LVP602S LED Video Processor USER`S MANUAL
Contents
1. LVP602S LED Video Processor USER S MANUAL LVP602S User s Manual TABLE OF CONTENTS I Safety precautions II Connections of hardware 1 Rear view LED VIDEO PROCESSOR 11 12 15 15 17 18 LVP602S User s Manual I Safety Precautions Danger There is high voltage in the processor to prevent any unexpected hazard unless you are a maintenance please do not open the cover of the device Warning 1 This device shall not encounter water sprinkle or splash please do not place anything containing water on this device To prevent fire keep this device far from any fire source To keep good ventilation there shall be at least 20cm interval between frontal and rear panel of the device If this device gives out any strange noise smoke or smell please immediately unplug the power cord from receptacle and contact local dealer Please do not plug or unplug DVI signal cable before shutting off the device Caution 1 Please thoroughly read this manual before using this device and keep it well for future reference In the event of lighting or when you are not going to use the device for a long time please pull the power plug out of receptacle Nobody other than professional technicians can operate the device unless they have been appropriately trained or under guidance of technicians To prevent equipment damage or electric shock please don t fill in anything in the vent of the device2. 750 DVI Format SD HD EIA 861B lt 1920x1080P 60HZ PC VESA lt 1600x1200 60HZ HDMI Format SD HD EIA 861B lt 1920x1080P 60HZ HDCP PC VESA lt 1600x1200 60HZ DP Format SD HD EIA 861B lt 1920x1080P 60HZ PC VESA lt 1600x1200 60HZ YPbPr Format SD HD EIA 861B lt 1920x1080P 60HZ YPbPr Y 0 3V 0 7V p_p 750 Scope Impedance Pb 0 35V 0 35V p_p 750 Pr 0 35V 0 35V p_p 750 SDI Format SDI SMPTE 259M C 576i 50HZ 480i 60HZ HDSDI Format HDSDI SMPTE 292M 1080i 50HZ 60HZ SMPTE 274M 2968M 720P 60HZ Input Connectors VGA 15pin D_Sub Female DVI 24 1 DVI_D YPbPr BNCx3 Composite video BNC D P Display Port SDI HDSDI BNC Outputs Nums Type 1xVGA RGBHV 2xDVI VGA DVI Format 1024x768060Hz 75Hz LED VIDEO PROCESSOR LVP602S User s Manual 1280x1024 0960Hz 75Hz 1600x1200 60Hz 1920x1080p 50Hz 60Hz VGA Scope Impedance R G B 0 7 V p_p 750 Output Connectors VGA 15pin D_Sub female DVI OUT1 24 5 DVI DVI OUT2 24 1 DVI_D Others Control Panel Button Power 100 240VAC 60W 50 60Hz Operating Temp 5 40 C Humidity 15 85 Size 155 mm high x350mm wide x 485mm length Weight 5 6 Kg VI Notes to model LVP602S with SDI HDSDI input interface LVP602 without SDI HDSDI input interface So all instructions regarding SDI HDSDI in above don t apply to LVP602 LED VIDEO PROCESSOR
3. Do not place the device near any water source or anywhere damp Do not place the device near any radiator or anywhere under high temperature To prevent rupture or damage of power cords please handle and keep them properly Please immediately unplug power cord and have the device repaired when 1 Liquid splashes to the device 2 The device is dropped down or cabinet is damaged 3 Obvious malpractice is found or performance degrades LED VIDEO PROCESSOR LVP602S User s Manual ll Connections of hardware 1 Rear view da OB fece i diia tas L jo ben 000 5 Sai 66 gt MO gt Figure 1 2 Port description 1 Video Input LVP602S supports 8 channel signal input including Port name Description V1 V2 2 channel PAL NTSC composite video input DP DisplayPort 1 channel DisplayPort digital HD signal input YPbPr 1 channel SD HD component signal input VGA 1 channel computer analog signal input DVI 1 channel computer digital signal input HDMI 1 channel digital SD HD signal input SDI HDSDI IN 1 channel SDI input SD HD 2 Audio Input LVP602S supports 5 channel stereo audio switch Of which 3 channels are DisplayPort HDMI and SDI audio the other 2 channels are AD1 AD2 external input audio AD1 and AD2 can be mapped to the corresponding audio input of any input among all video inputs and will be switched synchronous to the selection of video input signals 3 Video
4. selected input signal the current input signal source that you selected e g HDMI will appear in the first line in LCD and the status of current input signal source will appear in the second line If there are no valid signal input No Input will appear in the screem and dark screen will be displayed on the LED screen if the signal is valid the input signal format e g 1080p_60Hz will appear in the screen 2 Select output brightness Button names Description BRT Decrease output image brightness of LVP602S the lowest brightness is 0 BRT Increase output image brightness of LVP602S LED VIDEO PROCESSOR LVP602S User s Manual the highest brightness is 64 LVP602S supports 32 levels Brightness 0 represents the lowest brightness 64 represents the highest brightness To ensure full gray level of output image normally the output brightness is set as 50 3 VGA input auto adjustment Auto When the current VGA input source of LVP602S is a valid signal press this button LVP602S will automatically adjust the sampling parameters of the VGA signals so as to make VGA picture clean and complete In general this operation is made only when new VGA signal source is to be connected in The time spent in auto adjust depends on the conditions of signal source but will be no longer than 1 minutes Sometimes user need repetitively do such adjustment till VGA picture looks clea
