Home
Orbit Marine – Instructions - Current-USA
Contents
1. N Orbit Marine LED Light CUPPeNt with 24 hour Ramp Timer Pro LED Controller Quick Installation Guide What s included 1 Orbit Marine LED light fixture with dual actinic dual daylight LEDs with adjustable docking legs 1 12VDC transformer 1 Ramp Timer Pro LED controller 1 Wireless IR remote Installing the Orbit Marine 1 Unpack light fixture and components remove any plastic film on light fixture 2 Slide the adjustable docking legs on the side of the fixture to match the length of your aquarium 3 Set fixture on aquarium and connect to the Ramp Timer Pro included as per instructions below Orbit Marine LED Light Fixture Ramp Timer Pro Controller GBOeOBOROBRBEBaRBERERBAaBRBREAERaEARBBERBaaAaBEaeEaE ea HEEG gaE EOE OEE GEOG RBARPARBAEABARB AG A ramp TIMER PRO f IR Sensor 12VDC Transformer Connecting the Ramp Timer Pro to the Orbit Marine 1 Connect your 12VDC transformer to the female DC plug on the timer plug transformer into GFCI protected AC outlet Ensure a drip loop is created before the outlet as shown on page 6 Connect your LED light s to the male DC plugs on the timer Blue light channel dawn dusk moonlight connects to Line 1 White light channel daylight connects to Line 2 3 Remove plastic cover from wireless remote and remove clear plastic tab located at the bottom of the remote 4 Locate a dry location not near water or salt creep Clean area thorougly 5
2. or modifications If you discover a defect please see your retail store or point of purchase Current USA Inc will at its option repair or replace the product at no charge to you provided you return it during the warranty period A copy of the bill of sale is required as proof of original purchase date in the event the product needs repairs within the warranty period Please see your dealer for return options and warranty replacement parts This warranty applies only to products by or for Current USA Inc that can be identified by trade name or logo affixed to them Current USA Inc does not warrant any products that are not Current USA Inc This warranty does not apply if the product has been damaged by accident abuse misuse or misapplication or if the product has been modified without the written permission of Current USA Inc or if any Current USA Inc logos have been removed or defaced THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS WHETHER ORAL OR WRITTEN EXPRESSED OR IMPLIEOURRENT USA INC SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO LOST PROFITS DOWNTIME GOODWILL DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY AND ANY COSTS OF RECOVERING ANIMALS PLANTS TANKS OR OTHER AQUARIUM RELATED ITEMS AND OR EQUIPMENT CURRENT USA INC IS NOT RESPONSIBLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY O
3. day Controls line 2 Intensity adjust Moonlight Used for programming Used for setting the Used to program channel 2 usually white min max intensity for lunar light duration each channel Manual color adjustment Provides manual adjustment of each channel Blue buttons adjust line 1 blue white buttons adjust line 2 daylight Memory Used for storing lighting schedules in memory See page 2 to review pre installed lighting schedules Dynamic lighting modes Provides on demand weather effects Two cloud cover modes fading moonlight and storm with lightning SOOO When using your wireless remote point the remote directly at the IR sensor located on the Ramp Timer Pro It is important to have a direct line of sight between the remote and the controller MAX INTENSITY OFF TIME Sunset MOONLIGHT PA BOA i HOUR INTENSITY current Page 3 Detailed Programming Instructions The following detailed steps will guide you through customizing and programming your Ramp Timer Pro Please be sure to follow our Quick Installation Guide and set the clock before following the below steps Programming Individual Lighting Channels The Ramp Timer Pro features two channels of lighting which can be independently controlled Channel 1 Line 1 should be connected to your blue spectrum lights for dawn dusk actinic moon lighting Channel 2 Line 2 should be connected to your white spectrum lights for daylight The
