User`s manual - Starfelt Company AB
Contents
1. 120 mm 1 66 kg ABS Wall bracket WX302 OB Black WX302 OW White2. Outdoor Wall Speaker WX302 OB OW PROFESSIONAL AUDIO EQUIPMENT Outdoor Wall Speaker WX302 OB OW User Manual amp Installation Guide Warning e Only use the correct amplifier output voltage and impedance Exceeding these limits could cause fire or other failures Avoid explosions do not use the speaker around gasoline thinner or other combustibles e Only install the speaker in locations that can structurally support the weight of the speaker Not doing so may result in the speaker falling down e Do not use any other method than specified to mount the speaker If extreme force is applied to the speaker the speaker could fall down e Attach a safety wire to the speaker when it s mounted high above the ground Failure in doing so could cause the speaker to fall down for any reason e Avoid mounting the speaker in locations exposed to constant vibrations The mounting points can be damaged by excessive vibrations potentially causing the speaker to fall down Caution e Avoid electric shocks switch off the amplifier power when connecting the speaker e Avoid installing the speaker in locations exposed to solvents acids smoke and heaters as excessive exposute to these factors could result in speaker failure fire or electric shocks e Do not operate the speaker for an extended period of time at distorted sound This could cause irreparable damage to the speaker e Do not stand or sit on nor hang down from the speake
3. aterproof connector on the rear side of the loudspeaker On the cable part of the connector is a white dot displayed Depending of the position of the white dot the desired power can be selected The corresponding powers are shown on the sticker on the rear side of the loudspeaker The power impedance of the loudspeaker can be set in 3 adjustable steps of impedance for 100V 20 Watt 10 Watt 5 Watt and 1 step for 8 Ohm standard low impedance applications 1 8 Ohm 30 Watt 2 20 Watt 500 Ohm 3 10 Watt 1000 Ohm 4 5 Watt 2000 Ohm When the loudspeaker is connected to 70 7V facilities the power indicated in the table above will be reduced to half the power and when connected to 50V facilities the power will be reduced to a quarter When the desired power tap is selected the loudspeaker is ready to be used Additional information WX302 OB OW Technical specifications RMS Power Max Power Nominal Impedance Line transformer power tappings Sound pressure 1W 1m Sound pressure max W 1m 8 Ohm Sound pressure max W 1m 100V Frequency response 3 dB Frequency response 10 dB Cross over frequency Horizontal coverage Vertical coverage Drivers Dimensions W x H x D Weight Construction Accessories included Colour 60 W 30 W 8 Ohm 500 Ohm 20 W 1000 Ohm 10 W 2000 Ohm 5 W 85 dB 100 dB 95 dB 90 Hz 18 kHz 60 Hz 20 kHz 2500 Hz 100 100 1 HF 3 LF 199 x 129 x
4. r as this may cause failure of the speaker Installing the WX302 OB OW Mounting the loudspeaker The loudspeaker can be mounted both horizontally and vertically by means of the supplied mounting bracket For mounting the loudspeaker on the desired mounting location the mounting bracket should be removed from the loudspeaker This can be done by loosening the screws on either side of the loudspeaker After this is done the mounting holes should be indicated For a stable mounting of the loudspeaker it should always be fastened by two screws The position of the mounting holes depends of the mounting position horizontally or vertically with a spacing of 107 mm in between After this the bracket can be mounted on the desired location Always use the proper fasteners depending of the mounting surface Once the bracket is mounted on the desired location the loudspeaker can be fixed to the bracket Connecting the loudspeaker On the rear side of the WX302 OB OW is a special waterproof AWX 5 connector provided This allows to connect the loudspeaker to the amplifier output A special included connection cable should be used Always connect the white conductor of the connection cable to the COM output of the amplifier and the black connection terminal to the positive terminal of the amplifier output Mind the polarity markings when wiring the loudspeaker cables Power settings The power settings of the WX302 OB OW can be made by rotating the w
Download Pdf Manuals
Related Search