AdvanceMobile User Manual
Contents
1. 11 F Emergency PTT The RED Emergency PTT is available as an optional extra 1 To attach the Emergency PTT to the gear lever strap the PTT around the gear lever using the Velcro strip attached with the cord facing down y Velcro Strip Flat Plastic Diagram 8 2 To attach the Emergency PTT to a flat surface remove the 2 screws from the bottom of the PTT which holds the Velcro strip in place Remove the strips and replace the small plastic part that held the strips in place with the larger flat plastic part supplied with the PTT Screw the new plastic part in place 3 Feed the cable out of sight to the location where you intend to mount the 4 pin connector on the junction box Caution Make sure there is sufficient slack in the cable to allow the free movement of the gear lever without stretching the PTT cable Inserting SIM into Junction Box 1 Open the SIM door cover on the bottom of the junction box by removing the screw holding it shut Screw Diagram 9 2 Slide the metal SIM cover to the left and lift the cover 12 Diagram 10 3 Insert the SIM card under the metal cover and close the metal cover and slide to the right to lock Diagram 11 4 Replace the plastic SIM cover and screw it closed NOTE The SIM card can not be inserted or removed while the Junction Box is powered To remove or replace the SIM card after installation has been completed the power cable must be disconnected from the2. ACVANCEIEC INDUSTRIES INC INC f AdvanceMobile Installation User Manual Part No AT3550A a oe AdvanceTec Industries Inc 1150 NW 163 Drive Miami FL 33169 T 305 623 3939 F 305 623 3996 Toll Free 1 800 881 8211 Company web site www advancetec com GPS services www advancemobilegps com gt Q gt 4 5 8 10 10 10 11 11 12 12 13 14 14 14 Description Part numbers and installation guides Installation Warnings Installation of Speaker Installation of PTT Installation of Microphone Installation of Power Cable Installation of Vehicular and GPS Antenna Installation of Emergency PTT Inserting SIM into Junction Box Connecting Cables to Junction Box System Registration and Programming Making and receiving PTT call Receiving incoming Cellular call Turning AdvanceMobile OFF Optional Extra Accessories 15 17 18 19 Specifications 20 22 AdvanceMobile Control Modules Privacy Handset with Cradle Palm Mic Specifications The AdvanceTec AdvanceMobile is designed to provide secure and convenient vehicular communication with GPS tracking if needed The AdvanceMobile consists of 1 Part AT8246A Junction Box 2 Part AT8231A Speaker 3 Part AT8230A Visor Microphone Visor Mic 4 Part AT8232A Power cable 5 Part AT9299B Push To Talk PTT 6 Part AT8407A Antenna Magnet Mount Mag Mount Optional Extra
3. Program 1 Attach the connector at the end of the cable of the Control Module to the corresponding connector on the AdvanceMobile junction box 2 With the AdvanceMobile powered press the UP or DOWN Channel Control Button Channel numbers from 1 to 9 will show in the Control Module screen Channel number 0 will show E and is used for an Emergency number 3 A flashing number in the screen indicates that the channel is open not programmed and available to be programmed 4 With a channel number flashing initiate a PTT call to the AdvanceMobile from the phone with a Private ID that you want the AdvanceMobile to communicate Keep the PTT button pressed 5 When the incoming PTT call is heard on the AdvanceMobile speaker with the PTT button still pressed press in the programming button next to the SIM flap by using a pen refill or similar devise 17 Diagram 15 NOTE Both the PTT and the Programming button must be kept depressed until the programming has been successfully completed and the 5 fast beeps are heard on the speaker 5 Once the new private ID is successfully programmed the channel number in the screen will no longer flash 6 This process can be repeated with the other open channels until each of the 9 channels are programmed with different private IDs Operation 1 Select a channel by pressing the Left Channel Keys Up and Down If the Display shows a steady number 1 9 the channel display
4. directly to the chassis of the vehicle 6 If the connection is being made in the engine compartment connect the in line fuse holder between the black lead of the power cable and the desired chassis connection point Note Do not connect the black lead to the negative battery terminal The AdvanceMobile could be damaged if there were a malfunction in the vehicle s electrical system 7 Cut the red lead to the desired length This lead will be connected such that it has positive supply voltage at all times even when the vehicle is turned off 8 If the connection is being made under the dash or in the vehicle cabin connect the red lead to a positive supply voltage point 9 If the connection is being made in the engine compartment or directly to the battery connect the in line fuse holder between the red lead of the power cable and the desired positive voltage connection point 10 Route and connect the green lead to a convenient ignition switch supply point in the vehicle Note an ignition switch accessory terminal can be verified by measuring the terminal while operating the vehicle s key switch With the ignition key in the accessory ON position the terminal voltage should measure the vehicle s battery voltage With the switch in the OFF position it should measure near zero Stereo Mute If the vehicle s stereo system supports an external muting feature route and connects the orange wire to the car ster
