- DMS International
Contents
1. k N m V om E n oe Saati x LL mae M 2 as I 4442 1 2 4 Sov 8 H ANT IN Input from terrestrial To TV Output to TV S VIDEO S Video output S P DIF OPTICAL AC 3 output optical S P DIF COAXIAL AC 3 output coaxial AUDIO Audio output VIDEO Video output RS 232 Serial port to upgrade software 0 12V 0 12V DC output IF OUT IF output from LNB to other digital tuner IF IN IF input from LNB to digital tuner AC IN AC power input 50 60 2 30W POWER ON OFF Off 74 10 VE 12 ond 1 4 CT MBO 2C 21 oe a 10 11 12 13 14 15 16 17 18 19 21 You can power on off the receiver operate on screen menu and use va riety of hot key function POWER Is used to switch between the working mode or the standby mode EPG To display the electronic TV Radio program guide AUDIO To set the audio output mode and change the audio language INFO To display the current transmission information signal strength and quality PGUP To move the cursor up by a page in the menu or channel list SIGNAL To show the signal strength and quality of the current program VOL To adjust the volume level or change numbers or move left and right in the menu CH To cha2. After finishing hereinbefore sett ings press EXIT key to exit from this menu The following describes the basic functions of your STB while watching satellite TV or listening radio To increase or decrease the volume use VOL key either on the RCU when watching TV or listening radio When watching a channel the video from the current channel is frozen as soon as PAUSE is pressed Press PAUSE again to continue watching The STB provides EPG function for you to get access to the TV Guide that shows the necessary information of the current and future programs on different channels The information is only available from the network to which the channel you are watching Press green key you can setup the timer To see the EPG data press EPG key on your RCU when watching a channel The Program Guide window will be displayed You can see the channel list on the left side and program schedule for each channel next to the channel name The time related to the program sched ule for each channel next to the channel name The time related to the program schedule is also displayed Press OK key you will see detail of the EPG While watching the channel to switch between TV and radio modes by using TV RADIO key on the RCU eS If you searched channels from more than one satellite an
3. Rename The command allows you to modify satellite name se lected Rename command by using VOL key select a satellite by using CH key and press OK key you will see the sub menu as shown The operation for re name satellite is the same as Rename Channel gt Move After selecting this command a small input box will ap pear on the screen you need to input a number within the rang from 1 to the total number of the existing sa tellites by using numeric keys on the RCU After pres sing OK key the selected satellite will be moved to the new location specified by your input select Move command by using VOL key select a satellite you want by using CH key Press OK key im 7 78 ir iri Esso you will see the sub menu as shown Select Edit Transponder item on the Installation menu by using CH key and press OK key to display Edit Transponder menu As soon as a Satellite name is selected by using CH key in the left satellite list all the transponders which carried on the selected satellite are shown in the right list gt Satellite This command gives you the access to Edit Satellite menu Add The adding command allows you to add one or more tr ansponders for the selected satellite First Select a satellite by using CH key then select Add command by using VO
4. wall outlet Do not connect or modify cables when the reciver is plugged in Do not use a damaged power cord that may cause a fire or an electric shock Do not touch a power cord with wet hand It may cause an electric shock When connecting cables the receiver must have been powered off Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation Ensure that the ventilation is not impeded by covering the ventilation open ings with items such as newspapers table cloths curtains etc Do not place naked flame sources such as lighted candles on the apparatus Take attention to the environmental aspects of battery disposal Use the apparatus only in moderate climates not in tropical climates Do not expose the apparatus to dripping or splashing Do not place objects filled with liquids such as vases on the apparatus The location of the markings is at the bottom of the apparatus CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same of equivalent type Approval licence of CRT Instruction for installation or use in language acceptable to the country where the apparatus is intended to be used Current consumption is 150 mA du xt Brilliant On Screen Graphic MPEG 2 amp Fully DVB Compliant 2 Slot common interface for Viaccess Irdeto Cry ptoWorks Nagravision Conax SECA and more MPEG 2 Video MP ML MPEG 1 Audio Layerl Layer2
5. COMING TEE OT 2 3 9 Ot 5 ____ OV tem Se LUN a uia CMM 5 3 Sdec ____ E DEMME GOMMMMON IMENT ALS MEA Control cete utet T Generd View FUNCTION rai dae utat ui c Update seit dae eto qae due AD Vua 9 Trouble SHOOK A 19 GOSS Ol TOIT TIS TT Technical Spee meio espire catu eta ia evel du eese o dte et divus 12 28 28 29 29 30 30 32 33 33 33 33 33 34 34 34 34 34 35 36 38 41 43 11 12 13 14 15 16 17 18 19 Be sure to read this User s Manual before starting the operation of the receiver Do not open the cover It is dangerous to touch the inside of the receiver due to possible electric hazard Use a soft cloth and a mild solution of washing up liquid to clean the case When the reciver is unused for a long time unplug the power cord from the
