User Manual
Contents
1. data approximately 10 sec onds BE Remote V 44 please wait t gt 10s SELECTING THE CASSETTE BX a E Bx2 ENCODER DB BHII ee sence gt v5 HDR a_a e If necessary select the cassette to be programmed by repeatedly pressing the il button e g Box 2 gt The display shows e g the menu Bx 2 ENCODER Bx 2 stands for slot 2 ENCODER HD type of cassette y 51 software version of the cassette e Press the MOJ button gt The Encoder settings ENCODER main menu is activated ass 14 PADE 4001 css ENCODER Via this menu you get access to the submenus in order to do the encoder set tings and to select the desired input gt If no encoder settings should be done press button MANA The ASI output OUTPUT main menu is activated page 18 e Press button I gt The SERVICE ID submenu is activated Service ID SID In this menu you can assign a Service ID for the signal which is to be encoded Bx 2 SERVICE ID 00001 e Use the P E buttons to select the digit of the SID to be set and use A B buttons to set the desired SID gt Take care not to assign the same SID twice e Press the MA button gt The Programme name NAME submenu is activated PROGRAMME NAME In this menu a programme name for the sign2. Video signal type input ccnesseenennenssennnennnneneneneeennennn 16 Group of Picture GOP anne en 17 Audio input Audio level net 17 Audiodateien 18 ASO UB Ub sense 18 AS transfer rate sans 19 POP MONS eg serielle 19 ASI Input station Hiller ee 20 Gitputdata rate see 22 Transport stream ID and ORGNET ID u nen 23 Network Information Table NIT ee 23 Factory reset Soft reset cceccccceeeeceeeeeceeeeeeeeeeeseeeeseseeeeeeeees 24 Factory reset een 24 SON reset eero nee een 25 Saving settings 20 0 eee cece cece cc cec eee ee eee eeeeeeeeeeeeeeaeaeseeeeeeeeeeeeeeeeeeeeeess 25 6 Final procedures 26 css a2 2 PADE 4001 It E gt SAFETY REGULATIONS AND NOTES Assembly installation and servicing should be carried out by authorised electricians Switch off the operating voltage of the system before beginning with assem bly or service work or pull out the mains plug Do not perform installation and service work during thunderstorms Install the system so it will not be able to vibrate ina dustfree dry environment in such a manner that it is protected from moisture fumes splashing wa ter and dampness somewhere protected from direct sunlight not within the immediate vicinity of heat sources in an ambient temperature of O C to 50 C In case of the formation of condensation wait until the system is completely dried Ensure that the h
3. the audio signal shall be en coded Bx 2 AUDIO 192 kbps Stereo e Use the R E buttons to enter the desired audio data rate gt Some data rates are selectable for mono as well as stereo signals e Press the MA button gt Return to the main menu Encoder settings e Press the MA button gt The ASI output OUTPUT ASI main menu is activated ASI output Herein you get access to the submenus for ASI output settings gt If no ASI output settings should be done press button SNF The ASI Input station filter INPUT main menu is activated Bx 2 OUTPUT ASI e Press the J button gt The ASI transfer rate ASI RATE submenu is activated ass 18 PADE 4001 ASI TRANSFER RATE In this menu you set the transfer rate for the ASI component connected incl stuffing filled up user data rate For this setting please take the required information from the documentation technical data of the ASI component to be connected Bx 2 ASI RATE 108000 KBits e Use the B E buttons to select the digits to be set for the transfer rate then use the R E buttons to set the transfer rate wished e Press the MA button gt The ASI options ASI OPTION submenu is activated ASI options In this menu you define the size of the data packets their polarity and the type of transmission For this setting please take the required information from
