eight head beam bar - GuangZhou GeLiang Lighting Technology Co
Contents
1. 9 l 3 E RG ML80B KEE amp H36A EIGHT HEAD BEAM BAR Guangzhou Geliang Lighting Technology Co Ltd Tel 8620 86872001 2 3 www rigelighting com SO OO IU T dores CONTENTS GENERAL INFORMATION SAFETY INSTRUCTIONS FEATURES GENERAL GUIDELINES FIXTURE OVERVIEW MOUNTING AND INSTALLATION UNDERSTANDING DMX CONTROL BOARD DMX CHANNEL TRAITS CLEANING AND MAINTENANCE TECHNICAL SPECIFICATIONS 1 YEAR LIMITED WARRANTY Disclaimer EIGHT HEAD BEAM BAR 1 GENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The Eight head beam bar has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit this fixtures uses a unique lamp that has very specific guidelines that must be strictly followed This manual contains important information regarding safety protocol that must be strictly adhered to at all times UNPACKING Thank you for purchasing the Eight head beam bar Every Eight head beam bar has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for damage and be sure all accessories necessary to operate the2. CAUTION Be sure a qualified electrician performs all electrical connections EIGHT HEAD BEAM BAR 8 CONTROL BOARD KEY instruction MENU Mode return the upper menu UP add value or choose the previous value DOWN decrease value or choose the next value TES sull E SUN ENTER Enter th b d the sett 7 Enter the sub menu or saved the setting a Y GEK imm A 001 A dn 01 A dn 03 Console mode setting imm d 000 imm r 000 a r 255 Red dimmer DMX address setting HH Irradiation angle Ta a N d a g 000 a 9 255 Green dimmer imm b 000 a Blue dimmer imm E 001 a E255 White dimmer imm AU 01 a AU 18 run eflec imm SP 01 a i AE 01 a slee 8 5 8j 8 8 Speed adjust HBH Efiect value non control SOU A Sound active color jump change SOU F Sound active color flash Addr DMX address setting This function is used to set the starting DMX address of the fixture Each fixturet controlled by DMX device has a starting address The DMX function is to ensure normal addressing A DMX address of the fixture allows it to communicate with the controller dn console mode selection This function allows you to use the console to control the fixture the fixture provide three EIGHT HEAD BEAM BAR different console mode dn01 9 DMX channal dn02 12
3. prong from the power cable Further instructions depending on installation and usage have to be adhered by a skilled installer and any safety problems should be addressed before attempting operation We recommend frequent cleaning of the fixture this will ensure operational longevity and crisp light output When cleaning please use a moist lint free cloth Never use alcohol or solvents There are no user serviceable parts inside this fixture Please refer all other service related issues to an authorized service technician EIGHT HEAD BEAM BAR 11 TECHNICAL SPECIFICATIONS Bower suppl C 100V 240V 50Hz 60Hz OW REE LED 10W pcs RGBW AINT total 8pcs LED life 50000h resnel lens 45 12 36 Drive Standard DMX 512 3 pole XLR Pin 3 Pin 2 Ground Pin 1 or 5 pole XLR n a Pin 5 n a Pin 4 Pin 3 Pin 2 Ground Pin 1 Starting DMX 001 rradiation angle rradiation angle 0 230 1 ength idth eight Weight net 12 1 YEAR LIMITED WARRANTY e A Hereby warrants to the original purchaser our products to be free of manufacturing defects in material and workmanship for a period of one years 365 days from the date of purchase e B For warranty service send the product only to the our factory All shipping charges must be pre paid If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any acces
4. remain clean and are never blocked Allow about 6 15cm between this fixture and other devices or a wall to allow for proper cooling 2 Be sure to unplug the Eight head beam bar from the power outlet before performing any service related issues 3 Never look directly into the lamp beam You risk injury to your retina which may induce blindness 4 For safe operation follow the Installation guide described in chapter two of this manual Operating the Eight head beam bar without suited safety aids such as safety cables or clamps can increase the risk of damage and or personal injury 9 Only qualified and certified personnel should perform installation 6 When mounting this fixture use only the original rigging parts included with this fixture Any structural modification will void the original manufactures warranty and may increase the risk of damage and or personal injury 7 Toreduce the risk of fire or shock do not expose this fixture to rain or moisture 8 Do not attempt to operate this fixture if the power cord has become damaged or frayed Important Notice Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims 3 FEATURES Irradiation angle 0 230 1 3 operation mode DMX controlled stand alone or sound activated 3 DMX Modes 9 Channel 12 Channel 36 Channel otrobe effect Electronic Power Supply AC 100V 240V 50
5. unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting customer support at the number listed below CUSTOMER SUPPORT We provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www rigelighting com for any comments or suggestions For service related issue please contact us Voice 8620 86872001 2 3 Fax 8620 86872001 2 3 E mail support rigelighting com Forum www rigelighting com net Working Time BeiJing Time Monday to Friday 08 00 12 00 13 30717 30 18 30 20 30 Saturday 09 00 12 00 13 307 17 00 Note all the rest of China s holidays Warning To prevent or reduce the risk of electrical shock or fire do not expose this unitto rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty EIGHT HEAD BEAM BAR Please do not discard the shipping carton in the trash Please recycle whenever possible aus portan t Damages caused by the disregard of the instructions in this user manual are not subject to warranty Never open this fixture while in use During the initial operation of this fixture a light smoke or smell may emi
