LCD Digital Video Recorder
Contents
1. STEP2 Place the LCD monitor face down on a soft protected surface STEP3 Remove all cables connected to the DVR module STEP4 Remove the two screws which are used to fixed the module to the LCD monitor STEP5 Hold the BNC connector s for video and pull the module gently to the direction as indicated below Then the module is slid out 282. BACK gt NEXT ENTER Note This DHCP function needs to be supported by a router or a cable modem network with DHCP services and a DDNS account to correspond the dynamic IP address to a specific Hostname for this function to work properly 4 8 BACKUP In this menu list you can choose to make a copy for a specified period time to a compatible USB flash drive for your own purpose Note Before making a video backup with audio you need to make sure whether there s any audio camera connected to the channel which supports audio recording and there s any recorded data for the channel 4 8 1 USB BACKUP Before making USB backup please check if a The USB flash drive is supported by your DVR If not the message USB ERROR will be shown on the screen For the list of the compatible USB flash drives please refer to APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST at page 26 b The format of your USB flash drive is FAT 32 If no please format it to FAT 32 in your PC c There is no data in the USB flash drive If yes it s recommended to clear all data in the USB flash drive before starting the backup Note When USB backup starts it s not allowed for OSD menu operation or network backup in order to keep the consistency of the video data Note You can backup up to 2GB video data for one time USB backup To backup more data please set the 2 3 4 9 6 time amp channel
3. PASSWORD Set the username and password subscribed from your ISP supplier 14 3 4 DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security See the example below PPPOE NETWORK TYPE USER NAME PASSWORD IP GATEWAY NETMASK PRIMARY DNS SECONDARY DNS PORT PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t SELECT BACK gt NEXT ENTER Note The PPPOE function needs to have one username and one password subscribed from one ISP Supplier and a DDNS account to correspond the dynamic IP address to a specific Hostname 4 7 3 DHCP 1 2 3 NETWORK TYPE Select the network type as DHCP DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security See the example below NETWORK TYPE IP GATEWAY NETMASK PRIMARY DNS SECONDARY DNS PORT PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT
4. 24 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS ty lt gt MOVE SELECT X axis 0 24 hours Each time interval within a square is two hours divided into four 30 minutes Y axis Monday Sunday Operation Move to the start time point and press lt to set the start time point marked in red color Then press a w 4 to set the timer recording schedule After setup press again to create an ending time point marked in yellow color and press Menu to exit Note This function here is only for detection timer setup and activation 4 4 DETECTION In this submenu you can set up detection related functions Move to DETECTION and press 4 The screen will show the following submenu items 1 TITLE Show the camera title of each channel set in CAMERA 2 DET The available options vary depending on the model you have For Model 1 2 Select if you want to activate the motion detection function for the selected channel ON OFF For Model 3 amp 4 Select HIGH NORMAL LOW to activate the motion detection function with different sensitivity for the selected channel or select OFF to disable this function 3 AREA Press ENTER to set the detection area You will see similar screens as the following Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection There are two different methods to set the detection area d
5. A A O AA aaa a 14 A A o ae ee E Re ee eee eee 14 O O A AA AA AA RR RRR A MAS NRA AA AA 14 AA 15 MO BAG UR ia Ea AA AA AA ee ey ee ee ee en ae eee 16 4o USB BACKUP maa LAAN ANG AGAR NAA AA AA kaa 16 A a cal NA 17 Os ee MICO VIC We ainda AA AA AA AG 17 5 1 1 Installation amp Network Connection saaan AA AA AA AA 17 ya Papas CONTO caro AS SAS AS AAA AO RATA AAA ee een eee 18 E AO A A O A EN 19 92 lE VV GD BIOWSE Tintin oc 22 O e aa o E AE E ONO 24 APPENDEI1SPECIFICATIONS maa AG AG ANN ANG IAANGAT 25 APPENDIX 2 COMPATIBLE USB FLASH DRIVE LISTA NALANG a o e aa 26 APPENDES 3 COMPATIBLE SATA HDD LISTA AAP AA AA AA AN AA AA AA 27 APPENDIX A DYR MODULE REMOVAL a AA AA A AA A AA a 28 1 KNOWING YOUR LCD DVR 1 1 Rear Panel Below shows the illustration when the DVR module is installed in the LCD monitor view from bottom to top Note For how to install the DVR module to the LCD monitor please refer to 2 2 Install DVR Module to LCD Monitor at page 4 For how to remove the DVR module from the LCD monitor please refer to APPENDIX 4 DVR MODULE REMOVAL at page 28 Model 1 G 9 6 STRT IH siii o o j A p e LAN PC O o Bi ae VGA IN VGA EXTERNAL USB a a LCD Monitor DVR Module Ta 1 r Eb B AC POWER Connect to power with the supplied LCD monitor power cable VGA OUT Connect the monitor directly to this jack on the DVR module LAN Connect to network with a net
6. Apple Mac Step 1 Step 2 Step 3 Go to Apple s official website to download QuickTime The website address is as follows http www apple com quicktime win htmil a Click Free Download to go into the download page and select to download the free player b Leave your Email address and click Free Download Now to download the latest QuickTime player c When the download is completed execute the Quick Timelnstaller exe file and follow the on screen instructions to finish the installation procedure Open your QuickTime player Select File Open URL in New Player and key in the URL address The URL format is rtsp ipaddress live h264 For example rtsp 59 124 231 75 live h264 Click OK to continue content guide 12 16 2008 mov File Edit Movie Favorites Window Help Frae TV gt Store Only South Park The First 10 BREE Ce en LON oS HBO Zest kg Co lactions amp pe TO Sant for Under 315 e lt A aan Specia Prang A IRA Mores of Ue o f h Mamma Miz j i Pa New cleaac Mov wo BEN D ESCENES with The Mummy N A Na New Relcasc M vi d Cheetah Girls 3 New Release Move ET mT sa Download 2 Pussycat Dolls Games for your Phone or iPod Touch Click Here ss Po dk JAN 1 A pop up window will appear and prompt you to enter the authentication information Note If you re not prompted to enter t