4. the documentation technical data of the ASI component to be connected Bx 2 ASI OPTION 188 pos cont e Press the E I buttons to set the size of the data packets 188 or 204 bits e If the polarity of the data to be transmitted has to be changed press the El Eto select pos positive standard and using the R E buttons set to neg negative e To change the type of transmission press the BJ EJ buttons to select cont continuous standard and using the E E buttons set to burst gt Setting cont The data packets of the user data are spaced out evenly in the trans port stream a Q PADE 4001 gt Setting burst The data packets of the user data are collected to a great data packet in the transport stream e Press the MA button gt Return to the main menu ASI output e Press the MA button gt The ASI Input station filter INPUT main menu is activated ASI INPUT STATION FILTER Herein you get access to the submenus for ASI input filter settings gt f no ASI input filter settings should be done press button MAA The Output data rate DATARATE main menu is activated page 22 Bx 2 INPUT ASI OK gt gt If no ASI input signal is present is displayed instead of OK Bx 2 INPUT ASI gt e Press the button Bx 2 FILTER all Using buttons R E you can select whether all services all or only
5. English Grundig SAT Systems PR FESSIONAL Professional Analogue Digital HD Encoder PADE 4001 ce E KLASSE CLASS GSS Phone 49 0 911 703 8877 Grundig SAT Systems GmbH Fax 49 0 911 703 9210 Beuthener Strasse 43 E mail info gss de D 90471 Nuremberg Internet http www gss de en CONTENTS 1 Safety regulations and notes s sesessesesessesesessesesssesesscsesessesesessesesesessesese 3 2 General information s ssesesessesesesseseseseseesesesscsesessesseesesessesesessesesesseesseseses 4 2 1 Packing CO itis gerne 4 2 2 Meaning of the symbols used nn nae aioone 4 2 3 Technical dat une mie naher 4 2 A Des please 6 Sionalrinime ae een 6 Software versions nenne 7 Block AAFC ee 7 3 Assembly ANNE estere derne rens 8 3 1 Installing the Cassette asnndnsnasendeanateannnnsnnienereeneanseegneninranannaiaves 8 32 EMC Ballon 9 3 3 Cassette Overview ae sense DE Eur REEE 10 3 4 Connecting the cassette ccccccecccceeeeeceeeeeseeeeeeeeeeeneeeeenseeeeeeeees 10 4 The control panel at a glance scsscsssssssssseccssscsssseccessssscsacecsecsaseaseees 11 Al Mendes 11 412 Control pant nennen 11 5 Programming E E 12 5 1 Programming procedure unansse 12 3 2 Programming the cassette u ernennen 14 Selecting the cassette ns nerne treere reen erne rener 14 ENCOd ER ea 15 Service ID SID r nenne innen 15 Programme name een 15 Tot l data rater user 16
6. Flash You can find the current operating software on the website www gss de en SIGNAL RUNTIME Channel switching at a HD source becomes effective only after a time delay of up to 3 seconds because of the signal runtime SE PADE 4001 ss SOFTWARE VERSIONS Cassette After activating the cassette the software version of the cassette is displayed see page 14 Control unit To operate these cassettes the software version of the control unit must be V44 or higher Approximately 5 minutes after the last keypress the software version of the control unit is displayed If necessary you can activate the indication of the software version of the control unit manually e Press any two keys on the control unit of the head end station simultaneously until the display goes dark and the software version e g V 44 appears BLOCK DIAGRAM ASI Eingang ASI input BNC SPDIF HP TPS MODUL ASI Ausgang EES ASI output BNC ENCODER Y FBAS Y CVBS Pb alfa PADE 4001 INSTALLING THE CASSETTE 3 1 N Ensure the head end station is mounted so it will not be able to vibrate Avoid for example mounting the head end station onto a lift shaft or any other wall or floor construction that vibrates in a similar way Before installing or changing a cassette unplug the power cable from the mains power socket e Remove the fastening screws 1 of an unoccupied slot from the br
7. ON R E B E 188 pos cont 1204 i Ineg MODE Iburst Y i Bx 2 INPUT Bx 2 FILTER i u gt 8 8 i ASI OK gt all all i A manual 1 nur bei Einstellung manual i i MODE i Only with setting manual 1 1 Y 1 N I Services entfernen hinzuf gen 4 BX2 TV 01 04 Removing activating services i i Das Erste n chster Service Programm 4 1 i next service station i ER RESEN EE S EEE E EPES RENE EN A EOS EO EEE mone i Bx 2 DATARATE i 93 0 108 0 Mb i Bx 2 TS ONID i e j 0x0001 0100 B E i Bx 4A B NIT off gt Make J Make Page 12 on off auf Werkseinstellung zur cksetzen und Bx 4 FACTORY g Bx 4 FACTORY Im speichern Defaults gt STORE gt M reset to factory defaults and store ma Page 12 Bx 4 RESET a RESET gt M mm Page 12 Gss a 13 PADE 4001 5 2 PROGRAMMING THE CASSETTE gt Pressing the MODE button for longer than 2 seconds cancels the programming procedure This takes you back to the programme item Selecting the cassette from any menu Any entries that have not been saved are reset to the previous settings gt Entries in the menus can be saved by pressing the IM key You are taken back to the Selecting the cassette menu item gt The parameters and functions to be set are underlined Cursor e Switch on the head end station gt The display shows the software version e g V 44 gt The processor reads the cassettes