6. and menus These menus will help you get the most from your Receiver guiding y ou through installation channel selection vewing and many other functions All functions can be carried out using the buttons on the remote control and some of the functions can also be carried out using the buttons on the front panel Please be aware that new software may change the functionality of the Receiver Should you experience any difficulties with the operation of your Receiver please consult the relevant section of this manual including the Problem Solving or alternatively call your dealer or a customer service requirement 8 a POWER Is used to switch between the working mode or the standby mode Display 4 Digit 7 Segment Displays the received channel while operating and time while in standby mode Remote Sensor Detects the infrared signals from the remote control unit VOL To change volume to move cursor change numbers in the menu or to change the choice MENU To enter into the main menu and exit all menus To change channel or move up and down within the menus OK To select an item in the menu and confirm it or pop up channel list Front Panel Display RF CHANNEL FLASH ROM ERROR ERROR STANDBY TIME TV RADIO MODE UPDATING IS FIN IS HE D LOADER MODE OPENING GREETINGS UPDATE WAITING RECEIVE DATA SIGNAL IS RECEIVED NO SIGNAL IS RECEIVED eS
7. 3 4 CH NTSC modulator DiSEqC1 2 positioner for multi satellites 63 satellites C Ku band control for each antenna User friendly and easy to use menu system Easy and fast software upgrade through RS 232 port LNB controlling logic 0 22KHz Tone SCPS MCPC receivable form C Ku band satellites Digital tuner with Loop through Wide symbol rate1 45Mbps amp frequency input 950 2150MHz DISEqC 1 2 supported User friendly OSD menu with full function 256 colors graphic user interface Multi language menu 8 digit 7 segment LED dis play Variable aspect ratio 4 3 16 9 with Pan Vector or Letter Box EPG Electronic Program Guide for on screen channel information Small screen picture on EPG Capacity for storing multi channel FTA 4000 channels 1500 trans ponders 8 favorite groups and Parental Lock function Pause and release picture Antenna positioning help feature SCPC MCPC receivable from C Ku band satellite Multi LNB controlled by DiSEqC1 2 and 22KHz S VIDEO output S PDIF Coaxial and optical AC 3 output Y Y YY Unpack the receiver and check to make sure that all of the following items are included in the packaging 1 x User s Manual 1 x Remote Control Unit RCU 1 x Digital Satellite Receiver 1 x Audio Video Cable Throughout this manual you will notice that the everyday operation of your Receiver is based on a series of user friendly on screen displays
8. DVB DBS 5500CI Owner s Manual TRAXIS Corporation Safety First Please review the following safety precautions If SS eee ae ee this is the first time you have useda receiver then read this manual before installing or using the A LE receiver If the receiver is not functioning properly please contact your local distributor or system installer lightning symbol in a triangle is used to alert you to the presence of dan gerous voltage inside the receiver that may be sufficient to constitute a risk of electric shock to anyone opening the case is also used to indicate improper installation or handling of the receiver that could damage the electrical system in the receiver or in other equipment attached to the receiver A The exclamation point in a triangle is used to alert you to important operating and maintenance instructions Failure to follow these instructions could re Sult in injury to you or damage to the receiver A Be careful with electricity Power outlet Power cord Power overloading Power plug Lightning Protect other equipment To prevent electric shock be sure the electrical plug used on the receiver s power cord matches the electrical outlet used to supply power to the receiver Connect the power cord only to a power source that operates at 100 240 Volts AC 50 60 Hz Be sure the power cord is routed so that it will not be stepped on or pinched
9. FTA gt CAS Free to air channels will be listed ahead of the scrambled channels Network All the programs will be arranged according to the satel lites sequence Transponder All the programs will be arranged according to the tran sponders sequence Favour gt No Favour Favourite channels will be listed ahead of the others Alphabet All the channels will be sorted in alphabetical order in other words sort the channels from A a Z z Select Radio channel by using CH key in Main Menu BEEN you will see the sub menu as shown The operation for the Radio Channels is the same as TV Channels while watching the channel to switch between TV and radio modes press TV RADIO on the RCU To increase or decrease the volume by using VOL key either on the RCU when watching TV or listening radio When watch ing a channel the video from the current channel is fro zen as soon as PAUSE key is pressed Press PAUSE key again to continue watching Select System Setting in Main Menu by using CH key press OK key you will see the sub menu as shown It has 6 items System OSD Select Time Zone gt Timer About STB Common Interface Select the item you want to operate by using CH key and press OK key to enter the corresponding sub menu This menu consists of the following items Menu Language System supports Engli
