Tiger Series User Manual
Contents
1. 2 The pump does not A The pipes are obstructed A Remove the obstructions as deliver indicated in the Warnings chapter Paragraph 6 4 B The impellers are worn or blo B Change the impellers or remove cked the obstruction C The fluid level is too low C Regulate the length of the On starting the water level must float switch cable See chap be higher than the filter level ter on Warnings Paragraph 9 2 D The head required is higher than thepump s characteristics 3 The pump does not A The float does not interrupt A Make sure float moves freely stop the operating of the pump and check its efficient 29 FAULT CHECK Possible cause REMEDY 4 The flow rate is insufficient A Ensure that the impellers or the delivery pipe are not partly blocked or fouled with scale B Ensure that the impellers are not worn C Check the direction of rotation in three phase versions See Chapter on Electrical connection Paragraph 8 4 A Check good operation of the valve and replace it if necessary B Change the impellers C Invert two wires in the power cable 5 The overload protec tion device stops the pump A Ensure that the fluid to be pumped is not too dense because it would cause overheating of the motor B Ensure that water temperature is not too high see liquid tem perature range C The pump is partly blocked by impurities D The pump is mechanicall2. MAINTENANCE AND CLEANING MODIFICATIONS AND SPARE PARTS TROUBLESHOOTING TECHNICAL DATA 22 22 22 22 23 24 25 25 26 26 27 27 28 28 28 29 29 29 30 31 37 1 GENERAL POINTS Read this documentation carefully before installation Installation and functioning must comply with local and national safety regulations in force in the country where the product is to be installed The entire operation must be carried out in a workmanlike manner Failure to comply with the safety regulations not only causes risk to personal safety and da mage to the equipment but also invalidates any right to warranty assistance Keep this manual in a safe place for further consultation even after the first installation 2 APPLICATIONS These motor pumps TIGER TIGER BC SKIPPER ARVEX amp ARVEX BO are used in ap paratus for hoisting clear and dirty water from wells for emptying settling beds for pumping water also in the presence of suspended solid bodies and for pumping aggressive liquids ARVEX AISI 316 only The particularly silent motor pumps installed inside wells or tanks avoid all problems related to suction and depriming The motor pump can be supplied with a floating switch should it be necessary to turn it off in case of inadequate water level These pumps cannot be used in swimming pools ponds or tanks in which people are present or for pumping hydrocarbons petrol diesel fuel fuel
3. without changing the essential characteristics of the product itsef 7 INSTALLATION 7 1 SITE OF INSTALLATION Pumps marked with maximum liquid temperature C which not less than 35 C Before immersing the electropump in the pit or tank ensure that the place is free from sand or solid sediment n case there is sediment accurately clean the site where it is to be placed Keep the pump at least 1 mt raised above the bottom of the pit so that any deposits that form after installation will not be sucked up Remove the sediment periodically e t is very important to ensure that the water level never falls below the body of the pump 7 2 WORKING CONDITIONS Pump body always completely immersed The pump cannot operate dry Installation in vertical or horizontal position The housing pit must be frost free Maximum depth of immersion 5 mt below water level 7 3 PIPING Put the pump into the liquid to be pumped Inspect for the max pumping height refer to the performance curve The hydraulic connection of the pump may be made with iron or plastic parts either rigid or flexible Avoid any kind of choking of the output pipe t is advisable to use pipes with an internal diameter at least equal to that of the delivery pipe so as to avoid a fall in the performance of the pump and the possibility of clogging For the version with a float switch ensure that the latter