7. We reserve the right to revise or remove any content in this manual at any time We do not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of this manual For the actual display amp operation please refer to your DVR in hand The content of this manual is subject to change without notice The product amp company names mentioned herein may be the registered trademarks or tradenames of their respective owners Version Firmware 1142 1039 1013 1026 0A 0000 Video Viewer 0119 TABLE OF CONTENTS 1 KNOWING YOUR CCD DURAN td ld 1 TM ae elle UI sai AAA A a 1 1 21 Remote Controller AO AS A AAA ds 3 NAO AS O A A A A A 4 AA A e mace ce Sead oad nals east eee A E caste cas thie erating sa aol eae earl 4 2 2 Msta DVR Module to EGO MONO accesses aaa AN saan aa AA eames AE 4 2 3 CONNEC ames a A AGA bsa 5 PA AA antueraeen Sena come ea caecieaata ote 5 2 9 Sel Dale aNd TIME GAAN AA AA a 5 PA O Aso Wi Ol O CERO EE AA AA a a a APA 6 a oo to Oa OPERATION o iaa Aang 7 Oa SUI Te ACI it oie ceca segs stapes mms E em geese eee eet AA T A a AA AA T SASA NG A A A RP A A nee en Ry SE T E E A E E A A See eee erry Ore ee O A T e 8 a AA AG DUDO AA 8 ADVANCED OPERATION sonara 9 a OO ES Ann uo Aa A 9 12 RECORD o e ido 9 A A Aa a o A A AA 9 42 2 Detaled record SEHING ii A AAA AAA a a aL 9 Poo A AO 10 AA DETECTION A e osa 11 AO REMOTE sele ciodimodel On A zas 13 OSOS TE MANE O ip ES 13 74 A A
8. being downloaded to the PC or notebook To simply backup images without previewing deselect the checkbox Simultaneous Playback You will only see a message box indicating the total time needed the current status and the saving location Download Cancel Click Download to start or Cancel to discard the video backup 21 5 2 IE Web Browser Note The supported PC operating systems are Windows Vista XP 2000 Step 6 Key in the IP address used by your DVR in the URL address box such as 60 121 46 236 and press Enter You will be prompted to enter the user name and password to access the DVR If the port number your DVR used is NOT 80 you need to key in the port number additionally The format is jpaddress portnum For example for IP address 60 121 46 236 and port No 888 please key in http 60 121 46 236 888 into the URL address box and press Enter Step 7 Enter the user name and password the same as the ones used for video viewer login and press OK You will see a screen when the login information is correct Note The buttons and functions described below may differ from the actual ones and are for selected model s only Q H264 DVR a a 2 eeee hal la it dal 00009000 OOO 5 mame Click to go to the main page of the DVR Click 2 to go to the detailed DVR setting PTZ Click EA to enter the PTZ mode Channel Selection ge Click one of the number to swit
9. get 4X slow playback and twice to get 8X slow playback H 264 QuickTime QuickTime is Apple Inc s multimedia software You need to have QuickTime installed in you operation Web Transmission system first When QuickTime is selected you will be promoted to enter the user name and password to access the server of the DVR BEST HIGH NORMAL BASIC 16 Change Quality Click to change the image quality 4 CIF CIF 17 Change Resolution Click to change the image resolution 4CIF 704 480 CIF 3527240 Audio Channel To hear the live audio remotely click 1 2 3 or 4 8 means no camera supporting audio is connected to any audio channel Selection This function is available only when your DVR supports the audio function and a camera supporting Selected model only audio is connected correctly to the DVR Note To know whether your DVR supports the audio function please refer to APPENDIX 1 SPECIFICATIONS at page 25 23 5 3 QuickTime Player You can also use the QuickTime player to remotely log into the DVR and check the live view only Note QuickTime is Apple s multimedia software You need to have QuickTime installed in you operation system first and you can access the DVR to see the live view If you have installed QuickTime please skip Step 1 Note The latest version of QuickTime is V6 4 at the time this manual goes to press and the supported operation systems are Windows Vista XP 2000 and
10. s you want and start USB backup again Move to BACKUP and press lt You will see the following submenu items START TIME Select the start time of the backup END TIME Select the end time of the backup AVAILABLE SIZE Display the available capacity in the inserted USB flash drive CHANNEL Select channels by pressing 4 button to change the symbol in front of the channel number Symbol means that this channel is selected to backup Symbol means that this channel is not selected to backup HDD NUM Select the HDD containing the data you need START Press to start copying the chosen data to the USB flash drive Backup Video Playback on PC During the backup process a file player installer will also be copied into your USB flash drive After the backup is completed BACKUP SUCCESS will be prompted on the screen Insert your USB flash drive into your PC and find the file player installer PLAYER EXE Double click the installer to install the file player by following the on screen instructions Then double click any backup file to play it directly in your PC and see if the backup is successful Note The supported PC operating systems are Windows Vista XP 2000 16 5 REMOTE OPERATION You can also control the DVR remotely via the supplied licensed software Video Viewer hereafter called the Video Viewer IE web browser and Apple s QuickTime p
11. the DVR side and the recordings will be saved in the specified location Playback To play a recording click and select the Record tab or Backup tab A list of all the recordings will be shown by defaults and you can also sort out the logs you want to speed up the search time Ez Status List Range Unit Record Backup Event Event User User User User Motion Motion Motion User User User User User User User Time Range Start Time End Time IF 192 165 1 12 192 168 1 12 192 168 1 12 Noa acl no ao lala 192 168 1 12 192 165 1 12 No asal 192 165 1 12 192 165 1 12 192 165 1 12 192 165 1 12 Noa as lala 192 168 1 12 20091037T atat Time 09 2308 20 41 07 09 2308 20 36 45 09 2308 20 18 56 09 2308 20 13 22 09 2308 20 05 30 09 2308 20 05 30 09 2308 20 05 30 09 2308 19 55 24 09 2308 19 48 36 092309 19 32 55 09 2308 19 24 51 09 2308 19 10 26 09 2308 19 01 05 09 2308 18 47 57 One Day Prev Next 20091037 End Time 09 2308 20 41 07 09 2308 20 36 45 092309 20 41 07 09 2308 20 36 45 09 2308 20 05 35 09 2308 20 05 35 09 2308 20 05 35 09 2308 20 18 56 09 2308 20 13 22 09 2308 19 55 24 09 2308 19 48 36 092309 19 32 55 09 2308 19 24 51 09 2308 19 10 26 Record Type M User Y Motion M Alarm wW RETR File Path C temprideo20080923 204107_off C tempryideo20060923203045_off C temprideo20060923201656_off Citempryideo200609