5. C A code Channels 12 channel simultaneous operation Update rate 1Hz Accuracy Horizontal lt 3 meters 50 lt 8 meters 90 Altitude lt 16 meters 50 lt 16 meters 90 Velocity 0 06 m sec PPS 50 nanoseconds Acquisition Reacquisition 2 sec Hot Start 9 sec Warm Start 35 sec Cold Start TTFF 39 sec Out of the box 41 sec GPS Antenna Connection SMA Sub Miniature A connection with a male center contact Use this contact for the GPS Antenna provided with the unit 50 Ohms impedance 23 GPS Antenna Spec Patch Center Frequency 1575 42 1 023 MHz when covered with a radome and measured by LNA ground plane Bandwidth 10dB return loss 10 MHz min Gain at Zenith 1dB type Gain ay 10 elevation 5 dBic type Polarization R H C P Axial Ratio 5 0 dB type Filter LNA Center Frequency 1575 42 1 023 MHz Gain 30 37 dB pc 3V 32dB Noise Figure 1 4 dB type ps 3V 1 35 dB Filer out band attenuation Dielectric filter 7dB min fo 20 MHz 20dB min fot50MHz 30dB Min fo 100MHz fo 1575 42MHz Output V S W R 2 0 max Voltage DC 2 5 5 5V Current DC 8 23mA ps 3V 10mA iDEN antenna connector Mini USB connector with a female center contact Use this connector for the iDEN Antenna provided with the unit 50 Ohms impedance Environmental Specifications Operational Temperature 20 to 60 C Storage Temperature 40 to 85 C Shock MIL STD 810E METHOD 516 4 Proc 1 18 sh
6. Junction Box Connecting cables to Junction Box 1 Locate a position for the junction box beneath the dashboard on the pas senger s side of the vehicle or on the center side post between the front seats It must be protected from dirt and moisture and must be afforded adequate space for cooling There must be sufficient space to allow for connection of all cabling 13 2 DO NOT mount the junction box at this stage Connect the PTT Microphone Speaker Power cable and to their corresponding connections on the Junction Box as indicated in Diagram below Mic Speaker PTT Optional Optional Power Control Module Palm Mic Handset w Cradle Diagram 8 3 Connect the coaxial antenna cable to the corresponding connector on the opposite side of the Junction Box 4 After connecting the power cable s connector to the Junction Box cut in half the red wire attached to the fuse housing supplied Cut the long red power lead to the desired length and connect crimp it to the one end of the wire to the fuse housing 5 Connect the other end of the wire from the red fuse housing to the positive side of the ignition The fuse housing can be secured in place by using a plastic tie or screw through the hole in the fuse s plastic housing System Registration and Programming 1 Once the AdvanceMobile is powered and the SIM is inserted it will begin the registration process onto the iDEN system The initial registration onto the iDEN syst
7. K Blinking Green Unit registered OK and Ignition is off The Unit is about to shut off Steady Green amp Red Amber PTT is in operation Alternating Green amp Red Data is transmitting for GPS 19 Privacy Handset Part AT7107A Diagram 16 1 PTT calls can be made and PTT and cellular calls can be received in the same way with the Privacy Handset as with the PTT described above 2 Lift the privacy handset out of the cradle and using the PTT button on the back of the privacy handset follow the instructions for making and receiving calls as set out above 3 A cellular call can be terminated by pressing and holding down the PTT button 20 Palm_Mic Part AT8410A Diagram 17 1 To use a Palm Mic with the AdvanceMobile plug the connector on the end of the coil cord of the Palm Mic into the corresponding RJ45 receptacle on Junction Box 2 Once connected the pressing of the switch on the Palm Mic will deactivate the Visor Mic and activate the Palm Mic 21 Specifications Input Output Input voltage 10 5Vdc to 32V dc Ignition detection Ignition ON 2 5Vdc to 32Vdc Ignition OFF OV to 2 5V or OPEN Outputs Entertainment Mute Open Drain Continuous current capacity 50Ma Audio Specifications RJ45 Supports Palm MIC AT8410A and Privacy Handset Part AT7107A 2 5mm Stereo audio jack Speaker impedance 4 Ohms 10W Microphone Eco Canceling Noise Canceling Communication Specif