4. and maintenance jobs must be carried out only after having disconnected the pump from the power mains once made sure that it cannot suddenly begin working During dismantling it is necessary to pay great attention to sharp parts which may cause injury The cut ting edge flange of the electropump is provided of aspiration fans It is advisable every now and then to clean these fans to avoid a loss of efficiency Best cleaning is obtained through a throw of water Sand and other abrasive materials cause precocious wear and tear as well as loss of performances 12 MODIFICATIONS AND SPARE PARTS Any modification not authorized beforehand relieves the manufacturer of all responsibility All the spare parts used in repairs must be original ARVEN For codes and denominations see enclosed sheet All accessories must be approved by the manufacturer so as to be able to ensure maximum safety of the machines and systems in which they may be fitted 13 TROUBLESHOOTING FAULT CHECK possible cause REMEDY 1 The motor does not start and makes no noise A Make sure motor is live and check that the mains voltage cor responds to the one on the data plate B Check the protection fuses C The float switch prevents starup D The shaft is not turning B If they are burnt out change them C Make sure float moves freely and check its efficiency D Turn the shaft as indicated in the Warnings chapter Paragraph 6 3
5. at 8 ELECTRICAL CONNECTIONS CAUTION ALWAYS FOLLOW THE SAFETY REGULATIONS VAN 8 1 The electrical installation must be carried out by an authorized and competent electri cian who assumes all the responsibilities 8 2 Ensure that the mains voltage is the same as shown on the plate of the motor to be fed and be sure TO MAKE A GOOD GROUND CONNECTION 8 3 The electropump both the single phase and the three phase version is supplied with an electric cable If the power cable is damaged in any way it must be replaced not repaired t is advisable to connect the pump to a dedicated power line Upstream from the pump fit a suitably sensitive magnetothermal differential switch e Switch off the power upstream from the system before making the electrical connection e Single phase motors are provided with built in thermal overload protection and may be con nected directly to the mains Warning If the motor is overloaded it stops automatically Once it has cooled down it starts again automatically without requiring any manual intervention eThree phase pumps must be protected with motor protectors suitably calibrated according to the values on the data plate of the pump to be installed eConnect the pump cable to the electric panel ensuring that the following parts correspond SINGLE PHASE Yellow green eZ Brown gt LI Blue gt N Before making a test start check the water level inside the well 8 4 CHEC
6. can move freely see Paragraph 9 2 REGULATING THE FLOAT SWITCH The size of the pit must always be calculated in relation to the quantity of incoming water and to the flow rate of the pump so as not so subject the motor to an excessive number of starts To lower the pump always use a rope or chain fixed be forehand to the upper handleo on top of the pump NEVER USE THE POWER CABLE TO LIFT THE ELECTRO EUNE When using in deep wells it is advisable to secure the power cable to the delivery pipe with clamps every two three metres INSTRUCTIONS FOR SAFE USE This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack experience and knowledge unless they have been given supervision or instruction Children should be supervised to ensure that they do not play with the appliance The pump must be supplied through a residual current device RCD with a rated residual operating current lt 30 Ma ARVEX amp ARVEX BC ETE 360 mm o max BRE j immersione amp STOTT TIO IO OOOO WARNING The pump should not be run dry It should be put fully into the liquid to be pumped Slurping for long periods should be avoided which the pump may be used n The length of the power cable on the electropump limits the maximum depth of immersion
7. 3 Phases Electric connection voltage Hz 220 230 V 50 Hz 380 400 V 50 Hz 220 230 V 50 Hz 380 400 V 50 Hz 220 230 V 50 Hz 380 400 V 50 Hz Power rating P1 Kw ES Ge Current absorption A SO d x Max High head pressure mt 10 5 10 5 13 Max capacity l min 230 400 425 Max temperature of liquid C 50 50 50 Horizontal suction mm 85 85 85 Max submersion depth mt 5 5 5 N of impellers 1 1 1 Electric cable mt 5 10 5 10 5 10 Foreign bodies aspir up to o mm 30 50 50 Discharge connection thread DNM 2 2 2 Pump dimension BxD mm 176 x 358 176 x 358 176 x 398 Packing dimension LxMxN mm 190 x 230x410 190x230x410 190 x 230 x 410 Weight Kg 10 5 11 5 13 5 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding TECHNICAL DATA ARVEX 80 AISI 304 1 Phase 3 Phases ARVEX 100 AISI 304 1 Phase 3 Phases Electric connection voltage Hz 220 230 V 50 Hz 380 400 V 50 Hz 220 230 V 50 Hz 380 400 V 50 Hz Power rating P1 Kw b f Current absorption A SA ba Max High head pressure mt 9 5 10 5 Max capacity l min 300 400 Max temperature of liquid C 50 50 Horizontal suction mm 85 85 Max submersion de