10. L key and press OK key to display the Add Transponder menu This menu lets you to set relevant parameters of the added transponder Please operate as per the following specification 1 Frequency First use CH key to highlight this item Use numeric on the RCU to input frequency After finis hing the input press OK key for comfirmation then you will exit from the edit mode 2 Polarisation Select the polarisation of the transpon der by using VOL key between HOR or VER 3 Symbol rate The operating methods are the same as Frequency 4 FEC Select the appropriate FEC from the preprogra mmed options including Auto 1 2 2 3 3 4 5 6 7 8 After the above parameters are set press OK key to return Edit Transponder menu Then you can see the parameters which are set by you in the right list Edit Select the transponder item you want to modify from the right list and use VOL key to select Edit command 5 The Edit Transponder window will appear on the screen after pressing OK key The operating methods are the same as Add command Delete This command allows you to delete the existing trans ponders of the selected satellite By using CH key select the unwanted transponder item from the right list then press VOL key to select Delete command Once OK key is pressed a dialog box which requires you to decide whether to delete the se lected item will appear on the screen Choose Y
11. The unil is iri sLardby mode The salel dish mul pelntlng 3st the satellite signal or weak signal The sata lite dish is Do nti d at satellite signalis 100 strong Satellite dish is small LNG noise high The LNE is faulty What To Do Check thatthe main cable i5 plugged inte thc power socket Press the standby bullon Ad ust le dish Check Siurial An enra setup Menu Check lhe cable tions LNE and other equipment connected between the LNB and the Ioccivor and or adjust the dish Adjust dish tL onnact a signal atte nuator to thie LAE input Lise large dish change LNE with Inwnr noise tantor Change the I Possible Cause Mo picture appears onthe sereon here sjnterference cr your digital satelli te channels The is not working The system 5 connec ted by SCART leads ar ROA and is not in AV EAIT mode The system Is connect ad using cable TF system 15 connected using RF leads and outaut channe ofthe recaiver interferes with anes Sling lerrestrial channelar Video signal Battery exhausted ROWS Incarrectiy aimed What To Do Ifthe system is conne cted by SGART leads ar RCA leads swihich lhe TV lu lhe appropi iate AV input UHF chanr el in your system and tune the c
12. a CA module will be needed to view such programmes Service provider Is a company theat collects a number of programms services and distributes them to customers SNR Signal to Noice Ratio Signal quality measure Symbol rate oize of the digital package transmis sion SW Software TS Transport stream VCR Video Cassette Recorder COMMON INTERFACE PCMCIA VIDEO Decoding Bit rate Output Aspect ratio Active pixel Output connector AUDIO Decoding Mode Bit rate Output connector DEMODULATOR Demodulation Symbol rate Outer code Inner code Energy dispersion INPUT SIGNAL Frequency Input level Channel bandwidth Input socked RF MODULATOR Input Output 2 Slot Type1 or Type2 DVB common Interface standard MPEG 2 amp MEPG 1 compatible Max 15Mbps PAL NTSC SECAM AUTO 4 3 16 9 Auto or 4 3 Pan 720x480 30fps 720x576 25fps RCA S VIDEO MPEG 2 MPEG 1 layer 4 Mono Dual Stereo Joint stereo Max 384K bps RCA S PDIF Optical QPSK SCP C MCPC RS 204 188 8 ALL DVB rates DVB S recommendation 950MHz 2150MHz 65dBm 25dBm 36M Hz F type connector F type connector F type connector Band TV Standard Output Channel LNB CONTROL Power supply Polarized control DiSEqC control MISCELLANEOUS Supply voltage Power consumption Operation temperature otorage temperature Dimension W xDx Weight VHF NTSC M 3 4 NTSC M 13 18V 500mA max pola
13. ator part of the LNB It converts from the satellite frequency down to a frequency acceptable for the Receiver MHz The prefix mega means million and Hertz means cycles per second MPEG Moving Picture Experts Group Body established by the International Standards Organisation to provde the basis for a picture coding and compression system Netw ork A number of digital channels trans mitted from one source Grouped under sepa rate headings in the channel list Parental control A feature that allows parents to Lock programmes that they consider unsui table for children A Locked channel or programme can only be unlock with the special parental access code PCR Program Clock Reference Polarization Polarization allows several programmes to be fit into the same frequency band The signals from a satellite are transmitted either with linear vertical or horizontal polar ization or circular right or left polarization RF Radio frequency known as HF in some countries SERIAL RS 232 A serial communication standard data port Satellite dish A dish shaped antenna reflector to receive signals from a satellite The dish focuses the signals into the LNB SCART 21 connector used for connection of the Receiver VCR TV Also named Euroconnector or Peritel connector Scrambled satellite TV programme Some satellite TV programmes are transmitted in scrambled form A Smartc ard and possibly
