Manual - GOED licht en geluid
Contents
1. Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc E INSTALLATIONS Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable 05 Never stand directly below the device when mounting removing or servicing the fixture from a ceiling or set ona flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all instal2. which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box OPTIONAL USA Standard Euro Standard UK Standard 9 A Moving Head IEG IN Signal Cable 1PC Power Cable 1PC User Manual Power Out 1PC Hanging Kit IRE Safety Cable 1PC User Manual 1PC 02 FEATURES amp SPECIFICATIONS Features e A50W white LED lamp e 50000 hours life span and low power consumption e 8 16 bit smooth and precise resolution for PAN TILT movement e 360 540 630 PAN and 90 180 270 TILT movement e Scan position memory auto reposition after unexpected movement Specific optic system with 2 projection angle e Improved optics and flat beam field e 1static gobo wheel with 17 gobos plus open e 1 color wheel with 14 colors plus open e Variable direction rainbow effect with speed adjustable e 8 facet prism with variable speed and direction e 0 100 linear LED dimmer e 25T sec high speed LED shutter strobe effect with variable speed e Preset variable random strobe and dimming pulse effect e 9 11 DMX channels USITT DMX 512 e DMX512 master slave and sound activated controllable or auto operation 7 built in programs e DMX recorder and edit function integrated e Red
3. 9 80 87 Color 10 88 95 Color 11 96 103 Color 12 104 111 Color 13 112 127 Color 14 128 189 Forwards rainbow effect from fast to slow 190 193 Color rotation stop 194 255 Backwards rainbow effect from slow to fast 0 4 Open 5 9 gobo 1 10 14 gobo 2 15 19 gobo 3 20 24 gobo 4 25 29 gobo 5 30 34 gobo 6 35 39 gobo7 40 44 gobo 8 45 49 gobo 9 50 54 gobo 10 55 59 gobo 11 60 64 gobo 12 6 4 Gobo 65 69 gobo 13 wheel 70 74 gobo 14 75 79 gobo 15 80 84 gobo 16 85 89 gobo 17 90 97 Gobo 1 shake slow to fast 98 105 Gobo 2 shake slow to fast 106 113 Gobo 3 shake slow to fast 114 121 Gobo 4 shake slow to fast 09 EJ unpackinc Thank you for choosing our MINIBEAM 50 For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs The MINIBEAM 50 is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos The MINIBEAM 50 adopts a 50W white LED lamp
4. AN angle options TILT angle options Up Mode 08 LED DISPLAY Down Enter MIC Regardless of the rigging option you choose for your MINIBEAM 50 always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle Ed pmx 512 CONTROL CONNECTIONS Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator DMX OUT DMX IN Fuse BOWER IN Power Switch POWER IN DMX IN COMMON 2 Data MPH AGO owe N DMX Output DMX Input DMX512 OUT DMX512 IN 3 Pin XLR Socket 3 Pin XLR Socket 3 PIN XLR 3 PIN XLR 07 Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 1 50W white LED Control Signal DMX512 master slave and sound activated or auto operation Control Channel 9 11 DMX channels USITT DMX 512 Power Consumption 55W Dimensions 149 D 270 W 364 H mm Packing Dimensions 350 D 450 W 240 H mm Net Weight 5 8kg Gross We
5. EZ MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instr