8. acket of the head end station e Insert the cassette in this slot and push it into the housing e Align the cassette and apply slight pressure to connect it to the connections of the board and the HF bus bar e Fasten the cassette with the screws 1 OO JC CS JE 6 OM Jel gt G Q G D css 8 PADE 4001 3 2 EMC REGULATIONS KLASSE nm To comply with the current EMC regulations it is necessary to connect the lines leading in and out of the head end station using cable terminals When mounting the cassette in a head end station which is installed in a 19 cabinet make sure the connections leading in and out for the 19 cabinet are made using cable terminals The attenuation of shielding of the connection lines for ASI and antenna must meet the requirements for Class A e Insert the required number of cable terminals in the openings provided in the head end station or in the 19 cabinet Tighten the nuts on the cable terminals until the teeth on the lock washer have penetrated the exterior coating and a good connection is made between the hous ing and cable terminals For PADE 4001 3 3 CASSETTE OVERVIEW D SUB socket RS 232 ASI output ASI input Status LED ASI input OPTICAL S PDIF PCM audio input TOSLINK Audio input R analogous Audio input L analogous Video input Y CVBS Video input Pb Video input Pr ODOCOWVOOOOHO The oper
9. al which is to be encoded can be set Bx 2 NAME HD e Use the Bj EJ buttons to select the digit of the channel name to be set and use R E buttons to set the desired character gt Press button UM to delete the complete name PADE 4001 e Press the MO button gt The Total data rate BITRATE submenu is activated TOTAL DATA RATE In this menu you set the total data rate video audio tables with which the input signal shall be encoded Bx 2 BITRATE 10 0 Mbps gt The higher the resolution of the input video signal the higher the data rate must be set 1920x1080i 6 3 Mbit s 24 Mbit s 1280x720p 4 3 Mbit s 24 Mbit s 720x576i 1 3 Mbit s 10 Mbit s 720x480i 2 3 Mbit s 10 Mbit s e Use the R E buttons to set the data rate of the video signal 1 0 30 0 Mbit sec If only audio signals are to be encoded set the data rate to Audio only In setting Off the encoder is switched off e Press the MA button gt The Video signal type input INPUT submenu is activated VIDEO SIGNAL TYPE INPUT In this menu you select whether you would like to feed in a Composite video signal YPbPr via the green blue red cinch sockets or a CVBS video signal CVBS via the green cinch socket Bx 2 VIDEO IN yPbPr e Use the E E buttons to select the desired type of video signal input e Press the MOA button gt The Group of Picture VIDEO GOP subm
10. and ON ID must be unique at the plant gt If the TS ONID was changed a new NIT must be generated o Press the DREI button gt The Network Information Table NIT menu is activated NETWORK INFORMATION TABLE NIT Bx 2 NIT off gt Make e Use the R E buttons to switch off or on the NIT e Press the EJ button to activate NIT Make gt All active cassettes which are able to output a NIT NIT cassettes must be set and ready for reception gt The NITs of all NIT cassettes are switched on gt The cassette fetches all the information output frequencies output data rates etc it needs from all the NIT cassettes in order to generate the NIT This process may take a few seconds Then the NIT is generated added and sent to all NIT cassettes The other NIT cassettes also add this new NIT The status of all NIT cassettes in the NIT menu changes to on The display shows read copy J23 PADE 4001 e To switch off the new NIT off press the J button N gt The NITs of the other NIT cassettes will stay switched on When the NIT of the cassette is switched on again on by pressing the HE button the previously generated NIT is added again If you have changed parameters in the meantime you must first select Make to generate a new up to date NIT e Press the MODE button gt The Factory reset FACTORY Defaults main menu is activated Fac