8. SIM card contact your local IDEN Provider sales representative or retail store Installation of AdvanceMobile A Speaker Installation 1 Mount the Speaker beneath the dashboard on the passenger s side of the vehicle out of the way of the passenger Do not mount the Speaker on the dashboard or the rear window shelf 2 The Speaker should be located more than four feet from the junction box 3 The Speaker includes a mounting bracket permitting it to be mounted in a variety of ways Loosen the thumbscrews on the side of the speaker and using the mounting bracket as a template drill the necessary mounting holes and secure the bracket with the self tapping screws provided Thumb Screws Diagram 1 4 Position the Speaker on the mounting bracket and secure it by tightening the thumbscrews The mounting bracket is used to permanently mount the Speaker in place while permitting it to be tilted to a desired angle 5 Feed the cable out of sight to the location where you intend to mount the junction box 6 The speaker should be located at least 3 ft 1m from the visor mic Avoid placing the speaker where it faces the visor microphone B Mounting of the PTT 1 To attach the PTT to the gear lever strap the PTT around the gear lever using the Velcro strip attached with the cord facing down Velcro Strip Waaa _ _ Flat Plastic Diagram 2 7 2 To attach the PTT to a flat surface remove the 2 screws from t
9. e press and hold down the PTT button 2 Speak towards the visor microphone 3 To respond to an incoming PTT call that is NOT from the Private ID or Group programmed into the AdvanceMobile press and hold down the PTT button within 15 seconds of the receipt of the PTT call 4 Speak towards the visor microphone Incoming Cellular call 1 To answer an incoming cellular call press and hold the PTT button for 3 seconds Once the incoming call is answered release the PTT to continue the cellular conversation 3 Speak towards the visor microphone 4 To end the cellular call press and hold down the PTT Turning AdvanceMobile OFF 1 When the car ignition is ON the AdvanceMobile will stay on 2 When the ignition is turned OFF and there is no active call or dispatch in progress the AdvanceMobile will turn OFF after 30 seconds 3 The AdvanceMobile will remain on if an active call or dispatch is in progress even if the ignition is turned OFF gt 16 Optional Extra Accessories AdvanceMobile Control Module Part AT3510A The AdvanceMobile control module Control Module is an optional extra which will enhance the features and functions of the AdvanceMobile With the addition of the Control Module PTT calls from the AdvanceMobile can be increased from a single Private ID or Group ID to a Group ID and 9 different Private IDs Volume Control Channel Control Buttons Buttons Diagram 14
10. e AdvanceMobile should be used with a negative ground electrical system only Reverse polarity positive ground will trigger protection circuits which cause the cable fuse to open Check the ground polarity before you begin the installation to prevent wasted time and effort 12V DC or 24V DC automotive systems are directly supported Determine the best cable route to the vehicle ignition for the Power Cable from the location where you intend to mount the Junction Box Diagram 4 1 The DC power cable shipped with the AdvanceMobile is suitable for installation in most vehicles 2 Route the black lead of the main power cable to a convenient chassis ground and the red lead to the positive supply voltage connection points If it is necessary to penetrate the firewall try to use an existing opening 3 If there is no existing opening drill a new hole approximately 9 16 or 3 5cm in diameter Make sure that there is enough clearance on the opposite side Insert a grommet into the hole to prevent damage to the power cable When making connections on the engine side of the firewall additional in line fuse holder included should be used at the connection points Green To Ignition Switch Orange To Vehicle Stereo Black To Vehicle Chassis Groud Red To Vehicle Supply Voltage Diagram 5 4 Cut the black lead to the desired length 5 If the connection is being made under the dash or in the vehicle cabin connect the black lead
