XD-16 Digital Universal Dash Display User Manual
Contents
1. 6 Firmware for the XD 16 has the extension did You can also download the latest firmware and software LM Programmer and Demo from the Innovate Motorsports web site at http www tuneyourengine com IF your computer crashes during a firmware upgrade the XD 16 has a recovery mechanism where it will be able to retry the download again and not be disabled by half loaded firmware Switch the XD 16 off and on again and then try to restart the LM Manager software The recovery mechanism is designed to be able to recover 99 9 of the time While we don t anticipate this occurring it is possible that the XD 16 will not recover correctly and may need to be serviced at our factory If you suspect this is the case contact Innovate support 5 5 Selecting the display channel Click on the Input Tab at the top of the window The following screen will appear Der LM Programmer Version 3 00 x Info Log Connection Input Min Hold Max Hold Alarm Colors Select Input to be displayed LM 1_airfuel Input Info Display AFR C Display Lambda Limit outside LED indicated range to 10 0 ta 13 4 AFR Lettmost LED Rightmost LED You can select the input channel to display whether Lambda or AFR is displayed when selecting a wideband Lambda AFR channel and also you can set the range of the analog needle LEDs Press the program button when you are finished If you select something other than a Lambda AFR channel you wi2. TUNER TOOLS LOM g INNOVATE auth ized MOTORSPORTS reseller XD 16 Digital Universal Dash Display User Manual XD 16 Manual_1 3 doc 1 VENEN Eee ee see 3 2 The XD 16 Device The XD 16 Module 2 1 Identifying the user interface features of the XD 16 u0022220002200000000nno nennen nennen nnnnnnnnnnnnnnnnnnnnnnnnen 4 2 2 Inel ded eaplesand devices a ana sireieske 4 3 Mounting and Connecting the XD 16 irainen a a a ae a a a E 4 4 UTS WAG STNG A DETG mni a E ted Saeeeenes 5 4 1 Displayed functions when using XD 16 as AFR Lambda display cccccsssceccsseeeeeseeeeeeeeseeeeaeeessaaeeees 5 AA BUOM FUNCIONS Seesen Meiner a a tenes 6 5 Programming ino AT a ee ee aS 7 5 1 Installing the LM Programmer Softwar e cccccccssssccccccsseeeeecceeecececseeeceeeseaeeeesseaaeeeesssagecesessageeeeeeessaaess 7 5 2 Setting up the used inputs in LogWorks cccccccsseseseeceeceeeeeeseceeeeeeeaeeeseeceeeesesaaeseeeeeeessuaaaseeeeeeeeeessaaaaenes 7 5 3 Connecting the XD 16 device to the computer sss22224000000Rnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnne nennen 7 5 4 Updating the IFIRAW ANC cies set en ee seen re 8 5 5 Seleclng the display channels een eranhe 9 5 6 Programming the Min Max hold functions 2222220002000000000000nnnnnn nennen nnnnnnnnnnnnnnnnnnnnnnnnnnne nennen 10 5 7 Programming the Warning Alarm function u00444400BRenn
3. air 5 Switching between cud and od Shows the free air content of the gas the sensor sees 5 No Connection detected If the display shows men The XD 16 cannot receive data from the LM 1 or other devices Check the cables 4 2 Button Functions 1 Start Stop Recording Press the Control button once to start recording The Record indicator light will blink Press the Control button again once to stop recording The Record indictor will switch off 2 Clear Recording Memory of LM 1 Press and hold the Control button until rES for Reset shows 3 Review Min Max hold Press the Control button twice rapidly The XD 16 will show the last minimum value indicated Note that the XD 16 will remember the minimum value even if power is switched off Minimum value is indicated by alternating between Lo and the minimum value stored Holding the Control button down for a few seconds while this is displayed will reset the minimum value Press the Control button instead only briefly will show the maximum value indicated It is indicated by alternating between Hi and the maximum value stored Press the Control button again briefly to return to normal operation Holding the Control button down for a few seconds while this is displayed will reset the maximum value 3 Initiating a free air calibration Press the Control button three times rapidly The display will show a blinking If the button was press accidentally three times wai
4. annel input 3 This manual XD 16 Manual 4 The LogWorks Manual Describes how to use LogWorks for datalogging and engine analysis 5 The RPM converter LMA 2 Manual Describes how to operate and use the LMA 2 RPM converter and how to connect different engine sensors Used for LM 1 users 6 The current firmware for the XD 16 7 Anexample datalog file 5 2 Setting up the used inputs in LogWorks Make sure the input channels to be used by the XD 16 are correctly programmed in LogWorks as they would show up on the LogWorks screen Refer to the LogWorks manual for details When programming the XD 16 the current real time settings of LogWorks are used to program the XD 16 5 3 Connecting the XD 16 device to the computer 1 Connect the Serial OUT connection with the included 2 5mm stereo to DB 9 cable to a serial port on your laptop 2 Connect the terminator plug 2 5mm male plug with no cable into the Serial IN connection of the XD 16 Start the LM Programmer software The screen should look like this oe LM Programmer Version 3 00 ll x Info Log Connection Input Min Hold Max Hold Alam Colors 2003 2004 Innovate Technology Inc INNOVATE iMoOTORS Poa Ts Device Type Serial Display XD1 Firmware Version 1 00a Connected to port COM 2 Processor Version ATM16 6 5 4 Updating the Firmware Click the Update Firmware in the main page to upgrade to the latest firmware for the XD 1