8. Automatically when water level rises for versions with a float switch 21 Float locking wire AN 9 2 FLOAT SWITCH SETTING By lengthening or shortening the stretch of cable between the float and the fixed point Float locking it is possible to regulate the level at which the pump switches off Ensure that the float witch can move freely when the pump is operating TIGER TIGER BC SKIPPER Float locking N all Bed eee wire Fig 3 10 PRECAUTIONS The pump must not be started more than 15 time in one hour so as not to subject the motor to ex cessive thermal stress eDANGER OF FROST When the pump remains inactive at temperatures of less than 0 C it is necessary to ensure that there is no water residue which might freeze and cause cracking of the pump components e f the pump has been used with substances that tend to deposit rinse it after use with a powerful jet of water so as to avoid the formation of deposits or scale which would tend to reduce the pump characteristics 11 MAINTENANCE AND CLEANING In normal operation the pump does not require any type of maintenance thanks to the oil bath lubricated seal and to the greased for life bearings The electropump can only be dismantled by skilled and qualified personnel in possession of the technical qualifications required by the specific regulations in force 28 AN In any case all repair
9. KING THE DIRECTION OF ROTATION for three phase motors TIGER TIGER BC SKIPPER ARVEX ARVEX BC Fig 2 CAUTION ALWAYS FOLLOW THE SAFETY REGULATIONS The direction of rotation must be checked each time a new installation is carried out Proceed as follows 1 Place the pump on a flat surface 2 Start the pump and stop it immediately 3 Carefully observe the kick back on starting looking at the pump from above If the direction of rotation is correct the upper cap will turn counter clockwise as indicated by the arrows in the drawing Fig 2 If it is not possible to check as described above because the pump is already installed check as fol lows 1 Start the pump and observe the water flow rate 2 Stop the pump switch off the power and invert two phases on the supply line 3 Restart the pump and check the water flow rate again 4 Stop the pump The correct direction of rotation is the one that gives the higher flow rate 9 START UP 9 1 Turn the differential magnetothermal switch upstream from the pump to position ON and wait until the water comes out of the delivery pipe e f malfunctions are found disconnect the pump from the power supply turning the differential magnetothermal switch to position O OFF and consult the chapter on TROUBLESHOOTING para graph 13 The pump may be started and stopped Manually by means of the differential magnetothermal switch upstream from the system
10. N CHECK If the motor does not work when the switch is enabled and the shaft does not turn make sure that the moving parts are rotating freely For this reason Disconnect completely the motor pump from the electric system Place the motor pump horizontally Turn the motor shaft clockwise by using an open end wrench no 13 and acting on the self locking nut through the hole under the pump Turn over the motor pump and install it as indicated in chapter 7 6 4 MOTOR SHAFT ROTATION CHECK If the motor does not work when the switch is enabled and the shaft does not turn make sure that the moving parts are rotating freely For this reason Disconnect completely the motor pump from the electric system Place the motor pump horizontally Remove the supporting base Turn the motor shaft clockwise by using an open end wrench no 13 and acting on the self locking nut 23 AN 6 5 RESPONSIBILITY The Manufacturer does not vouch for the correct operation of the pumps and will not be responsible for damages that might be caused by them in case they are tampered with or modified run outside the recommended work range or in contrast with the other instructions given in this manual The Manufacturer assumes no liability resulting from or omissions in this booklet if due to misprints or errors in copying The company reserves the right to make mo difications to the products described herein when considered necessary or useful