11. ed is the channel selected and programmed When the PTT is pressed it will transmit on that channel 2 If the Display shows a slow flashing number 1 9 the channel is not programmed If the PTT is pressed a reject tone will be heard 3 If the Display shows a fast flashing number 1 9 a call is coming in from the remote user who is programmed into the AdvanceMobile on that channel number Press the PTT to answer the incoming caller 4 lf the Display shows a fast flashing U a call is coming in from an unknown remote user who is not programmed into the AdvanceMobile Press the PTT to answer the incoming caller 5 If the Display shows fast flashing E a call is coming in from a remote user programmed as an Emergency number 18 6 Adjust the volume by pressing the Right Volume Buttons Up or Down After a volume button is pressed a blinking dot will appear in the bottom right corner of the screen to indicate that it is in the volume mode The Minimum volume is 0 and the Maximum is 5 After the volume has been adjusted the blinking dot will disappear to indicate that the unit is back in the channel mode 7 The Channel and Volume selected will be saved when the Control Module is powered off and will resume when it is next powered up 8 If the Control Module looses communication with the main unit it will show 3 horizontal lines LED indicators Flashing red Unit not yet registered Steady Green Unit registered O
12. em can take up to 3 minutes 2 Once the AdvanceMobile has successfully registered onto the iDEN system 5 short pulses will be heard through the speaker 3 After registration the Private ID or Group ID with which the AdvanceMobile will communicate must be loaded into the AdvanceMobile 4 To program the Private ID or Group ID initiate a PTT call to the AdvanceMobile from the phone with the Private ID or a phone that is part of a Group ID with which you want the AdvanceMobile to communicate Keep the PTT button pressed 5 When the incoming PTT call is heard on the AdvanceMobile speaker with the PTT button still pressed press in the programming button next to the SIM flap by using a pen refill or similar devise 14 NOTE Both the PTT and the Programming button must be kept depressed until the programming has been successfully completed and the 5 fast beeps are heard on the speaker Diagram 12 3 Once the Private ID or Group ID has been successfully loaded proceed to permanently mount the junction box with the screws provided ensuring that all extra cabling is secured out of harms way Mounting holes lt Mounting holes Diagram 13 Making a PTT call to Private ID or Group ID programmed 1 Press and hold down the PTT button 2 Speak towards the visor microphone 15 Incoming PTT 1 To respond to an incoming PTT call that is from the PTT Private ID or Group programmed into the AdvanceMobil
13. eo system Otherwise the orange wire may be left unconnected and cut off or tied out of the way Note The car Kit supports an Entertainment Mute function when connected to a car stereo system that provides for external muting This function is compatible with systems that mute the audio output when the control line is connected to ground E Mount the Vehicular Antenna amp GPS Antenna 1 Screw the antenna to the external magnetic Mag mount antenna base 2 Mount the Mag Mount antenna or other external vehicular antenna to be purchased separately if the supplied Mag Mount Antenna does not fit your purposes For best performance use a low loss coaxial cable with the highest gain antenna 10 3 Position the antenna maintaining a separation distance of at least 8 inches 20 cms between the antenna and the body of any user and nearby person to assure compliance with the U S FCC regulations on RF exposure GPS Antenna External Antenna Diagram 6 4 Connect the antenna cable to the external antenna connector on the junction box GPS USB Emergency External Antenna Data Output PTT Antennas Diagram 7 5 If you intend to make use of the GPS feature connect the GPS antenna cable to the GPS antenna connector on the junction box The GPS antenna is an optional extra that is available to be purchased from AdvanceTec 6 Feed the antenna cables out of sight to the location where you intend to mount the junction box
14. he bottom of the PTT which holds the Velcro strip in place Remove the strips and replace the small plastic part that held the strips in place with the larger flat plastic part supplied with the PTT Screw the new plastic part in place 3 Feed the cable out of sight to the location where you intend to mount the junction box Caution Make sure there is sufficient slack in the cable to allow the free movement of the gear lever without stretching the PTT cable C Mounting the Microphone Selecting the correct position for the microphone is vital for the successful performance of the AdvanceMobile 1 The Microphone should be mounted either on the sun visor directly above and facing the driver or on the headliner just above and facing the driver One of the following two microphones will be supplied with this kit Ai Facing the driver Diagram 3 2 The microphone supplied has a noise canceling feature so must be mounted facing the driver as shown in the picture above 3 To avoid visual or physical obstruction route the microphone cable down inside the door molding Allow sufficient slack in the connector end of the cable to reach the Junction Box 4 Feed the cable to the location where you intend to mount the junction box Note The microphone should not be mounted near a window or in a spot where road and ambient background noise would be substantially high above 85dB SPL D Installing the Power Cable Caution Th
15. ications Full Duplex Communication Automatic Start up Antenna Impedance 50 Ohms SIM card 3 Volts SIM cars PIN Programmed by user one time automatically introduced Onward PIN saved on Non Volatile memory Receiver Specifications Frequency Range 851 min 870 MHz Max in the 800MHz band Frequency Range 935 min 941 MHz max in the 900MHz band Channel Spacing 25 N A KHz Sensitivity 10 BER 111dBm max Strong Signal BER 0 1 max RF level 80 dBm Overload Immunity 10 max on channel _20dBm Intermodulation Immunity 45 dBm min Far out interferers On cannel 108dBm Adjacent Channel Immunity 51 dBm min Spurious Response Immunity 51 dBm min Stability unlocked 5 ppm max Stability unlocked 1 9 ppm max Spurious Emissions per FCC requirements 3m 22 Conducted 57 dBm Radiated 500 uV m Transient Response 0 01 BER during RX TXRX Frequency Acquisition 0 01 max 220 Hz RF input Blocking Immunity 10 max Transmitter Specifications Frequency Range min 806 max 825 MHz band Frequency Range min 896 max 900 MHz band Channel spacing 25 KHz Power 0 44W min 0 7W max Pulse average power basic Terminal class TX BER 0 7 max ACCPR 25 KHz 60 dB min Frequent Stability 5 ppm max Unblocked to base Spurious Emissions 13dBm max per FCC and IPU R requirements IDEN GPS Specifications GPS Module Sensitivity 152 dBm Tracking 142 dBm Acquisition Protocol TAIP ASCII Frequency L1 type 1575 42 MHz
16. luding communications equipment in the area over the air bag or in the air bag deployment area If the communication equipment is improperly installed and the air bag inflates this could cause serious injury 5 It is recommended that the installation of the vehicle communication equipment be performed by a professional installer technician trained in the requirements for such installations An air bag s size shape and deployment area can vary by vehicle make model and front compartment configuration for example bench seat vs bucket seats Contact the vehicle manufacturer s corporate headquarters if necessary for specific air bag information for the vehicle make model and front compartment configuration involved in your communication equipment installation WARNING VEHICLES WITH ANTI SKID BRAKING SYSTEMS For vehicles with electronic anti skid braking systems refer to the Anti Skid Braking Precautions Motorola publication 68P81109E34 This publication can be ordered from Motorola Worldwide Systems and Aftermarket Parts Department Operating the AdvanceMobile The AdvanceMobile will allow 1 PTT calls from the unit to a pre set private ID or group ID 2 PTT and Cellular calls to the unit 3 When used with the Optional Control Module PTT calls from the unit to a Group ID and 9 different Private ID numbers Set up of AdvanceMobile NOTE The AdvanceMobile requires an IDEN SIM card To acquire such a
17. ocks 40 G half sine 6 9 msec 18 Shocks 2500g s 0 00075 second pulse Vibration 2X ElA not tested electronically during vibration Sine 20 2000 Hz 4G peak 1 hr per axis 3 axis X y z Random 20 2000 Hz 6G RMS 1 hr per axis axis xX y Z 24 AdvanceMobile GPS services ACVANCE INDUSTRIES INC GPS MONITORING SYSTEM www advancemobilegps com INDUSTRIES INC AdvanceTec Industries Inc 1150 NW 163 Drive Miami FL 33169 Tel 305 623 3939 Toll Free 1 800 881 8211 www advancetec com w g ACVANCEIEC
18. s 1 Part AT8410A Palm Microphone 2 Part AT7107A Privacy Handset with cradle 3 Part AT9298A RED Emergency PTT 4 Part ATAT8408A Antenna GPS 5 Part AT3510A AdvanceMobile Control Module Note A properly installed AdvanceMobile will minimize service calls and equip ment downtime Because of the wide variations in vehicle design these instructions should be modified to suit each particular installation Before beginning the installation process determine the locations for the mounting of the PTT Visor Microphone Speaker and Junction Box and Magnetic Mount Antenna Consider the following guidelines when planning the installation e DOuse all mounting hardware provided DO ensure that cables are not placed under stress DO follow proper and connections DO crimp connectors securely DO NOT attach components to any part of the vehicle that is not rigid or is subject to excessive vibration e DO NOT install components in areas where rain or snow can easily get into them such as next to a vehicle window which may be left open e DO NOT dress cables over sharp edges that could cause wear or tearing of cable insulation e DO NOT install components in locations where they might interfere with the vehicle operator or operating controls e DO NOT install the PTT where it will be difficult for the operator to reach VEHICLES EQUIPPED WITH AIR BAGS An air bag inflates with great force DO NOT place objects inc
Download Pdf Manuals
Related Search