UM 7206™ - UK Automation
Contents
1. The Marmitek X 10 System is based on power line communication The range of the Marmitek X 10 signals very much depends on the local circumstances On average the range is a cable length of 80 meters If you have difficulties with the range of your Marmitek X 10 signals please pay attention to the following facts 1 When more than one phase is used for your electrical system it is necessary to couple these phases for the Marmitek X 10 signals For coupling you can use FD10 Phase Couplers Filters You only need to install a Phase Coupler Filter when your wall outlets and light switches are divided over more than one phase more than one group is no problem For bigger buildings or longer distances we advice you to use an active repeater instead of passive FD10 s 2 It is possible that Marmitek X 10 signals are attenuated by devices and lights which are connected to the power line In a normal home situation this effect is negligible the Marmitek X 10 system is using active gain control to eliminate the effects However it is possible that a particular device in your house is attenuating the signals so much that the range of Marmitek X 10 signals is decreased significantly When you have range problems it is wise to try to locate the device which is attenuating the signals simply by unplugging devices from the power line and testing the differences in range for your Marmitek system When e g your conclusion is that e g your computer monitor2. is attenuating the signal you can use a FM10 Plug in Filter between the power line and the monitor to eliminate the effects Knovvn devices which can cause attenuation are PC Monitors PCs with heavy internal power supplies Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps Energy Saving Lamps 3 Some old devices are able to disturb the signal by transmitting noise on the power line Because the Marmitek X 10 signals are transmitted on 120 kHz only noise on or near this freguency will have influence on the range When you use a FM10 Filter to connect this device to the power line the noise will be filtered 4 The Marmitek X 10 protocol has several mechanism to avoid modules to be switched on or off by other sources than your Marmitek X 10 Controllers However it is possible that 4 MARMITEK the Marmitek X 10 signals are disturbed by e g baby phones which are in TALK mode continuous transmission When these kind of signals are present on the power line it is possible that the Marmitek X 10 signals will not come through 5 The mains do not stop at the front door of your home Everything that is attached to mains nearby your home can have influence on Marmitek X 10 signals e g heavy machinery If you think that your system is influenced by devices out of your house it is advisable to install FD10 Phase Coupler Filter on each phase entering the house These filters will block signals coming into or going out
3. of your house but will also match the impedance for the mains Hereby make your house Marmitek X 10 compatible for these units The FD10 s will not only filter but will also couple the phases please see 1 INSTRUCTIONS FOR USE INTRODUCTION Thank you for buying a Marmitek X 10 UM7206 universal receiver The UM7206 provides the link between low voltage appliances and the Marmitek X 10 system The UM7206 module receives the X 10 signal via the lighting circuit and switches lights and 24 V DC appliances with a current up to 5 A The UM7206 can be set to pulse or continuous contact and can be controlled remotely with the Marmitek X 10 commands ON and OFF The UM7206 is manually operated via two keys ON on test and OFF The UM7206 also has a built in buzzer that produces a sound when the module receives an ON signal The buzzer can if preferred be deactivated If the unit is set to pulse switching with sound the built in buzzer will produce three to four high pitched bleeps The module is powered and controlled via the 230V lighting circuit and is fitted with a mains power lead INSTALLATION The module is easy to install Connect the low voltage appliance to the two potential free dead contacts screw connectors and then set the address After connecting the plug to the mains the module can be operated both locally and remotely Using a small screwdriver set the desired address e g A1 Connect the low voltage appliance
4. to the screw terminals max 24 V DC 5 A Activate the UM7206 by connecting the plug to the mains Adjust the sliding switches to the preferred positions Sliding switch Left 1 Continuous The module switches on when it receives an ON command and off when it receives an OFF command 2 Momentary The module switches on for 3 5 seconds after receiving an ON command and then switches off again Sliding switch Right 1 Sounder Only Only audio signal 2 Sounder amp Relay Audio signal and relay contact 3 Relay Only Only relay contact BUN UM7206 5 FREOENTLY ASKED OUESTIONS What is the reason for modules to switch on off spontaneously It is possible that a Marmitek X 10 System is installed at one of your neighbours using the same House Code To solve this problem try to change the House Code of your system or have FD10 Phase Coupler Filter installed at your incoming mains My modules will not respond to my controller Make sure that the House Code on all Modules and Controllers are set to the same House Code A P My modules will not react to my remote sensor When you use a remote or sensor you should have at least one TM13 Transceiver or Marmitek X 10 Security Console installed in your house These components will translate the radio signals to the Marmitek X 10 signal on the power line Using several remotes and sensors you only need one central transceiver Am able to increase the range of my re
5. UM7206 UNIVERSAL RECEIVER 20148 20061012 UM7206 UNIVERSAL RECEIVER MARMI l EK ALL RIGHTS RESERVED MARMITEK 2007 MARMITEK UM7206 UNIVERSAL RECEIVER SAFETY WARNINGS To prevent short circuits this product should only be used inside and only in dry spaces Do not expose the components to rain or moisture Do not use the product close to a bath swimming pool etc Do not expose the components of your systems to extremely high temperatures or bright light sources Do not open the product the device may contain live parts The product should only be repaired or serviced by a qualified repairman In case of improper usage or if you have opened altered and repaired the product yourself all guarantees expire Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified Marmitek does not accept responsibility for additional damage other than covered by the legal product responsibility This product is not a toy Keep out of reach of children Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on the identification tags Never connect an adapter or power cord when it is damaged In that case contact your supplier Automatic switching devices provide comfort but can also be dangerous They can surprise people or can ignite clothing hanging over an electric heat source Please be c
6. areful and take appropriate measures to avoid accidents HOW DOES MARMITEK X 10 WORK Marmitek X 10 components use the existing mains wiring to communicate using Marmitek X 10 signals You can build a complete system using the three different kind of components of the Marmitek X 10 System 1 Modules These components will receive Marmitek X 10 signals and will switch or dim the attached lamp or appliance 2 Controllers These components will transmit Marmitek X 10 signals and thus will control the Modules 3 Transmitters Wireless components like remotes The signals of these components will be received by a controller with transceiver functionality IRRF 7243 TM13 or console of a Marmitek Security System The Transceiver will translate the signals into Marmitek X 10 signals on the power line ADRESSES Up to a maximum of 256 different addresses can be preset These are subdivided into a so called HouseCode A to P incl and a UnitCode 1 to 16 incl The HouseCode can also be set on the controllers so that the controllers and modules become part of the same system The address can be set either using code dials or by pressing buttons depending on the type of module UM7206 The Marmitek X 10 System uses standard commands which control all units with the same HouseCode at the same time e g all lights on all off etc SIGNAL RANGE Range of Marmitek X 10 signals over the Power Line and how to increase the range
7. motes by using more Transceivers Yes you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting TM13 s will wait for a quite power line before transmitting their data To prevent your Marmitek X 10 System to become slow or to prevent dimming from becoming less smooth make sure that the TM13 units are placed as far away from each other as possible What is the maximum load on connections on the UM7206 module e Without additional protective housing maximum 24 VDC 5A e With a protective housing which removes all risks of electric shocks maximum load 230 VAC 500mA Do you still have questions Please check out www marmitek com for more information TECHNICAL SPECIFICATIONS Power supply 230VAC 50 Hz Power consumption lt 20 mA capacitive Switching power 5A at 24 VDC Signal sensitivity 15 mVpp min 50mVpp max at 120 kHz Input impedance gt 55 Ohm P N at 120 kHz Responds to X 10 Key codes On Off Connectors 2 x screw connector Ambient temperature 10 C to 50 C operation 20 C to 70 C storage Dimensions 55x90x38mm 6 MARMITEK Environmental Information for Customers in the European Union European Directive 2002 96 EC reguires that the eguipment bearing this symbol on the product and or its packaging must not be disposed of with unsorted mu
8. nicipal waste The symbol indicates that this product should EEE be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product UM7206 7
Download Pdf Manuals
Related Search