12. 23201322_off Ci temprideo 20080923200530_off C temprideo20060923194636_off Citempryideo20060923195524_o1f C tempvideo 200609235195524 off Citempryideo20060923194636_off Ci tempryideo20060923193255_off Ci tempryideo20060923192451_off Ci tempryideo 20060923191026_oft Citempryideo20060923190105_off Ci tempryideo20060923104757_off 000800 o fo ff o o 0080000 o o ff o o Total Records Delete Delete All Play Repair Apply Close To immediately play a recording select a log from the list and click Play or double click the selected log Network Backup Click EP GP to go into the Backup page as follows and you can select a specific time range or event to make a video backup remotely The file s you backup will be from the current selected IP address Note Before enabling the network backup function make sure the DVR is not in the playback mode or the DVR will stop playback gam Backup 60 251 15 56 HDD Number Channel Start Time End Time File Path MASTER 1 1 O 2009 0726 14 58 52 I O 2009 0127 14 58 52 I cjdownload E M Simultaneous Playback Download Cancel E xl E Prev Page Next Page f7 System f7 Manual M Alarm M Timer M Motion 200907727 14 56 43 200907727 14 56 24 2009 0727 14 56 12 2009 0727 14 55 29 200907727 14 55 12 200907727 14 54 43 MOTION MOTION MOTION MOTION MOT
13. 9 900990905999 9 20990090990 886256260059 900990000000 999999909990 200550500900 099909909990 00900000000 000000099040 000900000000 dapa dnaacono dadanbaacaao daapapaaaaaa aoo000000005 AgaBagaaanaa 009000005008 BbaBaBapasaa 003000000008 850050000005 Goa00ce00009 322323 22288a daBadaaBaBBa Sadnan000005 baaBabaaasaa Bbapanaaaaaa coanasaaacoo Genansaacans eocccacocaoo 000000000000 990000000000 ovoveuovasa go000 000906 S0909 090999 38099090098 29999039999 509900000006 S20099999999 909009909999 2999090099 990990009 9909000090 900090000 999 ooo 900 SOGDOOIOLODY DOGpodappapa Daba napapa onoaanoapaba apoaapoapaba D0000000D0DA Da0000000000 000000000000 anaoaaasaoaa 200400008000 002000000835 200000000006 2000906090025 9 a 0 D 260000000000 Baaaaaaanaa Saaaaaaaag 298565060060 260060000000 Bagaaaaanasa 9099999000009 000089990009 900009000099 990909086009090 999996086006 000006008000 660000000800 999000090300 090999000909 DOPTOODOPTDO 999009000000 DIODI 090990009000 900990009000 999000000900 oudopGoogGa0 ooudgonaopnae doocoaog0pa00 DDODDODOODO Please read instructions thoroughly before operation and retain it for future reference L683 681 manual V0 93 IMPORTANT SAFEGUARD CAUTION RISK OF ELECTRIC SHOCK CAUTION To reduce the risk of electric shock do no
14. DIX 2 COMPATIBLE USB FLASH DRIVE LIST Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table If the USB flash drive is not supported by the DVR the USB ERROR message will be shown on the screen Note Please use your PC to format the USB flash drive as FAT32 Note You can backup up to 2GB video data for one time USB backup To backup more data please set the time amp channel s you want and start USB backup again pa oe ug 26 APPENDIX 3 COMPATIBLE SATA HDD LIST MANUFACTURER MODEL CAPACITY ROTATION Seagate ST3320613AS 320GB 7200 rpm ST33500320AS 500GB 7200 rpm WD 21 APPENDIX 4 DVR MODULE REMOVAL To remove the DVR module from the LCD monitor please follow the steps below Model 1 STEP1 Remove the LCD monitor base For details please refer to 2 2 Install DVR Module to LCD Monitor at page 4 STEP2 Place the LCD monitor face down on a soft protected surface STEP3 Remove all cables connected to the DVR module except for the external I O cable STEP4 Remove the two screws which are used to fixed the module to the LCD monitor STEPS With the external I O cable connected to the module pull the cable gently to the direction as indicated below and the module is slid out STEP5 Remove the cable Model 2 STEP1 Remove the LCD monitor base For details please refer to 2 2 Install DVR Module to LCD Monitor at page 4
15. ION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION MOTION 2009 0727 14 54 26 200907727 14 54 12 200907727 14 53 43 200907727 14 55 24 200907727 14 53 12 200907727 14 52 43 200907727 14 52 33 200907727 14 52 19 200907727 14 52 12 200907727 14 51 43 200907727 14 51 23 200907727 14 51 12 E J PI PI PIPI PIPI PI PI PI BI BI BI 6565 bI ba bo o Function Description HDD Number Channel Download by Time Download by Event Specify the hard disk HDD Number and channel number Channel within which have the video data you need Specify the time range within which has the video data you want in the Start Time and End Time columns Select an event log from the event list This list shows all logs in the o Function Description specified DVR from the latest to the earliest e To quickly find the events you need check or uncheck the event type System Manual Alarm Motion and select the log you want To view the earlier or later logs that are not shown in the current page click Prev Page or Next Page To refresh the event list click Reload File Path Assign the location where the backup files are saved Simultaneous Playback To view the backup images simultaneously when the download process is in progress select the checkbox Simultaneous Playback You will see the backup images while the images are