11. TIGER BC SKIPPER ARVEX dlae Soldi daga e oa 98 ARVEX BC TIGER Arar zmmpy ARVEN s r l via Artigiani n 10 25030 VE MACLODIO Brescia ITALIA C 4 Tel 030 9973973 Fax 030 9973975 DECLARATION OF CONFORMITY ISSUED ON NOVEMBER 20TH 2013 The company ARVEN s r l via Artigiani n 10 25030 MACLODIO BS ITALY under its own responsibility decla res that the pumps TIGER TIGER BC SKIPPER ARVEX amp ARVEX BC are in accordance with the following directives Directive on electromagnetic compatibility 2004 108 CE and subsequent revisions Directive on Low voltage 2006 95 CE and subsequent revisions Machines directive 2006 42 CE and subsequent revisions ROHS 2002 95 CE directive for the restrictions on the use of dangerous substances in electrical and electronical equipment Marcello Grazioli Technijgal amp Quality Dept INDEX 1 2 5 1 5 2 6 1 6 2 6 3 6 4 6 5 7 1 7 2 7 3 8 4 9 2 10 11 12 13 14 GENERALS POINT APPLICATIONS PUMPED FLUIDS TECHNICAL DATA AND USE LIMITATION MANAGEMENT Storage Transport WARNINGS Qualified personnel Safety Motor shaft rotation check Motor shaft rotation check Responsibility INSTALLATION Installation site Working conditions Piping ELECTRICAL CONNECTION 8 1 8 2 8 3 Checking the direction of rotation for three phase motors STARTING UP 9 1 Float switch regulating PRECAUTIONS
12. and not binding TECHNICAL DATA ARVEX BC 100 1 Phase 3 Phases ARVEX BC 150 1 Phase 3 Phases ARVEX BC 200 1 Phase 3 Phases Electric connection voltage Hz 220 230 V 50 Hz 380 400 V 50 Hz 220 230 V 50 Hz 380 400 V 50 Hz 380 400 V 50 Hz Power rating P1 Kw b Ee 22 Current absorption A E 1 A f 5 48 Max High head pressure mt 11 5 14 5 16 Max capacity l min 500 600 700 Max temperature of liquid C 50 50 50 Horizontal suction mm 70 70 70 Max submersion depth mt 5 5 5 N of impellers 1 1 1 Electric cable mt 5 10 5 10 5 10 Foreign bodies aspir up to o mm 50 50 50 Discharge connection thread DNM 2 2 2 Pump dimension BxD mm 176 x 369 176 x 409 176 x 409 Packing dimension LxMxN mm 190x230x480 190x230 x 480 190 x 230 x 480 Weight Kg 12 5 14 5 14 5 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding JV ARVEN ARVEN S r l Via Artigiani n 10 25030 Maclodio Brescia Italy Tel 39 030 9973973 Fax 39 030 9973975 e mail info arven it www arven it
13. ght to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding SKIPPER 80 SKIPPER 100 SKIPPER 150 SKIPPER 200 TECHNICAL DATA 1 Phase 1 Phase 1 Phase 1 Phase 3 Phases 3 Phases 3 Phases 3 Phases Electric connection voltage Hz GE be dis GE Ke i su eet ius in da E z z 380 400 V 50 Hz 380 400 V 50 Hz Power rating P1 Kw SO ba de 22 Current absorption A j Sa Ea 36 Max High head pressure mt 7 5 8 5 11 13 Max capacity l min 260 400 450 500 Max temperature of liquid C 50 50 50 50 Horizontal suction mm 150 150 150 150 Max submersion depth mt 5 5 5 5 N of impellers 1 1 1 1 Electric cable mt 5 10 5 10 5 10 5 10 Foreign bodies aspir up to e mm 35 50 50 50 Discharge connection thread DNM dz 2 2 2 Pump dimension BxD mm 164 x 355 164 x 355 164 x 395 164 x 395 Packing dimension LxMxN mm 190 x 230 x 410 190 x 230 x 410 190 x 230 x 410 190 x 230 x 410 Weight Kg 10 5 11 5 13 5 13 5 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding TECHNICAL DATA ARVEX S 80 AISI 316 1 Phase 3 Phases ARVEX S 100 AISI 316 1 Phase 3 Phases ARVEX S 150 AISI 316 1 Phase
14. ir up to o mm 30 35 50 50 50 Discharge conn thread DNM ITE biz 2 2 2 Pump dimension BxD mm 150 x 360 5 150 x 372 5 150 x 385 5 150 x 395 5 150 x 395 5 Packing dim LxMxN mm 190x230 x 410 190 x 230 x 410 190 x 230 x 410 190 x 230 x 480 190 x 230 x 480 11 12 13 15 15 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding TECHNICAL DATA TIGER BC 100 1 Phase 3 Phases TIGER BC 150 1 Phase 3 Phases TIGER BC 200 1 Phase 3 Phases Electric connection voltage Hz 220 230 V 50 Hz 380 400 V 50 Hz 220 230 V 50 Hz 380 400 V 50 Hz 380 400 V 50 Hz Power rating P1 Kw i Ze 22 Current absorption A Sa A 5 48 Max High head pressure mt 11 5 14 5 16 Max capacity l min 500 600 700 Max temperature of liquid C 50 50 50 Horizontal suction mm 65 65 65 Max submersion depth mt 5 5 5 N of impellers 1 1 1 Electric cable mt 10 10 10 Foreign bodies aspir up to o mm 50 50 50 Discharge connection thread DNM 2 2 25 Pump dimension BxD mm 150 x 367 150 x 407 150 x 407 Packing dimension LxMxN mm 190 x 230 x 480 190 x 230 x 480 190 x 230 x 480 Weight Kg 14 16 16 The characteristics and technical data are not binding Arven reserves the ri