11. ating software of the cassette can be updated via the 9 pin D SUB socket RS 232 using a PC or notebook and the software BE Flash You can find the current operating software on the website www gss de en 3 4 CONNECTING THE CASSETTE e Dependent on the input signal connect the source device via cable terminals to the input sockets Y Pb Pr 8 9 A0 or CVBS 8 Audio R 6 Audio L 7 or OPTICAL 5 If necessary connect the ASI input 3 and the ASI output 2 to the periph eral devices e Connect the head end station to the mains css 10 PADE 4001 4 THE CONTROL PANEL AT A GLANCE 4 1 MENU ITEMS Program the cassette using the buttons on the control unit of the head end sta tion The two line display of the control unit then shows the menus Use the MAJA key to select the following main menu items Cassette Encoder ASI Output ASI Input Data rate TS ONID NIT Factory reset 4 2 CONTROL PANEL The key pad on the head end station is used to scroll through the menus LOAA scrolls forward through the menus EXTEN scrolls backward through the menus B G select parameters in the menus gt selects sub menus BE set values M saves all entries ass 11 PADE 4001 5 PROGRAMMING 5 1 PROGRAMMING PROCEDURE BE Remote V 44 please wait Bedienhinw
12. ead end station is adequately ventilated Do not cover the ventilation slots Beware of short circuits No liability is accepted for any damage caused by faulty connections or inappropriate handling Observe the relevant standards regulations and guidelines on the installa tion and operation of antenna systems The standards EN DINEN 50083 resp IEC EN DINEN60728 must be observed For further information please read the assembly instructions for the head end station used Test the software versions of the head end station and the cassette and update them if necessary The current software versions can be found at www gss de en Take action to prevent static discharge when working on the device Electronic devices should never be disposed of in the household rubbish In accordance with directive 2002 96 EC of the European Parliament and the European Council from January 27 2003 which addresses old electronic and electrical devices such devices must be disposed of at a designated collection facility At the end of its service life please take your device to one of these public collection facilities for proper disposal age PADE 4001 2 GENERAL INFORMATION 1 Cassette PADE 4001 1 BNC cable 1 Brief assembly instructions 1 Measuring log 2 2 MEANING OF THE SYMBOLS USED N Important note gt General note e Performing works 2 3 TECHNICAL DATA The devices meet the following EU directives 73 23 EWG 89 336 EWG The
13. eise EX bl ttert Men s vorw rts t gt 10s ED nl ttert Men s r ckw rts 7 E 0 w hlen die Eingabeposition gt w hlt Untermen Bx Teese EI E stellen Werte ein ee IM speichert alle Eingaben Ai zeigt die Eingabeposition mO Page 1 3 Operating Hints Y EO scrolls forward through the menu Bx 2 ENCODER moo scrolls backward through the menu I I E E select the enter position v5 HD 00 Jeees ee gt selects a submenu mO SE BEE JE set values and triggers actions Page 13 MODE M saves all entries EA gt 2 sec abbrechen cancel i shows the enter position ENCODER SERVICE ID B E gt H F MODE l schen delete i n a i E E Bx 2 BITRATE B G an 30 0 Mbps i 10 0 Mbps H Audio only i Bx 2 VIDEO IN VEDRI CVBS i yPbPr H Bx 2 VIDEO GOP IBBP i IPPP i IBBP S E isp Bx 2 AUDIO IN CINCH 0 dB E E CINCH l OPTICAL i Bx 2 AUDIO i 192 kbps Stereo B B HIVE PADE 4001 Y i Bx 2 OUTPUT Bx 2 ASI RATE E0 l e gt DA i ASI gt 108000 KBits i MODE Bx 2 ASI OPTI
14. enu is activated a 16 PADE 4001 Group oF Picture GoP The GoP describes the order of reference and difference pictures of the data stream This influences the compression Bx 2 VIDEO GOP IBBP e Use the R E buttons to select the desired Group of Picture GoP gt IBBP high compression HDTV at low data rate for normal pic ture contents at higher channel switching delay IBP medium compression HDTV at medium data rate for fast moving contents e g sport at medium channel switching delay IPPP minor compression HDTV at high data rate for fast conver sion at short channel switching delay e Press the MA button gt The Audio input Audio level AUDIO IN submenu is activated Aupio input Aupio LEVEL Herein you can select the audio input via which the corresponding sound signal shall be fed Bx 2 AUDIO IN CINCH 0 dB gt An analogous audio signal can be fed via the cinch sockets and a digital PCM audio signal can be fed via the Toslink socket optical S PDIF interface Audio input e Use the W M buttons to select the desired audio input Audio level e Press button I to get to the level setting e Use the R E buttons to enter the desired audio level 1 1dB 11dB 17 PADE 4001 e Press the MO button gt The Audio data rate AUDIO submenu is activated AUDIO DATA RATE In this menu you set the data rate with which