16. S is to set the sensitivity regarding how long one object stays in the detection area and triggers the recording Depending on the model you have you may see either of the following methods a Select a value The smaller the value is the higher sensitivity for motion detection b Select an option HIGH NORMAL 7 RE Reference Selected model only RE is to set a reference for detection The default value is 10 which means the DVR will compare 10 continuous images at one time according to the sensitivity of LS SS TS simultaneously 8 4 5 2 3 4 9 ALARM Selected model only Select N C Normally Closed N O Normally open OFF for the alarm polarity The default alarm value is OFF REMOTE Selected model only In this menu list you can set up remote devices to work properly Move to REMOTE and press lt You will see the following submenu items TITLE Show the camera title of each channel set in CAMERA DEVICE Select the device type CAMERA PTZ according to the connected camera for each channel ID Set the ID number O 255 for a PTZ camera After connecting to a PTZ camera correctly the default ID of the PTZ camera will be shown on the screen PROTOCOL Select NORMAL our protocol P D PELCO D or P P PELCO P protocol RATE Set the baud rate of each channel 2400 4800 9600 19200 57600 115200 For the connected cameras such as PTZ a
17. back mode press to slowly playback the recorded file Pause Press to pause the playback video Press to take a snapshot for the current live video image and save the image in the USB flash drive Before using this function please insert the compatible USB flash drive into the USB port on the DVR module Press to select the audio channel s you want in the live or playback mode In the live mode you can only hear the live audio in the playback mode you can only hear the recorded audio To make a video backup with audio make sure the camera supporting audio function is connected to audio input In the live or playback mode press to enlarge the image of the selected channel This function is not applicable when the display mode is set to DEFAULT Home Press to return to the home position Stop Press to stop the auto mode Auto Press to enter the auto mode of the PTZ camera Preset Enter the menu to set the preset points Speed This key is reserved for future use Goto To operate the PTZ camera to a specific preset point press GOTO and the number of the point you want Zoom Press one of them to adjust the optical zoom in out ratio of the PTZ camera Focus Press one of them to adjust the focus of the PTZ camera 2 CONNECTION AND SETUP Note The DVR is designed to automatically detect the video system of the connected cameras NTSC or PAL To make sure the system detection is correct please check i
18. ch to the channel you want to see in full screen Click Or A to go to the previous next channel or change setting Display Mode cok Click to show 4 cut display Click to display each channel one by one starting from CH1 When the last channel is displayed it will start from CH1 again To exit from this display mode press any other channel display button Menu and Arrow Keys Click to enter the menu exit the menu mode Move the cursor up down to select the previous next menu or sub menu function or change the setting Move the cursor left right to the previous next sub menu items Click B to enter the playback search settings screen Snapshot Click Ll to take a snapshot for the current view and open another browser window to display the captured image mpa Lock Click to enable the DVR key lock function To unlock the DVR key in your password and press Ej Click to confirm the setting or enter your selection Digital Zoom Click to zoom in out the selected channel image 22 O Function Description 13 Search Click to enter the DVR full search menu You can check all the logs here and select one of them to payback U Stop Play a Rewind Forward T Pause Slow Playback Playback control Rewind Forward Click once to get 4X fast rewind forward twice to get 8X three times to get 16X and four times to get buttons 32X the highest Slow Playback Click once to
19. d press button to search and directly playback the recorded files 4 2 RECORD In this menu list you can set record settings Press Menu on the front panel The default admin password is 0000 Enter the default password and press lt 4 2 1 Quick record setting 1 2 3 Move to QUICK START gt RECORD The screen will show the following submenu items IMAGE SIZE Select FRAME FIELD Selected models only or CIF QUALITY Select one of the four quality options SUPER BEST BEST HIGH 4 NORMAL IMAGE PER SECOND Select the images per second for MANUAL RECORD 4 2 2 Detailed record setting 1 2 3 4 9 Move to ADVANCE gt RECORD and press The screen will show the following submenu items MANUAL RECORD ENABLE Start stop the manual recording function EVENT RECORD ENABLE Start stop the event recording function When this function is enabled the recording will be triggered by any motion or external alarm TIMER RECORD ENABLE Start stop the timer recording that is activated according to the scheduled time EVENT RECORD IPS Select the images per second for EVENT RECORD Recording that is triggered by alarm or motion TIMER RECORD IPS Select the images per second for TIMER RECORD Recording that is activated according to the scheduled time 6 7 PRE ALARM RECORD Select to enable or disable the pre alarm function ON OFF When pre a
20. ent Search Press LIST to show the list for all types of the recorded files Choose the item you want to see and press to start playback Search by Time Press Menu to enter the menu list and go to ADVANCE gt EVENT LOG Move to QUICK SEARCH and press to enter the quick time search menu You can search any specific events by time Year Month Day Hour Min and directly play the file you find 3 5 Firmware OSD Upgrade Step 1 Format the USB flash drive as FAT32 format first Step 2 Get the upgrade files from your distributor and save the upgrade files in your USB flash drive do not change the file name Step 3 Insert the USB flash drive into the DVR USB port Step 4 Press Menu and move to ADVANCE gt SYSTEM INFO Move to UPGRADE and press Gt Step 5 Select YES and press again to confirm upgrade Step 6 Remove the USB flash drive after the system is rebooted ADVANCED OPERATION 4 ADVANCED OPERATION 4 1 1 2 3 QUICK SEARCH You can search any specific events by time and directly play the file you find from the DVR Move to QUICK SEARCH and press You will see the following submenu items DATE Select the specific time period YEAR MONTH DAY HOUR MIN that you want to search SEARCH HDD Change to the HDD you want if there are more than 1 HDD in your DVR START Move to START an