5. Height Height of input image unadjustable 11 Hori In Str Input horizontal start for this model 12 Vert_In_Str Input vertical start 5 Audio 13 Audio1 Confi Audio1 configurations Configurations 14 Audio2 Confi Audio2 configurations 6 16 Device_Init 17 Bias 18 Auto ADC 1 Enter Setup of LVP602S Press Setup for consecutive 8 times while in operation mode Password 8 Enter Setup will appear in LCD LVP602S will enter the No 1 setup item After LVP602S enters the setup mode the 7 buttons on frontal panel will have the functions as defined in table below Name Functions Step Select step value 2 or 10 LED VIDEO PROCESSOR LVP602S User s Manual 1 Move to last item y Move to next item Decrease value or select last value Increase value or select next value Enter Save the adjustment or selected values Setup Enter or exit setup mode After LVP602S enters setup mode the relevant setup information will be displayed in LCD as per the layout shown in the figure below Figure 3 As shown in above figure LCD consists of five sectors Sector Description 1 The No of current setup item 2 ask you whether to save the adjustment the adjustment already be saved and takes effect 3 Newly adjusted value 4 Step value 5 Name of current setup item 2 Select langua
6. Output Port name Description VGA OUT 1 channel analog RGBHV signal output it can be connected to a local display device and used as monitor it is strongly recommended to use this port when operating and setting LVP602S LED VIDEO PROCESSOR LVP602S User s Manual DVI OUT 1 2 same DVI digital graphic signal output it can DVI OUT 2 be connected with external LED transmission card or LED transmission box SDI HDSDI 1 channel digital video signal loop output OUT 4 Audio Output AUDIO OUT Corresponds to the selected video input signal output this channel audio input signals 5 Signals of other ports RS232 serial communication port LED VIDEO PROCESSOR LVP602S User s Manual lll Frontal panel operations 1 Diagram of frontal panel Figure 2 2 Button instructions operation mode 1 Select input video source Button names Description V1 V2 Select V1 V2 BNC port from which signal is input DP DisplayPort Select DP DisplayPort from which signal is input YPbPr Select component signal input VGA Select computer analog signa input DVI Select computer digital signal input HDMI Select HDMI digital signal input SDI Select SDI HDSDI digital video signal input Switch audio input while operating above buttons select the audio signal input from corresponding video input to output it through Audio OUT Notes when user has
7. ernal input as audio input signals to the video signals in this channe then press Enter to save the settings Note AD1 AD2 can t be mapped to the video input signals in the same channel 7 Exit setup Item 15 Exit setup Press to move to the last option exit setup press or LED VIDEO PROCESSOR LVP602S User s Manual gt to select YES press Enter to exit setup Press Setup while in any setup mode the system will directly skip to item 15 8 Factory settings The following are settings made in factory area improper settings or improper operations in this area may result in malfunction of the processor we recommend users to make these operate following the directions of technicians of manufacturers Item 16 Reset When the system skips to item 15 from item 14 press V1 for 5 times then press to move to item 16 Reset press or gt to select YES press Enter the processor will resume default settings which were made in factory and the system will remind you please shut off power on again please operate following the indications ltem 17 Bias In order to reduce the noise of screen LED large screen system usually removes low scale noise but this will results in loss of image information especially those dark pictures like night views LVP602S can maje corrections by adjust
8. ge gt Y No 1 Item Language 3 After entering setup mode LVP602S will enter the first setup item Language i 5 LVP602S supports Chinese and English display press or gt to select either of them then press Enter to save it and make it valid 3 Output image setup LVP602S outputs images from VGA OUT DVI OUT1 and DVI OUT2 there are 7 output formats as listed in the table below User can enter the No 6 setup item Out_Format to select one fo them LED VIDEO PROCESSOR LVP602S User s Manual Format 1024x768 60 1024x768 75 1280x1024 60 1280x1024 75 1600x1200 60 1920x1080 50 1920x1080 60 N O Or INI No 6 Item Out_Format Press lt or key to select 1 output format listed under this option then press Enter to save it If you select 1024x768 60 the output resolution of LVP602S will be 1024x768 the vertical refresh rate is 60Hz However the resolution of LED screen is not exactly 1024 x 768 pixels When the resolution of LED screen is less than 1024 X768 pixels we can set LVP602S to output the images exactly fitting the resolution of LED screen so that the LED could display a full frame of image See the schematic diagram below 0 0 Hor_Str Hor_Width Vert Str Vert Height LVP602S Out Format 1024 X 768 IY 1024 Figure 4 As above figure shows the size and locat
