Q narrow operation Never set the Line Driver boost frequency below a vented enclosuer s turning frequency For maximum output from a vented enclosure set the Line Driver boost frequency to the tuning frequency of the enclosure These adjustments can be made with the Line Driver in the signal path but make sure the effect is turned off remote level Min then verify operation of the Line Driver by increasing the boost level while listening for changes in subwoofer response Once operation of the Line Driver is confirmed adjustment can proceed TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE 1 There is an audible distortion at a low e
10. warranty service you must first call our Consumer Return Hotline number at 718 236 6948 to obtain a Return Authorization RA number This RA Number must appear on the outside of your package and on all paperwork relating to your return When returning the unit to us for warranty service it must be carefully packed and shipped prepaid to R A Lanzar Service Center 1600 63rd Street Brooklyn NY 11204 WWW lanzar com Line Driver You must also include the following items with your return e copy of your sales receipt or other proof of purchase e A brief letter indicating the problem you are experiencing with the product e nclude in your letter your return address daytime phone number and RA Number e Also include a check or money order for 20 00 for return shipping handling and insurance or provide your VISA MasterCard number with expiration date Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid This warranty will be considered void if the unit was tampered with improperly serviced or subject to misuse neglect or accidental damage All implied warranties of merchantability and fitness for a particular purpose are limited in duration to the length of the warranty Lanzar expressly disclaims any liability for incidental or consequential damages caused by product defects This warranty does not cover any expense incurred in the removal a
Download Pdf Manuals
Related Search