Home

Instructions

1. COSATTO baby stuff with personality cuddly protective pr CD EN www cosatto com Cosatto Ltd a Mill Bentinck Street Farnworth Bolton BL4 7EP England Tel 44 0 871 977 3900 Fax 4410 871 977 3910 Email enquiry cosatto com IMPORTANT RETAIN FOR FUTURE REFERENCE READ CAREFULLY YOUR CHILD S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS user guide Thank you for choosing a Cosatto product Please take a little time to read the important safety notes detailed below This will ensure many years of happy safe use The instruction manual should be kept safely with child car seat for its life period There is a slot at the rear of the child car seat for storage of the instruction manual safety take note WARNING A CHILDS SAFETY IS YOUR RESPONSIBILITY e This child car seat has been approved for mass group 1 2 8 3 which is suitable for transportation in cars of children from 9kg approximately 9 months old up to 36 kg approximately 11 years old e WARNING After an accident the child car seat should be replaced WARNING NEVER use this child car seat on side facing vehicle seat e WARNING NEVER use this child car seat on passenger seat fitted with active airbag e WARNING NEVER leave your child unattended even for the shortest time e WARNING ALWAYS secure your child with the safety harness when using this child car seat e WARNING DO NOT attempt to dismantle m
2. anchoring the child car seat make sure the vehicle seat belt is not twisted in addition the vehicle seat belt must be appropriately tensioned and placed around the child s body to ensure that the child car seat is properly anchored Always make sure that your vehicle seat belts are correctly tensioned to ensure maximum protection for your child 15 removing the covers for cleaning Remove the harness and seat liners if fitted See steps 9 amp 10 Headrest Lift the headrest to the highest position a Starting on one side carefully pull the cover off b Release the belt lock under the headrest c and pull the elastic loop through the gap d Release the elastic loop e Repeat this procedure on the other side of the headrest and remove the headrest cover Seat Starting on one side carefully pull the cover off the seat f At the rear of the backrest lift the elastic strap over the headrest g Push the harness adjuster strap through the elastic loop under the harness adjuster flap h then pull the cover from around the adjuster button i Unclip the six elastic loops holding the cover to the seat j and remove the cover Side impact protection block cover Carefully pull the cover off k IMPORTANT The covers are a safety feature NEVER use the child car seat without them 16 refitting the seat cover Ensure the sponge pad is placed on the seat a Fit the side impact protection block covers by stretching th
3. and pulling the belt lock back Press down on the tab to open the shoulder belt clip g 7 installation of the car seat 9 to 18kg group 1 approx 9 months to 4 years old part 3 Install the vehicle seat belt ensuring that the lap belt fits into the clips at the base of the car seat a and the shoulder belt fits into the shoulder belt clip b nearest the the vehicle seat belt buckle Fasten the vehicle seat belt c Pull the shoulder belt d to remove the slack from the belt Press down on the shoulder belt clip e and close the tab to lock the shoulder belt in place Press down on the lower belt clip f until it locks in place Ensure the retaining rod is correctly located g 8 installation of the car seat 9 to 18kg group 1 approx 9 months to 4 years old part 4 Lift the vehicle seat belt a and push the upper shaft back into position d and under the belt Push the upper shaft into the clip c to lock it in position Close the child car seat and push the lower shaft into position d and lock it in place c Note The upper and lower shaft can be fitted from either side of the child car seat Important The vehicle seat belt MUST fit over the upper shaft e 9 seating your child into the car seat harness Loosen the harness by pushing the adjuster button a in as you pull the shoulder straps b forward as much as possible Important Pull the harness UNDER the chest pads DO NOT pull on the chest p
4. access to the waist harness clips Push the waist harness clip ends through the slots in the child car seat a push the clips through from under the seat b and then through the seat cover Push the crotch harness clip through the slot in the underside of the seat c and then through the seat cover and seat liner The seat liners can now be removed from the child car seat d 12 removing the harness and seat liners part 3 Pull the harness adjuster connector a until the end of the harness adjuster strap fits under the harness adjuster flap b Open the lower belt clip c Push the harness connector through the hole in the lower belt clip d then wrap the adjuster strap around the lower belt clip retaining rod e Place the harness connector under the lower belt clip f Close the lower belt connector taking care not to trap the harness adjuster strap or connector Close the seat and refit the upper and lower locking bars 13 installing the child car seat 15 to 36kg group 2 amp 3 approx 4 to TI years old part 1 Before installation remove the harness and seat liners from the child car seat See steps 9 amp 10 and lock the back of the seat with the upper and lower shafts See step 7 Note The harness chest pads crotch pad 8 chest pad locking bar should be stored away safely for future use The chest pad locking bar MUST NOT be used in group 2 8 3 installations Release the vehicle seat belt lock a