4. 15 am 8 00 am 8 30 am 8 00 am 8 30 am 8 00 am 8 30 am Off Time 6 00 pm 6 15 pm 4 00 pm 3 00 pm 8 00 pm 7 30 pm 4 00 pm 3 00 pm Sunrise Sunset Fade 15 min 15 min 30 min 30 min 15 min 15 min 30 min 30 min Minimum Intensity 10 0 0 0 10 0 0 0 Maximum Intensity 100 100 60 60 100 100 80 80 Moonlight Duration 4 hours 0 0 0 4 hours 0 0 0 ox Ss current Page 2 Wireless Infrared IR Remote Guide O TOK O90 800 O 00O Q gt DO lt vE EII vE IIT Creer Orbit Marine LED V 1 O www current usa com current 2 Digital LCD Display Guide Ramp Timer Pro LCD Display The backlit LCD display features the indicators pictured to the right The indicators are shown on the display when you are using the remote in one of the programming modes listed above Main on off Manually turns lights on off Factory Default settings Resets the four memory settings to factory default Manual color spectrum mode Resume programming Allows you to select a color Exits a dynamic mode and resumes spectrum brightness to memory timer lighting schedule sem Sets 24hr clock finer Main adjustment gt Enter Clock Used for setting the Used for setting hour Stores setting in minutes or settings memory Controls line 1 ag rogram on off ar Dawn dusk Used for programming TW Used for programming Used to program channel 1 usually blue on off for each channel ramp and dim current time of
5. 4 SL 1 SL 2 SL 3 or SL 4 will flash and any changes are now saved into the memory To reset the memory settings to the factory default press DEFAULT Gorau for 5 seconds see pg 5 This will reset the controller memory for all four memory settings Set On Off Times e To program Channel 1 or 2 press CH1 or cH e Press ON TIME ON1 or ON2 will quickly flash and the display indicator will blink ON TIME Press HOUR and MINUTE until the desired on time is displayed e Press OFF TIME ti OFF1 or OFF2 will quickly flash and the display indicator will blink OFF TIME Press HOUR and MINUTE on until the desired off time is displayed e Press ENTER Program Channel Sunrise Sunset Suration e To program Channel 1 or 2 Press CH1 por CH2 e Press SUNRISE SUNSET E FADE will quickly flash and the display indicator will blink both SUNRISE and SUNSET F will display with the number of minutes currently programmed for the gradual ramp and dim The number of minutes can be changed using the HOUR and MINUTE fou The gradual ramp dim is adjustable from 0 30 minutes e Press ENTER Program Moonlight Duration e To program moonlights on Channel 1 or 2 Press CH1 or CH2 e Press MOONLIGHT ED N1 or N2 quickly flashes and the display indicator will blink MOONLIGHT Adjust the duration of your moon light setting from 0 to 6 hours using the HOUR and MINUTE mw Complete programming by pressing ENTER re Note The moonligh
6. R REPLACEMENT OF EQUIPMENT OR PROPERTY OR ANY COSTS OF RECOVERING OR REPRODUCING ANY EQUIPMENT ANIMALS OR PLANTS USED OR GROWN WITH CURRENT USA INC PRODUCTS Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from jurisdiction to jurisdiction Grounding Instructions This LED timer must be powered with an ETL or UL Listed Transformer To avoid possible electric shock this transformer must be plugged into a GFCI wall outlet that is installed and grounded in accordance with all appropriate codes and ordinances For more information and to register your product please visit www current usa com AA AN current Page 6
7. Use velcro included to mount Ramp Timer Pro to mounting location 6 Press SET CLOCK 7 Press HOUR and MINUTE until the current time of day is displayed 8 Press ENTER clock is now set 9 Press TIMER M1 or TIMER M3 twr Pre programmed lighting schedule is complete See following page for pre programmed lighting schedules Note Ramp Timer Pro and remote are NOT waterproof Ensure neither are located in a location of splashing water or salt creep current Page 1 Detailed Installation Instructions Please read the following guides before following the detailed programming instructions located on page 4 Programming Feature Guide The Ramp Timer Pro features two independent lighting channels with the following Program on off times for each channel Adjustable intensity 0 100 for each channel Adjustable ramp up sunrise dim down sunset 0 30 minutes Adjustable moonlight duration 0 6 hours On demand color spectrum adjustment On demand weather simulation including cloud cover fading moonlight and storm with lightning Four memory locations for storing custom lighting schedules each are pre programmed by default see below Pre programmed Lighting Schedule Guide The Ramp Timer Pro features four pre programmed lighting schedules These schedules are located in memory buttons labeled TIMER M1 TIMER M2 TIMER M3 TIMER M4 To customize any of the settings please follow the detailed Progr
8. amming Instructions located on Page 4 Using the graph and table below select from any one of the pre programmed lighting schedules Once you select a lighting program simply press TIMER M1 TIMER M2 TIMER M3 or TIMER M4 and the controller will automatically enter into the selected lighting schedule utton Lighting Schedule 10 hours full intensity 15 minute sunrise sunset with 4 hours of 10 blue moonlight This is a great lighting schedule for most aquariums 7 hours of low medium intensity lighting 30 minute sunrise sunset with no moonlight A perfect coral acclimation program Run this a few days when adding new corals to your tank rimer 12 hours full intensity 15 minute sunrise sunset with 4 hours of 10 blue moonlight Ma A longer lighting schedule for power growers 7 hours of medium high intensity lighting 30 minute sunrise sunset with no moonlight Great for fish and coral acclimation Run a couple days when adding new fish invertebrates or corals amp Programmed Off Time Maximum Intensity Light Intensity Dim Down Minimum Intensity Sunset Ramp Up Sunrise Moonlight Lights Off Duration Programmed Time 24 Hour Lighting Cycle On Time M1 10 Hour M2 Coral M3 12 Hour M4 Coral TIMER i i Full Intensity Acclimation Full Intensity M3 Acclimation Light Program i CH1 Blue CH2 White CH1 Blue CH2 White CH1 Blue CH2 White CH1 Blue CH2 White On Time 8 00 am 8