15. oils solvents etc in accordance with the accident prevention regulations in force N B The liquid employed in the pump for lubricating the sealing device is not toxic but it could alter the water properties in the case of pure water if there were any leaks in the seal 3 PUMPED FLUIDS The machine has been designed and built for pumping water free from explosive substances and solid particles or fibres with a density of 1 Kg dm3 and a kinematic viscosity of 1mm2 s and chemically non aggressive liquids 4 TECHNICAL DATA AND USE LIMITATIONS Supply voltage see electric data plate Absorbed power see electric data plate Maximum working pressure 1 5 Bar Pumped fluid solids and abrasive substances for only ARVEX AISI 316 not aggressive Degree of motor protection IE 68 Thermal class F Liquid temperature range from 0 C to 25 C with pump part submerged from 25 C to 35 C with pump full submerged Maximum immersion 5 metres Storage temperature from 10 C to 40 C Noise level noise level is contained within the limits envisaged by EC Directive EC 89 392 CEE and subsequent modifications 70 dB Motor constructions in accordance with CEI 2 3 CEI 61 69 EN 60335 2 41 standards 22 gt 5 MANAGEMENT 5 1 STORAGE All the pumps must be stored indoors in a dry vibration free and dust free environment pos sibly at constant air humidity They are supplied in their
16. original packaging and must be kept there until installation 5 2 TRANSPORT Avoid subjecting the products to needless jolts or collisions The electropumps must never be carried or lifted by their power cables 6 WARNINGS 6 1 QUALIFIED PERSONNEL Installation should be performed by skilled and qualified personnel in possession of the technical qualifications required by the specific regulations in force The term qualified personnel means persons who because of their training experience and regulations as well as all operating circumstances have been entitled by the person responsible for the system to work on and with the system and to see and avoid all possible dangers Defi nition for technical personnel Definition for technical personnel IEC 364 6 2 SAFETY Use is allowed only if the electric system is provided with safety precautions in accordance with the regulations in force in the country where the product is installed for Italy CEI 64 2 Never let the pump run dry The pump cannot be used in swimmingpools ponds or tanks in which people are present The pump is provided with a handle to which a rope or cable may be connected to lower the machine into working position The pumps must never be carried lifted or operated hanging from their power cables Qualified personnel must be employed for all electrical repairs which if badly carried out could cause damage and accidents 6 3 MOTOR SHAFT ROTATIO
17. pth mt 5 5 NE of impellers 1 1 Electric cable mt 5 10 5 10 Foreign bodies aspir up to mm 50 50 Discharge connection thread DNM qe 2 Pump dimension BxD mm 176 x 358 176 x 358 Packing dimension LxMxN mm 190 x 230 x 410 190 x 230 x 410 Weight Kg 10 5 11 5 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only and not binding TECHNICAL DATA ARVEX 150 AISI 304 1 Phase 3 Phases ARVEX 200 AISI 304 1 Phase 3 Phases Electric connection voltage Hz 220 230 V 50 Hz 380 400V 50 Hz 380 400 V 50 Hz Power rating P1 Kw E 22 Current absorption A be 37 Max High head pressure mt 13 14 Max capacity l min 425 450 Max temperature of liquid C 50 50 Horizontal suction mm 90 90 Max submersion depth mt 5 5 NE of impellers 1 1 Electric cable mt 5 10 5 10 Foreign bodies aspir up to o mm 50 50 Discharge connection thread DNM d qi Pump dimension BxD mm 176 x 398 176 x 398 Packing dimension LxMxN mm 190 x 230 x 480 190 x 230 x 480 Weight Kg 13 5 13 5 The characteristics and technical data are not binding Arven reserves the right to make modifications without notice Therefore weights dimensions performances and any other stated issues are indicative only
18. y blocked B Reduce liquid temperature Wait until thermal protection Switch resets about 20 mins C Accurately clean the pump D Check for the occurrence of rubbing between moving and fixed parts check the state of wear of the bearings contact the supplier DON T DISPOSE OF WORN OUTS UNITS THROUGH THE HOUSEHOLD GARBAGE The appliance its packaging and accessories are all produced from recyclable materials and must be disposed of accordingly in the suita ble dispose places adhering itself to the modalities previewed from the enforced norms in matter 14 TECHNICAL DATA TECHNICAL DATA TIGER 70 1 Phase 3 Phases TIGER 80 1 Phase 3 Phases TIGER 100 1 Phase 3 Phases TIGER 150 1 Phase 3 Phases TIGER 200 1 Phase 3 Phases Electric connection voltage 220 230 V 50 HZ 220 230 V 50 HZ 380 400 V 50 Hz 220 230 V 50 HZ 380 400 V 50 Hz 220 230 V 50 HZ 380 400 V 50 Hz 380 400 V 50 Hz Weight Kg 0 9 Al 1 5 2 2 T Power rating P1 Kw 0 9 1 3 17 22 4 0 5 0 6 5 10 4 B Current absorption A si 2 0 24 3 0 3 6 Max High head pressure mt 6 5 7 5 8 5 11 13 Max capacity l min 200 260 400 450 500 Max temp of liquid C 50 50 50 50 50 Horizontal suction mm 150 150 150 150 150 Max submersion depth mt 5 5 5 5 5 N of impellers 1 1 1 1 1 Electric cable mt 5 10 5 10 5 10 5 10 5 10 Foreign bod asp
Download Pdf Manuals
Related Search