1. Introduction
Contents
1. 2 0 Single Slot Card Reader User s Manual 5 Regulatory Compliance FCC Conditions CE This equipment has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation This equipment is in compliance with the requirements of the following regulations EN 55 022 CLASS B WEEE Information For EU European Union member users According to the WEEE Waste electrical and electronic equipment Directive do not dispose of this product as household waste or commercial waste Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country For information on recycling of this product please contact your local authorities your household waste disposal service or the shop where you purchased the product rE CE 102. Boost by these steps 1 2 Open Windows Explorer and navigate to My Computer Right click on the removable disk representing your card reader and click Properties Click the ReadyBoost tab and make the configurations If the ReadyBoost tab is not available then the memory card doesn t support Windows ReadyBoost Once ReadyBoost is enabled you can remove the card reader at any time without causing problems or losing data All you will lose is the extra performance that Windows ReadyBoost offers and you will get the performance back when you re plug the card reader USB 2 0 Single Slot Card Reader User s Manual If the card is then used in another Vista computer with a different space reserved for ReadyBoost when you re insert it to the original computer you will still get the performance because the system will remember your allocation 4 Specifications 4 Specifications Items Descriptions Supported Cards SD specification v1 0 1 1 2 0 e Direct access SD e Using adapter Mini SD Micro SD T Flash MMC specification v3 x v4 0 v4 1 v4 2 e Direct access MMC HS MMC MMC Plus e Using adapter RS MMC MMC Micro MMC Mobile Host Interface USB 2 0 A Type male connector Socket One SD MMC socket Transfer rate Up to 480 Mbps via USB 2 0 up to 12 Mbps via USB 1 1 Certification CE FCC Specifications are subject to change without further notice USB
3. USB 2 0 Single Slot Card Reader User s Manual Safety Instructions Always read the safety instructions carefully E Keep this User s Manual for future reference E Keep this equipment away from humidity E f any of the following situation arises get the equipment checked by a service technician e The equipment has been exposed to moisture e The equipment has been dropped and damaged e The equipment has obvious sign of breakage e The equipment has not been working well or you cannot get it work according to User s Manual Copyright Statement No part of this publication may be reproduced in any form by any means without the prior written permission Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies Disclaimer Information in this document is subject to change without notice The manufacturer does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage including but not limited to special incidental consequential or other damage All trademarks trade names and copyrights are properties of their respective owners January 2007 Ver 1 0 Table of Contents A O 3 A AO 3 Package Contents A are ees 3 System Requirements nense psn el ER E 4 2 Installation eases a ck A 4 Wide WS ces eat cu eh ccc E el hl e
4. ardware icon in the system tray to safely remove the device Caution Before removing a memory card or unpluggin the card reader from your laptop make sure that no file is being accessed by an application or being copied 2 Installation 1 In the notification area right click the unplug eject icon and select Unplug or eject hardware or Safely Remove Hardware Safely Remove Hardware 10 36 4M 2 Select the device you want to unplug then click Stop and OK 3 When Windows notifies you that it is safe to do so click OK and eject the card reader from your computer Under Mac For Mac remember to drag the corresponding icon representing the card to the trash can before extracting a card When prompted click OK and now you can extract a card USB 2 0 Single Slot Card Reader User s Manual 3 Using Windows ReadyBoost To use Windows ReadyBoost first you should make sure your memory card is ReadyBoost capable as follows m Must have 2 5 MB s random read performance for 4 KB reads across the entire device NH Must have 1 75 MB s random write performance for 512 KB writes across the entire device Some memory cards have fast parts and slow memory and this type of card isn t supported Actual requirements such as the card s minimum storage capacity depend on Microsoft Always consult with the supplier of your memory card to ensure the card is ReadyBoost compatible To use ReadyBoost 1 With your
5. memory card inserted plug the card reader to the USB 2 0 port of a computer that is installed with Windows Vista 2 When the AutoPlay dialogue box appears select Speed up my system to configure and enable Windows ReadyBoost If your card isn t ReadyBoost compatible you will not see the Speed up my system option AutoPlay o o ea Removable Disk F 7 Always do this for video files Video files options Paai Import pictures a Play General options bh Open folder to view files Po using dows Explore Speed up my system Set AutoPlay defaults in Control Panel 3 Using Windows ReadyBoost On the ReadyBoost tab click Use This Device and then move the slider to choose how much of the available space on your flash drive you want to reserve for boosting your system speed Then click OK s Removable Disk F Properties Ex General Tools Hardware Sharing ReadyBoost Customize B Speed up your system by utilizing the available space b on this device Do not use this device O Use this device Space to reserve for system speed While the device is being used for system speed the reserved space will not be available for file storage Windows recommends reserving 2430 MB for optimal performance Please read our privacy statement online If the Windows ReadyBoost option doesn t start automatically you can manually enable Windows Ready
6. pports high speed and high capacity memory cards e g SDHC Class 6 MMC 4 2 High performance SD reading speed up to 20MB s Supports USB 2 0 transfer rate of up to 480 Mbps Supports hot plugging amp Plug and Play No additional driver installation required Package Contents USB 2 0 Single Slot Card Reader x1 E User s Manual x1 USB Cable Optional x1 USB 2 0 Single Slot Card Reader User s Manual System Requirements E IBM compatible Pentium 233 MHz or faster PC amp Mac with USB port m Windows ME 2000 XP Vista Mac OS 9 x 10 x 2 Installation To use the card reader no additional driver installation is required Simply plug the card reader into your computer s USB port and it s ready to use Make sure to insert your memory card in correct orientation with the gold contacts facing down to ensure the card can be detected Under Windows When the card reader is inserted to your computer a removable disk icon with an assigned drive letter will appear in My Computer You can write and read files to and from the card in the device as you would with an ordinary disk drive Under Mac The inserted memory card will mount to the desktop and appear as removable media devices The name and appearance of each icon depends on the card s format and label UNTITLED Removing a Card Ejecting the Card Reader Under Windows Before unplugging the card reader from your computer please use the unplug eject h
7. ras td 4 Under Matt E UI AAA AO ASA 4 Removing a Card Ejecting the Card Reader oooooconincnioccciccnnonnconncconocnno cono nonn coco nocnncnnnnno 4 Under WAOS a a aT iii 4 Undet MaG iinan niro n a AE AA e E caus coteesute lag 5 3 Using Windows ReadyBOOSt ccccccccccccccccccccccccccccconcnoncccnnnnncnnnnnnnnnnnnnenenennnnnns 6 LAOS a ae ee ae 9 As A 10 FONS a e edo 10 A O A A A aati 10 SV ETE Vane rive A a AS a a ses a a 10 1 Introduction 1 Introduction This USB 2 0 Single Slot Card Reader is a portable device that supports reading and writing Secure Digital Card SD and MultiMedia Card MMC series memory cards It s Plug and Play just plug it into a free USB port on your computer and it s ready to use Another benefit is that it supports the new generation high speed and high capacity memory cards e g SD version 2 0 and MMC version 4 2 ensuring you get the high performance brought by these memory cards What s best the card reader supports Windows ReadyBoost a feature allowing you to use a memory card to increase the available memory for Windows Vista You can use part of a card to enhance system performance and at the same time use the remaining part as a storage media letting you get the most out of one memory card Features E Supports SD and MMC series memory cards E Supports Windows ReadyBoot to enhance system performance needs ReadyBoost capable memory card not provided E Su
Download Pdf Manuals
Related Search