21. epending on the model you have 11 Press 4 to choose the width of the detection area Transparent blocks are the area under detection Press a w to choose the You can also set up multi detection area When any movement is detected you will height of the area see the grids are flashing Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection Model 2 7 E s Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection There are three detection areas for your choice Press a or 4 once to broaden the detection area Press v or once to narrow the detection area 4 LS Level of Sensitivity Selected model only LS is to set the sensitivity of comparing two different images The smaller the value is the higher sensitivity for motion detection 5 SS Spatial Sensitivity Selected model only SS is to set the sensitivity for detecting the size of one object the number of the grids on the screen The smaller the value is the higher sensitivity for motion detection Note The default setting of 5S is 03 which means once an object is detected more than 3 grids the system will get triggered So the value of SS must be less than the number of grids that you set up for the motion detection area 6 TS Time of Sensitivity Selected model only T
22. er 4 Slide the DVR module to the slot as indicated below Push the module to the end and fix it with the supplied screws 6 Connect the VGA cable on the LCD monitor to the VGA port on the DVR module a VGA Cable VGA Port anLCD onDvR f Monitor Module Replace the monitor base as indicated below a Replace the screws loosened in the first step b Hook the screw cover removed in the first step to the monitor and push it downward to lock it 2 3 Connect Camera The cameras must be connected and power supplied before the DVR is powered on The DVR will automatically detect the video system of the connected camera s NTSC PAL and switch itself to the correct system 1 Video cable connection Connect the camera video output to the DVR video input port with a coaxial cable or RCA cable with BNC connector 2 Audio cable connection if your camera supports the audio function Connect the camera audio output to the DVR audio input port with a coaxial cable or RCA cable with BNC connector 3 Power connection Connect the camera with indicated power supply 2 4 Power On Find the power cable supplied with the LCD monitor and connect it to the power jack AC POWER on the LCD monitor and to the power outlet The DVR will be on and initialized Note Before the DVR is powered on make sure the cameras are connected and power supplied for the detection of the camera video system to be correct Note To ensure
23. f the cameras are connected to the DVR and power supplied before the DVR is powered on 2 1 Install HDD One SATA HDD should be installed in the DVR module and it must be purchased separately Step 1 Loose the screws on the upper cover and remove it Step 2 Find the thermal conductive silicone rubber in the accessory pack and paste it to the protrusive surface on the module Step 3 With the PCB side facing up connect the compatible SATA HDD to the data bus and power and place it in the module Step 4 Find the two screw holes on the module and fasten the HDD to the module with the supplied screws one for each side Step 5 Close the upper cover of the module and fasten all the screws you loosened in Step 1 thermal conductive silicone rubber EE Remove the DVR module cover Paste the thermal conductive silicone Connect the HDD to the power cable amp data rubber to the DVR module bus cable and fasten it to the DVR module 2 2 Install DVR Module to LCD Monitor After the HDD is installed in the DVR module place the module to the LCD monitor Note The illustration below is taking Model 2 as an example 1 Place the monitor face down on a soft protected surface 2 Remove the LCD monitor base as indicated below a First snap off the screw cover from the monitor base b Remove the four stand screws 3 A slot on the rear panel of the LCD monitor is reserved for the DVR module Find the slot and remove the slot cov
24. he authentication information and the error message 10060 appears go to Edit 3 Preferences 3 QuickTime Preferences and select Streaming Transport front he drop down list Select Use HTTP and keep the port ID as 80 Step 4 Key in the user name and password for accessing your DVR The user name and password are the same as the ones you use to log into Video Viewer If the information is correct click OK to go on If not click Cancel to quit the accessing If the information is correct press OK to go on If not press Cancel to quit the accessing When the login is successful you will see the live view 24 APPENDIX 1 SPECIFICATIONS LCD Panel Size 18 95 diagonal Resolution WSXGA 1440 x 990 pixels Aspect Ratio 16 10 Peak Brightness 300cd m Typical Contrast Ratio 1000 1 Typical Number of color 16 7M Response time 5 ms Tr Tf Typical Viewing Angle 85 85 80 80 CR 10 Powerful Scaling and Zooming Engine YES Down Up Scale Support YES Full Screen 16 10 IR Control RCU YES Built in 1 speaker 1 Watt DVR H 264 H 264 Licensed software Video Viewer Internet Explorer or Mozilla Firefox Web Interface web browser QuickTime player 20 users access simultaneously e e how Gn YES Power Consumption 22W A3 L X3702 H X 195 20 Optional Peripherals Keyboard controller The specifications are subject to change without notice 25 APPEN
25. isplay when you re in the PTZ mode 0 9 1 Press to switch to the channel you want 2 In the keylock mode used to key in the DVR password 3 In the PTZ mode used with the key Goto to have different functions Applicable only for selected model Press to enter the LCD monitor s menu to adjust some setting parameters You will see the icon WW on the display when you re in the monitor adjustment mode 1 Press to enter the DVR menu in the DVR mode or PTZ camera menu in the PTZ mode 2 In the DVR or PTZ menu press to exit the menu setting Press to switch the channel display in the 4 cut 9 cut 16 cut mode Press to switch the channel display one by one in the full screen and press again to quit The channel s with video loss or covert recording will be skipped when you re in the SEQ mode A V 4 B In the menu press to move the selection up down left right A V In the setting mode press to change the function setting Press to enter the sub menu or confirm your selection Press to quickly search the recorded files by four event lists RECORD LIST MOTION LIST ALARM LIST TIMER LIST or select FULL LIST to show all the event logs Select the log you want and press 6 to play the selected file Play Press to play the recorded video Rew Press to fast rewind the playback video FF Press to fast forward the playback video Stop Press to stop the playback video Slow Under the play