15. es which are marked by will be passed If the services at the ASI input are changed new services which are not marked by will be blocked gt Pressing the button all services can be passed through or blocked e Press the MAA button gt Return to the main menu ASI input station filter J2 PADE 4001 e Press the JN button gt The Output data rate DATARATE menu is activated OUTPUT DATA RATE Herein the current needed and the maximum data rate is displayed Bx 2 DATARATE 93 0 108 0 Mb gt The maximum data rate is dependent on the settings of the ASI data rate If the current needed data rate is higher than the maximum possible data rate a is indicated Bx 2 DATARATE 112 0 108 0 Mb gt The value 108 0Mb results from the ASI RATE setting In this case correct the corresponding settings e Press the MAA button gt The Transport stream ID and ORGNET ID TS ONID menu is acti vated ass 22 PADE 4001 JAN TRANSPORT STREAM ID AND ORGNET ID If the input signals are encoded to a separate transport stream if no transport stream with ORGNET ID is present at the ASI input a new ORGNET ID must be assigned to the transport stream Bx 2 TS ONID 0x0001 0100 e Use the BJ E buttons to select the digit of the hexadecimal number to be set and use the E I buttons to set the desired character gt The combination of TS
16. nch socket Audio Inputs S PDEPEM ee ee 1 TOSLINK Analogous Stereo 2uuuennnnennennnesnennnsnnneenennne nennen 2 Cinch sockets Alp ee 1 BNC socket 75 Q PON OUND Nk re are 1 BNC socket 75 Q Connection strip 10 pin as for supply voltages and control circuit RS 2932 socket nee ee serial update interface Remote maintenance Remotely controllable via PSW 1000 220 eneeenneeneenenn yes Remote update via BEllash nn ee yes and a corresponding management unit ma PADE 4001 2 4 DESCRIPTION The MPEG4 Encoder Cassette converts a HD or SD video and audio signal into a MPEG4 data stream transport stream and outputs it via the ASI inter face For the Video input it can be selected between YPbPr SD HD or CVBS SD All common HDTV formats up to a resolution of 1920 x 1080i 50 60Hz are supported The stereo audio signal of a YPbPr resp CVBS signal can be fed in via the cinch sockets analogous or the TOSLINK S PDIF interface PCM A status LED at the ASI input indicates whether a input signal is present green The MPEGA encoder generates a transport stream according to H 264 AVC Advanced Video Coding High Profile Level 4 0 standard The transport stream can be cascaded via ASI The cassette is designed for use in head end stations of the profi line The operating software of the cassette can be updated via the 9 pin D SUB socket RS 232 using a PC or notebook and the software BE
17. nections cable terminals and cover screws in order to maintain compliance with current EMC regulations securely e Securely tighten the cable bolted connections using an appropriate open ended spanner e Mount the front cover see assembly instructions of the head end station ass 26 PADE 4001 ss Declaration of CE conformity Konformit tserkl rung GSS Declaration of Conformity Ga 140 13 Der Hersteller Importeur GSS Grundig SAT Systems GmbH The manufacturer importer Anschrift Address Adresse Beuthener Stra e 43 D 90471 N rnberg Germany erkl rt hiermit eigenverantwortlich da das Produkt declare under their sole responsibility that the product oa Professional Analogue Digital HD Encoder Type Model Type GSS PADE 4001 Bestell Nr Order No GAP 5400 folgenden Normen entspricht is in accordance with the following specifications EN 50083 2 2012 EN 60065 2002 EN 50581 2012 EN 60065 A1 2006 EN 60065 A11 2008 EN 60065 A2 2010 EN 60065 A12 2011 Das Produkt erf llt somit die Forderungen folgender EG Richtlinien Therefore the product fulfils the demands of the following EC Directives 2006 95 EG Richtlinie betreffend elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen Directive relating to electrical equipment designed for use within certain voltage limits 2004 108 EG Richtlinie ber die elektromagnetische Vertr glichkei