5. adrest to the correct position a The headrest can be set at five different heights in group 1 mode with the chest pad locking bar in place There are four additional positions in Group 2 amp 3 mode once the chest pad locking bar has been removed You can use the harness with your child as long as the shoulder harness fit your child s shoulder correctly To loosen the harness push the adjuster button b in as you pull the shoulder harness forward as much as possible c Important Pull the harness UNDER the chest pads DO NOT pull on the chest pads To tighten the harness pull the adjustment strap forward d 4 adjusting the seat angle The child car seat can be used in five different positions To adjust the recline angle of the seat pull the lever at the front of the seat a then move the seat b Release the handle in the required position and push until you hear a distinct click 5 installation of the car seat 9 to 18kg group 1 approx 9 months to 4 years old part 1 Place the child car seat on the vehicle seat 6 installation of the car seat 9 to 18kg group 1 approx 9 months to 4 years old part 2 Adjust the child car seat to the most reclined position a See step 4 Remove both shafts by releasing the end from its lock b and pulling the shafts out of the seat c Pull the seat forward to gain access to the rear of the seat d Open the lower belt clip by lifting the retaining rod with your finger f
6. ads Unfasten the harness buckle by pressing the red button c and releasing the clips d and open out the belts e Place your child in the child car seat Fit the harness around your child and fasten the harness buckle by joining the clips f and pushing them both into the buckle g Check that the harness is not twisted and pull the harness up h to tighten the lap sections which is designed to fit low down on your child s body Pull the adjuster strap forward i making sure the harness is a comfortable but FIRM fit around your child Finally pull both chest pads down j from your child s shoulders onto their chest Note The chest pads are an important safety feature Never use the child car seat without them 10 removing the harness and seat liners part 1 Open the seat to gain access to the rear See step 5 Loosen the harness See step 3 At the rear of the seat remove the shoulder harness from the harness connector a Lift the shoulder harness to gain better access to the chest pad locking bar Release the chest pad locking bar on the rear of the seat b by pulling it backwards sharply 5 Pull the shoulder harness from the front of the child car seat d until the shoulder harness and chest pad straps come through the backrest of the seat e ide the chest pad straps off the chest pad locking bar c 11 removing the harness and seat liners part 2 Lift the bottom part of the seat cover to gain
7. e cover over the impact pads b Place the cover on the seat Fit the elastic strap over the headrest c Fit the six elastic loops on the inside of cover to the mounting points on the seat d Fit the cover around the adjuster button e then push the harness adjuster strap through the elastic loop under the harness adjuster flap f Stretch the cover over the seat and backrest g ensuring the elastic edging tucks inside the seat structure and secures the cover to the seat 17 refitting the headrest cover Fit the elastic loop a through the slot in the vehicle seat belt lock Fit the elastic lool under the vehicle seat belt lock b Close the vehicle seat belt lock c Stretch the cover over the headrest d ensuring the elastic edging tucks inside the headrest structure and secures the cover to the headrest 18 refitting the harness for group 1 use part 1 If reguired release the harness adjuster strap Open the seat to gain access to the rear See step 5 Open the lower belt clip a and unwrap the harness adjuster strap from the lower belt clip retaining rod b Push the harness connector through the hole in the lower belt clip c then from the front of the child car seat pull the harness adjuster strap out from under the harness adjuster flap d Close the lower belt clip Close the seat and refit the upper and lower locking bars 19 refitting the harness for group 1 use part 2 Release the harness from the r
8. estraint system if reguired Feed the crotch harness through the slot in the seat liner and seat cover a Push the crotch harness clip through the slot in the seat b Flatten the clip to secure Fit the waist harness clips through the slots in the seat cover and seat c Push the clips through the seat and back up from underneath d Flatten the clips to secure Loosening the cover around the waist harness mounting points will help with access 20 refitting the harness for group 1 use part 3 Feed the shoulder harness through the chest pads then push the straps through the slots in the upper seat liner and backrest a Slide the chest pad straps onto the chest pad belt locking bar at the rear of the backrest b Push the chest pad locking bar into the backrest until it s locked in place c Fit the ends of the shoulder harness to the harness connector d care Your child car seat has been designed to meet safety standards and with correct use and maintenance will give many years of trouble free performance Storing a damp child car seat will encourage mildew to form After exposure to damp conditions dry off with a soft cloth and allow to dry thoroughly before storing Store your child car seat in a dry safe place Do not leave the child car seat in sunlight for prolonged periods some fabrics may fade maintenance This child car seat reguires regular maintenance by the user DO NOT take apart or attempt to take apa
9. han the ones recommended by Cosatto Safely secure any luggage and other objects that might cause injury to the occupant of the child car seat in the event of a crash e After an accident replace your child car seat and the vehicle seat belts Although they may look undamaged they may not protect your child as well as they should Cosatto advise that child car seats should not be brought or sold second hand Many seats sold through local advertising and car boot sales have been found to be dangerous e Prevent harness vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body e If the harness vehicle belts becomes cut or frayed replace it before travelling e If the vehicle has been left in the sun for a long time check the seat cover and make sure it is not too hot before placing the child in the child car seat e Security is only guaranteed if the child car seat is fitted in accordance with these instructions e Failure to comply with the above instructions will automatically void the warranty and exempt Cosatto from any liability storage of instruction manual The instruction manual should be kept safely with child car seat for its life period There is a slot at the rear of the child car seat for storage of the instruction manual notice 1 This is a Universal child restraint It is approved to Regulation No 44 04 series of amendments for general use in vehicles and it wi