6. DMX channal dn03 36 DMX channal Angl Irradiation angle positioning Irradiation angle settings Irradiation angle 0 230 FL gl bl El dimming This section is used for the lighting of the red green blue white linear dimming AUTO run the built in effects This section is used to run the lamps built in program A total of 18 effects to choose from SPED the effect of the speed controller This function is used to adjust the running speed of the built in effects Alef display value This function is used to display the current built in effects run step uncontrollable SOUA sound active color jump change This function is used to turn the sound active function In this mode fixture active by the sound SOUF sound active color flash This function is used to turn the sound active function In this mode fixture active by the sound Synchronous operation setting no console Host in the AUTO ALEF SOUA SOUF mode Slave A 001 Synchronous operation set console mode Host dn01 dn02 dn03 Slave A 001 EIGHT HEAD BEAM BAR 9 DMX CHANNEL TRAITS dn 01 Console mode settinc Irradiation angle 0 100 e ps Motor Speed fast to Strobe effect ton mm CHe 0255 __ Green dimmer 0 100 LL cH7___ o 255 Bluedimmer 0 100 7 cms 0255 White dimmer 0 100 LL CH9 lo 255 __ Effect speed fastto slow E 150 159 __ jeffect10 LL cmo o255 __ Effect
7. Hz 60Hz Fresnel lens High power Cree LEDs RGBW 4IN1 10W pcs EIGHT HEAD BEAM BAR 4 GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage in nightclubs in theatres etc Do not attempt operation or installation without a proper knowledge on how to do so This fixture was designed for indoor use only Consistent operational breaks may ensure that the fixture will function properly for many years to come Do not shake the fixture around Avoid brute force when installing or operating the device While choosing an installation location please be sure that the fixture will not be exposed to extreme heat moisture or dust The minimum distance between the fixture and a wall or flat surface should be at least 1 meter about 3 5ft Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environment always be sure to use mounting hardware no less than M10 x 25 mm also be sure the hardware is insert in the pre arranged screw holes in the base of the fixture When using the quick release Omega cam lock system be sure the quick lock fasteners are locked in the quick lock holes correctly Do not attempt to operate this fixture until you have familiarized yourself with its functions Do not permit operation by persons not qualified for operating this type of theatrical fixture most damages are the result of operations by nonprofessionals Please use
8. Speed fast to slow dn 02 Console mode settinc CH o255 __ radiation angle 01009 LE CH2 0255 Motor Speed fast to slow E cuo o 255 Tent ammer o 100 o or Ld Strobe effect nn rn nne dn 03 Console mode settinc cmi 0 255 madiation angie 0 100 J 7 CH2 o 255 Motor Speed fast to slow E CH3 0 255 Total dimmer 0 100 cH4 lo Jorr en 1 255 Strobe effect Ld the Tst head the 2nd head the 3rd head the 4th head CH18 0 255 Green dimmer 0 100 CH19 0 255 Blue dimmer 0 100946 CH20 0 255 White dimmer 0 100926 EE the 5th head the 6th head the 7th head the 8th head EIGHT HEAD BEAM BAR CH36 0 255 White dimmer 0 10096 EIGHT HEAD BEAM BAR 10 CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall 2 There must not be any deformations on the housing rigging hardware and rigging points ceiling suspension trussing Damaged rigging points or unsecured rigging could cause the unit to fall and serious injure a person 3 All mechanical parts and motors should not show any traces of serious wear and should rotate freely 4 Electric power supply cables must not show any damage material fatigue or sediments Never remove the ground
9. able law all implied warranties made by us in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall we be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to our products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published 13 Disclaimer The contents of this manual are subject to change without notice if in doubt consult your local hotline Copyright The data at RIGE Technology Co Ltd Guangzhou GeLiang Lighting Technology Co Ltd common to all to prohibit any unauthorized copying printing and dissemination
10. ation yourself Improper installation can result in bodily injury e Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The Eight head beam bar provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly Securing the Eight head beam bar Regardless of the rigging option you choose for your Eight head beam bar always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 7 UNDERSTANDING DMX DMX 512 DMX is short for Digital Multiplex This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactu
11. e moving heads together through serial linking The cable that should be used is two conductor shielded DMX cable with XLR input and output connectors Always be sure daisy chain your in and out data connections never split or Y your DMX connections unless you are using an approved DMX splitter DMX 512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a line terminator Elation part DMX T PACK will decrease the possibilities of erratic behavior Termination reduces signal errors and AS avoids signal transmission problems and interference It is always advisable to connect a DMA terminal Resistance 120 Ohm 1 4 W between PIN 2 DMA and PIN 3 DMX of the last fixture IKE o Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The following chart details a proper cable conversio
12. n 3 Pin XLH to 5 Pin ALR Conversion Conductor 4 Pin XLR Female Out 5 Pin XLR Male In Netused Pm4 Do Not Use Fixture DMX addressing All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture responds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the base of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion in other words changing the settings of one channel will affect all the fixtures simultaneously If you set each fixture to a different DMX address each unit will start to listen to the EIGHT HEAD BEAM BAR channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture EXP In dn01 mode this fixture is in 9 channel mode you should set the starting DMX address of the first unit to 1 the second unit to 11 10 1 the third unit to 21 11 10 and so on
13. pin XLR connector for data input and data output the figure on the next page is of a 3 Pin XLR connector If you are making your own cables be sure to use two conductor shielded digital DMX cable rated at 120 ohms this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers Your cables should be made with a male and female XLR connector on either end of the cable Also remember that a DMX line must be daisy chained and cannot be split unless using an approved DMX splitter COMMON DMX512 OUT ne on DMX512 IN 3 PIN XLR NS M 92 3 PIN XLR Be sure to follow the above figure when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior Dx Output IMX Input DINE Output MX Input Pin XLE Socket Pin XLR Sockel 5 Pin XLR Sockel Fin XLR Sockel i brand 2 Data a de Ela 4 DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head Please refer to the diagram os or Input Output Input Output Ground ALERT k Data 4 pen 5 Open EIGHT HEAD BEAM BAR below You can chain multipl
14. res to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and EIGHT HEAD BEAM BAR data OUT XLR terminals located on the fixtures most controllers will only have output jacks DMX Linking To ensure proper DMX data transmission always use proper DMX cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain The Eight head beam bar can be controlled via DMX 512 protocol The Eight head beam bar is a 22 channel DMX fixture 23 default can also be 21 or 34 The DMX address is set electronically using the controls on the LCD menu Data Cable DMX Cable Requirements For DMX and Master Slave Operation Your fixture and your DMX controller require a standard 3 pin or 5
15. sories are shipped with the product we shall have no liability what so ever for loss of or damage to any such accessories nor for the safe return thereof e C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which we concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the our factory unless prior written authorization was issued to purchaser by us if the product is damaged because not properly maintained as set forth in the instruction manual MEER EIGHT HEAD BEAM BAR D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above we will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of us under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of us E Our company reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applic
16. t from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time This device falls under protection class 1 Therefore it is essential that the device be grounded properly All electrical connections should be performed by a qualified electrician Be sure the available voltage matches the voltage requirements of the unit Be sure the power cord is never crimped or damaged If the power cord is damaged replace it immediately with a new one of similar power rating Always disconnect from main power before performing any type of service or any cleaning procedure Only handle the power cord by the plug Never pull out the plug by tugging the wire portion of the cord This fixture is designed for use indoors Use of this fixture outdoors will void the manufactures warranty Please be aware that damages caused by manual modifications to the device are not subject to warranty EIGHT HEAD BEAM BAR 2 SAFETY INSTRUCTIONS The Eight head beam bar is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual We will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual 1 Always be sure that the fan and the air inlets
17. the original packaging to transport the fixture in for service EIGHT HEAD BEAM BAR 5 FIXTURE OVERVIEW 1 Omega holders 3 2 Clamp 3 Safety rope 4 Quick lock fastener Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personal Before mounting the fixture to any surface make sure that the installation area can hold a AER EIGHT HEAD BEAM BAR minimum point load of 10 times the device s weight 9 Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable e Never stand directly below the device when mounting removing or servicing the fixture Mounting The Eight head beam bar is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the install
Download Pdf Manuals
Related Search