5. ble between the Serial OUT port of the XD 16 and the computer s serial port The following diagram show how to connect multiple Innovate Motorsports devices to form a logging and display chain The example chain consists of a LM 1 a LC 1 a LMA 3 and 2 XD 16 s In this case the chain has 12 channels 6 from LM 1 1 from LC 1 and 5 from LMA 3 To Computer 4 Using the XD 16 When the XD 16 powers up it will go briefly through a sequence where it lights up all its LEDs This is a function and diagnostic test Holding down the Control button during power up will continue to light up all LEDs until the button is released 4 1 Displayed functions when using XD 16 as AFR Lambda display 1 Sensor Warm up For example this would indicate that he heater is warmed up to 56 The Function Indicator 2 is lit 2 Heater Calibration The last digit is the count down of the heater calibration 3 Free air calibration in process When shown steady free air calibration is in progress If blinking and not going away after 5 seconds the LM 1 requests a free air calibration as happens after a heater calibration Blinking CAL can also happen if the control button is pressed rapidly 3 times Pressing it then again initiates a free air calibration If this is unintentionally pressed the CAL request goes away after 5 seconds 4 Normal Operation With function indicator 1 lit this shows AFR 5 Normal Operation very lean mixture or free
6. g as described in 4 6 Except here the Alarm condition can be programmed to be dependent on two other channels and time During an Alarm the XD 16 will flash the indicated value and the analog needle LEDs at maximum brightness until the Alarm condition goes away 12 5 8 Programming the Analog needle colors Click on the Colors tab a LM Programmer Version 3 00 oj x Log Connection Input Min Hold Max Hold Aam Colors Min Hald Max Hold Indicator color BU E a LQ indicator color u gt 13 8 15 6 16 1 128 16 6 Double 123 17 0 ui a ae Br 75 other LED change E iii 18 0 8 set tto ine Same color 109 18 4 oz Ovo ez KR Factory default colors Sweep Test This shows the current color settings for all the 21 LEDs plus the indicator colors used when reviewing Min Max hold To change the color of an individual LED double click with your mouse on the LED to change The following dialog box will show up Set Color The currently selected LED is also highlighted By changing the sliders for red green and blue any color out of a set of 32767 colors can be created Any color can be created by mixing red green and blue light at varying ratios The XD 16 can be programmed for 32 different values for each red green and blue And 32x32x32 is 32768 But black all off is hardly used While moving the sliders the simulated LED on the screen changes colo
7. hole of the bezel with the screw hole of the back plate ensuring that everything slides into the bezel correctly Holding the assembly together with one hand test the operation of the button and as necessary adjust by rotating bezel glass and gauge face Reinstall the 3 Phillips screws 14 6 2 Create a custom label Note To customize you will need to use a blank white gauge face supplied with every XD 16 Innovate Motorsports will provide downloadable pdf file templates for the most common sensors at www innovatemotorsports com Print these templates on clear overhead foil suitable for your printer Any stationary store carries those Depending whether you use an inkjet or laser printer different foils will be needed Exacto knife or razor blade or scissors Piece of plywood or sturdy cardboard as cutting background Do not use the kitchen table A 1 8 hole punch Leather equipment stores or horse tack stores carry those A small Phillips screw driver Blank white XD 16 face included S aloe ea 6 3 Assembly sequence of the XD 16 with foil face D w Bezel Electronics Package Front Control and back plate Glass Blank button Printed face foil face Appendix A Specifications Supply voltage range 8V to 25V Current draw lt 600 mA Weight 302 82g Serial port speed 19 2 kb Max serial port cable length 15 ft Current draw depends on outside brightness and number of LED segment