10. ll fit most but not all car seats 2 A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable of accepting a Universal child restraint for this age group 3 This child restraint has been classified as Universal under more stringent conditions as those which applied to earlier designs which do not carry this notice 4 This child restraint is only suitable if the vehicle is fitted with a type approved leg 3 point stetie with retractor safety belt in compliance with standard UN ECE Regulation No 16 or other eguivalent standards 5 If in doubt consult either the child restraint manufacturer or retailer operation 1 getting to know your child car seat 1 Headrest 6 Crotch pad 11 Lower shaft 2 Upper seat liner 7 Harness adjuster flap 12 Pocket for instructions 3 Chest pads 8 Harness adjuster strap 13 Side impact protection block 4 Lower seat liner 9 Headrest adjuster lever 5 Harness 10 Upper shaft 2 approved seatbelt reguirement WARNING Your child car seat can only be installed forward facing using a three point lap and diagonal belt in the front or rear passenger seats of the car 3 adjusting the harness The shoulder harness must fit at the top of your child s shoulders The height of the shoulder harness can be raised or lowered by adjusting the height of the headrest Squeeze the lever at the back of the headrest and raise or lower the he
11. odify or add to any part of the child car seat or change the way your vehicle seat belts are made or used e WARNING Any rigid items and plastic parts of the child car seat must be so located and installed that they are not liable during everyday use of the vehicle to become trapped by a movable seat or in a door of vehicle e WARNING If any load bearing points other than those described in the instructions are used this can significantly reduce the protection factor of the child car seat e WARNING DO NOT use the child car seat in the home It has not been designed for home use and should only be used in your car e The child car seat must always be placed in a forward facing position e Always make sure that the child car seat harness and vehicle belt are correctly tensioned to ensure maximum protection for your child The buckle has been designed to be released guickly in an emergency IT IS NOT CHILD PROOF More inguisitive children might learn to undo the buckle Children should be told never to play with it or any other part of the child car seat e Never use replacement parts other than those approved by Cosatto e In Group 2 amp 3 modes the lap belt must be worn in such a way as to properly secure the pelvis of the child e Never use the child car seat without its fabric cover because the seat cover constitutes as an integral part of the child car seat performance The seat cover should not be replaced with any other t
12. res cosatto com Headrest cover Upper seat liner Lower seat liner Upper lower shaft Side impact protection block cover U N TI 8 1 Q l r Da Q o AGN UP SIGN UP U gt join our VIP club 7 SW catch onto the newsletter at cosatto com Keep in the lovely loop for regular crazy competitions exclusive viewings of future stuff n giveaways and exclusive invitations Tell your friends too the GR do 30 enter agota cosatto com 3towin join the conversation Cosatto_Tweets follow us on facebook com clubcosatto
13. rt any of the harness when cleaning the harness and seat It is unnecessary and dangerous to do so Food and drink may find their way inside the buckle of the harness This can stop it working properly Clean the harness buckle with mild hand soap and water Rinse thoroughly with warm water Latch and unlatch the tongues of the buckle several times until a strong click is heard If you cannot hear a strong click run it under warm water to rinse again If the harness vehicle belts becomes cut or frayed replace it before travelling cleaning The harness may be cleaned by sponging lightly using warm water and a mild detergent Plastic and metal parts may be sponged clean with warm water and a mild detergent Never clean with abrasive ammonia based bleach based or spirit type cleaners Cleaning the covers Please read the labels on the covers for washing instructions The seat covers can be removed easily for washing The seat covers can be machine washed with a mild detergent at 30 C Don t wring spin or iron the seat covers Clean plastic shell of the child car seat by wiping it with a damp cloth replacement parts The replacement parts shown below are available for your product In the event that you reguire any of these parts please contact your local distributor For the contact information for your local distributor please refer to http www cosatto com stockists If you are a UK or Ireland customer please contact us at spa
14. under the headrest Feed the vehicle seat belt into the gap b under the vehicle seat belt slot until the vehicle seat belt is located in the vehicle seat belt slot Push the vehicle seat belt lock back c 14 installing the child car seat 15 to 36kg group 2 8 3 approx 4 to TI years old part 2 Place your child in the child car seat and fasten the vehicle seat belt Pull the vehicle seat belt upwards to tension the belt a The vehicle seat belt should be positioned between your child s shoulder and neck b If the vehicle seat belt is in the correct position the lap belt should fit over the red tags sewn into the cover on either side of the seat c The height of the vehicle seatbelt can be adjusted by sgueezing the lever at the back of the headrest and raising or lowering the headrest to the correct position d For the safety of the child please check e The diagonal belt section runs through the seat belt guide located on the headrest and the lap belt must pass over the red tags sewn into the seat cover e The straps are tightened and not twisted e The vehicle seat belt buckle is correctly located on the side of the car seat and is not obstructed Always make sure that your vehicle seat belts are correctly tensioned to ensure maximum protection for your child Anchorage Group 2 and 3 The shoulder belt must cling to the child s shoulder and chest The lap belt must pass over the red tags sewn into the seat cover When

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents