User Manual
Contents
1. o Ground 5 5 3 G If you use a controller with a 5 pin DMX output connector you will need to use a 5 05 VG LM1083B 108pcs LED Moving Head Wash Light User Manual pin to 3 pin adapter The chart below details a proper cable conversion Conductor 3 Pin Female output 5 Pin Male Input Ground Pin 1 signal Pin 3 Do not use re Pin 4 Do not use Pin 5 VI INSTALLATION When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Screw clamp onto Insert quick lock fasteners Tighten quick lock the Omega holder into the installation holes fasteners fully clockwise Use safety cable for second protection 06 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Vil OPERATION Stand alone operation allows the fixture works without controller and be controlled by the control panel directly Please refer to the menu instruction Setting the first fixture to master device and the following devices to slave devices work in DMX mode then all devices will run synchronously Please refer to the menu instruction You can control the devices individually or synchronously by the DMX controller You should set the device s start address in the DMX menu by control panel2. After setting the address the device enter DMX mode Each fixture requires a start address from to 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that uses 4 DMX channels and was addressed to start on DMX channel 1 would read data from channels 1 2 3 4 Choose start addresses so that the channels used do not overlap and note the start address selected for future reference Note that Assign the same address to the different lightings they will receive the same signal Vil CHANNEL FUNCTION 07 VG LM1083B 108pcs LED Moving Head Wash Light User Manual CHANNEL CHANNEL VALUE CH5 Pan 000 255 000 225 Scan CH7 speed 220429 Pan 0 630degree or 0 540degree depending on the setting in menu O 270degree Natural speed fast If selected the Scan Black Out ON function in SET menu by control panel while DMX value is 226 236 the lighting blackout during pan tilt movement cus strobe 150 195 CH9 General 000 gt 225 General dimmer 0 100 005 031 032 lt 063 064 lt 095 096 lt gt 127 Rainbow CH10 effect 08 VG LM1083B 108pcs LED Moving Head Wash Light User Manual 128159 R t G O B 255 W min RGB 160 lt gt 191 R 4 G t B 255 W min RGB 192 lt 2223 R t G 255 B 255 W min RGB 224 lt 255 R 4 GC B 4 Wimin RGB O000 lt
3. 337 228 433mm Net weight 10kg NOTE Due to improvement the product specifications and this manual are subject to change without prior notice XI PHOTOMETRIC DATA Please keep this manual as a reference Thanks again for your business We truly appreciate it 16 17
4. 049 RGBW dimmer in operation CH1 4 050 lt 059 Red 060 lt 069 Green 070 lt 079 Blue 080 089 Yellow 090 gt 099 Cyan 100 lt 109 Pure white 110 119 Purple 120 lt 129 White 130 lt gt 139 Color temperature 3200K CH11 140 lt 149 150 159 160 lt 169 170 lt 179 180 189 Color temperature 5600K Color temperature 6500K Color temperature 8500K Color temperature 10000K Change Color The motors rotate automatically 190 lt 199 Change Color The motors controlled by controller 200 lt 209 Twinkling The motors rotate automatically 210 lt gt 219 Twinkling The motors controlled by controller 09 VG LM1083B 108pcs LED Moving Head Wash Light User Manual 230 lt gt 234 Fade The motors controlled by controller 2357 239 Auto macro The motors controlled by controller 240 lt 244 Sound macro The motors rotate automatically 245 lt 249 Sound macro The motors controlled by controller CH12 000 255 Pin eC hemmed CH13 000 255 Tie Meco bitmode IX CONTROL PANEL BUTTON FUNCTION Call the main menu or escape the current menu e return to the upper menu and give up the selected item or parameter Browse the menu item forward or increase the parameter DOWN Browse the menu item backward or decrease the parameter Confirm the selected item or parameter i e enter the next menu or escape the current menu and save the sele
5. VG LM1083B 108pcs LED Moving Head Wash Light User Manual VG LM1083B 108pcs LED Moving Head Wash Light User Manual LED Moving Head Wash Light VG LM1083B CE RoHS User Manual LLIPlease read this user manual before using this product Keep it for further reference VG LM1083B 108pcs LED Moving Head Wash Light User Manual INDEX La SAPBETY INFOR MATION ie 01 W MAINFEATFURES settee eect cece A 02 UU OV ER DEW oo 25 sen E cox sucvtasnsns sovun wes sevacensesscactecesatseheet 03 IWePOWER CONNECTION see ettr crete renee ear ne errors 03 Ne DAFA CONNECTION i recitsescenstcsh ntievsrssiserecnee 04 BUTANE AG ETAT OIN ies seers coe neoe meet catec ace E cee Reese 06 WAL OE RATION fee scenarios eee cok coe ere cece Me ice 07 VIN CHANNEL FUNCTION crncieerorsc crete ene eset ereacinni 07 De SCONTROL PANEL a scr vao cee a tueserueeeeetee west evagct eye 10 X MENU INSTRUCTION a ceeret were E conver necmnce 10 AI SPECIFICATION he a gies cree oreo gett ceuermettees rena mat eee 15 AFPHOTOMETRICDA TA a reenter nce ceca ne 16 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Thanks for using our product This device is a great and reliable unit that can meet most of your requirements for professional markets This product can be operated as a single unit or in multiple units for large applications This moving head has got the nice sculpt efficient save electricity and durable It is suitable for saloon disco hotel showplace studi
6. cted item or parameter X MENU INSTRUCTION Power on the fixture use UP or DOWN button could scroll all functions menu step by step as follow Addr 001 ManualDimmer Red Green Blue Yellow Cyan Purple PureWhite 10 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Press ENTER button if you wish to select one of them Press ECS button enter SET menu press again return SET menu ESC Addr 001 with actually stored address ENTER DMX menu UPt DOWN SET menue ESC ManualDimmer ENTER ManualDimmer menu UPt DOWN SET menu ESC Red ENTER null UPt DOWN SET menu ESC Green ENTER null UPt DOWN SET menue ESC Blue ENTER null UPt DOWN SET menu ESC Yellow ENTER null UPt DOWN SET menue ESC Cyan ENTER null UPt DOWN SET menu ESC Purple ENTER null UPt DOWN SET menu ESC PureWhite ENTER null UPt DOWN SET menu ESC White ENTER null UPt DOWN SET menu ESC 3200K ENTER null UPt DOWN SET menu ESC 5600K ENTER null UPt DOWN SET menu ESC 6500K ENTER null UPt DOWN SET menu ESC 8500K ENTER null UPt DOWN SET menu ESC 10000K ENTER null UPt DOWN SET menu ESC ChangeColor ENTER null UPt DOWN 11 VG LM1083B 108pcs LED Moving Head Wash Light User Manual SET menu ESC Twinkling ENTER null UPTt DOWN SET
7. der G Power supply H Control panel IV POWER CONNECTION 03 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Please ensure that the voltage matches the rated voltage and the device is always connected to the earth properly Depending on the application the lighting fixture may require a different connector Please refer to the below wire color code if installing a new connector Right connect of the power cables are as below Power Cable Connection Live wire Brown Blue Zero wire Yellow green Ground wire V DATA CONNECTION The fixtures may be connected via 3 Pin signal cables In DMX mode at the last fixture in the chain the DMX output has to connect with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals Controller termination plug 04 VG LM1083B 108pcs LED Moving Head Wash Light User Manual 1 Ground 2 Signal 2 Signal 3 Signal The termination plug is a male XLR plug with a 120 ohm 0 25 watt resistor soldered between pins 2 and 3 If you are making your own cables be sure to use standard two conductors shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split DMX512 OUT DMX512 IN 3 PIN XLR 3 PIN XLR
8. erials for example fabric wood paper at least 1 5 meters away from the light Keep flammable materials well away from the fixture Avoid looking directly into the light source especially those who suffer from epileptic fits When it is thunderstorm don t use the light and disconnect the power supply high voltage will destroy light Ifthe ambient temperature exceeds 35 C please do not use this light When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Verify that all screws are tightly fastened Il MAIN FEATURES Super bright 3 Watt LED long lifespan 100 000 hours Electronic strobe with pulse effects 11 or 13 standard DMX channels 3 control modes DMX 512 master slave mode sound activated mode Maximum Pan movement 540 or 630 self correcting Maximum Tilt movement 270 self correcting Electronic strobe with pulse effects 02 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Smooth electronic dimming make the light more colorful Onboard control panel and LCD graphic display I OVER VIEW D EFG A Carrying handle B Safety cable hole C Installation holes D DMX IN socket DMX OUT socket E Power switch F Fuse hol