8. ill blink when a LM 1 or other Innovate Motorsports recording product is attached and actively recording 2 2 Included cables and devices 1 XD 16 to LM 1 cable Mini DIN 8 to female 2 5mm Stereo Use with patch cable 3 below 2 XD 16 to Computer cable male 2 5mm Stereo to DB 9 3 Male 2 5mm Stereo to male 2 5mm Stereo cable 4 XD 16 Terminator plug single male 2 5mm Stereo plug 5 XD 16 Mounting bracket studs and nuts 6 CD with manual and programming software 3 Mounting and Connecting the XD 16 1 If not using a commercial gauge pod cut a 52mm hole into the intended dash location 2 Insert and mount the XD 16 and mount it with the included mounting bracket leaving the XD 16 cables in the back accessible 3 Connect the RED wire from the back of the XD 16 to a switched 12V source in your car A switched 12V source goes on as soon as the ignition on the car is on or the engine runs Make sure the connection is fused with at least a 2A fuse 4 If connecting to a LM 1 connect the XD 16 to LM 1 cable to the LM 1 s Serial Port Plug the 2 5mm male stereo end into the XD 16 Serial IN port female 2 5 mm socket marked IN 5 If connecting to an LC 1 or LMA 3 connect the male 2 5mm Stereo to male 2 5mm Stereo cable between the Serial OUT port of the LC 1 or the Serial OUT of the LMA 3 to the Serial IN port of the XD 16 6 If using a computer to datalog or download LM 1 data connect the XD 16 to Computer ca
9. ll first need to connect all your MTS devices or LM 1 to LogWorks and complete a real time log LogWorks compiles channel information through this process Exit LogWorks and reconnect to LM Programmer The list of available devices channels will be now be selectable from the Input tab If you select something other than a Lambda AFR channel the display will change to Fi n LM Programmer Version 3 00 oO x Info Log Connection Input Min Hold Max Hold Alarm Colors Select Input to be displayed E PM Input Info Range Oto 10230 RPM Will be displayed as Oto 102 x100 RPM Limit displayed range to fo to 10230 RPM Apply Limit Limit outside LED indicated range to to frz RPM Leftmast LED Rightmost LED As you can see here the display will indicate in 100 RPM This might be too coarse for many applications The limit is there because the XD 16 can only display 3 digits By applying a limit for example to 0 9990 RPM the XD 16 can display the RPM in multiples of 10 RPM Ifa channel is selected that has both positive and negative values a different screen will show rie LM Programmer Version 3 00 el x Info Log Connection Input Min Hold Max Hold Alarm Colors Input Info select Input to be displayed Range 2 00 to 2 00 g Will be displayed as 2 0 to 2 00 g Limit displayed range to po to Poo a Apply Lin E Use left top LED as negative indicator instead of in dis
10. nnnnnnnnnnnnnnn nennen nnennnn nennen nennen nnennnn nennen 11 5 8 Programming the Analog needle colors ccccsssseccccceesseeeeccaeeeeceeccaeeececeseaeeceesssaaseeeessaageeeeesaueeeeeeeeaas 12 6 Changing the gauge face of the XD 16 222222u0002000000000nnnnnnonnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnn 13 Gite stalling ThE NEW gauge Taco sinne ee nennen re 13 62 GREATS a CUSTOM TAS sesan cciact hot adieaecicige ee eng 14 6 3 Assembly sequence of the XD 16 with foil fACC ce ecccccsseececeeeeeeeeeeeeesseeeeeseeeeeeseaaeeesseeeessageeessneeeeens 14 ADDEnd A 3 DC CINICAOING en ae ee lee 14 FC VISION MASON y era ott ee ee ee nee 15 1 Overview The XD 16 is a programmable digital display used as dash mounted instrument for the Innovate Motorsports sensor devices The XD 16 fits into a standard 52mm 2 1 16 gauge hole Multiple XD 16 s can be daisy chained to build and entire programmable dash XD 16 gauge faces can be user customized The XD 16 can also be used to initiate and control recording on the LM 1 or other Innovate Recording devices can initiate free air calibration for Innovate Motorsports wideband controllers and indicate wideband controller status In addition the XD 16 can be programmed to hold minimum maximum values of the displayed channel and provide warnings alerts depending on programmable warn conditions 2 The XD 16 Device The XD 16 set contains the follo
11. play fight LED indicates positive value mit outside LED indicated range to 2 00 to 2 00 g Leftmost LED Rightmost LED This allows you to use the Indicator 1 and 2 LEDs as negative value indicators to preserve the 3 digit resolution of the XD 16 5 6 Programming the Min Max hold functions Click on the Min Hold or Max Hold Tab on the top of the window The following screen will show up 10 LM Programmer Version 3 00 I x Info Log Connection Input Min Hold Max Hold Alarm Colors W Enable Function Hold only if Throttle jsmorethan 77 is less than feo k for at least foa Seconds max 10 Seconds Programming the Min or Max hold function should be pretty self evident You can enable the function You can also make the hold function depending on another channel In this example the Max hold function will be programmed so that the leanest AFR is only stored during WOT operation and only if the condition persists for more than 0 2 seconds In this case AFR was used as input and you don t want to store the leanest AFR during closed throttle where the injectors cut off Any channel can be programmed as dependency You can program any minimum persist time between 0 and 10 seconds 5 7 Programming the Warning Alarm function Click on the Alarm tab on the top of the screen oe es LM Programmer Version 3 00 Again the programming is very similar to the Min Max hold programmin