6. background LED display e Powercon connector IN e 3 pin XLR connectors IN OUT e Fan cooling system Constant temperature readout and management function e 45 C max ambient temperature e IP20 protection rating e 55dB at 3 dB rating e 1 hanging kit Static gobos Colors DODDOS O See OGOOGO 00e QOOOOO 000 03 For installations where the DMX cable has t Please see illustrations below orunalongdistance 1200 or is in an electrically noisy environment such as ina discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain EE menu OPERATIONS PIN3 PIN2 SLAV A001 AXXX AXXX ON OFF SLAV DMX address setting IP1 8 ALON AU A MAST AU M Slave Alone setting IP1 8 ALON SO A MAST SO M Master setting Alone setting Master setting M XX Mic sensitivity ON OFF Data reload V 1 0 V 9 9 Software version CH1 Color calibration CH2 Gobo calibration Focus calibration CH3 DMX MOD1 MOD2 16B mode 8B Mode Reset Wired mode REST ON OFF SIGL S1 S2 S3 Wireless Mode Wireless IN and wired OUT TXXX PAN 630 540 360 270 180 90 Termperature reading P
7. e cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is anormal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 01 122 129 Gobo 5 shake slow to fast 130 137 Gobo6 shake slow to fast 138 145 Gobo 7 shake slow to fast 146 153 Gobo 8 shake slow to fast 154 161 Gobo 9 shake slow to fast 162 169 Gobo 10 shake slow to fast 170 177 Gobo 11 shake slow to fast 178 185 Gobo 12 shake slow to fast 186 193 Gobo 13 shake slow to fast 194 201 Gobo 14 shake slow to fast 202 209 Gobo 15 shake slow to fast 210 217 Gobo 16 shake slow to fast 218 225 Gobo 17 shake slow to fast 226 255 Rot gobo wheel cont rotation slo
8. ight 6 8kg EE PHOTOMETRIC DATA BB Photometric Beam Angle Data 2 Beam Angle LUX x 0 0929 FC 6829 1828 7T44 461 114 99 FC 73510 19680 8010 4960 1230 1070 LUX M a 2 Om 2 5m 5m 7 5m 10m 15m 20m Beaneter 17 5 9335 350 267 109 144 cm 04 OPERATION INSTRUCTIONS The MINIBEAM 50 is for beam effect for on site decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using
9. lation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The MINIBEAM 50 provides a unique mounting bracket assembly that integrates the bottom of the base and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the Hanging Kit As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly Hanging Kit Satety Clamp Safety Cable Screw Turn around Turn around 06
10. uctions Should you need any spare parts please order genuine parts from your local dealer MINIBEANI 50 C W IP20 Le0 0 2mg te40 C t 150 C User Manual KEEP THIS MANUAL FOR FUTURE NEEDS EW SAFETY INSTRUCTIONS CAUTION Becareful with your operations With a dangerous voltage you cansuffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IMPORTANT Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of th
11. w to fast 0 31 Shutter closed 32 63 shutter open 64 95 Strobe effect slow to fast 7 Shutter 96 127 shutter open 128 159 Pulse effect in sequences slow to fast 160 191 shutter open 192 223 Random strobe effect slow to fast 224 255 shutter open 8 Dimmer 0 255 Dimmer 0 100 0 5 OFF 9 Prism 6 127 _ ON 128 191 Rrotating from slow to fast 0 225 max to min speed 10 Speed 226 235 blackout by movement pan tilt 236 245 blackout by all wheel changing 246 255 no function 0 19 No function 20 29 No function 30 39 No function 40 79 No function 80 84 All Motor reset 85 87 Scan motor reset 88 90 Colors motor reset 91 93 Gobo motor reset 11 Special 94 96 Shutter amp Dimmer motor reset function 97 99 Other motor reset 100 119 Internal program 1 120 139 Internal program 2 140 159 Internal program 3 160 179 Internal program 4 180 199 Internal program 5 200 219 Internal program 6 220 239 Internal program 7 240 255 Internal Sound program 1 10 EJ Dmx CHANNELS Mode Channel Function Values Description 16b 8b 1 1 Pan 0 255 PAN Movement 2 Pan fine 0 255 Fine control of Pan movement 3 2 Tilt 0 255 Tilt Movement 4 Tilt fine 0 255 Fine control of Tilt movement 0 7 Open white 8 15 Color 1 16 23 Color 2 24 31 Color 3 32 39 Color 4 40 47 Color 5 48 55 Color 6 5 3 Colorwheel 56 63 Color 7 64 71 Color 8 72 79 Color
Download Pdf Manuals
Related Search