OEM BS2sx - Rev C Assembly Instructions
Contents
1. be marked as 50 00 50 MHz This component is polarity insensitive That is to say that it doesn t matter which direction it is installed it will still work Install the ceramic resonator where the XTAL designator is Next grab the electrolytic capacitor It resembles a small cylinder with two long legs emerging from one end Be particularly careful when installing this component It is polarity sensitive if it is installed backwards it can pop like a miniature firecracker and emit a horrible stench after it is powered up The electrolytic capacitor will have the negative lead marked with one or more signs Install the leg NOT marked with the signs in the hole closest to the sign in C1 s lead lead space on the PCB Now find the 3906 PNP transistor it looks like a black bead with three legs and bears the mark 3906 Insert it into the group of three holes marked Q3 on the PCB Please note that the middle leg must be bent slightly to accommodate the hole patterns Avoid excessive bending The white silkscreen on the PCB will guide you as to how to orient this component Front View Side View There are three other components that closely resemble the transistor from the step above The two NPN transistors marked 3904 should be installed into locations Q1 and Q2 The brown out detector the one not marked 3904 or 3906 should be installed into location U32. 3 4 Next find the two resistor networks A resistor network looks like a comb for a Barbie Doll On the resistor network Rnet there is a dot printed near one end to signify at which end Pin 1 is located On the PCB look for two single line groups of eight pads marked RN1 and RN2 Find Pin 1 on each of the Rnets and orient them to fit through the square pad on each of the RN1 and RN2 groups on the PCB 5 The IC sockets are next in line Nearly all ICs have a Pin 1 marker that denotes the location of Pin 1 It is important to Pin 1 gt install chips with the proper orientation since more often than not installing a chip backwards will result in damage to the chip and or surrounding circuitry For the IC sockets that you will be installing there is a notch on the edge of one of the short sides This notch denotes the top of the chip When oriented properly Pin 1 is the top left pin as depicted in the drawing to the right Install both the 28 Pin and the 8 Pin DIP sockets into U1 and U2 respectively PAYAL X A Rev 1 4 sales technical support 916 624 8333 e fax 916 624 8003 6 4 2008 email stamptech parallaxinc com Page 1 OEM BS2sx 10 11 12 13 14 The next component to install is the ceramic resonator The ceramic resonator looks like a coffee bean although sometimes they are blue instead of brown with three metal legs sticking out from one side and should
3. OEM BS2sx 27302 Kit 27294 Assembled OEM BS2sx Rev C Assembly Instructions This document is a guide that will aid you in the assembly of your OEM BS2sx It is assumed that you have the proper equipment and possess the skills necessary to safely assemble electronic components Generally it is best to start with the lower profile components and then work your way to the tallest components This is often true because in tight places lower profile components are more difficult to get to with taller components in the way 1 The lowest profile components on the board are the resistors CIILD There are two 4 7K Ohm resistors and one 10K resistor The resistors should have color bands around them which signify their value o 4 7K Ohm resistor color bands Yellow Violet Red and Gold o 10K Ohm resistor color bands Brown Black Orange and Gold Resistors are polarity insensitive which means that it doesnt matter direction they are inserted o Install the 4 7K Ohm resistors where designated by R1 and R2 o Install the 10K Ohm resistor where designated by R3 2 he next lowest profile component on the board is the 20 pin right angle strip header The side with the angle should be inserted into the PCB as shown in the drawing to the right 3 Next find the two 0 1 uF ceramic capacitors Like the resistors it doesn t matter which way these are installed Install the two capacitors where designated by C2 and C
4. Pay close attention to orientation as indicated by the white shapes surrounding these locations Next you will install the 9 pin D Sub connector This is the only component that looks like it will plug into a serial cable Install it on the top side of the PCB The last component to solder is the voltage regulator VR1 It is a relatively large plastic square with a metal tab protruding from the top Install this with the metal tab closest to the 9 pin D Sub connector This component like the electrolytic capacitor is polarity sensitive and MUST be installed correctly lest ye suffer smoke and fire and the gnashing of teeth Be sure you clean the board before you stuff the Basic Interpreter IC and the EEPROM IC into U1 s and U2 s respective sockets That s it You ve done it You ve made your own BASIC Stamp Visually inspect the board Before applying power to it repair any and all soldering errors and verify that all components have been installed in the proper locations and with the correct orientation Download and run the latest version of the BASIC Stamp Editor from either the CD or the website Connect the OEM BS2sx to a PC serial port and power it up Please consult the Basic Stamp manual also available from either the CD or our website for guidance on using your BS2sx Please select the BS2sx as the default stamp before attempting to identify or download a program to your new BS2sx You must also name the stamp program you wish t