14. ay use thicker iron wires or other metal bar which upper part is connected with needlepoint and its underpart is connected with grounded object under ground the connection must use jointing Grounded down lead must use a whole wire and select the shortest distance to connect with grounded object Try your best not to make it bend Grounded object is metal object under ground which is usually made of steel tube angle iron and steel needle etc Its length should be 1 2m and depth should be more than 2m Grounded object of lightning rod can t be used by other grounded object at the same time It must be connected with ground alone 3 Metal pole lightning rod make and installation The lightning rod beanpole made of metal pole may use metal pole to lead mine electric current without any additional grounded down lead Lightning rod s needlepoint is connected with metal pole by weld Grounded object under ground can be made of steel tube angle iron and steel needle etc which length should be 1 2m The depth should be more than 2m and dust some salt in the pit 4 Higher lightning rod fits Bigger the protection area is When selected the setting place of lightning rod users should try their best to keep away from ways and entrances where people often pass by in order to prevent step voltage brought around lightning rod from harming people Lightning js daw u Tead Dcanpolc Lightnin
15. by heaw items Avoid overloading electrical outlets or extension cords which otherwise could result in electric shock or fire If a three prong power plug is provided with the receiver be sure it is used with a properly grounded three wire power socket For protection from lightning or when the receiver is left unat tended for a long period disconnect it from the power source Unplug the receiver before connecting any other equipment Power line especially the TV antenna connect all equipment to the re ceiver before plugging any power cords to the power source Be sure your TV antenna is not located near overhead power lines or where it might fall into any power lines Also be care ful to avoid touching any such power lines when installing the TV antenna A Also follow these precautions Ventilation Overheating Risk Of Fire Proper Connections Object Entry Water Expos ure Do not block the ventilation slots on the receiver or place any heaw object on top of it Blocking the air flow could damage the receiver Arrange com ponents so that air can flow freely around the receiver Ensure that there is adequate ventilation if the receiver is placed in a stand Put the receiver in a properly ventilated area away from direct sunlight or any source of heat Avoid stacking the receiver on top of a hot component such as a power amplifier Do not place the receiver on top of any easily combus
16. case you need to supply 22K tone to your LNB or antenna switch set 22KHz to be ON by using VOL key If the LNB frequency is set universal the 22KHz will operate automatically If there is signal under the selected satellite two dy namic bars at the bottom of the menu will reflect the sig nal strength and signal quality DiSEqC If DiSEqC box is DISEqC1 0 positioner should be set disable Since the STB is integrated with DiSEqC dumm j 1 2 it is possible to control an appropriate motor to driver multiple antennas Although you have entered correct val ues in Antenna setting menu if your antenna is positioned incorrectly you will not receive signal from the satellite 8 So the STB provides motorised setup in order to let you adjust the antenna more accurately to direct it toward a satellite Set Positioner to be Enable and press OKkey the Positioner setup menu will be displayed on the screen Position auto Select Position auto select the di rection by using VOL key During moving Press any key to stop if you want If find the signal it will stop automatically After finding the signal you can use Move steps to find the best position When you have the best position of the dish select Save position to save gt Continuously Move Please select this item and then keep pressing VOL key on the RCU to move your antenna east or west Use the signal strengt
17. d want to have a channel list for each satellite press ing SAT key for many times then the channel list of each satellite will be loop displayed Sometimes in order to watch TV clarity even more press ZOOM key the picture will be enlarged If a program is broadcast in more than one language the desired language can be selected directly by using AUDIO key on the RCU The AUDIO Setting menu lets you to select the appropriate audio language and audio mode VOL key can also be used to switch among the options The switching is made with the AUDIO button If the chan nels provider offers different Audio signals e g stereo amp then you can chose the mode in the Audo window Note This setting depends on the transmission of audio signal While watching the channel press INFO key on the RCU and not only does the channel name appear but also the satellite name as well as two dynamic bars reflecting signal strength and signal quality of the current channel Exit all menus press OK key you can see all TV progrmas Update Software receiver to receiver 1 Connect master and slave receivers with twisted RS 232C cable Power on the master receiver and make it in standby mode After start successfully turn on slave receiver to begin update he panel of master receiver will display H and blink it Input the password 123 by remote control to update the software After update it will