12. r and also the appropriate LED on the XD 16 at the same time Because computer screens use a different technology to create colors than the XD 16 the actual colors on the XD 16 can be different than the screen colors With the sweep test button the XD 16 will sweep through all LEDs from left to right to give you and indication on how the color scheme you programmed will look in real life To change multiple LEDs to the same color just program one LED Then drag this LED over the other LEDs you want to program to the same color 19 2 6 Changing the gauge face of the XD 16 When you use the XD 16 to display different channels than AFR or Lambda you very likely want to change the gauge face As the LM 1 MTS system can be programmed for any 0 5V sensor the possibilities are endless Because not every possible use can be anticipated the XD 16 is designed to allow user customization 6 1 Installing the new gauge face 1 Lay the XD 16 face down on a table and remove the three Phillips screws from the outside rim of the back plate Carefully lift out the back plate with the electronics package from the bezel Laying the electronics package on its back first place the gauge face followed the glass and bezel Be sure to remove protective film from the gauge face This can be done easily with a piece of scotch tape Make sure every piece is positioned correctly on the button shaft Carefully flip the complete assembly and line up the screw
13. s lit 15 Revision History 1 0 2 5 05 Initial release 1 1 3 16 05 Corrected misc errata 1 2 4 11 05 Corrected section 2 2 1 3 2 06 06 Added XD 16 information 16
14. t for 5 seconds The XD 16 will return to normal display mode 6 Pressing the Control button while the blinking CAL is displayed will initiate a free air calibration on ALL connected wideband devices 5 Programming the XD 16 You will need 1 XD 16 to Computer cable male 2 5mm Stereo to DB 9 2 XD 16 Terminator plug single male 2 5mm Stereo plug 3 A laptop computer 4 When powered by the car the ignition of the car must be on to power the XD 16 Alternatively you can power the XD 16 with a suitable power source between 8V and 25V A normal 9V battery can be used to power the XD 16 5 1 Installing the LM Programmer Software Put the included CD in your CD drive on your computer and follow the instructions on screen The Software will be installed including pre set directories for log data and downloaded software The LM Installer also puts entries for the LM Software in the Start Menu of your computer under the heading Innovate The following items will be installed on your hard drive 1 LM Programmer Version 3 0 This is used to program the XD 16 2 LogWorks This is a comprehensive datalogging and analysis package to download and analyze engine data recorded with Innovate devices It also allows real time logging and display LogWorks allows to program the relationship between sensor voltages recorded by the LM 1 or LMA 3 and the indicated values This relationship will be programmed into the XD 16 for the selected ch
15. wing parts The XD 16 Module Analog Pointer LEDs Light Sensor Function _ _ Function indicator 1 Y oe Indicator 2 Main Humer Display Contral Button Record Indicator 2 1 Identifying the user interface features of the XD 16 The analog pointer LED s 21 total act as a digital needle The range and individual colors of this needle is freely programmable The Function indicators 1 and 2 are used to indicate between display heater warm up or O2 content when the XD 16 is programmed as AFR Lambda display default When used to display other channels the indicators can be used to indicate the sign of the displayed value By using the indicators as sign display positive or negative one of the three numerical displays is not wasted to show a sign This functionality is programmable The main numeric display shows the numeric value of the displayed channel When the XD 16 is used as AFR Lambda display it will also show the status of the wideband controller The light sensor allows the XD 16 to adjust its brightness to the light level of the environment At night the full on display would be much too bright and would interfere with the operation of the vehicle During sunlight the XD 16 will go to maximum brightness to allow readability The Control Button is used to control various aspects of the XD 16 and attached wideband controller or recording device like the LM 1 The record indicator w
Download Pdf Manuals
Related Search