9. and warnings on the fixture and power cord DO NOT REMOVE THE WARNING LABEL e f an extension cord is necessary a cord with a rating at least 15 amperes should be used A cord rated for less amperes or watts than the fixture rating may overheat Care should be taken to arrange the cord so that it will not be tripped over or pulled e Do not look directly into the LEDs Important Warnings Drip Loops Drip Loops should always be used to help prevent water from traveling along the cord and coming into contact with an electrical outlet Drip loops must always be below the level of the outlet If the plug or outlet does get wet DO NOT TOUCH the cord Disconnect the fuse or circuit breaker that supplies power to the system After disconnecting the power unplug and examine for the presence of water AC Power Cord Drip Loop Current USA Inc One Year Limited Warranty Current USA Inc warrants this product against defects in materials and workmanship of a period of ONE 1 YEAR from the date of original retail purchase and is not transferable Warranty on all Products including Aquariums is limited to replacement of the product and does not cover fish loss personal injury property loss or direct incidental or consequential damage arising from the use of this product Note Current USA Inc One Year Limited Warranty does not cover damage caused by the following improper installation saltwater corrosion electrical surges
10. attempt repairs yourself return the appliance to an authorized service facility for service or discard the appliance e Carefully examine the fixture after installation and BEFORE you plug it into the GFCI wall outlet Be sure there is no water on any part of the light fixture or the timer e Never plug in a wet cord If a plugged in unit or socket does get wet DON T touch it Instead promptly disconnect the fuse or circuit breaker that supplies power to the fixture Then you may unplug the fixture and examine for the presence of water e Never operate a fixture that is damaged or malfunctioning discontinue use immediately and return the appliance to an authorized service facility e Close supervision is necessary when any appliance is used by or near children e Always unplug the fixture when not in use before putting on or taking off parts and before cleaning Never pull the cord to unplug from the GFCI e Do not use the fixture for anything other than intended use The use of attachments not recommended or sold by the fixture manufacturer may cause an unsafe condition and will void your warranty e Do not install or store the fixture where it will be exposed to the weather or to temperatures below 0 Celsius or 32 Fahrenheit e Do not operate at temperatures above 50 Celsius or 122 Fahrenheit e Ensure the fixture is securely installed before supplying power to the unit e Read and observe all the important notices
11. ey again and hold for 5 seconds SF 1 SF 2 SF 3 or SF 4 will appear on the LCD display indicating the changes have been saved successfully Reset to factory default settings To reset the controller memory schedules back to the factory defaults simply press DEFAULT SETTINGS e and hold for 5 seconds This will reset the controller memory for all four memory settings Step 4 Dynamic Lighting Modes Four dynamic fade modes are available on demand using the wireless remote These modes mimic common weather patterns found in nature and add amazing lighting effects to your aquarium To use simply e Point the wireless remote to your controller and press one of the four dynamic modes Partly Cloudy P 02 will display Very Cloudy P 03 will display Fading Moonlight P 04 will display O O Storm with lightning P 05 will display e When your weather pattern is complete simply press RESUME and the controller will go back to your last programmed wie time mode Note If your controller is left on a dynamic mode maybe to help you fall asleep it will remain in this mode f N until you press RESUME eso current Page 5 AC Protected GFCI Outlet IMPORTANT WARNINGS SAVE THESE INSTRUCTIONS This is NOT a page of legalese It contains important safety information that you should read and save for future reference Remember you can always quickly access instructions for all our products at www current usa com e Never