18. display and on each panel Turn off slave receiver disconnect twisted RS 232C cable and restart it Jo C Notes Input the password 123 to update the software Input the password 456 to update the data Input the password 789 to update the software and data Input the password 369 to copy the whole flash Update Software Computer to receiver 1 Connect your PC and receiver with twisted RS 232C cable 2 Turn on the receiver and make it in standby mode 3 Startup the software STB5518 exe on your PC press Select key select bin then select port Press start on your PC Upgrade will begin 4 After upgrade the receiver will display End on panel 5 Turn off the receiver disconnect twisted RS 232C Cable and restart it Notes You need a 9 pin twisted RS 232C cable pin 2 to pin 3 pin 3 to pin 2 pin 5 to pin 5 You can not turn off the slave receiver until it display End and OK on the panel Important note Due to new modification of flash to 16M you need to press POWER button to make receiver in standby mode before you update the software from computer or receiver master receiver only The display on front panel does nat light up sour d or picture iulilis ui sound nr Bad pictura blocking errar Main cable is nat conn ected
19. ect one channel from the channel list then select the second icon and press OK key a password is required the default value is 0000 then the selected channel will be marked with Please note that you can t view the locked channel unless you input a right password gt Delete Channel This command allows you delete one or more channels permanently First select the unwanted channel item then use VOL key to select the third icon symbol will appear on the selected channel item after pressing OK key Note The deleted channel can t be watched unless you search it again Move Channel After selecting this command a small input box will ap pear on the screen You need to input a number within the range from 1 to the total number of the existing chan nels by using numeric key onthe RCU After pressing OK key the selected channel will be moved to the new location specified by your input Rename Channel Select the channel whose name needs to be modified as you like then selected Rename icon and press OK key a keypad dialog consisting of a title bar a alphabet and five function will appear on the screen Caps on Switch capital and lowercase Back Delete character one by one Cancel Delete all characters Select character by using CH VOL or OK key to rename channel Press OK command to confirm it Modify Channel the selected channel First select one channel from the This com
20. es and press OK key to delete else cancel the operation This menu consists of the All Channel List and Load Default Data Use CH key to select one item and press OK key to enter the corresponding sub menu Select All all your settings and stored data are deleted The receiver is reset to original settings Select Channel list your personal channel list is deleted Select Load Default Data if you have deleted a perso nal channel list you must load company settings of the channel list using Load default settings subsequently Select TV Channels in Main Menu by using CH key press OK key you will see the sub menu as shown It has 3 items Edit Channels Set Favourites Sort Channels This menu gives you access to options which allow you to edit channels set favourites and sort channels Move cursor to the desired option by using CH key and press OK key to enter the corresponding sub menu I In the lower right corner of the Edit Channels menu you can see a series of icons and a title bar showing the mean ing to the highlighted icon First press CH key to select MEN channel from the channel list at the left side of the Pre menu then select some icon by using VOL key and Dress OK key to execute the corresponding command Play Channel You can watch the selected channel in Graphic PlG mode via the window at the left side of the menu Lock Channel First sel
21. f the searched transponder When searching is finished the Antenna Setting menu will appear instead of the Searching New Channels window The searched channels will be added to the channel list displayed by using OK key at the non menu mode You should set the various parameter values beforehand Two dynamic bars at the bottom of the window reflect pE the signal strength and signal quality of the current parameters Select Manual Search by using CH key press OK key you will see the sub menu as shown Sat name Select the name of the satellite by using key which needs to be searched Freque ncy Select a valid transponder in the satellite or input the frequency 0 20000 MHz Polarisation Select the polarisation of transponder be tween HOR and VER by using VOL key Symbol rate Press numeric keys to enter your required value manually Input the correct symbol rate 0 45000 FEC Forward Error Correction Select the FEC of transponder by using VOL key Available option are Auto 1 2 2 3 3 4 5 6 and 7 8 Network search Select YES Search some new chan nels from some transponders Select NO Only search the transponder channels FTA Only Only Yes Searchonly free to air channels FTA Only No Search all channels Advanced Manual PID entry are possible here Press ing OK key on the RCU will display Advanced Search menu Use CH key to activate the PID item you want t
22. g rod s protection area Ticampale lighiting red sketch map Table of Contents WMSMUCIONS oL General Feat S WFNS AG ICING General MAU ON o eek RO Bis sid gez E e Remote MR RM E Installation of Connecting to Antenna and Connecting to TV using RCA 5 Connecting to TV using S VHS Connecting to TV using RF supportt Connecting to another Connecting DiSEqC switch Connecting to TV using S PDIF COAXIAL Support va col ee RR nua rum DU T T 2 1 22 MAU SE ceat e Rud CUP 2 9 Edito 2 4 as ene 2 9 WC AUN 66 TN Sel 21 ROUTE M ECL