9. menu ESC Fade ENTER null UPTt DOWN SET menu ESC Macro ENTER Macro menu UPTt DOWN The Menu functions provided are described in the following sections AOO1 with actually stored address __ DMX mode Press ENTER enter to the submenu DMX Menu DMX Address 001 Set the DMX address LNo DMX Signal Run 1f there is no DMX signal Stop Run Hold Run Auto Run LSound Run Manual Dimmer ManualDimmer Light Switch Hight ON LLight OFF Light Red 000 Red dimmer Light Green 000 Green dimmer Light Blue 000 gt Blue dimmer PureWhite 000 Pure White dimmer LLight White 000 White dimmer Light Strobe 000 Strobe adjustment Scan Pan 128 Pan movement with 8 Bit resolution Scan Tilt 128 Tilt movement with 8 Bit resolution Scan PanFine 000 Pan movement with 16 Bit resolution LScanTiltFine 000 Tilt movement with 16 Bit resolution 219 VG LM1083B 108pcs LED Moving Head Wash Light User Manual LT ight Calibrate Cal Red 15 16 Cal Green 15 16 Cal Blue 15 16 Cal White 15 16 Cal Pan 128 127 LCal Tilt 128 127 Red __ Static red Green __ Static green Blue __ Static blue Yellow __ Static yellow Cyan __ Static cyan Pure White __ Static Pure White White __ Static white White __ Static white 3200K __ 3200K color temperature 5600K __ 5600K color temperature 6500K __ 6500K color temperature 8500K __ 8500K color temperature 10000K __ 10000K color temperature Change C
10. o stage etc This product complies with the following standards TEC60598 1 2003 TEC60598 2 17 1984 A2 1990 Upon receiving products please check carefully that there has been no damage caused in transportation and that the following parts are enclosed VG LM1083B 108 LED Moving Head Washer Ipc User manual Ipc I SAFETY INFORMATION i Important All operation and maintenance must be carried out in accordance with this user manual Manufacturer will not with responsibility for those operations which not according to these Instructions Verify that the input voltage matches the rated voltage Always disconnect the power before attempting to open the equipment housing or carrying out any maintenance Do not connect power cable of other electric products with this unit e Make sure power socket is connected with earth cable well The earth cable of this unit is Yellow Green one Do not expose the fixture to rain or moisture 01 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Verify that the feed cables are undamaged and rated for the current requirements of all connected devices before use Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating Ensure that the air flow through fans and vents is free and unobstructed Keep all combustible mat
11. olor __ Change color program Twinkling __ Twinkling program Fade __ Fade program Macro __ Auto program enter can edit it Macro Menu Step Quantity 62 Program Step 01 Change Color Twinkling LFade LProgram Step 62 13 VG LM1083B 108pcs LED Moving Head Wash Light User Manual SET MENU SET Menu LReset Machine LReset ON LReset OFF LLoad Parameter LLoad ON LLoad OFF Master Alone Master Mode LAlone Mode Auto Sound S Auto Mode LSound Mode LMIC Sense 00 99 MIC sensitivity adjusting LTC Switch Reduce output if over temperature LTC Switch Mask LSwitch Mask ON LS witch Mask OFF LTC Switch Temp Pass word protected common user taboo LTC Temp Cap TC Temperature Capture LTC Temp Cap Yes LTC Temp Cap No LTC Temp Set TC Temperature set Scan Setting Reverse Pan Reverse Pan ON LReverse Pan OFF Reverse Tilt Reverse Tilt ON LReverse Tilt OFF 14 VG LM1083B 108pcs LED Moving Head Wash Light User Manual Scan 16 Bit 16 bit resolution Scan 16 Bit ON Scan 16 Bit OFF Pan Degree Pan Degree 630 630 LPan Degree 540 gt 540 LScan BlackOut Blackout during pan tilt movement LScanBlackOut ON ScanBlackOut OFF LFeed Back Return the head to the correct starting position Feed Back ON after changing the position LFeed Back OFF LInformation Information consultation LTime
12. tt mm ss LDate mm dd yy XI SPECIFICATION Electrical Power supply AC100 240V 50 60Hz Power consumption 400W Fuse 5A 5 20 Photometric data Light source 108 pcs 3W LEDs R 30 G 30 B 30 W 18 LED rated life 50 000 hours Beam angle 25degree Dynamic effects Color changing effects Can create excellent color mixing with high even and uniform distribution of brightness and light output Strobe Variable electronic strobe 0 25F P S Dimmer Variable electronic dimmer 0 100 Pan 540degree or 630degree 8 16 bit movement resolution automatic self correction 15 VG LM1083B 108pcs LED Moving Head Wash Light User Manual VG LM1083B 108pcs LED Moving Head Wash Light User Manual Tilt 270degree 8 16 bit movement resolution automatic self correction lux R 8400 2100 925 027 332 Other features Electronic strobe with pulse effects lux G 7532 1883 830 460 298 lux B 9480 2370 1015 576 354 O Oe lux W 10720 2680 1180 653 427 DMX channels 11 or 13 channels depend on 8 16 bit movement resolution UAN lux RGBW 35132 8933 3983 2158 1320 Protocols DMX 512 Operation modes DMX mode Master Slave mode Sound Activated mode Construction e1 Cc Color Black D 5 Housing ABS Protection rating IP20 g1 Thermal a 2 Working temperature 20 C 35 C DISTANCE m 0 2 4 6 8 10 Thermostat Built in thermostat for overheating protection DIAMETER m 0 0 52 1 05 1 58 2 10 2 63 Physical Fixture dimensions
Download Pdf Manuals
Related Search