Home

DISCO-500G

1. and X Y on the back of the laser have to be down You can now operate the laser with ILDA Use this switch setting only when connected to an ILDA controller Even if you disconnect interrupt the IDLA connection only for a short period always put the switches into up position or turn the device off You can now control laser output with a PC using for example our ShowEditor 2006 software Laserworld offers a variety of music synchronous lasershows for ShowEditor 2006 USER MANUAL DISCO 500G Page 8 of 9 7 MAINTENANCE Maintenance should be performed every 15 day period by using a sponge which is dipped with alcohol rather than wet cloth or other chemical liquid to clean the mirror Always disconnect from the mains when the device is not in use or before cleaning it There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Never look directly into the light source Always disconnect from the mains when the device is not in use or before cleaning it 8 TECHNICAL SPECIFICATIONS Power supply AC 220V 240V 50 60 Hz DMX 512 11 channels Ambient temperature 10 C 35 C Power consumption 40 W Working mode automatic music active DMX512 ILDA Optical power ca 500mW 532nm Laser classification 4 Weight 4 kg Dimensions 300 x 240 x 130 mm PLEASE NOTE This device has left our premises in absolutely perfect condition
2. DISCO 500G USER MANUAL USER MANUAL DISCO 500G I Table of contents 1 SAFETY INSTRUCTIONS 2 OPERATING DETERMINATIONS 3 OPERATION 4 AUTO MUSIC MODE 5 OPERATION WITH DMX 6 ILDA OPERATION 7 MAINTENANCE 8 TECHNICAL SPECIFICATIONS Checking Parts Please check if the following parts are included 1 x DISCO 500G 1 x Power cable 1 x DMX cable 1 x ILDA adaptor 1 x User manual Page 2 of 9 Page USER MANUAL DISCO 500G Page 3 of 9 DANGER LASER RADIATION Avoid direct eye exposure Laser radiation can cause eye damage and or skin damage All protective measures for a safe operation of this laser must be applied 1 SAFETY INSTRUCTIONS If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature 1 The laser must only be used for shows The operation is only allowed if it is controlled by a skilled and well trained operator Never leave this device running unattended and keep it away from children and unauthorized persons 2 Keep away from heaters and other heating sources In order to safeguard sufficient ventilation leave 50 cm of free space around the device 3 Never direct the laser beam to people or animals 4 CAUTION LASER DIODE Never unscrew the housing There are no serviceable parts inside the device M
3. In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Laserworld cannot be made liable for damages caused by incorrect installations and unskilled operation USER MANUAL DISCO 500G Page 9 of 9 EU Declaration of Conformity 4 We hereby confirm that the following device DISCO 500G complies with the essential safety requirements laid down in the regulations of the committee to assimilate the provisions of law of all participating EU states on the electromagnetic compatibility 98 336 EWG The device has been classified considering the following EU norms on electromagnetic compatibility DIN EN 55103 1 1996 DIN EN 55103 2 1996 DIN EN 61000 3 2 2000 A2 2005 DIN EN 61000 3 3 1995 A1 2001 Assessment of compliance of the product with the requirements relating to the Low Voltage Directive LVD was based on the following standards DIN EN 60065 2002 Furthermore the device is verified in correspondence to the laser class regulations DIN EN 60825 1 if properly set up according to the upper mentioned laser safety regulation After installing the device an inspection and official approval is indispensable for the overall setup The inspection must follow the european guidelines EN 60825 1 and corresponding regulations for the prevention of accidents BGV B2 This declaration is executed on
4. adress USER MANUAL DISCO 500G Page 6 of 9 The device uses 11 channels so if you set the first on DMX address 1 the second should be DMX address 12 and so on The DMX channels are as following Mode 0 69 laser off 70 139 sound mode 140 209 animated sound mode see above 210 255 DMX mode Effect channel Strobe Horizontal movement 0 no effect 1 167 fixed movement 168 188 animated movement left to right with increasing speed 189 209 do Right to left 210 255 do left to right and back Vertical movement analogous to hor movem Zoom 0 10 no effect 11 104 increasing size 105 154 growing with increasing speed 155 204 do shrinking 205 255 do growing shrinking Width rotation about y 0 150 fixed rotation 151 255 automatic rotation with incr speed Height rot About X analogous to width Rotation 0 180 fixed rotation 181 217 automatic with incr speed clockwise 218 255 do counter clockwise Blanking 0 70 no effect 71 139 points are brighter 140 209 dashed lines 210 255 points only Please note that according to the pattern not all effect channels are activated E g you can t zoom dynamic patterns etc Channel 3 strobe is also available when in soundmode channel 1 70 209 USER MANUAL DISCO 500G Page 7 of 9 6 ILDA OPERATION Connect the laser to an ILDA output as our USB box using the adaptor shipped with the device switches BLANKING
5. aintenance and service operations shall only be carried out by authorized dealers 5 Always disconnect from the mains when the device is not in use or before cleaning it HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock USER MANUAL DISCO 500G Page 4 of 9 2 OPERATING DETERMINATIONS 6 The operator has to make sure that laser radiation also reflected laser radiation higher than the highest allowed level is avoided by technical or organisational measures 7 Make sure that the used voltage is AC 220V 240V 50 60Hz 8 If the device is used in a flying installation the mounting brackets and an appropriate safety rope must be fixed 9 Laser effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects 10 In some countries the operator must notify the accidence insurance and the authority for industrial safety before operating a laser For more information contact the relevant authorities 11 Please consider that unauthorized modifications on the device are forbidden due to safety reasons 12 If this device will be operated in any way differently than described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc 13 When the laser is not at
6. behalf of the DISCO 500G Laser manufacturer Laserworld Switzerland AG Oberstrasse 1 8274 T gerwilen SWITZERLAND Authorized person Supervisory board Ms Rhea G ssel place of business 8274 T gerwilen SWITZERLAND company number CH 440 3 020 548 6 Commercial Registry Kanton Thurgau www laserworld com infoOlaserworld com representative according to EMVG Cleantech Europe GmbH Managing Director Thomas Schulze F rkhofstr 5 81927 M nchen DE
7. tached to an ILDA output device even for a short period switch ILDA mode off see below or turn the device off USER MANUAL DISCO 500G Page 5 of 9 3 OPERATION Please note for sound DMX mode the two switches on the back of the device labelled BLANKING and X Y have to be up When both switches are down the device can be controlled by an ILDA output such as our USB Box Use this switch setting only when connected to such an ILDA controller Even if you disconnect interrupt the ILDA connection only for a short period always put the switches into up position or turn the device off 4 AUTO MUSIC MODE If you put switch 10 to ON the patterns will change automatically and are animated by sound sound or music mode the switches labelled BLANKING and X Y have to be up You can control the music sensitivity of the microphone with the min max knob on the rear panel With switch 1 you can select two modes standard sound mode patterns will move triggered by sound and animated sound mode patterns will move slowly without sound and will be accelerated with sound 5 OPERATION WITH DMX If you turn switch 10 to OFF and switches BLANKING and X Y up the device is in DMX mode Set the DMX address and connect the device to a DMX controller you can then operate you CS 200G ECO with DMX Set the DMX address code with the binary system 0 or 17 A few examples DMX DMX adress

DISCO-500G

Contents

Download Pdf Manuals

Related Search

Related Contents