23. h and sig nal quality bars at the bottom of the screen to judge the best position of the antenna Step Size The setting range is from 1 to 10 Use VOL key to switch among them gt Move Steps Use VOL key to select the required move steps gt Limit Set Use this item to set the East and West limits of the motor This should be used to prevent your dish from hitting anything that may obstruct the path of the dish Highight this item and press VOL key to move your motor east or west limit then press OK key on the RCU to save To setthe West Limit followthe same steps as East Limit Warning If this item is disabled your motor will be able to move beyond any limits Please take care incase there are anything obstructing the path of your dish Save position Save the position of the satellite Goto position Press OK key the motor will return to the last position of the satellite to reference The motorised system of factory FTA Only Only Yes Search only free to air channels Only No Search all channels Start search Select Start search by using CH key Select Sat Network TP by using VOL key Select Sat search satellite channels Select Network search some new channels from some transponders Select TP search transponder channels Once OK key is pressed Searching New Channels win dow will appear the screen During searching y ou can see the parameter information o
24. hannel Charge receiver nut put zaanragltn more si channzl or sging ct the system using SCA RT leads Change the battery Aim the GU at the unit or check that blacks lhe front Access Authorisation to use the coding system to purchase order TV programmes AGC Automatic Gain Control Audio system with digital satellite reception the soundis transmitted in packages and is selected either in a special audio mode or pre selected by using the installation set up This makes it possible to select between several different languages in a film The number of choices is dependent on what is available in the signal DVB The Digital Video Broadcast group was created to establish a technical frame work for the introduction of digital video broadcasting systems EPG Electronic Programme Guide A software that enables viewers to navigate easily among the large number of channels provided by digital technology in order to select the service they desire FEC Forward Error Correction Correction of faulty bits in the received signal GHz The prefix giga means billion and Hertz means cycles per second Signals in the GHz range are often called microwaves LNB low noise block converter or LNBF An electronic unit mounted on the satellite dish It receives the signals reflected by the dish and converts them to signals that can be used by the Receiver L O Local oscill
25. llows you to search up to four satellites at one time If you want to search the selected satellite set the cor responding status to be ON by using VOL key Satellite name Select one item in the first column by using CH key and press VOL key to pop up a list box which lets you to select the desired satellite name Use CH key to select and press OK key to confirm Please make sure that the antenna of the selected sat ellite has been connected to one of LNB s input ports DiSEqC Press VOL key to select the proper LNB s in put port according to your satellite antenna connection LNB Frequency ALL of the standard typical local oscil lation frequency values are user spendable Press VOL key to select the desired one If Universal is selected both 9750 and 10600MHz are supported at the same time gt Fast Tuning Auto Tuning After the above mentioned ones are set correctly Se lect Fast Tuning search all channels Select Auto Tuning search not only all channels but also it can download new channels the searching speed is slower than Fast Tuning press OK key then the message FTA channels only wil be displayed So one decision needs to be made before proceeding to search lf YES is selected only free to air channels can be searched Otherwise system will search all the channels Once you make a decision Searching new channels win dow will display on the screen If more than one satelli
26. m Need Screen Edit H Rename Wove f Edi Satellite Add Edi De ete Laat Aula Turning T Rad e Channels alti 2 3 Favauri as 5 oPanhe s Flay Leck 1 Wave Modify Favourites 2 F vE W FAME FAV FAV4 FAVE Sort Channels 5 Trarsponder gt Favour Alphabet ro Se
27. mand allows you to modify the PID values of Emm channel list then select the last icon and press OK key to display Modify Channel window Modify various PID values as per the following steps 1 Move cursor to highlight the item you want to modify by using CH key 2 Select Modify command by using VOL key 3 Use numeric key to input 4 After the whole PID value is set press OK key for confirmation then you will exit from the edit mode 5 Move cursor to next item by using CH key In Set Favourites menu popular programs be added to one of eight different favourite lists labeled them FAV 1 FAV2 FAV3 FAV4 FAV5 FAV6 FAV7 8 gt FAV1 First use VOL key to select the name of the favourite groups FAV1 press green key you can rename favourite group Move cursor to highlight your favourite channel and press OK key the selected channel will be marked with To cancel your selection press OK key again After finished exit all menus press FAV you will see favourite channels of FAV1 group The operation for the FAV2 FAV3 FAV4 FAV5 FAV6 and FAV8 are the same as FAV f This feature allows you to sort channels as you like In Sort Channels menu select the sort order you want by using CH key and press OK key toconfirm Meanwhile Edit Channel window where all the channels are arranged according to your choice appears on the screen gt