26. larm and event recording functions are both activated the DVR will record 8MB data before an alarm motion event is triggered 7 OVERWRITE Select to overwrite previous recorded data in your HDD When the HDD is full under the O W recording mode the DVR will clear 8GB data from the oldest for continuous recording without notice 4 3 TIMER In this menu list you can schedule different sets of time for recording and detection function Move to TIMER and press lt Select to enable ON or disable OFF the recorder timer and or detection timer functions 1 RECORD TIMER Use a w to change the setting ON OFF When it s set to ON press to go to its submenu for further settings RECORD TIMER 10 12 14 16 18 20 22 24 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS ty e gt MOVE lt lt SELECT X axis 0 24 hours Each time interval within a square is two hours divided into four 30 minutes Y axis Monday Sunday Operation Move to the start time point and press lt to set the start time point marked in red color Then press a y 4 to set the timer recording schedule After setup press again to create an ending time point marked in yellow color and press Menu to exit 2 DETECTION TIMER Use a to change the setting ON OFF When it s set to ON press to go to its submenu for further settings DETECTION TIMER 10 12 14 16 18 20 22
27. layer ONLY when your DVR supports the network function Note The buttons and functions described below may differ from the actual ones and are for selected model only 5 1 Video Viewer 5 1 1 Installation amp Network Connection 1 2 Install the software Step1 Place the supplied CD into your CD ROM or DVD ROM drive The program will be automatically run Step2 Click Licensed Software AP to install Video Viewer immediately or click Download The Latest Version under Licensed Software AP to download the latest version of Video Viewer from the Internet User s Manual amp AP paaa 1 ES Users Manual fa Download The Latest Version Quick Start fa Download The Latest Version Licensed Software AP fel Download The Latest Version Step3 Follow the on screen instructions to finish the installation When the installation is completed a shortcut icon 422 will be placed on your PC desktop Network Connection gt Local Connection via LAN LAN is used when it s the first time to remotely access the DVR and you need to configure the network setting of your DVR based on your network type in advance a Connect the DVR to your PC via a RJ45 network cable The default DVR values are as follows Item Default Value IP address 192 168 1 10 User name admin Password admin Port 80 b Set the PC s IP address as 192 168 1 XXX 1 255 except 10 in order to make the PC and DVR under the same d
28. nd speed dome cameras etc please make sure their baud rate setting is the same as the setting here 4 6 SYSTEM INFO 1 2 3 4 9 6 1 In this menu list you can check or change some system settings The submenu items are described below SERIAL TYPE Selected model only Show the serial type of the DVR RS485 BAUDRATE Selected model only Set the baud rate of the DVR 2400 9600 19200 38400 57600 115200 HOST ID Selected model only Set the ID of the DVR 0 254 PASSWORD Press to reset the password for accessing the DVR system You can set the password up to 4 digits RESET DEFAULT Press to reset all settings as default and select YES to confirm or NO to cancel CLEAR HDD Select the HDD you want to clear Press Gt and select YES to confirm to clear HDD or NO to cancel UPGRADE Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 format first Then save the upgrade file in a compatible USB flash drive and insert it into the USB port at the front panel Press lt and select YES to confirm upgrade or NO to cancel Note To use this function you need to have the upgrade file saved in a compatible USB flash drive and insert it into the USB port at the front Note Do not disconnect the power of your DVR while the upgrade process is in progress or the DVR functions may not work
29. normally or be unable to use 8 AUTO KEYLOCK SEC Set the time out in second after which the key lock function is activated NEVER 30 60 120 9 LANGUAGE Select the language of the OSD 10 VIDEO FORMAT Here shows the information of the DVR video format NTSC PAL 11 VERSION Here shows the firmware version information 4 7 NETWORK In this menu list you can set up the network Move to NETWORK and press to enter the submenu The submenu items are described below 4 7 1 STATIC 1 NETWORK TYPE Select the network type as STATIC and set all the information needed in the DVR 2 NETWORK INFORMATION IP GATEWAY NETMASK Key in all the network information obtained from your ISP Internet Service Provider 3 DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider 4 PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security See the example below STATIC NETWORK TYPE STATIC IP 001 012 GATEWAY 001 254 NETMASK 252 000 PRIMARY DNS 001 001 SECONDARY DNS 055 244 PORT 0080 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t SELECT BACK gt NEXT ENTER 4 7 2 PPPOE 1 NETWORK TYPE Select the network type as PPPOE 2 USERNAME
30. omain c Double click ae icon on your PC desktop to enter the control panel By defaults the Address Book Li panel will be displayed on the right side of the control panel d Click UB Address Book gt cy Add button to key in the default IP address user name password and port number of the DVR you intend to connect OR Click ice Search gt 1 4 Refresh to search the available IP address es of other DVR s 17 under the same domain as your PC s IP address The found address es will be listed and can be added into the address book by clicking L Gi 3 Add into address book e Double click the IP address you just added into the address book to log in gt Remote Connection via Internet When the network configuration of your DVR is completed you can access your DVR remotely via Internet A a Double click se icon on your PC desktop to enter the control panel By defaults the Address Book panel will be displayed on the right side of the control panel b Click i Address Book gt ED Add button to key in the IP address user name password and port number of the DVR you intend to connect OR Click ice Search gt Si Refresh to search the available IP address es of other DVR s under the same domain as your PC s IP address The found address es will be listed and can be added into the address book by clicking AD Add into address book c Double click the IP add