18. product fulfils the guidelines and standards for CE labelling page 27 Unless otherwise noted all values are specified as typical Component Video Input halle Y 1 Vss Pb Pr 0 7 Von Input impedans seat 750 Tested Video Formats 1920x1080i50 1280x720p50 720x576p50 720x480p59 Supported standards sinne PAL CVBS Video Input Input level eine IV Input impedance en seen ee 750 Frequency range nennen nee 20 Hz 5 MHz Supported standards ssssssseeeeeeeerereeree nere nere nerne retn rrrnee PAL BG Audio Input ptt IS V2 lis ee 500 mV ims Frequency range sra merenna a ne E E AEE E 20 Hz 15 kHz oss 4 PADE 4001 MPEGA Encoder Transport Stream nee H 264 AVC High Profile Level 4 0 Setting range of total data rate video audio tables 1 Mbit s 30 Mbit s Video data rate 192 OBO een 6 Mbit s 24 Mbit s 1280x720 0 ee 4 Mbit s 24 Mbit s 720X97 OL Siamese Aloe ER Er ER SICHERE RAFREREEEREEERUNER 1 Mbit s 10 Mbit s FZ OAD Ol nenne 2 Mbit s 10 Mbit s Audio dala Tale are a aeaa EE 32 kb s 384 kb s ASI Interfaces NOT ee e EE DIN EN 50083 9 FOr ee MPEG ISO IEC 13818 1 NEE Eo lol a HO SE TEATER E ETENE EE ET EA 108 Mbit s Impedance eiieeii a eE ee 73 0 Level input output uceessennessnnnnessnnneenenneenenne nennen 800 mV p 10 Relorn lass IinpUl cnennse na gt 17 dB 5 270 MHz Connections Video Inputs Component VPORTS seen 3 Cinch sockets Eee er 1 Ci
19. selected services manual are passed through e Activate the filter function by selecting manual e Press the MA button 20 PADE 4001 gt All services from the ASI input will be read and then displayed with name and type of the service gt If no service is found the following message will appear in the dis play no Service In this case check previously adjusted settings for the cassette and the components connected to the ASI input gt The display shows e g Bx2 TV 01 04 Das Erste Meaning of the indicators in the example TV Television type of service 4 The currently selected service is passed through 01 04 The Ist of 4 services is being displayed Das Erste Name of the service Further possible terms displayed ASI ASI station filter RA Radio type of service For radio stations the background of the screen of the connected TV or test receiver is darkened The currently selected service is blocked NE The star means that the service selected is scrambled gt If a service number e g 131 appears instead of TV or RA this indicates that an unnamed service or an undefined transport stream is being received e Use the RI E buttons to call up the services in sequential order then use E E buttons to pass through indicated by or to block them gt If the filter function is activated setting manual only servic
20. t Directive relating to electromagnetic compatibility 2014 65 EG Richtlinie zur Beschr nkung der Verwendung bestimmter gef hrlicher Stoffe in Elektro und Elektronik Altger ten Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment N rnberg 22 August 2013 Michael Bierschneider Leiter Entwicklung Manager Development Directeur D veloppement 72 PADE 4001 Service Phone 49 0 911 703 2221 Fax 49 0 911 703 2326 Email service gss de Grundig SAT Systems GmbH Beuthener Stra e 43 D 90471 N rnberg m Alterations reserved Technical data E amp O E by GSS GmbH V5 27112013
21. tory RESET SOFT RESET Via this menu you get access to the submenus to reset all settings to the factory defaults or to perform a soft reset cassette restart Bx 2 FACTORY Defaults gt Bx 2 FACTORY STORE gt M FACTORY RESET e Press the J button gt The Factory Store submenu is activated Bx 2 FACTORY STORE gt M e In order to perform a factory reset press the J button ass 24 PADE 4001 gt The cassette is reset to factory defaults The display shows STORE gt Back to Selecting the cassette page 14 e In order to perform a soft reset cassette restart or to return to the main menu Factory Default press the MODE button gt The Reset submenu is activated SOFT RESET In this submenu you can perform a soft reset cassette restart Bx 2 RESET RESET gt M e In order to perform a soft reset cassette restart press the IM button gt The cassette is restarted gt By pressing the MODE button you will be returned to the main menu Encoder without saving the factory defaults page 15 SAVING SETTINGS e Press the M button gt Return to Selecting the cassette page 14 gt The settings are saved ass 25 PADE 4001 6 FINAL PROCEDURES After installing the head end station upgrading accessories or installing cas settes it is necessary to tighten all cable con
Download Pdf Manuals
Related Search