28. nd Delete field by using Ware VOL key depending on whether you want to carry out timer setting First select you wanted to add channel press VOL key to switch channel press OK key to confirm it input Data Start Stop Rpt and Source with CH VOL and numeric keys then input the de sired values using numerical keys press OK key to con firm the timer setting the timer setting is displayed The new timer setting is included in the list Carry out further timer settings if you wish to do so Press EXIT key to exit the menu Notes Select Rpt by using CH press VOL to switch it It has 5 kinds instance Miu 2 T Conn 1x Repeat once per day D Repeat on the set day 1W Repeat once from monday to Sunday 1 5 Repeat once on each day from Monday to Friday 6 7 Repeat once on each day from Saturday to Sunday From here you get not only the information about the hardware and the software but also the manufacture name 1 Preparing To be able to receive scrambled digital satellite chan nels you need a Smartcard and a Common Interface CA Conditional Access module from the Service Prowder of your choice The Smartcard and the PCMCIA module may also pro vide access to special menus not described in this manual If so please follow the instructions from the Service Provider Only free to air channels are available without the Smartcard and PCMCIA Module In
29. nect the TV antenna to the ANT IN on the Receiver I OAT i al YCR rr a BUT TO E RE Pore TM TV antenna FRU AH LI M p 14 2 li A vara 1 gt 2 TYL I kx i iM re i T 5 u mms onde 2 m ut TV antenna s Id FROH vn ry cn CUT TE 7 SWITCH KATA af TUPIER d a 2o pg 1 om i Li Ae vl I gt 4 1 DVB ZUM ire LEE CP 1 Termin m n Le n 1 res Once you have installed and connected the cables the menu will be displayed This menu consists of 6 main menus as shown below Easy Tuning gt Installation TV Channels Radio Channels System Setting Parental Control During the Installation the OK key confirms a selection Use the CH key to move up or down from one line to another line To escape the menu system at anytime press EXIT key on the RCU LLL m With its DiSEqC1 0 the STB can drive four individual LNB s So this feature a
30. nge channels in viewing mode or move the cursor up down in menu mode MENU To display the main menu in viewing mode and the TV radio program screen in menu mode ZOOM To enlarge the picture SAT To select satellite channel list NUMERIC KEY 0 9 To control the numerical operation and especially change the program channel selection directly FAV To switch between the selected favorite channels MUTE Turns the sound output on off TV RADIO To switche between TV and radio programs PAUSE To select or de select picture freeze RECALL To return to the previously selected channel PGDW To move the cursor down by a page in the menu or channel list OK To select an item in the menu and confirm it or pop up channel list EXIT To exit from the menu or other onscreen displays FAV To display the current favorite channel list or to view general informa tion see favorite channel list for more details This section explains the installation of Receiver Refer to the manuals supplied with the equipment for the installation of outdoor equipment such as the dish antenna When adding new equipment be sure to refer to the related parts of the manual for the installation 1 Refer to your video recorder manual for full instructions 2 Connect one SCART cable between the main SCART socket onthe TV and the TV SCART socket on the Receiver 3 Camectthe cabb from the REF outpubcn the VCR to the FF on the TV 4 Con
31. o modify and input the appropriate value by using num eric keys on the RCU After finishing the input press OK key to confirm or press EXIT key to return Manual Search menu 23 Edit Satellite This menu consists of two parts the upper part showing a list of the satellite name and the lower part listing four command options which are used to add delete rename and move the satellite shown in the upper list To scroll the displayed satellite name move the scroll bar on right edge ofthe list box by using CH key or PGUP PGDW key Select some command options and press OK to execute the corresponding command Select Edit Satellite command by using CH key press OK key you will see the sub menu as shown Add If your required satellite isn t listed the adding command enables you to add the new satellite to the list Select Add by using amp key and press OK key the screen will display After you input data press OK key then a new satellite item will be displayed next to the last satellite item you should rename it by using Re name command explained below gt Delete This command allows you to delete one or more satellites from the satellite list Select Delete by using VOL key select a satellite you want to delete by using CH key or PGUP PGDW key Press OK key you will see the sub menu If select Yes by using VOL key press OK key then delete the satellite else cancel operation
32. rization with short circuit protection 13 18V polarization vertical horizontal DiSEqC 1 0 and DiSEqC 1 2 100 240VAC 50 60Hz 30 watts max 5 C to 40 20 C to 70 280 207x55 mm 2 3Kg wal Search aat Frequency sation Antenna Trarapander trary ene y SEM svmbal rate JiSEqC EEG only Start search Advarced actary 1 41 2 L st Alaad Itala Insiallatios Altea na Setting 2 Manual 3 L dit Satell re 4 Edil a Facte y Default Fare ork Edit Chanasl Lack nzx Charge d Easy Tuning Insralla Isn Channels Me nu oo 1 vr Bue About Channals piis Settin n ifaeture SET a Corio id Flag Company Loader 387 em T Adel Edit re 3 SaleclT rne Zorna 4 a 9 4bout 8 Zenon like 1 Time Zane MT Curent time ae c am p rene T Lang ge Color A adio Language Syete