31. on the DVR module 9 LAN Connect to network with a network cable 10 Audio IN Connect to an audio source such as a camera with the audio function 11 Video IN 1 4 Connect to video sources such as cameras Note If you want to make a video backup with audio please make sure whether your DVR supports the audio function and connect audio cameras to the channels which support the audio function 12 USB To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 first 1 2 IR Remote Controller POWER O m E DVR PC DVR QP Stop Slow Snap amm Audio Zoom POWER DVR PC DVR PTZ NUMBER PAD LCD adj Menu BH BA H SEQ Arrow Keys qc List Playback Keys Snap Audio Zoom PTZ Control Keys Applicable only for selected model 1 Press shortly to enter the monitor power saving mode 2 Press long enough to power off the DVR The system will prompt you to stop recording and confirm the power off when the DVR is in the record mode To power on the DVR press it again Press to switch the display between your DVR and PC Applicable only for selected model Press to switch the control between your DVR and PTZ camera if your DVR supports PTZ camera connection You will see the icon on the d
32. onfigure Cancel Button Function Description Remote Config Click to go into the detailed DVR setting Record Setting Click to go to the detailed record setting Custom Setting Click to choose the language of this program The language change will take effect when this program is closed and executed again 5 1 3 General Operation Record F Y 4 a Pa To record remotely at the same time when any event alarm is triggered at the DVR side click jip gt go to the Record Setting page mE 1 et Record OnfOH PrevfPost Event Record Time P Manual F7 Schedule F Motion i Prev Sec M Hard Disk Overwrite Baki fun Record Time Range co Schedule wo Alarm ETTTETITIT IPIT LULU ILL oO i i i TO AAA LU LE LELEEE ITOT LANG DAA AA App Ll LA IA LEE EL TL AL CO Fa In the Record Setting page you can set the following items e Record type e Hard disk overwriting e Pre post alarm record time e Record time setting e Record path If Manual is checked click EJ on the main control panel to start the manual recording immediately and the 19 recordings will be saved in the specified location The red text indication REC will be shown at the top left corner of the image display view If Motion and or Alarm are checked the recording function will also be enabled at the remote side when any event is triggered at
33. ress you just added into the address book to log in 5 1 2 Control Panel see After setting up the network information login user name and password double click o gt on the PC desktop to open and log into the control panel You will see a screen similar to the following with 7 major sections NI 2 Ap 20091077422 18 03 33 Button Function Description O Z o Click to show the predefined IP address es You can add remove or search CJ Address Book the IP address to log in the DVR remotely Two sub functions are available for this button Address Book and Search Click to show the main operation functions audio volume control color Miscellaneous Control setting backup DVR setting upgrade and find event logs For details please see Miscellaneous Control at page 19 ie Lo Click to view all event and recording logs search the desired log s by date 9 or playback the recording of the selected log 3 Record Record Stop Click to start stop the manual recording Click to take a snapshot of the current view The snapshot will be saved in the LA Snapshot PARA ag path you specified in Record Setting 18 Click to show the current network connection details TT DVR Control Click to go to the DVR control panel to operate the DVR remotely Miscellaneous Control Click Ep on the control panel and six functions are available as follows General setting and utilities Remote Config C
34. sly going on 1 Fast Forward Fast Rewind You can increase the speed for fast forward and rewind on this device In the playback mode Press FF once to get 4X speed forward and press twice to get 8X speed etc And the maximum speed is 32X Press REW once to get 4X speed rewind and press twice to get 8X speed etc And the maximum speed is 32X Note During playback the image size of the recorded data FRAME FIELD or CIF will be shown on the 2 3 4 9 screen Pause Image Jog Press Pause to pause the playback In the pause mode Press FF once to get one frame forward Press Rew once to get one frame rewind Stop Press Stop to stop the playback and return to the live view Slow Playback Press Slow to get 1 4X speed playback and press twice to get 1 8X speed playback Audio Playback Press Audio to select the audio channel you want for audio playback The available audio inputs depend on the model you have For details please check the specifications of your model Gp Playback audio of the 1st audio channel Playback audio of the 2nd audio channel Playback audio of the 3rd audio channel Playback audio of the 4th audio channel Note f you want to make a video backup with audio please make sure whether your DVR supports the audio function and connect audio cameras to the channels which support the audio function 3 4 Search 1 2 Full Ev
35. t Alarm SA R i gt Channel title E mag ay y 1st live audio 2nd live audio il 1 Gi 3rd live audio dj 4th live audio Gi 1st playback Qh 2nd playback ki channel ka channel a audio channel a audio channel Kh 3rd playback dp 4th playback Audio channel Digital zoom a audio channel g audio channel unselected mode Digital zoom HDD overwrite Timer recordin unselected 9 3 2 Recording By defaults when the HDD capacity is nearly full this device will overwrite 8GB data from the oldest for continuous recording without notice LCD adjustment 1 Manual Recording By defaults the record icon Ri or E shows on the screen when the DVR is powered on and a HDD is installed 2 Event Recording When the motion detection or alarm is activated the motion icon 53 Or Sh or alarm icon 2 or fm shows on the screen for any motion or alarm event 3 Timer Recording When the timer record is activated the timer icon E shows on the screen 3 3 Playback Press Play to immediately play the latest recorded video Note There must be at least 8192 images of recorded data for playback to work properly If not the device will stop playback For example if the IPS is set to 30 the recording time should be at least 273 seconds 8192 images 30 IPS for the playback to work properly Note The video playback at the local site might get affected and may not be so fluent if there s any remote surveillance simultaneou