5. e other but never both e WARNING Interpreter chips are available in a number of packages and the pinouts may be different than the DIP chip depicted in this document When laying out your board be sure to specify the correct package and use the correct pinout Specifically the SOIC PAAU AX amp Rev 1 4 sales technical support 916 624 8333 e fax 916 624 8003 6 4 2008 email stamptech parallaxinc com Page 3 OEM BS2sx package has the same pinout as the DIP but the SSOP is different Ex for the BS2 Ul PBASIC2 P Ul PBASIC2 SO Ul PBASICZ SS PAAU AX 4 N TD Rev 1 4 sales technical support 916 624 8333 e fax 916 624 8003 6 4 2008 email stamptech parallaxinc com Page 4 OEM BS2sx JD ee te LI si uu es B Le ij e de aA LI 9 e ri ry C E b on Eas INC i e aj e ye eP Met oe m 2000mil yy oe lols s S e e 89 nu T t 8 a Uji 3j dm a Jez le e 7 En T BD alte s 9 V e c im E Sree V7 amp OQ D 0 OQ OL OL 0 OL OL OL CL Gc GL LOL i RARER ERE EEE EE t t ta oe se 5x L 0 6 550 0558565550658 UUU The above images of the board layers are not to scale Please visit www parallaxinc com for the actual source and gerber files This board was designed using Mento
6. hey are not in finished product form If you wish to obtain FCC approval you must first design the stamp into a product then seek FCC approval of the whole product e We use a minimum complement of components to effect an interface between the high levels of RS232 and the relatively low levels of TTL Some customers may need or want to use a different approach Regardless of how the line levels are interfaced there are two important things to note the idle state of the serial input line at the interpreter Sin is high so you may need to use pull up resistor on the Sin pin also there must exist some form of loop back from Sin to Sout so that the Stampw exe software can communicate with the stamp e Symbols Various acronyms are used throughout this manual Here s a brief glossary OEM Original Equipment Manufacturer BS2sx Second generation Basic Stamp using the SX28 interpreter chip IC Integrated Circuit DIP Dual In line Package PCB Printed Circuit Board Vin Input Voltage Specifically the positive side of the supply DC voltage Vdd 5Vdc the positive side Vss Ground the negative side of the supply DC voltage e Powering up your OEMBS2sx There are two ways you can power up your OEMBS2sx 1 You may apply 6 24 Vdc to the Vin pin and ground to the Vss pin OR 2 You may apply 5Vdc to the Vdd pin and ground to the Vss pin Please note that these two methods are mutually exclusive do one or th
7. o download with a bsx extension PAYAL X A Rev 1 4 sales technical support 916 624 8333 e fax 916 624 8003 6 4 2008 email stamptech parallaxinc com Page 2 OEM BS2sx OEM BS2sx Rev C Design Notes One of the main purposes behind the OEM BS2sx is making it easier to embed a BS2sx into an OEM design When designing the BS2sx into an your product please consider the following e Power Supply The Basic Interpreter requires a clean 5 Vdc supply The LM2940 was selected because of its wide operating range built in protection features and ability to deliver up to 1 Amp of current The value of the output capacitor C1 was based on the manufacturers recommendation Be sure to consult the manufacturer s recommendations for input and output capacitance selection for the regulator that you will be using in your design Also if the Basic Interpreter will be located more than a couple of inches away from the power supply it may be a good idea to add a 0 1 uF ceramic capacitor across Vdd and Vss at the Basic Interpreter IC e Resonator Location Note that the resonator on the OEM BS2sx board is located adjacent to the Basic Interpreter When laying out your board please choose a location for the resonator that is as close as possible to the Basic Interpreter and has the shortest circuit traces possible to ensure reliable operation e Regulatory Warnings Stamps and their constituent components are not FCC approved T
8. r Graphics PADS Layout software The leftmost image is the top lay silk and board dimensions The center image is the top copper layer The rightmost image is the bottom copper layer as viewed through the board The Rev C version of this board depicted above uses two layers Of course you may wish to use only one layer to reduce the cost of manufacturing Lh2940 5 0 PBASIC2 P BS2SX DP RC a bo o PAPALLAX 7 N TD Rev 1 4 sales technical support 916 624 8333 e fax 916 624 8003 6 4 2008 email stamptech Q parallaxinc com Page 5
Download Pdf Manuals
Related Search