12. following diagram is a simple flow chart showing the programming steps available for each lighting channel ON TIME Determines what time your lights will begin to turn on om OFF TIME Determines what time your lights will begin to turn off SUNRISE SUNSET FADE The duration of the ramp up and dim down 0 30 minutes MOONLIGHT The duration of the moon light schedule 0 6 hours a MAXIMUM INTENSITY The maximum brightness 0 100 lt MINIMUM INTENSITY The minimum brightness 0 100 O I eee D I Please note each programming step can be completed independent OFF MAX MIN i FADE of the others by simply pressing CH1 or CH2 followed by the program TIME INTENSITY wtENsity Programs adusting the setting with HOUR and or MINUTE mn then ENTER For example to change the duration of sunrise and sunset duration for channel 2 simply Press CH2 Press SUNRISE SUNSET Adjust duration by pressing Press ENTER re Before Programming The Ramp Timer Pro features four pre programmed lighting schedules located in memory buttons Timer M1 M2 M3 M4 Schedules can be reviewed on page 2 We highly suggest choosing one of these programs for a lighting schedule or adjusting your settings from one of them manually To choose one press Timer M1 M2 M3 or M4 and SL 1 SL 2 SL 3 or SL 4 will flash on the LCD Adjust any the programmed settings using the below steps then press the same memory button for 5 seconds Timer M14M2 M3 or M
13. t intensity is programmed by using your minimum intensity setting for each channel The moon light mode is designed to replicate natural moonlight so it is only programmable for a 0 6 hour duration OX current Page 4 Programming Light Channels continued Find the Minimum And Maximum Intensity Of Color Spectrums Before setting your minimum and maximum lighting levels for each channel we highly recommend utilizing the Manual Color Spectrum Mode key M located at the top of the remote This button allows you to manually adjust the lighting intensity for each channel on demand and will display the intensity from 0 100 on the LCD Minimum intensity moonlight spectrum maximum intensity daylight spectrum To adjust e Press M1 e P 01 will display on LCD e Press Blue arrows up or down to manually adjust Channel 1 Wey e Press White arrows up or down to manually adjust Channel 2 e Adjust the colors until your desired brightness and color spectrum are acheived e The intensity can be used as a reference when programming your minimum and maximum settings Setting Minimum And Maximum Intensity Of Each Channel e Press CH1 or CH2 e Press MAX INTENSITY OF b1H or b2H quickly flashes and the display indicator will blink MAXIMUM Adjust the maximum light intensity for channel using the HOUR and MINUTE w Intensity can be adjusted from 0 100 e Press MIN INTENSITY s b1L or b2L quickly flashes and the display indicator
14. will blink MINIMUM Adjust the minimum light intensity for channel using the HOUR C and MINUTE Intensity can be adjusted from 0 100 When your lights ramp down they will reach your minimum lighting level and run per the programmed moonlight duration time 0 6 hours e Press Enter 6 Settings are now complete Memory Functions The Ramp Timer Pro features five memory locations Main Color Spectrum M This memory location stores color spectrum only Pressing M1 m allows you to use the blue and white manual adjustment arrows to find color spectrums you like The intensity of each channel is displayed on the LCD as the arrow buttons are pushed You can use this as a reference or simply exit the program by pressing the RESUME key Your last color settings will be saved in the M1 memory and can be changed at any time Customizing the Pre Programmed Lighting Schedules These four memory locations store complete 24 hour lighting schedules To make things easy we have pre programmed all four memory locations providing two lighting schedules and two coral acclimation modes Please review each of the pre programmed schedules on page 2 Each pre programmed timer schedule can be customized at any time by simply e Press TIMER M1 TIMER M2 TIMER M3 or TIMER M4 SL 1 SL 2 SL 3 or SL 4 will display on the screen e Adjust any of the channel settings by following the steps e When programming changes are complete press the same memory k
Download Pdf Manuals
Related Search
Related Contents
Poss - Salle D`eau Sport Les Certificats d`Economies d`Energie ou CEE, mode d`emploi Origin Storage 128GB MLC SATA 2.5" 4 - Printers - Konica Minolta American Standard 4504 Indoor Furnishings User Manual IBM Flex System FC3172 2-port 8Gb FC Adapter Euro-Pro SV1106 User's Manual TABLE DES MATIÈRES - Pride Mobility Products EverFocus EKB200 other input device Hypertech Water Heater 41042 User's Manual Copyright © All rights reserved.
Failed to retrieve file