9. he color looks Press lt or to increase or decrease the values of color saturation Press Enter to save the settings Normally the value of color saturation is set as 50 LED VIDEO PROCESSOR LVP602S User s Manual 5 Input image setup Items 9 12 are the menus for multiple machine to work together in parallel they don t apply to LVP602S Items No Item Name 9 Input Width 10 Input Height 11 Hori In Str 12 Vert In Str 6 Audio configurations LVP602S supports 5 channel stereo audio switch Of which 3 channels are DisplayPort HDMI and SDI audio the other 2 channels are AD1 AD2 external input audio AD1 and AD2 can be mapped to the corresponding audio input of any input among all video inputs and will be switched synchronous to the selection of video input signals If HDMI or DP SDI is configured with external input audio when you switch it external input audio will be selected otherwise the aidio signals contained in HDMI or DP SDI will selected as input Item 13 AD1 audio configurations Press lt or to select 1 channel of video input signals from all input signals map AD1 external input as audio input signals to the video signals in this channe then press Enter to save the settings Item 14 AD2 audio configurations Press or to select 1 channel of video input signals from all input signals map AD2 ext
10. ing Bias the limit value ranges between 32 64 In the event signals of dark screen are missing increase this value the missing information will appear on large LED screen In order to ensure complete output gray the standard value is set to be 50 Item 18 Auto ADC The processor without calibrating white balance may suffer color cast or low brightness when it is connected with analog signals LVP602S can automatically adjust white balance based on the analog signals input including AV YPbPr and VGA to solve the above problems The procedures of Auto ADC are as below Shift to corresponding analog input signals when the processor detects input signals and output it to display enter the item 18 optiom of setup menu press lt or to select YES press Enter the processor will calibrate white balance Note as processor has calibrated white balance using standard LED VIDEO PROCESSOR LVP602S User s Manual signals in the factory please don t use the function of this option unless necessary LED VIDEO PROCESSOR LVP602S User s Manual V Specifications Inputs Numbs Type 2xcomposite video 1xDP Display Port 1xYPbPr 1xVGA RGBHV 1xDVI 1xHDMI 1xSDI HDSDI Video system PAL NTSC Composite Video Scope Impedance 1V p_p 750 VGA Format PC VESA lt 1600x1200 60HZ VGA Scope Impedance R G B 0 7 V p_p
11. ion of LVP602S output images are defined by 4 groups of parameters which correspond to four setup items respectively for details of their relationship see Table 5 below LED VIDEO PROCESSOR LVP602S User s Manual No of setup item Setup Item Name Names of parameters 2 Hori_Start Hor_Str 3 Hori Width Hor Width 4 Vert Start Vert Str 5 Vert Height Vert Height The start coordinates 0 0 of LVP602S output image is defined in the right top of 1024 X 768 pixels output area Set the four setup items as listed in above table as per the size of current LED screen pixels and start position of the input image that LED displays Press ft or to select setup item press or gt to increase or decrease the values of current item Press Enter to save the settings 4 Brightness Color No 7 setup item Brightness LVP602S supports 32 levels Brightness O represents the lowest brightness 64 represents the highest brightness Press lt or gt to increase or decrease the values of brightness Press Enter to save the settings To ensure full gray level of output image normally the output brightness is set as 50 No 8 Item Color For V1 V2 DP YPbPr and HDMI video input source LVP602S can set color saturation ranging between 32 64 The lower this value is the weaker the color looks the higher this value is the stronger t
12. n complete and stable 4 Information display Info Press this button to view current settings and information of LVP602S it consists of 17 items If you press Info again before LVP602S exit information display LVP602S will continue to display the next item of information 5 Select Full Part display Full Part This function only applies to PC input signals DVI VGA DP HDMI user can switch between them Other input signals can work only in the full mode Button names Description Full Full means that LED will display a full picture Part Part means that LED only display a part of a picture LED VIDEO PROCESSOR LVP602S User s Manual IV Setup The following setups must be made by relevant qualified technicians For ordinary users unless they have received adequate relevant training they shall not attempt the following setup operations There are 14 items in 5 categories available for you to set in LVP602S Technicians can set these items as necessary for details see the table below Category Items Description 1 Language 1 Language 5 Selection 2 Output Image 2 Hori Start Output horizontal start Setup 3 Hori_Width Output width 4 Vert_Start Output vertical start 5 Vert Height Output height 6 Out Format Output resolution 3 Brightness 7 Brightness Color 8 Color 4 Input Image 9 Input Width Width of input image Setup 10 Input
Download Pdf Manuals
Related Search