33. sert the PCMCIA Module in the slot of Receiver and insert the Smartcard to the PCMCIA module This will give you access to scrambled channels Note Receiver has 2 slots for PCMCIA Module 2 Check Manager Select Common Interface menu in the Main Menu page Then Receiver detects and shows the PCMCIA Module names which you have inserted in the slots Then select slot1 or slot2 You will then see the information provided by the Pro gram provider Note This information may be different for each Pro gram Provider D 23g The STB provides an active parental lock function al lowing you to block specific menu setting by means of a four digit security code Accessing the parental Control menu is controlled by a password The default value is 0000 If necessary you can change Highlight the item you want to operate and press VOL key to select YES or NO A password is required for the menu which its corresponding item has been set to YES For example if you set Installation Lock to be YES the Installation menu is accessible only when a password is entered The password is 0000 You can change it as per the following steps 1 Set Change Password to be YES by using VOL key 2 To enter the new password in the input box of Input New Password press numeric keys on the RCU directly 3 Enter the new password again in the input box of Confirm Password
34. sh German French Spanish Portugal and Italian Press VOL key to select the desired language for menu Audio Language Select the first language to listen if this language is supported by current program This de pends on the trans mission of audio signal RF Channel In case your TV is connect through RF modulator VHF select output channel number you want RF System NTSC M TV System Select your TV type between PAL NTSC and SECAM by using VOL key TV Screen Format Select your TV aspect ratio of output video either 4 3 16 9 Auto or 4 3 pan by using VOL key EE Menu Color Select your favourite color of menu by us ing VOL key Transparency You can adjust the transparency of the menu from 1 to 10 by using VOL key Need Help As soon as YES is selected usable keys and relevant specification are displayed at the bottom of the menu 5 3 Select Time Zone _ In order to display the local time correctly it may be nec essary to set a time offset indicating the difference be tween local time and GMT press VOL key to select your required from the preprogrammed options The timer automatically turns on the receiver for certain favour channel and adjusts the desired channel Here you can control the records for different datas and from different channels Add you wanted channel to set timer select Timer in System Setting menu press OK key a timer list is displayed Add Edit a
35. te are set to be ON then each satellite will be searched one after the other During searching the searched chan nels are automatically sorted into two category TV and Radio Two dynamic bars at the bottom of the window reflect the signal strength and signal quality If you want to stop searching please press EXIT key during this procedure New searched channels will be added to channel list displayed by pressing OK key at the no menu mode automatic ally Select Installation in Main Menu by using CH key press OK key you will see the sub menu as shown It has 5 items Antenna Setting Manual Search Edit Satellite Edit Transponder Factory Default Select the item you want to operate by using CH key and press OK key to enter the corresponding sub menu Y WF Y You should set the appropriate parameter values with which you can search channels here Sat name Select the name of the satellite by using key which needs to be searched Transponder Switch among all the trans ponders car ried on the satellite shown in the first item LNB frequency All of the standard typical local oscil lator frequencies are available and any unusual values can simply be manually entered Select the desired one from the preprogrammed options by using VOL key or use numeric keys on the RCU to enter y our required LNB frequency If Universal is selected both 9750 and 10600 MHz are supported at the same time 22KHz In
36. tible material such as carpet or fabric Be sure all cables and equipment are connected to the re ceiver as described in this manual To avoid electric shock never stick anything in the slots on the case or remove the cover To reduce the risk of fire or electric shock do not expose the receiver to rain or moisture The Way Of Prevent Satellite Receiving Antenna From Hitting By Mine Satellite receiving antenna is fit on where is higher which is easily hit by mine Mine not only destroys the device but also makes a menace to people s safety So it is very important to fit on lightning rod on antenna 1 The protection area of lightning rod The protection area of lightning rod is 45 60 pie slice area under lightning rod The antenna will be protected when it is in the pie slice area Higher the lightning rod fit Bigger the protection area is Antenna must be fit in the pro tection area The distance between lightning rod and protected antenna should be more than om because the faradism of lightning rod and its down lead hit by mine pen etrate 2 3m air 2 Wood pole lightning rod make and installation Lightning rod is made up of lightning rod s needlepoint beanpole grounded down lead and grounded object The second image is wool pole beanpole lightning rod Needlepoint is made of thicker brass wires and iron wires The thick iron stick is better Beanpole may use wood pole or metal pole Grounded down lead m
Download Pdf Manuals
Related Search