36. t expose this apparatus to rain or moisture Only operate this apparatus from the type of power source indicated on the label The company shall not be liable for any damages arising out of any improper use even if we have been advised of the possibility of such damages Graphic Symbol Explanation The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons N This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance R The crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste Contact your local dealer for procedures for recycling this equipment All lead free products offered by the company comply with the requirements of the European law on the Restriction of RoHS Hazardous Substances RoHS directive which means our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive This apparat
37. tal Video Recorder LCD D igi USER MANUAL S aoacooa 90000000 20990000 209000000 609000090 299000000 920900900 200900000 9099900900 900000000 999000900 002005959099 999990500099 090909000999 pogaaooannoo DODODODOa nDo BBoponoa ano 60000pn00000 BoaaaaaapaDo DoDococnDono Gapepooapeds oanoDoDanDao coannnponoan aoeaaansacaa copocacososa cansoassanoa apanoooapaoa o000000a0000 aoanoaaonaoa 200000000000 090000000000 9009000 9090009 9990099 999000 99999999009 99993999999 90909090099 99999099099 90909000000 99909990999 9999999 999999999909 900900000000 952255055055 000090000000 oeapensIooUD panpapa popa acocononopDo 0000000D0DDO aDDADABDODDO 400000000000 p02000000000 Baanapapapoa Baanapanaona naaapaasaco aaonapaaanoo aaoCapaadaco aaHaapaaaano ao0aopaadaco abhaaaaaaano 059000agaaso Baaadadaaaas baaadaonaaco llncanocoacaco a2ap2g635223 ov 0090000000 EESPERE dovsvoupsgce D909 RSE RES B338 aBapasao bo0009009009 B338 09909909 b900 09000009 5353385909 99090000009 5333522538 999909990 3322588 NG S80 gaso 2222322 225355 388985 eaba 222228 Peete 522239 030000 aeaee J ca02000 3988286 5282988 opacsscas os psanoade vo09009000900 DODIIDODIIIO 20990000000
38. that your LCD DVR works constantly and properly it s recommended to connect the power to an UPS Uninterruptible Power Supply for continuously operation Optional 2 5 Set Date and Time After the DVR initialization is completed set the date and time first Press Menu and enter the password to go to the menu list The default password is 0000 Move to DATE and you can set the date time daylight saving in the DATE menu list Otherwise the recorded data will be disordered and you will not be able to find the recorded file to backup by time search If users change the date or time accidentally when the recording function is activated it s recommended to clear all HDD data and start recording again 2 6 Set Password Press Menu and enter the password to go to the menu list Then move to ADVANCE to enter the advanced setting menu In the ADVANCE menu move to SYSTEM INFO Select PASSWORD and press to enter the submenu to set the password four digits The default password is 0000 3 BASIC OPERATION 3 1 Live Page There are three modes available for the layout of the image display Below shows the default layout which presents the best ratio for surveillance without image distortion and the frequently used status icons for each channel are placed at the left or right side of the screen System Status Available time bar HDD capacity Recording y g
39. us is manufactured to comply with the radio interference requirements MPEG4 Licensing THIS PRODUCT IS LICENSED UNDER THE MPEG 4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR i ENCODING VIDEO IN COMPLIANCE WITH THE MPEG 4 VISUAL STANDARD MPEG 4 VIDEO AND OR ii DECODING MPEG 4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON COMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG 4 VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA LLC SEE HTTP WWW MPEGLA COM GPL Licensing This product contains codes which are developed by Third Party Companies and which are subject to the GNU General Public License GPL or the GNU Lesser Public Licence LGPL The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding author Further source codes which are subject to the GPL licenses are available upon request We are pleased to provide our modifications to the Linux Kernel as well as a few new commands and some tools to get you into the code The codes are provided on the FTP site and please download them from the following site or you can refer to your distributor ftp ftp dvrtw com tw GPL AV074 Disclaimer
40. work cable EXTERNAL I O Connect the supplied external l O cable for video audio alarm and external device such as PTZ camera connection Each connector is labeled as follows Label Meaning Description V1 V4 Video Input 1 4 Connect to video sources such as cameras A1 A4 Audio Input 1 4 Connect to audio sources such as cameras aici OO REGA equipped with the audio function es l m apat led Alarm Connect alarm input 1 4 and GND connector with Alarm Input 1 4 wires Once an alarm is triggered the DVR will start recording the corresponding channel and the buzzer will be on dl dl ol al dl 123400 ee A Ea A 4 Channel 4 G Alarm GND Ground O Alarm Output A amp B RS485 A Used to connect to a PTZ camera keyboard RS485 B controller or other compatible external device PC VGA IN Connect the DVR module and your PC with an additional monitor video cable to switch the display between the DVR and PC USB To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port 1 Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 first Model 2 7 AC POWER a A E EL INR e ee PP HT a 0000000 ki AG LAN POWER 1 Pia l IN LCD Monitor DVR Module Connect to power with the supplied LCD monitor power cable 8 VGAOUT Connect the monitor directly to this jack
Download Pdf Manuals
Related Search